PHBV纳米纤维的静电纺丝及在生物医用领域的研究进展

聚(3-羟基丁酸酯-3-羟基戊酸酯)(PHBV)纳米纤维具有高比表面积、高孔隙率、生物相容性、生物降解性等优点,可用作生物医用材料。本文综述了基于静电纺丝法制备的PHBV纳米纤维及其在生物医用领域的研究进展,讨论了PHBV纺丝溶液的溶剂、浓度、外加盐类以及聚合物等对PHBV纳米纤维形貌、结构及性能的影响规律,结合目前PHBV纳米纤维在组织工程和药物运输载体的研究现状,重点概述了其亲水改性、力学性能改善、功能化改性的研究进展。最后,对静电纺丝法制备PHBV纳米纤维存在的一些问题进行分析,并对其未来发展趋势和前景进行展望。     

离子浓度对电纺纤维沉积形态及表面形貌的影响

通过采用传统电纺丝装置(接收板接地或连接负压电源)、逆向电场及非接触式电纺丝装置等4种不同的电纺丝装置,在相同电压、接收距离、纺针直径、温湿度条件下,对20%的聚乙烯醇溶液进行电纺丝实验,观察不同装置中制得的纤维的沉积形态与形貌.还采用ANSYS有限元模拟对电纺丝装置的场强分布进行分析,并引入电化学理论解释了采用不同电纺装置时离子浓度的不同对所得电纺纤维形貌的影响,分析了产生差异的原因.     

聚(3-羟基丁酸酯-co-3-羟基戊酸酯)改性及纤维成形北大核心CSCD

聚(3-羟基丁酸酯-co-3-羟基戊酸酯)(PHBV)是一种微生物发酵生产的热塑性聚合物。从物理、化学改性及其纤维成形两个方面综述了PHBV的研究进展。PHBV的物理改性主要有无机纳米粒子共混体系(PHBV/iNPs)、有机纳米晶共混体系(PHBV/oNPs)、高聚物共混体系(PHBV/Polymer)和绿色全降解共混体系;化学结构构筑主要包括接枝共聚改性、嵌段共聚改性、端基扩链改性等。从改性的手段及介质,分析了改性方法的优缺点。PHBV纤维的成形方法主要有熔融纺丝法、干法纺丝法及静电纺丝法。从PHBV纤维应用领域看,熔融纺纤维应用目标在于替代现有石油基相关产品,而静电纺纤维主要应用于开拓组织工程再生医学领域。最后,对PHBV今后的研究及发展提出了展望。     

聚丙烯腈纳米纤维的再细化

通过电纺丝法研究了溶剂种类、溶液浓度、纺丝倾斜角、聚合物分子量对纳米纤维形态和直径的影响,寻找到最佳工艺条件,并得到了平均直径为20nm的超细纤维.     

聚甲醛电纺纤维表面孔结构的控制

研究了环境相对湿度、 温度、 溶液浓度、 纺丝电压和接收距离对聚甲醛(POM)电纺纤维表面孔形貌的影响. 结果表明, 空气中一定含量的水对孔的形成至关重要; 纺丝液浓度对孔的大小有影响. 并对POM 纤维表面成孔的可能机理进行了分析.     

静电纺丝法制备PVP螺旋纤维及其机理研究

研究了电纺丝聚乙烯吡咯烷酮螺旋纤维的形成条件, 在9kV的电压下, 由于溶液质量分数的增加(12%-24%), 纤维形态呈现出直线→螺旋→折叠→无序的变化趋势; 在质量分数为20%时, 随着纺丝电压的增加, 纤维形态呈现出折叠→螺旋→无序的变化趋势, 同时对螺旋纤维的形成机理进行了讨论, 在纺丝过程中纤维束所带静电荷之间的库仑斥力是形成螺旋纤维的直接动力.     

硫化锌／聚对苯乙炔纳米纤维的制备及表征

为了制备一种形态完美、荧光较强的无机一聚合物纤维,采用静电纺丝的方法制备了硫化锌／聚对苯乙炔复合纳米纤维,研究纤维的性质过程中使用了扫描电子显微镜、荧光光谱仪、荧光显微镜和X-射线衍射仪。纤维的直径大约为400nm,其形态与直径随着电纺溶液中醋酸锌的浓度改变而不同,通过荧光显微镜与荧光光谱仪可以知道该纤维具有荧光性质,...     

静电纺丝法制备聚甲醛纳米纤维

以六氟异丙醇为溶剂, 用静电纺丝的方法制备了聚甲醛纳米纤维. 利用场发射扫描电镜对纤维形貌进行了表征, 纤维的直径为0.3~1.2 μm. 讨论了溶液浓度、接收距离、电压和温度等纺丝参数对纤维形貌的影响. 用DSC方法对电纺纤维膜的结晶性能进行了研究, 并与溶液浇铸膜的进行了比较. 结果表明, 电纺纤维膜的熔点与溶液浇铸膜的相同, 与溶液的浓度无关, 但结晶度比溶液浇铸膜的低. 力学性能用拉伸试验进行了测试, 观察到很长的断裂伸长率.     

二氧化碳-环氧丙烷共聚物电纺纤维形貌研究

利用电纺丝技术制备了二氧化碳环氧丙烷共聚物超细纤维,研究了喷丝口电势、纺丝距离、浓度、溶剂等因素对纤维形貌、直径及均一性的影响.实验结果表明,利用电纺丝法可以制备直径在小于200nm到7μm二氧化碳环氧丙烷共聚物纤维;喷丝口电势和浓度对于共聚物电纺丝纤维是否形成串珠结构有重要影响;电势、距离和纺丝液浓度都对纤维直径及分散系数有较大影响,在一定范围内,随着喷丝口电势增加,纤维平均直径变大而分散系数变小;纺丝距离增大使得纤维平均直径变小,分散系数变大;浓度的增大使得纤维平均直径变大,分散系数变小;不同溶剂配制的溶液体系制备的电纺丝纤维形貌有很大差异,在二氯甲烷和丁酮的体系中,分别观察到了两组较为集中的直径分布.     

电纺聚氧化乙烯纤维的分散形态和结晶行为研究

将聚氧化乙烯(PEO)水溶液在不同的工艺条件下进行电纺,制备了PEO纤维.用SEM研究了纤维的分散形态;用DSC和XRD研究了纤维的结晶性能.电纺纤维分散形态是由浓度、电压、固化距离等因素综合作用的结果.其中,浓度是最关键的因素.降低溶液浓度,提高静电压和增加固化距离均会使纤维变细.电纺得到的纤维与原粉相比,电纺使纤维结晶度下降,理论上分析了可能的机理.     

Characterization of poly(methyl methacrylate) nanofiber mats by electrospinning process

In this study, the aim is to describe the influence of electrospinning parameters on the morphology, the water wetting property and dye adsorption property of poly(methyl methacrylate) nanofiber mats. Specifically, the effects of solution concentration, solvent type, applied voltage, distance between the electrodes and particulate reinforcement on the diameter and shape of the nanofibers were investigated. All poly(methyl methacrylate) nanofiber mats contained beaded nanofiber structures. With increasing the polymer solution concentration, the average fiber diameter also increased. Poly(methyl methacrylate) nanofiber mat electrospun from dimethylformamide solution resulted in thicker fibers when compared with the mat electrospun from acetone solution. Increasing the electric potential difference between the collector and the syringe tip did not increase the average fiber diameter. Besides increasing the distance between the electrodes resulted in a decrease in the average fiber diameter. When compared with PMMA nanofiber mat, thicker fibers were obtained with silica nanoparticles reinforced nanofiber mat. According to the water contact angle measurements, all poly(methyl methacrylate) nanofiber mats revealed hydrophobic surface property. PMMA nanofiber mat with the highest water contact angle gave rise to the highest dye adsorption capacity.     

Electrospinning of nylon-6,66,1010 terpolymer

Ultrafine nylon fibers were prepared by electrospinning of nylon-6,66,1010 terpolymer solution in 2,2,2-trifluoroethanol (TFE). The morphology, crystallinity and mechanical properties of the electrospun nylon-6,66,1010 fibers were investigated by scanning electron microscope (SEM), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and tensile test. The effects of electrospun process parameters such as solution concentration, voltage and tip-to-collector distance on the morphology and the average size of the electrospun fibers were also studied. The results show that the spinnable concentration of nylon-6,66,1010/TFE solution is in the range of 6-14 wt%, and higher solution concentration favors the formation of uniform fibers without beads. The diameters of the electrospun fibers increase with increasing the solution concentration and decrease slightly with increasing the voltage and needle tip-to-collector distance. But no obvious morphology changes were found with the increase of the voltage and collection distance. DSC and WAXD results suggest that the electrospun nylon-6,66,1010 membranes have lower crystallinity than those of the corresponding casting films. The electrospun nylon-6,66,1010 membrane obtained from the 14 wt% concentration exhibits the largest tensile strength and elongation at break.     

Study on morphology of electrospun poly(vinyl alcohol) mats

Submicron poly(vinyl alcohol) (PVA) fiber mats were prepared by electrospinning of aqueous PVA solutions in 6-8% concentration. Fiber morphology was observed under a scanning electron microscope and effects of instrument parameters including electric voltage, tip-target distance, flow rate and solution parameters such as concentration on the morphology of electrospun PVA fibers were evaluated. Results showed that, when PVA with higher degree of hydrolysis (DH) of 98% was used, tip-target distance exhibited no significant effect on the fiber morphology, however the morphological structure can be slightly changed by changing the solution flow rate. At high voltages above 10 kV, electrospun PVA fibers exhibited a broad diameter distribution. With increasing solution concentration, the morphology was changed from beaded fiber to uniform fiber and the average fiber diameter could be increased from 87 ± 14 nm to 246 ± 50 nm. It was also found that additions of sodium chloride and ethanol had significant effects on the fiber diameter and the morphology of electrospun PVA fibers because of the different solution conductivity, surface tension and viscosity. When the DH value of PVA was increased from 80% to 99%, the morphology electrospun PVA fibers was changed from ribbon-like fibers to uniform fibers and then to beaded fibers. The addition of aspirin and bovine serum albumin also resulted in the appearance of beads.     

Influence of a mixing solvent with tetrahydrofuran and N,N‐dimethylformamide on electrospun poly(vinyl chloride) nonwoven mats

We evaluated the effects of the solvent composition with respect to the solution concentration, applied electric field, and tip‐to‐collector distance on the morphology of electrospun poly(vinyl chloride) (PVC) fibers. The solvent volume ratio was strongly correlated with the diameter of the electrospun fibers with respect to the other processing parameters. Electrospun PVC fibers dissolved in tetrahydrofuran (THF) had diameters ranging from 500 nm to 6 μm; those dissolved in N,N‐dimethylformamide (DMF) had an average diameter of 200 nm. The diameters of the electrospun fibers were obtained from narrow to broad distributions with the solvent composition. Also, the diameters of fibers electrospun from a mixed solvent of THF and DMF were less than 1 μm. The mechanical properties of electrospun PVC nonwoven mats depended on the fiber orientation and linear velocity of the drum surface. With increasing linear velocity of the drum surface, electrospun PVC fibers were arranged toward the machine direction, and the dimensions of the spiral path were shorter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2259–2268, 2002     

Superhydrophobicity of PHBV fibrous surface with bead-on-string structure

A poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) fibrous surface with various bead-on-string structures was fabricated by electrospinning. PHBV was electrospun at various concentrations and then CF4 plasma treatment was employed to further improve the hydrophobicity of the PHBV fiber surfaces. The surface morphology of the electrospun PHBV mats was observed by scanning electron microscopy (SEM). The surface properties were characterized by water contact angle (WCA) measurements and X-ray photoelectron spectroscopy (XPS). The surface morphology of the electrospun PHBV fibrous mats with the bead-son-string structure varied with the solution concentration. The WCA of all of the electrospun PHBV mats was higher than that of the PHBV film. In particular, a very rough fiber surface including porous beads was observed when PHBV was electrospun from the solution with a concentration of 26 wt%. Also, its WCA further increased from 141 degrees to 158 degrees after CF(4) plasma treatment for 150 s. PHBV can be rendered superhydrophobic by controlling the surface morphology and surface energy, which can be achieved by adjusting the electrospinning and plasma treatment conditions.     

Diameter control of electrospun chitosan‐collagen fibers

In this article, the effects of fundamental parameters including applied voltage, feed rate of solution, collecting distance of fibers, the ratio of chitosan to collagen in the fibers and polymer solution concentration on the diameter and morphology of electrospun collagen‐chitosan complex nanofibers were studied to produce ultrafine polymer fibers. Based on the systematic parametric study, it is possible to control the diameter and morphology of the electrospun polymer fibers. This will also be helpful for electrospinning of various polymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1949–1955, 2009     

Diameter control of electrospun polyacrylonitrile/iron acetylacetonate ultrafine nanofibers

Electrospinning is the process of producing ultrafine fibers by overcoming the surface tension of a polymer solution using high voltage. In this work, the effects of both solution properties (viscosity, conductivity, and surface tension) and operational conditions (voltage, feed rate, and spinneret‐collector distance), on the structure of electrospun polyacrylonitrile nanofibers, were systematically investigated. Iron acetylacetonate was added to the electrospinning solution to control fiber diameter by selectively adjusting solution properties. It was found that, with increased salt concentration, the fiber diameter increases and then passes through a maximum due to changes in solution viscosity, conductivity, and surface tension. In addition, the fiber diameter increases with increase in voltage, feed rate, and spinneret‐collector distance. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1611–1618, 2008     

Electrospun fiber mats of poly(3‐hydroxybutyrate), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate), and their blends

Electrospinning of poly(3‐hydroxybutyrate) (PHB), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV), and their blends was first carried out in chloroform at 50 °C on a stationary collector. The average diameter of the as‐spun fiber from PHB and PHBV solutions decreased with increasing collection distance and increased with increasing solution concentration and applied electrical potential. In all of the spinning conditions investigated, the average diameter of the as‐spun pure fibers ranged between 1.6 and 8.8 μm. Electrospinning of PHB, PHBV, and their blends was carried out further at a fixed solution concentration of 14% w/v on a homemade rotating cylindrical collector. Well‐aligned, cross‐sectionally round fibers without beads were obtained. The average diameter of the as‐spun pure and blend fibers ranged between 2.3 and 4.0 μm. The as‐spun fiber mats appeared to be more hydrophobic than the corresponding films and much improvement in the tensile strength and the elongation at break was observed for the blend fiber mats over those of the pure fiber ones. Lastly, indirect cytotoxicity evaluation of the as‐spun pure and blend fiber mats with mouse fibroblasts (L929) indicated that these mats posed no threat to the cells. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2923–2933, 2006     

Preparation and characterization of antimicrobial polycarbonate nanofibrous membrane

Electrospinning of polycarbonate (PC)/chloroform solution with quaternary ammonium salt (benzyl triethylammonium chloride, BTEAC) was investigated to develop antimicrobial nanofibrous membranes for ultrafiltration. With BTEAC additive, ultrafine PC fibers were continuously generated and densely mounted without the blockage of spinning tip on electrospinning. When small amounts of BTEAC were added to the PC solution, the average diameter was also decreased from several micrometers to submicron range. It was found that the conductivity of the PC solution was a major parameter affecting the morphology and diameter of the electrospun PC fibers as well as the electrospinnability of PC. The nanofibrous membranes electrospun from the PC solution with BTEAC exhibited better excellent antimicrobial activity than those prepared without BTEAC. The PC nanofibrous filter shows a good filtration efficiency to satisfy the criterion of HEPA filter, and the pressure drop of the PC filters are within the normal range. Therefore, PC nanofibrous membrane showed a great potential as a candidate for ultrafiltration, compared to a commercial HEPA filter.