Grafting of Polymers from Carbon Fiber. Anionic Graft Polymerization of Vinyl Monomers Initiated by Metallized Aromatic Rings on Carbon Fiber

The anionic graft polymerization of vinyl monomers onto carbon fiber initiated by metallized carbon fiber was investigated. The metalation of polycondensed aromatic rings of the carbon fiber surface was achieved by the treatment of carbon fiber with n-butyl-lithium (BuLi) in N, N, N′, N′ -tetramethylethylenediamine (TMEDA) or hexamethylphosphorous triamide (HMPT) at 0°C. The anionic polymerization of methyl methacrylate (MMA) and styrene (St) was initiated by the metallized carbon fiber, and these polymers were grafted onto the surface. The conversion and the percentage of grafting increased with increasing amount of BuLi used for the metalation of carbon fiber. When 0.20 g carbon fiber was treated with 0.3 mmol BuLi in TMEDA, the percentage of grafting of PMMA and PSt reached a maximum value (PMMA, 34.5%; PSt, 37.1 %). Furthermore, the metalation of aromatic rings of carbon fiber also proceeds by the treatment with BuLi in HMPT. On the contrary, no grafting was observed when carbon fiber was treated with BuLi in tetrahydrofuran (THF) or toluene. This may be due to the fact that metalation of carbon fiber does not proceed in THF or toluene.     

Cationic Grafting of Vinyl Polymers onto a Carbon Whisker,Initiated by Acylium Perchlorate Groups Introduced onto the Surface

Abstract

The cationic graft polymerization of vinyl monomers onto a carbon whisker, vapor-grown carbon fiber, initiated by acylium perchlorate groups introduced onto the surface, was investigated. The introduction of acylium perchlorate groups onto a carbon whisker was achieved by the treatment of a carbon whisker having acyl chloride groups, which were introduced by the reaction of surface carboxyl groups with thionyl chloride, with silver perchlorate in nitrobenzene. It was found that the cationic polymerization of vinyl monomers, such as styrene, indene, N-vinyl-2-pyrrolidone, and n-butyl vinyl ether, is initiated by acylium perchlorate groups on a carbon whisker. In the polymerization, the corresponding vinyl polymers were grafted onto a carbon-whisker surface based on the propagation of polymer from the surface: the percentage of grafting of polystyrene and polyindene reached 42.5 and 100.3%, respectively. The percentage of polystyrene grafting decreased with increasing polymerization temperature because of preferential chain transfer reactions at higher temperatures. Polymer-grafted carbon whisker gave a stable colloidal dispersion in a good solvent for grafted polymer.     

Anionic graft polymerization of vinyl monomers initiated by metallized aromatic rings of graphite powder

Anionic graft polymerizations of methyl methacrylate (MMA) and styrene from graphite powder initiated by metallized aromatic rings on the surface were investigated. Metalation of the surface was achieved by the reaction of polycondensed aromatic rings of graphite withn-butyllithium (BuLi) in N,N,N,N-tetramethylethylenediamine (TMEDA) or hexamethylphosphorous triamide (HMPT) at 0 °C., Anionic polymerizations of MMA and styrene were initiated by metallized graphite, and these polymers were grafted onto the surface. The conversion and percentage of grafting increased by increasing the amount of BuLi used for metalation. When 0.20 g of graphite was treated with 0.4–0.5 mmol of BuLi in TMEDA, the percentage of grafting of PMMA and polystyrene reached the maximum value: PMMA 52.8% (PMMA/graphite =0.528 g/1.0 g) and polystyrene 37.2% (polystyrene/graphite=0.372 g/1.0 g). Grafting of polymers was also confirmed by infrared spectra. Although no metalation of graphite proceeded in toluene, graphite could be metallized even in toluene by the addition of crown ether as a complexing cation agent. The stability of graphite powder in organic solvent dispersion was found to be improved remarkably by grafting of polymer onto the surface.     

Grafting of polyesters from carbon whisker surface: Copolymerization of epoxides with cyclic acid anhydrides initiated by COOK groups introduced onto the surface

To modify the surface of carbon whisker (vapor-grown carbon fiber) the grafting of polyesters by use of potassium carboxylate (COOK) groups introduced onto the surface was investigated. The introduction of COOK groups onto the carbon whisker was achieved by the treatment of surface carboxyl groups with KOH aqueous solution. Untreated carbon whisker has no ability to initiate the polymerization. It was found that the anionic ring-opening alternating copolymerization of epoxides with cyclic acid anhydrides is successfully initiated by COOK groups on the carbon whisker surface. The corresponding polyester was grafted onto the surface based on the propagation of polymer from COOK groups introduced on the surface. The percentage of grafting of the polyester from styrene oxide and phthalic anhydride was determined to be 91.0%. The polymerization rate and percentage of grafting increased upon addition of crown ether. Furthermore, the rate of polymerization increased with increasing the dielectric constant of the solvent, but the percentage of grafting decreased. Polyester-grafted carbon whisker was found to give a stable colloidal dispersion in a good solvent for the grafted polymer. © 1993 John Wiley & Sons, Inc.     

苯氧铜/正丁基锂体系引发MMA负离子聚合及其活性特征的研究

采用苯氧铜/正丁基锂(PhOCu/n-BuLi)体系引发MMA聚合, 通过GPC, ¹H NMR对聚合物进行了表征. 实验结果表明, 该体系聚合反应速度较快, 温度、引发体系组成是影响聚合物分子量及其分布、单体转化率、引发剂引发效率、聚合物的立构规整性的主要因素; －40 ℃时分子量分布比较窄, 但引发效率也比较低(大约15%). 低引发效率、宽分子量分布与引发剂的聚集状态有关. 分子量与单体浓度、引发剂浓度的关系说明, 该体系具有一定程度的活性聚合特点.     

Morphology and grafting of oxazoline-functional polymer particles with various carboxylic acids

Oxazoline-functionalized, crosslinked PMMA-particles, prepared by free radical nonaqueous dispersion polymerization, were grafted with n-decanoic acid and carboxylic acid-terminated polystyrene. Oxazoline groups, separated by an alkylspacer from the PMMA backbone, showed enhanced mobility with respect to the backbone, as evaluated by solid-state NMR spectroscopy using a dipolar filter. As a function of molecular mass of the carboxylic acid, the oxazoline conversion varied from 70 mol % for n-decanoic acid to 1% for monocarboxylate-terminated polystyrene CT-PS with M_n: 15,900 g/mol. Morphological studies, performed by TEM, showed that reaction with acid terminated polystyrene results exclusively in interfacial grafting at the particle surface. At low grafting levels a raspberry-like morphology was obtained, whereas grafting levels exceeding 14 wt % CT-PS resulted in core-shell morphology. Core-shell morphology was also verified by static light scattering using toluene solvent, which is isorefractive to the PMMA core. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1821–1827, 1998     

Graft polymerization of methyl methacrylate initiated by pendant azo groups introduced onto γ-poly(glutamic acid)

The grafting of poly(methyl methacrylate) (PMMA) onto biosynthesized γ-poly(glutamic acid) (γ-PGA) initiated by pendant azo groups introduced onto γ-PGA was performed. The introduction of pendant azo groups onto γ-PGA was achieved by the reaction of carboxyl groups of γ-PGA with azo initiators having hydroxyl or amino groups, such as 2,2-azobis[2-(hydroxymethyl)propionitrile] (AHP), 2,2′-azobis[2-methyl-N-(2-hydroxyethyl)propionamide] (AMHP), and 2,2′-azobis[2-(2-imidazolin-2-yl)propane] (AIP), using N,N′-dicyclohexylcarbodiimide. The amount of pendant AHP groups introduced onto γ-PGA was estimated to be 0.15 mmol/g. Untreated γ-PGA failed to initiate the polymerization of MMA. On the contrary, the polymerization of MMA was found to be initiated in the presence of γ-PGA having azo groups: the polymerization rate was proportional to the square root of the concentration of γ-PGA having pendant azo groups. During the polymerization PMMA was grafted onto γ-PGA; the percentage of grafting of PMMA onto γ-PGA obtained from the graft polymerization initiated by pendant AHP, AMHP, and AIP groups was evaluated to be 65.0, 53.1, and 29.0%, respectively. Differential scanning calorimetric analysis shows that the endotherm transition point of γ-PGA at 220°C disappears by the grafting of PMMA onto the polymer. © 1993 John Wiley & Sons, Inc.     

Photografting of vinyl polymers onto ultrafine inorganic particles: Photopolymerization of vinyl monomers initiated by AZO groups introduced onto these surfaces

The photografting of polymers onto ultrafine inorganic particles, such as silica and titanium oxide, initiated by azo groups introduced onto these surfaces was investigated. The introduction of azo groups onto the particles was achieved by the reaction of 4,4′-azobis(4-cyanopentanoic acid) with surface isocyanate groups, which were introduced by the treatment with tolylene 2,4-diisocyanate. It was found that the photopolymerization of vinyl monomers, such as methyl methacrylate (MMA), styrene, and N-vinylcarbazole, is initiated by ultrafine particles having azo groups. The corresponding polymers were effectively grafted onto these surfaces through the propagation of the polymer from the surface radicals formed by the photodecomposition of the azo groups: e.g., the percentage of grafting of PMMA and polystyrene onto silica was reached to 112 and 176%, respectively. The percentage of grafting onto silica in the graft polymerization initiated by photodecomposition of surface azo groups was much larger than that initiated by thermal decomposition. Polymer-grafted ultrafine particles thus obtained gave a stable colloidal dispersion in good solvents for the grafted chain. © 1994 John Wiley & Sons, Inc.     

Living radical graft polymerization of methyl methacrylate to polyethylene film with typical and reverse atom transfer radical polymerization

Nickel‐mediated atom transfer radical polymerization (ATRP) and iron‐mediated reverse ATRP were applied to the living radical graft polymerization of methyl methacrylate onto solid high‐density polyethylene (HDPE) films modified with 2,2,2‐tribromoethanol and benzophenone, respectively. The number‐average molecular weight (M_n) of the free poly(methyl methacrylate) (PMMA) produced simultaneously during grafting grew with the monomer conversion. The weight‐average molecular weight/number‐average molecular weight ratio (M_w/M_n) was small (<1.4), indicating a controlled polymerization. The grafting ratio showed a linear relation with M_n of the free PMMA for both reaction systems. With the same characteristics assumed for both free and graft PMMA, the grafting was controlled, and the increase in grafting ratio was ascribed to the growing chain length of the graft PMMA. In fact, M_n and M_w/M_n of the grafted PMMA chains cleaved from the polyethylene substrate were only slightly larger than those of the free PMMA chains, and this was confirmed in the system of nickel‐mediated ATRP. An appropriate period of UV preirradiation controlled the amount of initiation groups introduced to the HDPE film modified with benzophenone. The grafting ratio increased linearly with the preirradiation time. The graft polymerizations for both reaction systems proceeded in a controlled fashion. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3350–3359, 2002     

Graft polymerization from pore wall of three-dimensionally ordered macroporous cross-linked polystyrene via atom transfer radical polymerization

The surface-initiated atom-transfer radical polymerization (ATRP) technique was applied to the graft polymerization of methyl methacrylate (MMA) and N-isopropylacrylamide (NIPAm) from three-dimensionally ordered macroporous cross-linked polystyrene (3DOM CLPS) on which the initiator, halogen atom was immobilized onto the pore wall of 3DOM CLPS by chloromethylation. FT-IR and TG-DWA analyses confirm that the graft polymerization of MMA and NIPAm via ATRP had been taken place at the pore wall of 3DOM CLPS. The initiating efficiency of chloromethyl groups was calculated according to the data of TGA-titration, revealed that the benzyl chloride is not only distributed on the surface of the pore walls but also must be present throughout the inner of the cross-linked polystyrene matrix. SEM analyses show that the grafted layers are smooth and homogeneous, and the ordered structure is well preserved after polymerization. By the adjustment of the graft polymerization time, the thickness of grafted polymer layers can be controlled. The max thickness of grafted PMMA layer is 85 nm and the max thickness of grafted PNIPAm layer is 35 nm.     

Functionalization of Graphene Sheets via Chemically Grafting of PMMA Chains Through in-situ Polymerization

In this work, we report the preparation of graphene nanoplatelet which covalently functionalized with PMMA chains by introduction of vinyl groups onto graphene surface through simple esterification reaction between hydroxyl groups of graphite oxide and methacrylic anhydride. The synthesis is followed by in-situ polymerization with MMA monomers. The structural properties were characterized with X-ray diffraction spectroscopy (XRD) and scanning electronic microscopy (SEM) that showed the crystalline graphite is converted to individual layers during the synthesis steps. The grafting of PMMA chains was monitored with IR spectroscopy (FT-IR) and thermogravimetric analysis (TGA). The TGA results revealed 40% wt of PMMA chains chemically grafted onto graphene surface. Significant increase in glass transition temperature (T_g) and existence of polymer chains in two positions (physically absorbed and chemically grafting onto graphite surface) are indicated by differential scanning calorimetric (DSC) analysis.     

Synthesis and kinetics of graft polymerization of methyl methacrylate from the RAFT coordinated surface of nano‐TiO2

Polymer chains of PMMA were grown from nano titania (n‐TiO₂) by the reversible addition‐fragmentation chain transfer polymerization process. The mechanism and kinetics of MMA polymerization from both solution and “grafted from” n‐TiO₂ were studied. The RAFT agent, 4‐cyano‐4‐(dodecylsulfanylthiocarbonyl) sulfanyl pentanoic acid, with an available carboxyl group was used to anchor onto the n‐TiO₂ surface, with the S?C(SC₁₂H₂₅) moiety used for subsequent RAFT polymerization of MMA to form n‐TiO₂/PMMA nanocomposites. The functionalization of n‐TiO₂ was determined by FTIR, XPS, partitioning studies, and thermal analysis. The livingness of the polymerization was verified using NMR and GPC, while the dispersion of the inorganic filler in the polymer was studied using electron microscopy, FTIR, and thermal analysis. The monomer conversion and molecular weight kinetics were explored for the living RAFT polymerization, both in solution and grafted from n‐TiO₂, with first‐order kinetics being observed in both cases. Increased graft density on n‐TiO₂ led to a lower rate of polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3926–3937, 2008     

Synthesis of poly(methyl methacrylate)‐b‐polystyrene containing a crown ether unit at the junction point via combination of atom transfer radical polymerization and nitroxide mediated radical polymerization routes

Poly(methyl methacrylate)‐b‐polystyrene (PMMA‐b‐PS) containing a benzo‐15‐crown‐5 unit at the junction point was prepared by combining atom transfer radical polymerization and nitroxide‐mediated radical polymerization. For this purpose, 6,7,9,10,12,13,15,16‐octahydro‐5,8,11,14,17‐pentaoxa‐benzocyclopentadecene‐2‐carboxylic acid 3‐(2‐bromo‐2‐methyl‐propionyloxy)‐2‐methyl‐2‐[2‐phenyl‐2‐(2,2,6,6‐tetramethyl‐piperidin‐1‐yloxy)‐ethoxycarbonyl]‐propyl ester ( 3 ) was synthesized and used as an initiator in atom transfer radical polymerization of methyl methacrylate in the presence of CuCl and pentamethyldiethylenetriamine at 60°C. A linear behavior was observed in both plots of ln([M]₀/[M]) versus time and M_n,_GPC versus conversion indicating that the polymerization proceeded in a controlled/living manner. Thus obtained PMMA precursor was used as a macroinitiator in nitroxide‐mediated radical polymerization of styrene (St) at 125°C to give well‐defined PMMA‐b‐PS with crown ether per chain. Kinetic data were also obtained for copolymerization. Moreover, potassium picrate (K⁺ picrate) complexation of 3 and PMMA‐b‐PS copolymer was studied. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3242–3249, 2006     

Preparation of poly(methyl methacrylate) grafted hydroxyapatite nanoparticles via reverse ATRP

Surface-initiated reverse atom transfer radical polymerization (reverse ATRP) technical was successfully employed to modify hydroxyapatite (HAP) nanoparticles with poly(methyl methacrylate) (PMMA). The peroxide initiator moiety for reverse ATRP was covalently attached to the HAP surface through the surface hydroxyl groups. Reverse ATRP of methyl methacrylate (MMA) from the initiator-functionalized HAP was carried out, and the end bromide groups of grafted PMMA initiated ATRP of MMA subsequently. Fourier transformation infrared (FTIR) spectroscopy, thermal gravimetric analysis (TGA) and transmission electron microscopy (TEM) were employed to confirm the grafting and to characterize the nanoparticle structure. The grafted PMMA gave HAP nanoparticles excellent dispersibility in MMA monomer. As the amount of grafted PMMA increased, the dispersibility of surface-grafted HAP and the compressive strength of HAP/PMMA composites were improved.     

Radical polymerization of methyl methacrylate initiated by an enolizable ketone–carbon black system

The polymerization of methyl methacrylate (MMA) initiated by an enolizable ketone (R₁? CO? CH₂? CO? R₂)-carbon black system was investigated. Although enolizable ketone itself could not do so, the polymerization of MMA was initiated by enolizable ketone in the presence of carbon black. In addition, a chloranil-enolizable ketone system was able to initiate the polymerization of MMA. It was found that the enol form of the ketone and quinonic oxygen groups on the carbon black surface played an important role in the initiation system; namely, it was considered that the polymerization was begun by the ketone radical (R₁? CO? CH? CO? R₂) formed by a one-electron transfer reaction from enolate ion to quinonic oxygen groups. The effect of solvent on the process was also studied. The rate of the polymerization increased, depending on the solvent used, in the following order: benzene < 1,4-dioxane < dimethyl sulfoxide < N,N-dimethylformamide < N-methyl-2-pyrrolidone. Furthermore, it became apparent that during the polymerization poly(methyl methacrylate) was grafted onto the carbon black surface (grafting ratio was ca. 40% when benzene was used as solvent) and the carbon black obtained gave a stable colloidal dispersion in organic solvent.     

Polymer grafting onto carbon black by use of TEMPO-terminated polystyrene with controlled molecular weight

The grafting of polystyrene with controlled molecular weight and narrow molecular weight distribution onto the carbon black surface through the trapping of polymer radicals formed by the thermal dissociation of 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO)-terminated polystyrene (PSt-TEMPO) by the carbon black surface was investigated. PSt-TEMPO was prepared by living radical polymerization of St with the benzoyl peroxide/TEMPO system. When PSt having no terminal TEMPO moiety was heated with carbon black, no grafting of PSt onto the surface was observed. On the contrary, by the heating of PSt-TEMPO with carbon black in m-xylene at 125°C, PSt with controlled molecular weight and narrow molecular weight distribution was grafted onto the surface: the percentage grafting of PSt (M_n = 3.2 × 10³;M_w/M_n = 1.07) onto furnace black was determined to be 16.0%. On the basis of the above results, it is concluded that PSt radicals formed by the thermal dissociation of the C ON bond between PSt and TEMPO are trapped by polycondensed aromatic rings of carbon black. The mole number of grafted PSt chains on the carbon black surface decreased with increasing molecular weight of PSt-TEMPO. PSt-grafted carbon black gave a stable colloidal dispersion in THF. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3165–3172, 1998     

Cyclodextrins in polymer synthesis: free radical polymerization of cyclodextrin host‐guest complexes of methyl methacrylate or styrene from homogenous aqueous solution

The polymerization of methylated β‐cyclodextrin (m‐β‐CD) 1 : 1 host‐guest compounds of methyl methacrylate (MMA) ( 1 ) or styrene ( 2 ) is described. The polymerization of complexes 1 a and 2 a was carried out in water with potassium peroxodisulfate (K₂S₂O₈)/sodium hydrogensulfite (NaHSO₃) as radical redox initiator at 60°C. Unthreading of m‐β‐CD during the polymerization led to water‐insoluble poly(methyl methacrylate) (PMMA) ( 3 ) and polystyrene ( 4 ). By comparison, analogously prepared polymers from uncomplexed monomers 1 and 2 in ethanol as organic solvent with 2,2′‐azoisobutyronitrile (AIBN) as radical initiator showed significantly lower molecular weights and were obtained in lower yields in all cases. Polymerization of m‐β‐CD complexed MMA in water, initiated with 2,2′‐azobis(N,N ′‐dimethyleneisobutyroamidine) dihydrochloride, occurred much faster than the polymerization of uncomplexed MMA in methanol under similar conditions. Furthermore, it was shown, that the precipitation polymerization of complexed MMA from homogeneous aqueous solution can be described by equations (P_n^–1 ∝ lsqb;Irsqb;^0.5) similar to those for classical polymerization in solution.     

可聚合的光引发转移终止剂合成接枝共聚物

采用一种可聚合的光引发转移终止剂 ,2 N ,N 二乙基二硫代氨基甲酰氧基乙酸 β 甲基丙烯酰氧基乙酯 (MAEDCA) ,通过两种途径制备了含有聚甲基丙烯酸甲酯 (PMMA)和聚苯乙烯 (PSt)链段的接枝共聚物 .其一是将MAEDCA作为引发剂 ,在紫外光照射下引发MMA聚合 ,得到大分子单体 ,通过大分子单体与St的共聚合得到 .考察了所用大分子单体的分子量和浓度对共聚合的影响 .其二是将MAEDCA作为单体与MMA共聚得到侧链上含有N ,N 二乙基二硫代氨基甲酰氧基 (DC)基团的无规共聚物 ,P(MMA co MAEDCA) .在紫外光照射下 ,P(MMA co MAEDCA)作为大分子引发剂引发St聚合 ,得到P(MMA co MAEDCA) g PSt的共聚物 ,研究了接枝共聚合过程的活性自由基聚合特征     

Radical polymerization of methyl methacrylate with ethane-1,1,2-triyltribenzene as an initiator and ethane-1,1,2-triyltribenzene-end polymers as macroinitiators

An unsymmetrical triphenylethane, ethane-1,1,2-triyltribenzene (ETB), was successfully prepared from phenyl lithium, trans-1,2-diphenylethylene, and methanol. Characterization of the compound was performed by ¹H and ¹³C nuclear magnetic resonance spectroscopy (NMR). The polymerization of methyl methacrylate (MMA) was performed in the presence of ETB at 85 °C or higher. The free radicals obtained were characterized by ultra-performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (UPLC/Q-TOF MS). Gel permeation chromatography (GPC) traces of the average molecular weight of poly(MMA) (PMMA) showed a series of translations with increasing time. The average molecular weight of PMMA indicated narrow polydispersity, and a linear relationship was found between ln([M]₀/[M]) and polymerization time. These results indicated the “living” nature of the polymerization of MMA in the presence of ETB. The structure of ETB was also introduced to the end of polystyrene (PS), polyisoprene (PI), and polyisoprene-b-polystyrene (PIS) chains which were obtained by living anionic polymerization. Hence, they initiated radical polymerization of MMA as ETB-end-macroinitiators to obtain block copolymers. Thus, living anionic polymerization and this radical polymerization method were combined together to prepare block copolymers without the intermediate transformation step.     

Compatibilizing effect of a graft copolymer on bacterial poly(3‐hydroxybutyrate)/poly(methyl methacrylate) blends

Blends of isotactic (natural) poly(3‐hydroxybutyrate) (PHB) and poly(methyl methacrylate) (PMMA) are partially miscible, and PHB in excess of 20 wt % segregates as a partially crystalline pure phase. Copolymers containing atactic PHB chains grafted onto a PMMA backbone are used to compatibilize phase‐separated PHB/PMMA blends. Two poly(methyl methacrylate‐g‐hydroxybutyrate) [P(MMA‐g‐HB)] copolymers with different grafting densities and the same length of the grafted chain have been investigated. The copolymer with higher grafting density, containing 67 mol % hydroxybutyrate units, has a beneficial effect on the mechanical properties of PHB/PMMA blends with 30–50% PHB content, which show a remarkable increase in ductility. The main effect of copolymer addition is the inhibition of PHB crystallization. No compatibilizing effect on PHB/PMMA blends with PHB contents higher than 50% is observed with various amounts of P(MMA‐g‐HB) copolymer. In these blends, the graft copolymer is not able to prevent PHB crystallization, and the ternary PHB/PMMA/P(MMA‐g‐HB) blends remain crystalline and brittle. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1390–1399, 2002