Special features of discharge characteristics of different types of lithium-thionyl chloride cells and the problem of their diagnostics

The problem of using discharge and noise characteristics of primary cells with the lithium-thionyl chloride system is examined in order to monitor the state of these power sources (primarily their depth of discharge). An analysis of special features of the discharge curves for lithium-thionyl chloride cells of the bobbin and jellyroll type, as well as the intensity of voltage fluctuations and power spectra of the electrochemical noises of these cells, leads to the conclusion that it is possible in principle to perform diagnostics on them, primarily to identify power sources that are significantly discharged (more than 70–80%).     

Substitution of aqua ligands fromcis-diaqua-bis(bipyridyl) ruthenium(II) by 1, 10-phenanthroline in aqueous medium

The kinetics of aqua ligand substitution fromcis-[Ru(bipy)₂(H₂O)₂]²⁺ by 1, 10-phenanthroline (phen) have been studied spectrophotometrically in the 35 to 50°C temperature range. We propose the following rate law for the reaction within the 3.65 to 5.5 pH range:

Signal enhancement of lead and arsenic in soil using laser ablation combined with fast electric discharge

In comparison to the traditional single pulse laser induced breakdown spectroscopy (SP-LIBS), a significant enhancement of atomic emission of lead and arsenic from laser plasma of soil has been demonstrated by the use of a laser ablation and fast pulse discharge plasma spectroscopy technique (LA-FPDPS). In this technique, a specifically designed high voltage and rapid discharge circuit was used to reheat the laser plasma and to enhance the plasma emission. A rapid and time damped alternating discharge current was observed with a short oscillating period ∼ 0.6 μs and sustained for about 6 μs. The peak intensities of Pb (283.31 nm) and As (286.04 nm) lines from soil plasma emission were greatly enhanced when compare to the traditional single pulse (SP) LIBS system. In addition, the precision of measurements in terms of the relative standard deviation (RSD) and the signal to noise (S/N) ratios were also improved. Scanning electron microscopy (SEM) images of the laser ablation regions indicated that the plasma reheating by the discharge spark was presumably the main mechanism for observed signal enhancement in the LA-FPDPS technique.     

Thermal runaway and fire behavior investigation of lithium ion batteries using modified cone calorimeter

The lithium ion battery has been widely used, but it has high fire risk due to its flammable materials. In this study, a series of combustion tests are conducted on the 18650-type lithium ion batteries using the modified cone calorimeter. The temperature and voltage variation of the battery, heat release rate and gas generation during combustion are measured in this study. The battery is heated evenly by the self-made heater, and the reliable trigger temperatures of thermal runaway are obtained for different states of charge (SOCs) batteries in this study. The fire behavior of the 100% SOC batteries is shown in this paper. The net heat absorption by the battery before thermal runaway is calculated based on the heat transfer theory. It ranges from 56.81 to 64.05 kJ for 0 to 100% SOC batteries, which shows a decreasing trend as SOC increases. The peak combustion heat release rate of 100% SOC batteries is 3.747?±?0.858 kW. CH₄ and CO gases are detected before and after thermal runaway. The generation of CO shows an increasing trend as SOC increases. Some suggestions on the early warning system of battery thermal runaway are proposed based on this study.

     

Time-resolved Optical Emission Spectroscopy in Water Electrical Discharges

The characteristics of the plasma initiated in ultrapure water between pairs of tungsten and tantalum electrodes were investigated by time-resolved optical emission spectroscopy. The deexcitation processes of the reactive species formed in the water plasma depended on the electrode material, but had been independent on the polarity of the applied voltage pulses. All the reactive species presented the same evolution with time and have been identified with high concentration in the emission spectra between the pulses. The current–voltage characteristics showed the features of a spark discharge for the both types of electrodes used in the process. When tantalum electrodes were used to generate the discharge, a broad emission continuum (350–940 nm) dominated the spectrum due to a transition to arc discharge.     

Spin–orbit coupling in oxygen containing diradicals

Intermediate diradicals which occur in the Paterno–Büchi photocycloaddition and in the Norrish type I photoreactions have been calculated taking into account the spin–orbit coupling (SOC) between the singlet (S) and triplet (T) states. Reaction paths for the photocycloaddition of formaldehyde to ethene and the diradical products of the α-cleavage of cyclohexanone have been optimized by the MNDO CI method for a number of different singlet and triplet states. SOC integrals are calculated by an effective one-electron approximation. Intermediate diradicals in the Paterno–Büchi reaction and the SOC effects are also studied ab initio with CAS SCF geometry optimization in a TZV basis set. Both methods predict a large SOC matrix element between the S and T states in the course of the C–C attack, while the SOC integral is two orders of magnitude smaller for the diradical produced in the C–O attack. In the Norrish type I photoreaction the oxygen atom also produces some nonzero contribution to the SOC integral which governs intersystem crossing in a ·C–C· diradical. For the diradicals produced by the α-cleavage of cyclohexanone a vibronic interaction is responsible for the SOC mixing between the lowest S and T states. The importance of one-center versus two-center SOC contributions in diradicals is briefly discussed.     

Structures and bonding in K0.91U1.79S6 and KU2Se6

The compounds K0.91U1.79S6 and KU2Se6, members of the AAn2Q6 actinide family (A = alkali metal or Tl; An = Th or U; Q = S, Se, or Te), have been synthesized from US2, K2S, and S at 1273 K and U, K2Se, and Se at 1173 K, respectively. KU2Se6 shows Curie-Weiss behavior above 30 K and no magnetic ordering down to 5 K. The value of mu(eff) is 2.95(1) mu(B)/U. Its electronic spectrum shows the peaks characteristic of 5f-5f transitions. It is a semiconductor with an activation energy of 0.27 eV for electrical conduction. Both K0.91U1.79S6 and KU2Se6 crystallize in space group Immm of the orthorhombic system and are of the KTh2Se6 structure type. Both contain infinite one-dimensional linear Q-Q chains characteristic of the AAn2Q6 family. Typical of the known AAn2Q6 compounds, in KU2Se6, there are two alternating Se-Se distances of 2.703(2) and 2.855(2) A, both much longer than an Se-Se single bond. In contrast, in K0.91U1.79S6, the first sulfide of this family to be characterized structurally, there are alternating normal S2(2-) pairs 2.097(5) A in length. In K0.91U1.79S6, the formal oxidation state of U is 4+.     

Electrical Features of Radio-frequency,Atmospheric-pressure,Bare-metallic-electrode Glow Discharges

Radio-frequency (RF), atmospheric-pressure glow discharge (APGD) plasmas with bare metallic electrodes have promising prospects in the fields of plasma-aided etching, deposition, disinfection and sterilization, etc. In this paper, an induced gas discharge approach is proposed for obtaining the RF, atmospheric-pressure, γ-mode, glow discharges with pure nitrogen or air as the primary plasma-working gas using bare metallic electrodes. The discharge characteristics, including the discharge mode, the breakdown voltage and discharge voltage for sustaining α mode and/or γ mode discharges, of the RF APGD plasmas of helium, argon, nitrogen, air or their mixtures using a planar-type plasma generator are presented in this study. The uniformity (no filaments) of the discharges is confirmed by the images taken by an iCCD with a short exposure time (10 ns). The effects of different gap spacings and electrode materials on the discharge characteristics, the variations of the sheath thickness and the electron number density are also studied in this paper.     

Strong spin-orbit effects in small Pt clusters: geometric structure, magnetic isomers and anisotropy

Ab initio density functional calculations including spin-orbit coupling (SOC) have been performed for Pt(n), n = 2-6 clusters. The strong SOC tends to stabilize planar structures for n = 2-5, whereas for clusters consisting of six atoms, three-dimensional structures remain preferred. SOC leads to the formation of large orbital magnetic moments and to a mixing of different spin states. Due to the spin-mixing the total magnetic moment may be larger or smaller than the spin moment in the absence of SOC. Both spin and orbital moments are found to be anisotropic. Because of the strong SOC the energy differences between coexisting magnetic isomers can be comparable to or even smaller than their magnetic anisotropy energies. In this case the lowest barrier for magnetization reversal can be determined by a magnetic isomer which is different from the ground state configuration.     

Features of the Current Sustainment in a Low-Current Discharge in Airflow

The paper relates to the investigations of a low-current discharge in a vortex airflow with the electrode configuration corresponding to classical coaxial plasmatron. The gas flow rate is varied from 0.1 to 0.3 g/s at an inner diameter of the plasmatron nozzle of 5 mm. The discharge is powered by dc voltage via a ballast resistor. Typical averaged current is changed from 0.06 to 0.15 A so that a maximum averaged power dissipated in the discharge amounts to 160 W. In these conditions, a luminous gas region at the plasmatron exit, which in most publications is associated with a plasma jet, is observed. The method for the jet diagnostics based on a usage of the additional electrodes at the plasmatron exit has been proposed. The main idea of the experiments is the elucidation of the problem whether the jet actually represents the plasma area or we have to apply the term “plasma” with care. In particular, in the case under discussion the main charged particles in the jet are electrons that are emitted from a plasma column located in the plasmatron nozzle. The model that describes the formation of electron flow in the jet has been proposed. Typical electron density in the jet estimated with a usage of the model is at a level of 10⁹ cm^?3.

     

Precise determination of manganese in steel by dc glow discharge optical emission spectrometry associated with voltage modulation technique

A voltage modulation technique was applied for the precise and accurate determination of manganese in steels in dc glow discharge optical emission spectrometry. Emission signals from the glow discharge plasma are modulated by a cyclic variation of the discharge voltage so that only the desired signals can be detected at very low noise levels by using a lock-in amplifier. Mn determination in low-alloyed steels was performed to estimate the repeatability of the analytical result. For each measurement, the relative standard deviation (R.S.D.) of the intensities of the Mn I 403.08-nm line was ca 0.1% when a steel sample containing 0.329 mass% Mn was employed. Averaging all analytical values, which are obtained in various discharge conditions, yields statistical information on the precision and accuracy of the analytical values obtained. The relative error from the recommended value is calculated to be 0.5%. The R.S.D. over the analytical values is 1.5%, representing the overall analytical performance of this technique.     

Spatially resolved spectroscopic diagnostics of an argon MIP produced by surface wave propagation (Surfatron)

Spatially resolved spectroscopic diagnostics of an argon MIP have been obtained after Abel inversion. The plasma is sustained by surface wave propagation and is working at atmospheric pressure. The inner diameter of the discharge tube has been selected to obtain one stable discharge filament. Electronic excitation temperatures with argon and rotational temperatures of some molecular species (OH and N₂⁺), electron number and metastable densities and absolute values of the continuum emission coefficient have been determined. In contrast to ICPs and DCPs, the origin of the continuum in the visible part of the spectrum cannot be attributed only to radiative recombination.     

脉冲电弧放电电离甲醇溶液制备碳膜的研究

利用脉冲电弧放电电离甲醇溶液在常压下研究了含金刚石成分的碳膜的制备。用扫描电子显微镜(SEM)、傅里叶红外光谱(FT-IR)、激光Raman光谱和X射线衍射(XRD)研究了在确定的基片温度下甲醇浓度以及放电电压等沉积条件对薄膜的形貌和金刚石的合成的影响。研究结果表明：在放电电压低于2kV时，薄膜主要由无序石墨和无定形碳组成。提高放电电压有助于金刚石的合成，在高的放电电压下，降低甲醇溶液浓度有利于提高碳膜中金刚石成分的含量。     

XPS- and AES-investigations of electron and ion beam induced effects on SK16 glass surfaces

Summary Electron beam induced effects in the near surface region of SK16 glass samples (44% SiO₂, 25% B₂O₃, 28% BaO, 3% other) have been studied using Auger electron spectroscopy (AES) with 3 keV primary electrons at different current densities (4.7 mAcm^–2–75 mAcm^–2). It was found that the SiO₂ and B₂O₃ constituents dissociate during electron bombardment to form binding structures which are characteristic for elemental Si and B, respectively. To investigate the influence of the ion beam irradiation on the binding structure, the glass samples were bombarded with Ar⁺ ions of different kinetic energies (0.5 keV–5 keV), followed by XPS analysis. In comparison to the XPS signal of a virgin SK16 surface from a sample fractured in situ under UHV conditions, the FWHM of the photoelectron peaks were found to increase with the bombarding ion energy. Subsequent Auger spectra revealed that the ion bombardment also caused a dissociation of the SiO₂ and B₂O₃ components. Depending on the ion energy, a constant ratio between elemental and oxidized binding form is obtained.     

LiFePO4电极放电曲线的阻抗模拟

建立了磷酸铁锂(LiFePO4)电极材料放电曲线的阻抗模型.将不同倍率放电的电位分为欧姆电位降、电荷转移电位降与扩散阻抗电位降三部分,以电极交流阻抗谱图结合理论分析,推导出不同倍率电极电位的表达式.模拟结果显示,拟合值与实验值吻合较好.     

Spin-orbit coupling of ππ* states in molecules with annelated oxazole ring

Within the framework of the -electron approximation, matrix elements have been calculated for the operator of spin-orbit coupling (SOC) between singlet and triplet terms of oxazole derivatives with condensed naphthalene, quinoline, coumarin, and carbostyryl fragments (24 structures were examined). Values calculated for the SOC have been compared with experimentally measured quantum yields of fluorescence for 15 compounds. It has been established that the values of the SOC matrix elements amount to 0.02–0.03 cm^–1 on the average.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 26, No. 4, pp. 403–406, July–August, 1990.     

Li3V2(PO4)3/C正极材料在不同电压区间的电化学行为及容量衰减原因

采用溶胶-凝胶法制备锂离子电池正极材料Li₃V₂(PO₄)₃/C. 通过恒电流充放电测试、循环伏安(CV)、电化学阻抗谱(EIS)等方法, 研究了Li₃V₂(PO₄)₃/C 在不同电压区间的电化学行为(3.0-4.5 V和3.0-4.8 V). 结果表明, 3.0-4.8 V电压区间的循环性能和倍率性能均不及3.0-4.5 V电压区间的. 3.0-4.5 V区间0.1C (1C=150mA·g^-1)倍率首次放电比容量为127.0 mAh·g^-1, 循环50次后容量保持率为99.5%, 而3.0-4.8 V区间的分别为168.2 mAh·g^-1和78.5%. 经过高倍率测试后再回到0.1C倍率充放电, 3.0-4.5 V和3.0-4.8 V的放电比容量分别为初始0.1C倍率的99.0%和80.7%. 经过3.0-4.8 V电压区间测试后, 少部分第三个锂离子能够在低于4.5V的电压脱出, 使3.0-4.5 V电压区间的放电比容量提升了7.4%. CV结果表明3.0-4.8 V区间的容量损失主要表现为第一个锂离子的不可逆损失. 极片的X射线衍射(XRD)和X射线光电子能谱(XPS)分析测试结果表明经过3.0-4.8 V测试后, Li₃V₂(PO₄)₃的结构发生了轻微的改变. 电感耦合等离子体(ICP)测试结果表明循环后的电解液中含有少量的V. 结构变形和V溶解可能是Li₃V₂(PO₄)₃在3.0-4.8 V区间容量衰减的主要原因.     

Analytical performance of a radiofrequency-powered glow discharge excitation source associated with bias voltage modulation

A 13.56-MHz Grimm-type glow discharge plasma on which external d.c. voltages are superimposed is investigated for the application to optical emission spectrometry. With a voltage modulation technique associated with phase-sensitive detection, the emission intensities can be measured at very low noise levels, enabling the detection power to be improved. The experimental parameters: d.c. voltage, modulation frequency, and Ar pressure, are investigated for obtaining the optimum conditions. It is possible to obtain a detection limit (Cu I 327.40 nm) of 8 × 10^–4 wt.% for Cu in Fe-based alloys, while 6.6 × 10^–3 wt.% in the case of conventional detection. Received: 3 August 1998 / Revised: 21 September 1998 / Accepted: 24 September 1998     

Constitutive Expression and Optimization of Nutrients for Streptokinase Production by <Emphasis Type="Italic">Pichia pastoris</Emphasis> Using Statistical Methods

The Pichia pastoris clone producing streptokinase (SK) was optimized for its nutritional requirements to improve intracellular expression using statistical experimental designs and response surface methodology. The skc gene was ligated downstream of the native glyceraldehyde 3-phosphate dehydrogenase promoter and cloned in P. pastoris. Toxicity to the host was not observed by SK expression using YPD medium. The transformant producing SK at level of 1,120 IU/ml was selected, and the medium composition was investigated with the aim of achieving high expression levels. The effect of various carbon and nitrogen sources on SK production was tested by using Plackett–Burman statistical design and it was found that dextrose and peptone are the effective carbon and nitrogen sources among all the tested. The optimum conditions of selected production medium parameters were predicted using response surface methodology and the maximum predicted SK production of 2,136.23 IU/ml could be achieved with the production medium conditions of dextrose (x1), 2.90%; peptone (x2), 2.49%; pH, 7.2 (x3), and temperature, 30.4 (x4). Validation studies showed a 95% increase in SK production as compared to that before optimization at 2,089 IU/ml. SK produced by constitutive expression was found to be functionally active by plasminogen activation assay and fibrin clot lysis assay. The current recombinant expression system and medium composition may enable maximum production of recombinant streptokinase at bioreactor level.     

Analytical performance of a radiofrequency-powered glow discharge excitation source associated with bias voltage modulation

A 13.56-MHz Grimm-type glow discharge plasma on which external d.c. voltages are superimposed is investigated for the application to optical emission spectrometry. With a voltage modulation technique associated with phase-sensitive detection, the emission intensities can be measured at very low noise levels, enabling the detection power to be improved. The experimental parameters: d.c. voltage, modulation frequency, and Ar pressure, are investigated for obtaining the optimum conditions. It is possible to obtain a detection limit (Cu I 327.40 nm) of 8 × 10^–4 wt.% for Cu in Fe-based alloys, while 6.6 × 10^–3 wt.% in the case of conventional detection. Received: 3 August 1998 / Revised: 21 September 1998 / Accepted: 24 September 1998