Microporous membranes obtained from polypropylene blends with superior permeability properties

A blend of two polypropylene resins, different in molecular structure, one with linear chains and the other with long chain branches, was investigated to develop microporous membranes through melt extrusion (cast film process) followed by film stretching. The branched component significantly affected the row‐nucleated lamellar crystalline structure in the precursor films. The arrangement and orientation of the crystalline and amorphous phases were examined by wide angle X‐ray diffraction and Fourier transform infrared spectroscopy methods. It was found that blending of a small amount of a long chain branched polypropylene improved the orientation of the both crystalline and amorphous phases in the precursor films. Annealing, followed by cold and hot stretching were consequently employed to generate and enlarge pores in the films as a result of lamellae separation. SEM micrographs of the surface of the membranes obtained from the blend revealed elongated thin fibrils and a large number of lamellae. The lamellae thickness for the blend was much shorter in comparison to that of the linear PP precursor film. The permeability of the samples to water vapor and N₂ was significantly enhanced (more than twice) for the blend system. The porosity of the blend membrane showed a significant improvement with a value of 53% compared to 41% for the linear PP membrane. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 148–157, 2008     

Influence of the molecular architecture of low‐density polyethylene on the texture and mechanical properties of blown films

Three types of low‐density polyethylene materials were investigated with respect to the influence of the molecular architecture on the mechanical and use properties of blown films. The materials were a branched polyethylene synthesized by free‐radical polymerization under high‐pressure (HP‐LDPE), a linear ethylene–hexene copolymer (ZN‐LLDPE) produced by low‐pressure Ziegler–Natta catalysis, and an ethylene–hexene copolymer (M‐LLDPE) from metallocene catalysis. The extrusion and blowing conditions were identical for the three materials, with a take‐up ratio of 12 and a blow‐up ratio of 2.5. The blown films displayed a decreasing puncture resistance in the order M‐LLDPE, ZN‐LLDPE, and HP‐LDPE. In parallel, the tear resistance of the films became increasingly unbalanced in the same order of the polymers. The morphological study showed an increased anisotropy of the films in the same polymer order, the crystalline lamellae being increasingly oriented normal to the take‐up direction. This texturing caused a detrimental effect on the mechanical properties of the films, notably increasing the capacity for crack propagation. The phenomenon was ascribed to the kinetics of chain relaxation in the melt that governed the ability of the chains to recover an isotropic state from the flow‐induced stretching before crystallization. The puncture resistance was examined in terms of both texture and strain‐hardening capabilities. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 327–340, 2003     

Oriented lamellar structures in uniaxially drawn films of poly(vinylidene fluoride) and poly(3‐hydroxybutyrate) blends studied by small‐angle X‐ray scattering measurements

The lamellar structures in uniaxially drawn films of miscible crystalline/crystalline polymer blends of poly(vinylidene fluoride) (PVDF) and poly(3‐hydroxybutyrate) (PHB) were investigated by static and time‐resolved measurements of small‐angle X‐ray scattering (SAXS). Intense SAXS in the low angle range of the meridian was interpreted as originating from the interlamellar inclusion structure, in which the PHB chains were included between the lamellae of PVDF. The interlamellar inclusion was induced for the uniaxially drawn films of PVDF/PHB = 30/70 blend with a draw ratio (DR) of 2.8–4.5, whereas the lamellae of the PVDF and PHB components were mutually excluded from each other forming their own lamellar stacks (interlamellar exclusion) in the blend with a higher DR (5.0–5.7). When the highly drawn film with the interlamellar exclusion structure was heat treated at 154–165 °C, the interlamellar inclusion structure was partially induced by the heat treatment. The time‐resolved SAXS measurements indicated that the interlamellar inclusion structure was developed by melting and recrystallization of PVDF during the heat treatment. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 381–392, 2009     

高分子量级分含量对熔体挤出拉伸法制备聚丙烯微孔膜的影响

通过熔体挤出拉伸法以两种聚丙烯为原料制备微孔膜.通过考察原料分子量数据发现高分子量聚丙烯(PPH)在高分子量级分(重均分子量>106)含量上大于低分子量聚丙烯(F401).PPH的弛豫时间在相同条件下也远大于F401.红外二向光法结果表明,PPH在相同熔体牵伸比下片晶取向度较F401高.相同加工条件下PPH微孔膜片较F401成孔分布更均匀,孔径尺寸也更均匀.2种微孔膜孔隙率都随熔体牵伸比的增加而提高,微孔分布随着熔体牵伸比的提高和片晶取向度的增加而趋于均匀,孔尺寸也随之区域均匀.研究表明,聚合物树脂中高分子量级分含量是影响预制膜中片晶取向度、冷热拉伸成孔分布和尺寸均匀度的重要影响因素.     

Effect of strain‐induced molecular ordering on mechanical performance and barrier properties of polylactide nanocomposites

Plastic deformation of polylactide has been known as a self‐reinforcement alternative to improve mechanical and barrier properties. In this study, the structural evolution was investigated during a hot‐drawing process, at different initial strain rates and temperatures above T_g of polylactide. The drawing process at T_g +10 °C, led to the formation of an intermediate molecular ordering, between the crystalline and amorphous phases. A lower fraction of this mesomorphic phase was found to develop with the addition of nanoparticles. An increase in the stretching temperature to T_g +30 °C, caused an improvement of the crystallization kinetics, compared to that of thermally activated crystallization. A strain hardening behavior was observed in the presence of mesophase during a stretching process of the hot‐drawn films at room temperature. Permeability was discerned to its basic components, diffusivity, and solubility coefficients. The matrix degradation influenced the permeability components. The diffusivity decreases in the presence of the impermeable matters. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1865–1876     

Fabrication of microporous membranes from melt extruded polypropylene precursor films via stretching: Effect of annealing

In this work, the effects of annealing conditions on the microstructure of polypropylene(PP) precursor films and further on the porous structure and permeability of stretched membranes were investigated. Combinations of WAXD, FTIR, DSC and DMA results clearly showed the crystalline orientation and crystallinity of the precursor film increased with annealing temperature, while the molecular chain entanglements in the amorphous phase decreased. Changes in the deformation behavior suggested more lamellar separation occurred for the films annealed at higher temperatures. Surface morphologies of the membranes examined by SEM revealed more pore number and uniform porous structure as the annealing temperature increased. In accordance with the SEM results, the permeability of the membranes increased with annealing temperature. On the other hand, it was found that 10 min was almost enough for the annealing process to obtain the microporous membranes with an optimal permeability.     

Partially miscible EVOH/copolyamide‐6/6.9 blends: The effect of stretching on the structure

Binary blends of random copolymers, ethylene‐vinyl‐alcohol (EVOH) consisting of 38 mol % ethylene and Copolyamide‐6/6.9 with an approximate 1 : 1 comonomer ratio, were prepared via blown‐film extrusion and uniaxial stretching. The anisotropy induced by the uniaxial deformation of the polymer blends was characterized by X‐ray diffraction and birefringence measurements. The stretched films also were investigated via oxygen permeability. The results showed a sharp decrease in the apparent crystallite size throughout the entire composition range in comparison to the blown films. However, the order perceived within the amorphous phase in the EVOH‐rich blends increased (decrease in oxygen permeability), whereas in the copolyamide‐rich blends, orientation resulted in a decrease in the amorphous phase order (increase in permeability). Apparently, orientation destroyed the amorphous interpolymer complex. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 813–822, 2000     

Relationship between fracture toughness and intrinsic deformation parameters in isotropic and flow‐oriented linear low‐density polyethylene

The fracture toughness of isotropic and flow‐oriented linear low‐density polyethylene (LLDPE) is evaluated by the Essential Work of Fracture (EWF) concept, with a special setup of CCD camera to monitor the process of deformation. Allowing for the molecular orientation, flow‐oriented sample, prepared via melt extrusion drawing, is stretched parallel (oriented‐0°) and perpendicular (oriented‐90°) to its original melt extrusion drawing direction, respectively. The obtained values of specific EFW w_e are 34.6, 10.2, and 4.2 N/mm for the oriented‐0°, isotropic and oriented‐90° sample, respectively. With knowledge of intrinsic deformation parameters deduced from uniaxial tensile tests, moreover, a relationship between specific EFW w_e the ratio of true yield stress to strain hardening modulus σ_ty/G is well established. It means that the fracture toughness of polyethylene is determined by both crystalline and amorphous parts, rather than by one of them. Moreover, the true yield stress seems to be nondecisive factors determining the fracture toughness of polyethylene. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2880–2887, 2006     

Morphologies and crystalline forms of polyvinylidene fluoride membranes prepared in different diluents by thermally induced phase separation

We have studied the morphologies and crystalline forms of polyvinylidene fluoride (PVDF) membranes separately prepared in four different diluents bearing >C?O groups, namely 1,2‐propylene glycol carbonate (PGC), dimethyl phthalate (DMP), diphenyl ketone (DPK), and dibutyl phthalate (DBP), by the thermally induced phase separation (TIPS) method. The permittivities of the diluents and PVDF were measured to compare the different PVDF–diluent systems. The results showed the permittivity of PGC to be much greater than that of PVDF, and those of DMP and DBP to be lower than that of PVDF. The permittivity difference between DPK and PVDF was not apparent above 120 °C. On cooling mixtures with a PVDF concentration of 10 wt %, PVDF crystallization was observed in the PVDF–DMP, PVDF–DBP, and PVDF–PGC systems, while liquid–liquid phase separation occurred in the PVDF–DPK system. A cross‐section of the PVDF–PGC membrane presented smooth PVDF particles in the β‐phase crystalline form. Those of the PVDF–DMP and PVDF–DBP membranes presented PVDF particles consisting of a fibrillar network in the α‐phase. The PVDF–DPK membrane preferentially adopted an α‐phase bicontinuous channel structure. When the concentration of PVDF was 60 wt %, the cross‐sections of the above four membranes revealed PVDF polyhedra, among which the PVDF–DMP, PVDF–DBP, and PVDF–DPK membranes retained the α‐phase crystalline form, and the diffraction peak of the α‐phase became visible in the X‐ray diffraction (XRD) spectrum of the PVDF–PGC membrane. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Conformational changes and phase transformation mechanisms in PVDF solution‐cast films

The supramolecular crystal structure in poly(vinylidene fluoride) (PVDF) solution‐cast films is studied through changing crystallization conditions in two solvents of different structures and polarities. The crystalline‐state chain conformations of isothermally solution‐crystallized PVDF in N, N‐dimethylacetamide (DMAc), and cyclohexanone are studied through the specific FTIR absorption bands of α, β, and γ phase crystals. There are no changes in the FTIR spectra of cyclohexanone solution‐crystallized films in the temperature range of 50–120 °C. In the case of DMAc solution‐crystallized films, low temperature crystallization mainly results in formation of trans states (β and γ phases), whereas at higher temperatures gauche states become more populated (α phase). This is due to the variations in solvent polarity and ability to induce a specific conformation in PVDF chains, through the changes in chain coil dimensions. This indicates that in spite of cyclohexanone solutions, the intermolecular interactions between PVDF and DMAc are temperature‐sensitive and more important in stabilizing conformations of PVDF in crystalline phase than temperature dependence of PVDF chain end‐to‐end distance <r²>. The high‐resolution ¹⁹F NMR spectroscopy also showed little displacement in PVDF characteristic chemical shifts probably due to changes in PVDF chain conformation resulting from temperature variations. Upon uniaxial stretching of the prepared films under certain conditions, contribution of trans state becomes more prominent, especially for the originally higher α phase‐containing films. Due to formation of some kink bands during film stretching and phase transformation, α phase absorption bands are still present in infrared spectra. Besides, uniaxial stretching greatly enhances piezoelectric properties of the films, maybe due to formation of oriented β phase crystals, which are of more uniform distribution of dipole moments. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3487–3495, 2004     

Computational analysis of bending strain in single chains of β‐PVDF

Hartree–Fock calculations on 20 carbon atom chains of β‐phase poly(vinylidene fluoride) (PVDF) were done as a function of bending strain. The results can be modeled in terms of a classical energy versus strain curve resulting in a pseudomodulus (310 GPa) comparable to the Young's modulus calculated for stretching along carbon atom chain (199 GPa). The model also shows that the minimum energy state of a single chain of the polymer is not linear in the all‐trans geometry and that a significant strain energy is stored in natural thin films. This suggests that energy can be captured from bending motions in β‐PVDF. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1493–1495, 2011     

Rheological properties of linear and crosslinked polymer blends: Relation between crosslink density and enhancement of elongational viscosity

Strain‐hardening behavior in the elongational viscosity of binary blends composed of a linear polymer and a crosslinked polymer, in which the molecular chains of the linear polymer were incorporated into the network chains of the crosslinked polymer, was studied. Blending the crosslinked polymer characterized as the gel just beyond the sol–gel transition point greatly enhanced the strain‐hardening behavior in the elongational viscosity, even though the amount of the crosslinked polymer was only 0.3 wt %. However, the crosslinked polymer, which was far beyond or below the sol–gel transition point, had little influence on the elongational viscosity as well as the shear viscosity. The stretching of the chain sections between the crosslink points was responsible for the strain‐hardening behavior. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 228–235, 2001     

Matrix‐polymer‐functionalized multiwalled carbon nanotubes as a highly efficient toughening agent for matrix polymers

Matrix‐polymer‐functionalized multiwalled carbon nanotubes (MWCNTs) are demonstrated as a highly efficient toughening agent for matrix polymers. With poly(vinylidene fluoride) (PVDF) as the matrix polymer, the PVDF/MWCNT‐PVDF nanocomposite films show high toughness. With a small load amount of MWCNT‐PVDF (0.07 wt %), the nanocomposite film shows a yield point and a constant‐stress extension region in stress–strain tests, compared with the typical low‐extensibility feature of neat PVDF film. The PVDF/MWCNT‐PVDF‐0.7 film exhibits a 180‐fold increase of toughness and about 38‐fold increase in strain at break compared with neat PVDF film. This toughening effect is attributed to (a) homogeneous dispersion of MWCNT‐PVDF in PVDF, (b) the high efficiency of load‐transfer across MWCNT/PVDF interface, and (c) the long length of the MWCNTs. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Preferential formation of electroactive crystalline phases in poly(vinylidene fluoride)/organically modified silicate nanocomposites

The role of organically modified silicate (OMS), Lucentite STN on the formation of β‐crystalline phase of poly(vinylidene fluoride) (PVDF) is investigated in the present study. The OMS was solution blended with PVDF and cast on glass slide to form PVDF‐OMS nanocomposites. Solution cast samples were subjected to various thermal treatments including annealing (AC‐AN), melt‐quenching followed by annealing (MQ‐AN), and melt‐slow cooling (MSC). Fourier‐transform infrared spectroscopy (FT‐IR), wide angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC) were used to investigate the crystalline structure of thermally treated samples. As a special effort, the combination of in situ thermal FT‐IR, WAXD, and DSC studies was utilized to clearly assess the thermal properties. FT‐IR and WAXD results of MQ‐AN samples revealed the presence of β‐phase of PVDF. Ion‐dipole interaction between the exfoliated clay nanolayers and PVDF was considered as a main factor for the formation of β‐phase. Melt‐crystallization temperature and subsequent melting point were enhanced by the addition of OMS. Solid β‐ to γ‐crystal phase transition was observed from in situ FT‐IR and WAXD curves when the representative MQ‐AN sample was subjected to thermal scanning. Upon heating, β‐phase was found to disappear through transformation to the thermodynamically stable γ‐phase rather than melting directly. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2173–2187, 2008     

Enhanced electrical properties of highly oriented poly(vinylidene fluoride) films prepared by solid‐state coextrusion

Oriented poly(vinylidene fluoride) (PVDF) films with β‐form crystals have been commonly prepared by cold drawing of a melt‐quenched film consisting of α‐form crystals. In this study, we have successfully produced highly oriented PVDF thin films (20 µm thick) with β‐crystals and a high crystallinity (55–76%), by solid‐state coextrusion of a gel film to eight times the original length at an established optimum extrusion temperature of 160°C, some 10°C below the melting temperature. The resultant drawn films had a highly oriented (orientation function f_c = 0.993) fibrous structure, showing high mechanical properties of an extensional elastic modulus of 8.3 GPa and tensile strength of 0.84 GPa, along the draw direction. Such highly oriented and crystalline films exhibited excellent ferroelectric and piezoelectric properties. The square hysteresis loop was significantly sharper than that of a conventional sample. The sharp switching transient yielded the remnant polarization P_r of 90 mC/m², and the electromechanical coupling factor k_t was 0.24 at room temperature. These values are about 1.5 times greater than those of a conventional β‐PVDF film. Thus, solid‐state coextrusion near the melting point was found to be a useful technique for the preparation of highly oriented and highly crystalline β‐PVDF films with superior mechanical and electrical properties. The morphology of the extrudate relevant to such properties is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2549–2556, 1999     

Rheo-optical FT-IR Spectroscopy of LLDPE: Effect of Comonomer and Composite Materials

Summary: In order to further evaluate the potential of FT-IR spectroscopic investigations on molecular processes during tensile testing experiments, the behavior of monolayer LLDPE films, made with ethylene-butene and ethylene-octene copolymers, was studied. Additionally, multilayer LLDPE films based on the same C4 and C8 copolymers were investigated. The stress-strain data obtained from the monolayer films indicate differences in the strain hardening region. It seems that the film samples PE 469-30-2 (C4-gas phase process) and PE 469-30-5 (C8 solution process) behave similarly whereas the strain hardening for the PE 469-30-3 (C4 solution process) requires lower stress values. The orientation function changes during the stretching of the films indicating that unfolding of the polymer chains occurs at lower strain for PE 469-30-5 (C8) than in the C4 materials. In the multilayer systems the Primplast 44 material (C8) shows a lower tendency for reorientation in the strain hardening region than the Coex 82 (C4) material. In this region of the stress-strain curve the lamellar structure is already transformed into the fibrillar arrangement. Regarding the orientation behavior of the material above 200% strain, a small increase in f_b was observed, which led to a decrease of f_c. In the octene product possibly the bulky side chains influence the unfolding significantly, producing a higher resistance to unfolding and alignment along the stretching direction. In part, this is potentially caused by the more perfect lamellae in the octene copolymer, which do not include the side chains, while the butene copolymer may have weaker lamellae because they contain a fraction of the side chains which create defects. Consequently, the octene copolymer requires higher stress values to be stretched and finally results in a lower stretchability of this material, as observed on an industrial scale during pallet wrapping tests. Based on the ratio of the structural absorbance parameters of the signals at 729 and 719 cm⁻¹ changes in the crystallinity were studied. For the continuous stretching experiment, no monoclinic phase was detected even after Fourier self-deconvolution and peak fitting approaches. Literature data, however, describe that this crystalline transformation takes place as a result of mechanical deformation. Therefore, stepwise stretching experiments which allow an improvement of the spectral resolution to 1 cm⁻¹ were carried out. In the deconvoluted spectra the monoclinic, orthorhombic and amorphous LLDPE modifications could be assigned. Ultimate stretchability and stretching force of the films, both monolayer and multilayer, was well correlated to the development of crystalline orientation in the films upon stretching. Other mechanical properties like Elmendorf tear and dart impact can also be better understood with these results.     

Microporous membranes obtained from polypropylene blend films by stretching

Blends of two linear polypropylenes (PP, having different molecular weights) were prepared to develop microporous membranes through melt extrusion followed by stretching. The role of high molecular weight chains on the row-nucleated lamellar crystallization was investigated. The orientation of crystalline and amorphous phases was measured by wide angle X-ray diffraction (WAXD) and Fourier transform infrared (FTIR). Long period spacing was obtained using small angle X-ray scattering (SAXS). The effects of annealing temperature and applied elongation during annealing on the crystallinity of the films were studied using differential scanning calorimetry (DSC). It was found that annealing at 140 °C contributed significantly to the perfection of the crystalline phase. Scanning electron microscopy (SEM) images of the membrane surface showed more pore density and uniform pore size as the amount of high molecular weight component increased. The addition of the high M_w PP improved the water vapor transmission rate (WVTR) of the membranes, indicating increased interconnectivity of the pores, which was also confirmed from cross-section SEM micrographs of the membranes. The surface area and pore dimensions of the microporous membranes were measured using the BET nitrogen absorption technique and mercury porosimetry, respectively. The influences of temperature and amount of stretching during cold and hot stretching on WVTR were also explored. Tensile properties in the machine and transverse directions (MD and TD, respectively) as well as puncture resistance in the normal direction (ND) were evaluated. As the high M_w PP was added, a slight reduction in the mechanical properties along MD and TD and no changes in ND were observed.     

Phase transformation and enhancement of toughness in polyvinylidene fluoride by onium salts

We study the effect of onium salts (benzyl triphenyl phosphonium chloride, BTPC; tetrabutyl ammonium perchlorate, TAP) on the crystallization of polyvinylidene fluoride (PVDF) from a melt. The β phase of PVDF crystals is polar and has excellent piezoelectric properties, in contrast to the nonpolar α phase. Processing of PVDF results in the formation of predominantly α‐phase crystals. Different amounts of the onium salts were melt‐mixed into PVDF using a micro‐compounder. PVDF containing about 0.5 wt % of BTPC is found to have predominantly β‐phase crystals in compression molded PVDF films, with an increase in the melting temperature by about 7 °C. A significant increase in the toughness of PVDF is obtained by the addition of BTPC. Polarizing microscopy indicates that the onium salts act as nucleating agents and result in significant reduction in spherulite size. Similar results were observed for samples prepared with TAP. The results of the study indicate a facile method for producing β‐phase PVDF films. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1339–1344, 2011     

Ferroelectric poly(vinylidene fluoride) PVDF films derived from the solutions with retainable water and controlled water loss

To obtain β‐phase dominant ferroelectric poly(vinylidene fluoride) (PVDF) homopolymer thin films on aluminum‐coated silicon substrates, the retaining and loss of water were manipulated by introducing several hydrated and hygroscopic chemicals in the precursor solutions, including aluminum nitrate nonahydrate, aluminum chloride hexahydrate, chromium nitrate nonahydrate, tetra‐n‐butylammonium chloride, and one hygroscopic but nonhydrated chemical, ammonium acetate. Their ability of retaining water during the thermal annealing of the films and the relationship between water retaining and the effects on promoting the β phase were investigated. The results showed an ideal scenario was that the added hydrated salts should be able to retain substantial amount of water during the PVDF crystallization to effectively promote the β phase but completely dehydrate or decompose at the further elevated annealing temperature in order to obtain β‐phase dominant PVDF film without substantially incorporating water and deteriorating the electrical properties. As one of the hydrated chemicals well satisfying the above requirements, Al(NO₃)₃·9H₂O, of different amounts was introduced to the PVDF precursor solutions and the optimal resulting β‐phase dominant ferroelectric PVDF thin films exhibited smooth morphology, low dielectric loss, high remnant polarization of 89 mC/m², and large effective piezoelectric coefficient d₃₃ of ?14.5 pm/V (under the clamping of the substrate). © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2410–2418, 2009     

Thermal properties and structure of electrospun blends of PVDF with a fluorinated copolymer

We report the structure and thermal properties of blends comprising poly(vinylidene fluoride) (PVDF) and a random fluorinated copolymer (FCP) of poly(methyl methacrylate)‐random‐1H,1H,2H,2H‐perfluorodecyl methacrylate, promising membrane materials for oil–water separation. The roles of processing method and copolymer content on structure and properties were studied for fibrous membranes and films with varying compositions. Bead‐free, nonwoven fibrous membranes were obtained by electrospinning. Fiber diameters ranged from 0.4 to 1.9 μm, and thinner fibers were obtained for PVDF content >80%. As copolymer content increased, degree of crystallinity and onset of degradation for each blend decreased. Processing conditions have a greater impact on the crystallographic phase of PVDF than copolymer content. Fibers have polar beta phase; solution‐cast films contain gamma and beta phase; and melt crystallized films form alpha phase. Kwei's model was used to model the glass transition temperatures of the blends. Addition of FCP increases hydrophobicity of the electrospun membranes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 312–322