Crystallization kinetics and morphology of poly(butylene succinate‐co‐adipate)

The crystallization kinetics of biodegradable poly(butylene succinate‐co‐adipate) (PBS/A) copolyester was investigated by using differential scanning calorimetry (DSC) and polarized optical microscopy (POM), respectively. The Avrami and Ozawa equations were used to analyze the isothermal and nonisothermal crystallization kinetics, respectively. By using wide‐angle X‐ray diffraction (WAXD), PBS/A was identified to have the same crystal structure with that of PBS. The spherulitic growth rates of PBS/A measured in isothermal conditions are very well comparable with those measured by nonisothermal procedures (cooling rates ranged from 0.5 to 15 °C/min). The kinetic data were examined with the Hoffman–Lauritzen nucleation theory. The observed spherulites of PBS/A with different shapes and textures strongly depend on the crystallization temperatures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3231–3241, 2005     

Time‐resolved crystallization study of absorbable polymers by synchrotron small‐angle X‐ray scattering

Changes in the lamellar morphology that occurred during the quiescent isothermal crystallization of absorbable poly(p‐dioxanone) (PDS) and PDS/poly(glycolide) block copolymer were studied by synchrotron small‐angle X‐ray scattering. Important morphological parameters such as the lamellar long period, the thicknesses of the crystal and amorphous phases, and the scattering invariant were estimated as a function of time, and trends observed over a wide range of experimental conditions are discussed. Thicker but more perfect lamellae were detected at higher crystallization temperatures. The breadth of the normalized semilog Lorentz‐corrected intensity peak systematically decreased with increasing temperature. In addition, the values of the crystallization half‐time and the Avrami exponent (n = 2.5), determined from the real‐time changes in the lamellar development, showed superb agreement with the bulk crystallinity data generated from other experimental techniques, such as calorimetry and dielectric relaxation spectroscopy. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 153–167, 2001     

Crystallization,morphology, and thermal behavior of poly(p‐phenylene sulfide)

This article deals with the structure, crystallization, morphology, and thermal behavior of poly(p‐phenylene sulfide) (PPS) with low‐molecular mass, probed by DSC, optical, and electron microscopy. The growth rates of spherulites were measured over the temperature range 235–275°C. A regime II–III transition was found at T = 250°C. The regime transition was accompanied by a morphological change from sheaflike structure to classical spherulites. The Avrami equation poorly described the isothermal crystallization of PPS, for the occurrence of mixed growth mechanisms and secondary crystallization, in agreement with the morphology and the thermal behavior. Two melting peaks were detected on DSC curves and attributed to the melting of crystals formed isothermally at T_c by primary and secondary crystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 415–424, 2001     

Comparison of different nucleating agents on crystallization of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerates)

In this study, thymine and melamine were introduced as nucleating agents for poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerates) (PHBVs) and poly(3‐hydroxybutyrate) (PHB), and their effects were compared with that of boron nitride (BN). Because the overall crystallization rate of PHBVs decreases significantly with the increase in the 3‐hydroxyvalerate comonomer content, the study focused on the crystallization of PHBVs. Isothermal crystallization kinetics of the neat PHBVs and the nucleated PHBVs were studied by differential scanning calorimetry (DSC). The Avrami equation was derived and the parameters were assessed for the nucleation and crystal growth mechanism. The nucleation and crystal growth were examined using polarized optical microscopy. All nucleating agents had similar particle sizes and showed good dispersion in the polymer matrix, as revealed by scanning electron microscopy. The results indicated that BN and thymine significantly increased the overall crystallization rate for all PHBVs studied and demonstrated very similar nucleating effects. Melamine reacted with PHBVs and accelerated the thermal degradation, and hence was less effective in nucleating PHBVs. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1564–1577, 2007     

Crystallization kinetics for low‐ether‐content polyether–polyester block copolymers with amide linkages

A series of low‐ether‐content polyether–polyester block copolymers with amide linkages were synthesized. Their crystallization kinetics and mechanisms were investigated. The crystallization kinetics were analyzed via Avrami treatment; an average value of 1.8 for the Avrami index was thus obtained. Athermal nucleation was evidenced by observations of a linear boundary between impinged spherulites under polarized light microscopy and transmission electron microscopy. The development of spherulitic morphology with a hedgehog texture was attributed to the mechanism of lamellar branching. On the basis of the morphological observations and Avrami analysis, a crystallization mechanism through a heterogeneous nucleation process with homogeneous lamellar branching was proposed. No regime transition was found for polyether–polyesters in the examined temperature ranges, and the crystallization was identified as regime I kinetics on the basis of a Lauritzen Z test. The copolymerization of poly(ether amide)s with polyesters led to a significant suppression of the crystallization rate of polyester crystals. The suppression was explained as the result of a dilution effect in nucleation combined with an increasing nucleation barrier. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2469–2480, 2001     

Nonisothermal crystallization studies on poly(4‐hydroxybutyric acid‐alt‐glycolic acid)

The crystallization behavior of a new sequential polyester constituted by glycolic acid and 4‐hydroxybutyric acid has been studied under nonisothermal conditions. Nonisothermal melt crystallization has been followed by means of hot‐stage optical microscopy (HSOM), with experiments performed at different cooling rates. Two crystallization regimes have been found, which is in good agreement with previous isothermal studies and with the different spherulitic morphologies that were observed. The kinetics of both glass and melt crystallizations has also been studied by differential scanning calorimetry (DSC) and considering the typical Avrami, Ozawa, and Cazé analyses. Only the last gave Avrami exponents, which were in good agreement with those measured under isothermal conditions, suggesting a spherulitic growth with a predetermined nucleation. Isoconversional data of melt and glass nonisothermal crystallizations have been combined to obtain the Hoffman and Lauritzen parameters. Results again indicate the existence of two crystallization regimes with nucleation constants close to those deduced from isothermal DSC experiments. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 121–133, 2008     

A new route of manipulation of poly(L‐lactic acid) crystallization by self‐assembly of p‐tert‐butylcalix[8]arene and toluene

A novel nucleating agent (TBC8‐t), self‐assembled with p‐tert‐butylcalix[8]arene (TBC8) and toluene, was used to manipulate the crystallization behavior of poly(L ‐lactic acid) (PLLA). Toluene molecules were used to adjust the crystallization structure of TBC8. Differential scanning calorimetry results show that the crystallization peak temperature (T_c) and crystallization rate (ΔH_c/time) of PLLA nucleated with TBC8‐t are 132.3 °C and 0.24 J/gs, respectively, which are much higher than that with conventional nucleating agent‐talc (T_c = 119.3 °C, ΔH_c/time = 0.13 J/gs). The results of polarized optical microscopy demonstrate that TBC8‐t could greatly enhance the crystallization rate of PLLA by increasing the nucleation rate rather than crystal growth rate. Along with an improvement of the crystallization rate, the crystalline morphology of PLLA is also affected by TBC8‐t. The addition of TBC8‐t transforms most of the original spherulite crystals into sheaf‐like crystals. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1235–1243, 2010     

Isothermal crystallization kinetics and spherulitic morphology of poly(4‐hydroxybutyric acid‐alt‐glycolic acid)

Isothermal crystallization behavior of a new regular polyester constituted by glycolic acid and 4‐hydroxybutyric acid units is studied by means of differential scanning calorimetry and hot‐stage optical microscopy. A wide range of crystallization conditions were experimentally accessible, allowing various morphological features to be observed and accurate estimates made of characteristic growth parameters, including radial growth and nucleation rates. Three‐dimensional spherulitic growth from heterogeneous nuclei is deduced from the Avrami analysis, whereas optical micrographs reveal two different spherulitic textures that agree with the existence of two crystallization regimes. These can be well distinguished from the breaks observed in the Lauritzen and Hoffman plots when the linear crystal growth rate or the overall crystallization rate is considered. Ringed and nonringed spherulites with negative and positive birefringence, respectively, can be obtained depending on crystallization conditions and regimes. The studied polyester shows rather complex melting behavior which is interpreted in terms of a recrystallization process involving the two different kinds of spherulites. This study allows polymorphism to be discounted. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2640–2653, 2007     

Fluctuation‐assisted crystallization of an iPP/PEOc polymer alloy prepared on a single multicatalyst reactor granule

The new fluctuation‐assisted mechanism for nucleation and crystallization in the isotactic polypropylene/poly(ethylene‐co‐octene) alloy has been studied. We found that the liquid–liquid phase separation (LLPS) had a dominant influence on the crystallization kinetics through the nucleation process. After LLPS, the nucleation of crystallization mainly occurred at the interface of the phase‐separated domains. It is because that the concentration fluctuations of the LLPS induced the motion of polymer chains and possibly some segmental alignment and/or orientation in the concentration gradient regions through interdiffusion, which could assist the formation of nuclei for crystallization. In other words, the usual nucleation energy barrier could be overcome (or at least partially) by the concentration fluctuation growth of LLPS in the unstable regions. This could be viewed as a new kind of heterogeneous nucleation and could be an addition to the regular nucleation and growth mechanism for crystallization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 166–172, 2009     

Melting behavior,crystallization kinetics,and crystal structure of poly(2‐hydroxyethoxybenzoate)

The melting behavior and crystallization kinetics of poly(2‐hydroxyethoxybenzoate) (PHEBA) were investigated with differential scanning calorimetry and hot‐stage optical microscopy. The observed multiple endotherms, commonly displayed by polyesters, were influenced by the crystallization temperature. By the application of the Hoffman–Weeks method to the melting temperatures of isothermally crystallized samples, a value of 232 °C was obtained for the equilibrium melting temperature. Isothermal crystallization kinetics were analyzed according to Avrami's treatment. Values of Avrami's exponent n close to 3 were obtained, independently of the crystallization temperature, in agreement with a crystallization process originating from predetermined nuclei and characterized by three‐dimensional spherulitic growth. In fact, space‐filling banded spherulites were observed by hot‐stage optical microscopy at all crystallization temperatures explored, with the band spacing increasing with increasing crystallization temperature. The rate of crystallization became lower as the crystallization temperature increased as usual at low undercooling, with the crystallization process controlled by nucleation. The equilibrium heat of fusion was determined by differential scanning calorimetry and wide‐angle X‐ray scattering measurements. Finally, the crystal phase of PHEBA was investigated with wide‐angle X‐ray scattering, and a triclinic unit cell was hypothesized. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1354–1362, 2002     

Isothermal crystallization behavior of exfoliated‐PP/IMMT nanocomposites via in situ polymerization

Highly exfoliated isotactic‐polypropylene/alkyl‐imidazolium modified montmorillonite (PP/IMMT) nanocomposites have been prepared via in situ intercalative polymerization. TEM and XRD results indicated that the obtained composites were highly exfoliated PP/IMMT nanocomposites and the average thickness of IMMT in PP matrix was less than 10 nm, and the distance between adjacent IMMT particles was in the range of 20–200 nm. The isothermal crystallization kinetics of highly exfoliated PP/IMMT nanocomposites were investigated by using differential scanning calorimeter(DSC) and polarized optical microscope (POM). The crystallization half‐time t_1/2, crystallization peak time t_max, and the Avrami crystallization rate constant K_n showed that the nanosilicate layers accelerate the overall crystallization rate greatly due to the nucleation effect, and the crystallization rate was increased with the increase in MMT content. Meanwhile, the crystallinity of PP in nanocomposites decreased with the increase in clay content which indicated the PP chains were confined by the nanosilicate layers during the crystallization process. Although the well‐dispersed silicate layers did not have much influence on spherulites growth rate, the nucleation rate and the nuclei density increased significantly. Accordingly, the spherulite size decreased with the increase in MMT content. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2215–2225, 2009     

Crystallization kinetics of PGBG4: A sequential poly(ester amide) derived from glycine, 1,4‐butanediol,and adipic acid

Isothermal crystallization kinetics of a new sequential poly(ester amide) derived from glycine, 1,4‐butanediol, and adipic acid was investigated with differential scanning calorimetry and optical microscopy. The Avrami analysis was performed to obtain the kinetic parameters of primary and secondary crystallization. The experimental data indicate a heterogeneous nucleation with spherical growth geometry for the primary crystallization, whereas a linear growth within formed spherulites is characteristic of the last crystallization stages. The Lauritzen–Hoffman analysis was also undertaken to determine the different crystallization regimes, having estimated the corresponding nucleation constants. Temperature dependence of the normalized crystallization‐rate constants was tested with different theoretical equations. These allow an estimation of a temperature close to 90 °C for the maximum crystallization rate. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 903–912, 2003     

Inorganic–organic hybrids involving poly(ε‐caprolactone) and silica network: Hydrogen‐bonding interactions and isothermal crystallization kinetics

Inorganic–organic hybrids mediated by hydrogen‐bonding interactions involving silicon oxide network and poly(ε‐caprolactone) (PCL) were prepared via an in situ sol–gel process of tetraethoxysilane in the presence of PCL. Fourier transform infrared spectroscopy indicated that there were hydrogen‐bonding interactions between carbonyls of PCL and silanol hydroxyls that were formed by incomplete polycondensation in the sol–gel process. In terms of the frequency shift of the hydroxyl stretching vibration bands, it is concluded that the strength of the interassociation between PCL and silicon oxide networks is weaker than that of the self‐association in the control silica network. The phenomenon of equilibrium melting point depression was observed for the PCL/silica system. The hybridization of PCL with silica network causes a considerable increase in the overall crystallization rate and dramatically influences the mechanism of nucleation and growth of the PCL crystallization. The analysis of isothermal crystallization kinetic data according to the Hoffman‐Lauritzen theory shows that with increasing silica content in the hybrids, the surface energy of extremity surfaces increases dramatically for the hybrids. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2594–2603, 2005     

Crystallization kinetics study of poly(L‐lactic acid)/carbon nanotubes nanocomposites

Effects of carbon nanotubes (CNT) on the isothermal crystallization kinetics of poly(L ‐lactic acid) (PLLA) were quantitatively investigated using the Avrami equation and the secondary nucleation theory of Lauritzen and Hoffman. CNT via grafting modification with PLLA could well disperse in the PLLA matrix and give significantly enhanced crystallization rate and crystallinity of PLLA as analyzed by differential scanning calorimetry and polarized optical microscopy. Analysis of isothermal crystallization kinetics using the Avrami equation demonstrated that CNT significantly enhanced the bulk crystallization of PLLA. Analysis of spherulite growth kinetics using the secondary nucleation theory of Lauritzen and Hoffman found that CNT could expand the temperature range of the crystallization regime III of PLLA. Values of the nucleation constant (K_g) in crystallization regimes III and II of PLLA both increased with increasing CNT contents. The K_g III/K_g II ratios were found to be close to the theoretical value 2 but were not clearly found to depend on the CNT contents. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 983–989, 2010     

Crystallization and morphology of poly(ethylene oxide‐b‐lactide) crystalline–crystalline diblock copolymers

The crystallization behaviors and morphology of asymmetric crystalline–crystalline diblock copolymers poly(ethylene oxide‐lactide) (PEO‐b‐PLLA) were investigated using differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and microscopic techniques (polarized optical microscopy (POM) and atomic force microscopy (AFM)). Both blocks of PEO₅‐b‐PLLA₁₆ can be crystallized, which was confirmed by WAXD, while PEO block in PEO₅‐b‐PLLA₃₀ is difficult to crystallize because of the confinement induced by the high glass transition temperature and crystallization of PLLA block with the microphase separation of the block copolymer. Comparing with the crystallization and morphology of PLLA homopolymer and differences between the two copolymers, we studied the influence of PEO block and microphase separation on the crystallization and morphology of PLLA block. The boundary temperature (T_b) was observed, which distinguishes the crystallization into high‐ and low‐temperature ranges, the growth rate and morphology were quite different between the ranges. Crystalline morphologies including banded spherulite, dendritic crystal, and dense branching in PEO₅‐b‐PLLA₁₆ copolymer were formed. The typical morphology of dendritic crystals including two different sectors were observed in PEO₅‐b‐PLLA₃₀ copolymer, which can be explained by secondary nucleation, chain growth direction, and phase separation between the two blocks during the crystallization process. Lozenge‐shaped crystals of PLLA with screw dislocation were also observed employing AFM, but the crystalline morphology of PEO block was not observed using microscopy techniques because of its small size. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1400–1411, 2008     

Transient and athermal effects in the crystallization of polymers. I. Isothermal crystallization

The isothermal crystallization of poly(propylene) and poly(ethylene terephthalate) was investigated with differential scanning calorimetry and optical microscopy. It was found that the induction time depends on the cooling rate to a constant temperature. The isothermal crystallization of the investigated polymers is a complex process and cannot be adequately described by the simple Avrami equation with time‐independent parameters. The results indicate that crystallization is composed of several nucleation mechanisms. The homogeneous nucleation occurring from thermal fluctuations is preceded by the nucleation on not completely melted crystalline residues that can become stable by an athermal mechanism as well as nucleation on heterogeneities. The nucleation rate depends on time, with the maximum shortly after the start of crystallization attributed to nucleation on crystalline residues (possible athermal nucleation) and on heterogeneities. However, the spherulitic growth rate and the exponent n do not change with the time of crystallization. The time dependence of the crystallization rate corresponds to the changes in the nucleation rate with time. The steady‐state crystallization rate in thermal nucleation is lower than the rate determined in a classical way from the half‐time of crystallization. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1835–1849, 2002     

Effect of α‐cyclodextrin on the crystallization of poly (3‐hydroxybutyrate)

The effect of α‐cyclodextrin (α‐CD) on the crystallization behavior of poly(3‐hydroxybutyrate) (PHB) was investigated with polarized optical microscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. We found that the addition of α‐CD can greatly accelerate the crystallization of PHB and that α‐CD has a potential not only to enhance the nucleation but also to accelerate the crystallization of PHB. Compared to a conventional nucleation agent, such as talc, α‐CD is a natural product and has many advantages because it is environmentally friendly and safe to humans. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3461–3469, 2004     

Nonisothermal crystallization behavior of poly(butylene adipate‐co‐terephthalate)/clay nano‐biocomposites

The study of the nonisothermal crystallization behavior of layered silicates micro‐ and nano‐biocomposites based on poly(butylene adipate‐co‐terephthalate) (PBAT), a biodegradable copolyester, has been carried out with different theoretical models. They were applied and developed with the aim to describe and better understand the influence of the layered silicates dispersion on crystallization. The nucleation efficiency of the layered silicates has been demonstrated with the use of the “Modified Avrami model,” thanks to the higher crystallization rate parameter, Z_c, and of the lower crystallization half‐time, t_1/2, compared to the neat matrix. The crystallization activation energies, E_a, calculated from “Kissinger's model” have shown that layered silicates have a negative effect on the crystallite growth process. Thus, these analyses have shown that layered silicates have a double effect on the crystallization process. These two opposites' phenomena depend on the dispersion quality and are more pronounced for the intercalated nano‐biocomposites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1503–1510, 2007     

Crystallization kinetics and morphology of biodegradable poly(butylene succinate‐co‐propylene succinate)s

The crystallization behavior of biodegradable poly(butylene succinate) and copolyesters poly(butylene succinate‐co‐propylene succinate)s (PBSPS) was investigated by using ¹H NMR, DSC and POM, respectively. Isothermal crystallization kinetics of the polyesters has been analyzed by the Avrami equation. The 2.2‐2.8 range of Avrami exponential n indicated that the crystallization mechanism was a heterogeneous nucleation with spherical growth geometry in the crystallization process of polyesters. Multiple melting peaks were observed during heating process after isothermal crystallization, and it could be explained by the melting and recrystallization model. PBSPS was identified to have the same crystal structure with that of PBS by using wide‐angle X‐ray diffraction (WAXD), suggesting that only BS unit crystallized while the PS unit was in an amorphous state. The crystal structure of polyesters was not affected by the crystallization temperatures, too. Besides the normal extinction crosses under the POM, the double‐banded extinction patterns with periodic distance along the radial direction were also observed in the spherulites of PBS and PBSPS. The morphology of spherulites strongly depended on the crystallization temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 420–428, 2007     

Nucleation effect of cyclodextrin inclusion complexes on the crystallization of isotactic poly(1‐butene)

The β‐cyclodextrin (β‐CD) and γ‐cyclodextrin (γ‐CD) inclusion complexes (ICs) with four kinds of polyolefin were prepared. The crystallization behavior of isotactic poly(1‐butene) (iPB‐1) blended with these CDs and ICs was investigated by differential scanning calorimetry, polarized optical microscopy, and wide‐angle X‐ray diffraction. The iPB‐1 blended with the ICs was found to exhibit higher crystallization temperature (T_C), smaller spherulites, and faster crystallization rate than neat iPB‐1. These results indicate that the ICs can act as nucleating agent on the crystallization of iPB‐1 and induce the accelerated crystallization. The guest molecules of ICs play an important role in the nucleation effect of ICs on the crystallization of iPB‐1. ICs with polyolefin having higher T_C as guest molecules have higher nucleation effect than the one with polyolefin having lower T_C as guest molecules. And, the CDs and ICs induce different crystal form of iPB‐1. The crystal of iPB‐1 blended with CDs is defective, whereas the crystal of iPB‐1 blended with ICs is more perfect. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 389–395, 2010