Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

Epoxy‐functionalized,low‐glass‐transition‐temperature latex. II. Interdiffusion versus crosslinking in the presence of a diamine

This article describes the results of experiments examining the competition between the polymer diffusion rate and the crosslinking rate in low‐glass‐transition‐temperature, epoxy‐containing latex films in the presence of a diamine. We examined films formed from donor‐ and acceptor‐labeled poly(butyl acrylate‐co‐methyl methacrylate‐co‐glycidyl methacrylate) copolymer latex and studied the influence of several parameters on the growth rate of gel content and the rate of polymer diffusion. These factors include the molecular weight of the latex polymer, the presence or absence of a diamine crosslinking agent, and the cure protocol. The results were compared to the predictions of a recent theory of the competition between crosslinking and polymer diffusion across interfaces. In the initially formed films, polymer diffusion occurs more rapidly than the chemical reaction rate. Therefore, these films fall into the fast‐diffusion category of this model. In our system (unlike in the model), the latex polymer has a broad distribution of molecular weights and a distribution of diffusivities. The shortest chains contribute to the early time diffusion that we measure. At later stages of our experiment, slower diffusing species contribute to the signal that we measure. The diffusion time decreases substantially, and we observe a crossover to a regime in which the chemical reaction dominates. The increases in chain branching and gel formation bring polymer diffusion to a halt. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4098–4116, 2002     

Synthesis and characteristics of poly(methyl methacrylate‐co‐methacrylic acid)/poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive semi‐hollow latex particles and their application to drug carriers

In this work, the poly(methyl methacrylate‐co‐methacrylic acid)/poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite semi‐hollow latex particles was synthesized by three processes. The first process was to synthesize the poly(methyl methacrylate‐co‐methacrylic acid) (poly (MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. The second process was to polymerize methacrylic acid (MAA), N‐isopropylacrylamide (NIPAAm), and crosslinking agent, N,N′‐methylenebisacrylamide, in the presence of poly(MMA‐MAA) latex particles to form the linear poly(methyl methacrylate‐co‐methacrylic acid)/crosslinking poly(methacrylic acid‐co‐N‐isopropylacrylamide) (poly(MMA‐MAA)/poly(MAA‐NIPAAm)) core–shell latex particles with solid structure. In the third process, part of the linear poly(MMA‐MAA) core of core–shell latex particles was dissolved by ammonia to form the poly(MMA‐MAA)/poly(MAA‐NIPAAm) thermosensitive semi‐hollow latex particles. The morphologies of the semi‐hollow latex particles show that there is a hollow zone between the linear poly(MMA‐MAA) core and the crosslinked poly(MAA‐NIPAAm) shell. The crosslinking agent and shell composition significantly influenced the lower critical solution temperature of poly(MMA‐MAA)/poly(MAA‐NIPAAm) semi‐hollow latex particles. Besides, the poly(MMA‐MAA)/poly(MAA‐NIPAAm) thermosensitive semi‐hollow latex particles were used as carriers to load with the model drug, caffeine. The processes of caffeine loaded into the semi‐hollow latex particles appeared four situations, which was different from that of solid latex particles. In addition, the phenomenon of caffeine released from the semi‐hollow latex particles was obviously different from that of solid latex particles. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3441–3451     

Synthesis and antibacterial activities of water‐soluble methacrylate polymers containing quaternary ammonium compounds

New water‐soluble methacrylate polymers with pendant quaternary ammonium (QA) groups were synthesized and used as antibacterial materials. The polymers with pendant QA groups were obtained by the reaction of the alkyl halide groups of a previously synthesized functional methacrylate homopolymer with various tertiary alkyl amines containing 12‐, 14‐, or 16‐carbon alkyl chains. The structures of the functional polymer and the polymers with QA groups were confirmed with Fourier transform infrared and ¹H and ¹³C NMR. The degree of conversion of alkyl halides to QA sites in each polymer was determined by ¹H NMR to be over 90% in all cases. The number‐average molecular weight and polydispersity of the functional polymer were determined by size exclusion chromatography to be 32,500 g/mol and 2.25, respectively. All polymers were thermally stable up to 180 °C according to thermogravimetric analysis. The antibacterial activities of the polymers with pendant QA groups against Staphylococcus aureus and Escherichia coli were determined with broth‐dilution and spread‐plate methods. All the polymers showed excellent antibacterial activities in the range of 32–256 μg/mL. The antibacterial activity against S. aureus increased with an increase in the alkyl chain length for the ammonium groups, whereas the antibacterial activity against E. coli decreased with increasing alkyl chain length. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5965–5973, 2006     

Synthesis and characteristics of poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles and their application as drug carriers

In this work, the poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles was synthesized by a three‐step reaction. The first step was to synthesize the poly(methyl methacrylate‐co‐methacrylic acid) (poly(MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. The second step was to polymerize methacrylic acid (MAA), N‐isopropylacrylamide (NIPAAm), and N,N′‐methylenebisacrylamide in the presence of poly(MMA‐MAA) latex particles to form the linear poly(methyl methacrylate‐co‐methacrylic acid)/crosslinking poly(methacrylic acid‐co‐N‐isopropylacrylamide) (poly(MMA‐MAA)/poly(MAA‐NIPAAm)) core–shell latex particles. In the third step, the core–shell latex particles were heated in the presence of ammonia solution to form the crosslinking poly(MAA‐NIPAAm) thermosensitive hollow latex particles. The morphologies of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were observed. The influences of crosslinking agent and shell composition on the lower critical solution temperature of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were, respectively, studied. Besides, the poly(MAA‐NIPAAm) thermosensitive hollow latex particles were used as carriers to load with the model drug, caffeine. The effect of various variables on the amount of caffeine loading and the efficiency of caffeine release was investigated. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5203–5214     

A rheological and spectroscopic study on the kinetics of self‐healing in a single‐component diels–alder copolymer and its underlying chemical reaction

In this work, pendant groups with both furan and maleimide moieties were incorporated into a polymethacrylate copolymer with lauryl methacrylate as comonomer to yield a one‐system Diels–Alder (DA) polymer. A combined Fourier transform infrared (FTIR) spectroscopy and rheological study was performed to quantify the extent of the reversible DA reaction and the resulting changes in mechanical properties of the polymer. The kinetics of the retro‐Diels–Alder (rDA) reaction was studied at different temperatures to determine an enthalpy of activation. Control polymers with only one functional moiety, that is, the furan or maleimide, were also synthesized to study the differences in viscoelastic behavior and the absence of self‐healing. Microscratch tests were performed to obtain information about the disappearance of well‐defined intentional surface scratches under different healing conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1669–1675     

Large electro‐optic activity and enhanced temporal stability of methacrylate‐based crosslinking hyperbranched nonlinear optical polymer

A methacrylate‐based crosslinking hyperbranced polymers have been synthesized through initiator‐fragment incorporation radical polymerization and used for the temperature stable electro‐optic (EO) polymer application. This polymer consists of methyl methacrylate, 2‐metacryloxyethyl isocyanate, and ethylene glycol dimethacrylate (EGDMA) monomers. The use of EGDMA as a bifunctional unit resulted in the solvent‐soluble crosslinking hyperbranched chain, so that the EO polymer enhanced glass transition temperatures. A phenyl vinylene thiophene vinylene bridge nonlinear optical chromophore was attached to the polymer backbone as the side‐chain by a post‐functionalization reaction. The loading concentration of the chromophore was varied between 30 and 50 wt % by simply changing the mixing ratio of the precursor polymer to the chromophore. The synthesized EO polymers produced optical quality films with a light propagation loss of 0.61 dB/cm in a slab waveguide at 1.31 μm. The electrically poled film had an EO coefficient (r₃₃) of 139 pm/V at 1.31 μm. The EO crosslinking hyperbranced polymer had a high‐glass transition temperature of 170 °C, and exhibited excellent temporal stability of the EO activity at 85 °C for 500 h. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Novel silver‐loaded semi‐interpenetrating polymer network gel films with antibacterial activity

Novel semi‐interpenetrating polymer networks (SIPNs) based on segmented polyurethane‐urea and poly(N‐isopropylacrylamide‐co‐acrylic acid‐co‐butylmethacrylate) (poly(NIPAM‐co‐AA‐BMA)) were synthesized for the fabrication of silver nanoparticles (AgNPs) in the SIPN system that could be useful for wound dressing applications. The obtained SIPN films, after neutralization, showed high swelling in aqueous environments and good mechanical properties in both dry and hydrated states. Analysis of the dried SIPN films by differential scanning calorimetry and dynamic viscoelastic measurements revealed the presence of crosslinked copolymers as well as homopolymers in the SIPN system. The neutralized swollen SIPN film coordinated with the silver ions (Ag⁺) that were incorporated into it. AgNPs were subsequently formed by the reduction of Ag⁺. The formation of AgNPs was characterized by UV‐visible spectroscopy, atomic force microscopy, wide‐angle X‐ray diffraction, and thermogravimetric analysis (TGA). Bactericidal activity tests revealed a distinct zone of microbial inhibition within and around the silver‐doped SIPN films. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4950–4962, 2009     

Synthesis and antibacterial activity of surface‐coated catechol‐conjugated polymer with silver nanoparticles on versatile substrate

In the present study, 2‐chloro‐3′,4′‐dihydroxyacetophenone (CCDP), a catechol derivative, was quaternized with poly(propylene oxide)‐g‐poly(dimethylaminoethyl methacrylate) (PPO‐g‐PDMA, PgP) to prepare surface coatings for various substrates. The surfaces of noble metals, oxides, and synthetic polymers were coated by immersion in an aqueous solution of CCDP quaternized with PgP (C‐PgP). The catechol functional groups that remained on the surface were used for deposition of Ag nanoparticles (AgNPs) on the coated surface, to provide a water‐resistant antibacterial polymer with long‐term antimicrobial activity. X‐ray photoelectron spectroscopy confirmed deposition of C‐PgP and AgNPs on the surface coated with the antibacterial polymer. Surface‐immobilized C‐PgP/AgNPs showed outstanding antibacterial activities against Staphylococcus aureus, a Gram‐positive bacterium, and Escherichia coli, a Gram‐negative bacterium. C‐PgP/AgNPs can be applied to a variety of substrates and can therefore be used as antibacterial materials in various fields. Copyright © 2016 John Wiley & Sons, Ltd.     

Influence of polymer particle size on the percolation threshold of electrically conductive latex‐based composites

Monodispersed copolymer emulsions, each with a different polymer particle size, were used to investigate the effect of particle size on the electrical and thermomechanical properties of carbon black (CB)‐filled segregated network composites. These emulsions were synthesized with equal moles of methyl methacrylate and butyl acrylate, with latex particle size ranging from 83 to 771 nm. The electrical percolation threshold was found to decrease from 2.7 to 1.1 vol % CB as the latex particle size was increased. Microstructural images reveal diminished latex coalescence, and improved CB segregation, with increasing latex particle size. In general, coalescence is shown to increase for all systems with increasing CB concentration. Furthermore, all systems exhibited a similar maximum electrical conductivity plateau of 0.7 S cm^?1, albeit at lower concentration for larger latex particle size. This ability to tailor percolation threshold with latex particle size provides an important tool for manipulating electrical and mechanical properties of polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1547–1554, 2011     

Terpene based sustainable methacrylate copolymer series by emulsion polymerization: Synthesis and structure‐property relationship

This work demonstrates the fabrication of terpene based sustainable methacrylate polymers by an environmentally benign emulsion polymerization method. The polymerization reaction has been found to be influenced by the side chain length of the methacrylate(s), which has been quantitatively calculated from the density functional theory. Apart from the analysis of the copolymer microstructure, various properties of the synthesized polymers have been studied and correlated with the structure of the methacrylate(s). The sub‐ambient glass transition temperature indicates rubbery nature of the synthesized copolymers. While the presence of residual unsaturations from the terpene moiety could act as an additional crosslinking site, the methacrylate group may facilitate the dispersion of polar additives. The completely new class of terpene‐based sustainable rubbery methacrylate polymers is thus envisaged as promising materials for polymer and allied industries. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2639–2649     

Synthesis,characterization, and stability of carbodiimide groups in carbodiimide‐functionalized latex dispersions and films

Cyclohexylcarbodiimidoethyl methacrylate (CCEMA) and t‐butylcarbodiimidoethyl methacrylate (t‐BCEMA) were prepared in a two‐step synthesis. These monomers were then used to prepare carbodiimide‐functionalized PBMA and PEHMA latex particles, employing two‐stage emulsion polymerization, with the carbodiimide–methacrylate monomers being introduced only in the second stage under monomer‐starved conditions. During emulsion polymerization, the carbodiimide moiety ( NCN ) was found to be unstable at pH 4, but stable when the pH of the dispersion was increased to 8, using NaHCO₃ as the buffer. Survival of  NCN group against hydrolysis during the polymerization, and during storage in the dispersion, was enhanced by using EHMA as the comonomer (more hydrophobic) and the t‐butyl carbodiimide derivative. The t‐butyl group provides more steric hindrance to the hydrolysis reaction. A decrease in the reaction temperature from 80°C to 60°C was also found to increase the extent of  NCN group incorporation during emulsion polymerization. Under ideal conditions, more than 98% of the  NCN groups in the monomer feed are successfully incorporated into the latex. When these latex particles are mixed with a  COOH containing latex and allowed to dry, polymer diffusion leading to crosslinking occurs. Films annealed at 60°C reach a gel content of 60% in 10 h. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 855–869, 2000     

Synthesis and characteristics of poly(N‐isopropylacrylamide‐co‐methacrylic acid)/Fe3O4 thermosensitive magnetic composite hollow latex particles

In this study, the poly(NIPAAm–MAA)/Fe₃O₄ hollow latex particles were synthesized by three steps. The first step was to synthesize the poly(methyl methacrylate‐co‐methylacrylate acid) (poly(MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. Following the first step, the second step was to polymerize N‐isopropylacrylamide (NIPAAm), MAA, and crosslinking agent (N,N'‐methylene‐bisacrylamide (MBA)) in the presence of poly(MMA‐MAA) latex particles to form the linear poly(MMA‐MAA)/crosslinking poly (NIPAAm‐MAA) core‐shell latex particles. After the previous processes, the core‐shell latex particles were heated in the presence of NH₄OH to dissolve the linear poly(MMA‐MAA) core in order to form the poly(NIPAAm‐MAA) hollow latex particles. In the third step, Fe²⁺ and Fe³⁺ ions were introduced to bond with the ? COOH groups of MAA segments in the poly(NIPAAm‐MAA) hollow polymer latex particles. Further by a reaction with NH₄OH and then Fe₃O₄ nanoparticles were generated in situ and the poly(NIPAAm‐MAA)/Fe₃O₄ magnetic composite hollow latex particles were formed. The concentrations of MAA, crosslinking agent (N,N'‐methylene bisacrylamide), and Fe₃O₄ nanoparticles were important factors to influence the morphology of hollow latex particles and lower critical solution temperature of poly(NIPAAm–MAA)/Fe₃O₄ magnetic composite hollow latex particles. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Development and analysis of cellulose nanocomposite films with in situ generated silver nanoparticles using tamarind nut powder as a reducing agent

Cellulose/Tamarind nut powder (TNP)/Silver nanoparticles (AgNPs) nanocomposites were prepared by in situ generation of AgNPs using regeneration method, followed by solution casting method. In this, TNP was used as a reducing agent. These nanocomposites were characterized using FT-IR spectroscopy, XRD and SEM and studied their mechanical properties and antibacterial activity for medical and packing applications. The FT-IR spectral studies revealed the involvement of functional groups – Polyphenols, Flavonoids and –OH in the process of reducing the metal salts into metal nanoparticles. These nanocomposites showed good antibacterial activity against five bacteria. Improved mechanical properties with good antibacterial activities make these composites suitable for medical, food and packaging applications.     

Hydrophilic nanocomposites based on polyurethane/poly(2‐hydroxyethyl methacrylate) semi‐IPNs and modified/unmodified nanosilica for biomedical applications

Nanocomposites based on sequential semi‐interpenetrating polymer network (semi‐IPN) of cross‐linked polyurethane and linear poly(2‐hydroxyethyl methacrylate) with 0.25 and 3 wt % of nanosilica filler were prepared and investigated. The unmodified silica, carboxyl‐modified, and amino‐modified silica were used in an attempt to control the microphase separation of the polymer matrix by polymer–filler interactions. A variety of experimental techniques were used to study morphology, thermal transitions, mechanical properties, and polymer dynamics of the nanocomposites. Special attention was paid to the investigation of the hydration properties of the nanocomposites in the perspective of biomedical applications. The results show that the good hydration properties of the semi‐IPN matrix are preserved in the nanocomposites. Effects of water on polymer dynamics were found to be particularly pronounced for the secondary β_sw,_PHEMA and the β_PU relaxations, in agreement with interpretations in terms of hydrogen bonding interactions with specific groups in the structure of the two polymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 397–408     

Photo‐induced thiol‐ene polysulfide‐crosslinked materials with tunable thermal and mechanical properties

Photo‐induced thiol‐ene crosslinked polymeric networks have been extensively explored in constructing a variety of new materials with enhanced mechanical properties for optical, biomedical, and sensing applications. Toward the broad applications, however, tunable mechanical properties are greatly desired. Here, an effective approach utilizing high‐molecular‐weight methacrylate copolymers having pendant thiol and vinyl groups (MCPsh and MCPenes) to modulate thermal and mechanical properties of photo‐induced thiol‐ene crosslinked materials is reported. The MCP copolymers are synthesized by an industrially friendly polymerization method, followed by post‐modification including either a facile coupling reaction or reductive cleavage. Upon UV irradiation, thiol‐ene reactive blends of MCPsh and MCPenes yield highly crosslinked materials through the formation of flexible sulfide linkages. These polysulfide‐crosslinked materials based on rigid MCP backbones exhibit enhanced mechanical properties. Further, their thermal and mechanical properties are tuned by modulating monomer compositions of MCPs as well as varying numbers of pendant SH or vinyl groups (i.e., extent of crosslinking densities). This approach is versatile and effective for development of high performance polymeric materials. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3060–3068     

Crosslinking‐induced morphology change of latex nanoparticles: A study of RAFT‐mediated polymerization in aqueous dispersed media using amphiphilic double‐brush copolymers as reactive surfactants

Amphiphilic double‐brush copolymers (DBCs) with each graft site quantitatively carrying both a hydrophilic poly(ethylene oxide) (PEO) graft and a hydrophobic polystyrene (PSt) graft are synthesized by sequential reversible addition‐fragmentation chain transfer (RAFT) polymerization and ring‐opening metathesis polymerization (ROMP). These DBCs are used as both surfactants and polyfunctional RAFT agents in the radical polymerization of St in aqueous dispersed media. Miniemulsions with narrowly dispersed St‐based nanodroplets are readily obtained after ultrasonication of the reaction mixtures. Without the presence of crosslinker, chain‐extension polymerization of St from the DBCs yields well‐defined polymeric latexes with narrow size distributions. However, with the presence of divinylbenzene (DVB) as the crosslinker, vesicular polymeric nanoparticles are formed as the major product. Such crosslinking‐induced change in morphology of the resulting latex nanomaterials may be ascribed to the increase of interfacial curvature in the heterophase systems during crosslinking polymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3250–3259     

Dispersion polymerization using hydroxy‐functional macroazoinitiators as an inistab

Hydroxy‐functional macroazoinitiators with central azo unit have been synthesized by atom transfer radical polymerization of 2‐hydroxyethyl methacrylate or 2‐hydroxypropyl methacrylate in methanol. The mean degrees of polymerization of the polymer chains beside the azo group were fixed at 30 and 60. Proton nuclear magnetic resonance (¹H NMR) and gel permeation chromatography were used to characterize the macroazoinitiators in terms of their chemical structure, molecular weight, and polydispersity, respectively. Dispersion polymerizations of styrene using the hydroxy‐functional macroazoinitiators as an inistab (initiator + colloidal stabilizer) in 2‐propanol or 2‐propanol/water media resulted in submicrometer‐sized polystyrene latex particles with hydroxy‐functional polymer hair. Electron microscopies, Fourier transform infrared spectrometer, thin layer chromatography, and ¹H NMR were used to characterize the particles in terms of their morphologies, particle sizes, and their distributions and chemical compositions. The synthesized particles behaved as an effective particulate emulsifier for the stabilization of oil‐in‐water emulsions. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

A new green method for the synthesis of silver nanoparticles and their antibacterial activities against gram‐positive and gram‐negative bacteria

This study aims to evaluate the capability of Ageratum conyzoides and Mikania micrantha extracts to synthesize silver nanoparticles (AgNPs) and their antibacterial capability against gram‐positive and gram‐negative bacteria. Several properties of the synthesized AgNPs, including plasmonic, biomolecule bonding, shape, size, and antibacterial, were investigated. Ultraviolet–visible (UV–vis) spectroscopy was employed for characterizing their plasmonic properties. Functional groups on the produced AgNPs were investigated by Fourier‐transform infrared (FT‐IR) spectroscopy. The size and shape of the AgNPs were identified using the field‐emission scanning electron microscopy (FESEM). Inhibition zone measurement was carried out for evaluating the antibacterial capability. This study showed that the extracts of A. conyzoides and M. micrantha were able reducing agents as evidenced by the formation of the spherical AgNPs. UV–vis spectroscopy, FT‐IR spectroscopy, and FESEM confirmed the physicochemical characteristics of AgNPs. AgNPs that were synthesized using M. micrantha were slightly smaller than those produced using A. conyzoides. In general, the present work establishes that the synthesized AgNPs have antibacterial capability depending on their size and synthesis procedure.     

Preparation and clinical application of immunomagnetic latex

Magnetic poly(methyl methacrylate) (PMMA)/poly(methyl methacrylate‐co‐methacrylic acid) [P(MMA–MAA)] composite polymer latices were synthesized by two‐stage soapless emulsion polymerization in the presence of magnetite (Fe₃O₄) ferrofluids. Different types and concentrations of fatty acids were reacted with the Fe₃O₄ particles, which were prepared by the coprecipitation of Fe(II) and Fe(III) salts to obtain stable Fe₃O₄ ferrofluids. The Fe₃O₄/polymer particles were monodisperse, and the composite polymer particle size was approximately 100 nm. The morphology of the magnetic composite polymer latex particles was a core–shell structure. The core was PMMA encapsulating Fe₃O₄ particles, and the shell was the P(MMA–MAA) copolymer. The carboxylic acid functional groups (COOH) of methacrylic acid (MAA) were mostly distributed on the surface of the composite polymer latex particles. Antibodies (anti‐human immunoglobulin G) were then chemically bound with COOH groups onto the surface of the magnetic core–shell composite latices through the medium of carbodiimide to form the antibody‐coated magnetic latices (magnetic immunolatices). The MAA shell composition of the composite latex could be adjusted to control the number of COOH groups and thus the number of antibody molecules on the magnetic composite latex particles. With a magnetic sorting device, the magnetic immunolatices derived from the magnetic PMMA/P(MMA–MAA) core–shell composite polymer latex performed well in cell‐separation experiments based on the antigen–antibody reaction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1342–1356, 2005