Determination of 4-methylbenzilidene camphor in sunscreen by square wave voltammetry in media of cationic surfactant

The voltammetric behavior of 4-methylbenzelidene camphor (MBC) was studied by square wave voltammetry (SWV) using mercury electrode. The experimental condition that provided the highest peak current with the best reduction signal definition of MBC was found in Britton-Robinson buffer and cationic surfactants, cetyltrimethylammoniun bromide (CTABr). A single peak of MBC reduction was observed at − 1.21 V versus Ag/AgCl. The developed methodology was applied for determination of MBC in commercial sunscreen SPF 15, 20 and 30 and for the simultaneous determination when other protection agents were associated, such as benzophenone-3 (BENZO) and octyl methoxycinammate (OMC). Both methodologies had shown good determination values for the analyzed samples. The calculated detection limit was 2.99 × 10^− 9 mol L^− 1 and the quantification limit was 9.98 × 10^− 9 mol L^− 1.     

Sequential Voltammetric Determination of Uranium,Cadmium and Lead by Using the ex situ Bismuth Film Electrode: Application to Phosphate Fertilizers

A sequential voltammetric procedure for the determination of uranium, cadmium and lead was investigated at an ex situ bismuth film electrode (BiFE). First, the adsorptive stripping voltammetry was applied to assay the U(VI)‐cupferron complex in the differential pulse mode (detection limit of 1.0 µg L^?1, 200 s accumulation time). Through the manipulation of the same aliquot of the sample, efforts were made to quantify cadmium and lead by square wave anodic stripping voltammetry. Detection limits of 2.03 µg L^?1 for Cd (II) and 2.43 µg L^?1 for Pb (II) were calculated (100 s accumulation time). The methodology was successfully applied to phosphate fertilizer samples after open vessel wet decomposition (HNO₃/H₂O₂). The following value ranges were evaluated: U (VI) 37.2–150 mg kg^?1, Pb (II) 78.3–204 mg kg^?1 and Cd (II) 44.1–71.6 mg kg^?1. Validation was performed by using the standard reference materials SRM‐695 – phosphate fertilizer – and SRM‐1643e – water.     

Voltammetric Determination of 4‐Nitrophenol and 5‐Nitrobenzimidazole Using Different Types of Silver Solid Amalgam Electrodes – A Comparative Study

The voltammetric behavior of two genotoxic nitro compounds (4‐nitrophenol and 5‐nitrobenzimidazole) has been investigated using direct current voltammetry (DCV) and differential pulse voltammetry (DPV) at a polished silver solid amalgam electrode (p‐AgSAE), a mercury meniscus modified silver solid amalgam electrode (m‐AgSAE), and a mercury film modified silver solid amalgam electrode (MF‐AgSAE). The optimum conditions have been evaluated for their determination in Britton‐Robinson buffer solutions. The limit of quantification (L_Q) for 5‐nitrobenzimidazole at p‐AgSAE was 0.77 µmol L^?1 (DCV) and 0.47 µmol L^?1 (DPV), at m‐AgSAE it was 0.32 µmol L^?1 (DCV) and 0.16 µmol L^?1 (DPV), and at MF‐AgSAE it was 0.97 µmol L^?1 (DCV) and 0.70 µmol L^?1 (DPV). For 4‐nitrophenol at p‐AgSAE, L_Q was 0.37 µmol L^?1 (DCV) and 0.32 µmol L^?1 (DPV), at m‐AgSAE it was 0.14 µmol L^?1 (DCV) and 0.1 µmol L^?1 (DPV), and at MF‐AgSAE, it was 0.87 µmol L^?1 (DCV) and 0.37 µmol L^?1 (DPV). Thorough comparative studies have shown that m‐AgSAE is the best sensor for voltammetric determination of the two model genotoxic compounds because it gives the lowest L_Q, is easier to prepare, and its surface can be easily renewed both chemically (by new amalgamation) and/or electrochemically (by imposition of cleaning pulses). The practical applicability of the newly developed methods was verified on model samples of drinking water.     

基于酞菁铜衍生物为载体的电极对水杨酸根的选择性电位响应

本文以2,9,16,23-四硝基酞菁铜(II) (Cu(II)TNPc) 和2,9,16,23-四氨基酞菁铜(II) (Cu(II)TAPc) 为载体制备PVC聚合膜,构建了水杨酸根选择性电极,并探讨了该电极的选择性响应性能。研究了增塑剂的性质、载体的含量及阴、阳离子添加剂对电极电位响应的影响。结果表明,基于Cu(II)TNPc为载体的PVC膜电极对水杨酸根 (Sal－) 呈现出优先选择性电位响应。具有最佳电位响应的电极的膜组成是：(w/w) 3.0% Cu(II)TNPc,67.0% o-NPOE,29.5% PVC和0.5% NaTPB。基于该组成的电极的线性响应范围为1.0×10－1－9.0×10－7 mol·L－1,检测下限为7.2×10－7 mol·L-1,斜率为－59.8±0.5 mV/decade;其响应快速,稳定性好,适宜的pH范围是3.0－7.0。并成功运用于了实际样品中水杨酸含量的测定,获得令人满意的结果。     

Determination of Sulfite in Hair Waving Products Using Oxygen‐Incorporated Gold‐Modified Screen‐Printed Electrodes

An electrodeposition oxygen‐incorporated gold‐modified screen‐printed carbon electrode (AuOSPE) was fabricated to determine the sulfite content in hair waving products. The AuOSPE showed an electrocatalytic current for sulfite at +0.4 V (vs. Ag/AgCl). Compared with a gold screen‐printed electrode (AuSPE), the AuOSPE showed a higher electrocatalytic current. The increase in the electrocatalytic current was ascribed to the increase of the oxygen incorporated with gold atom on AuOSPE. The AuOSPE coupled with a flow injection analysis (FIA) system showed excellent oxidation current for sulfite in a 0.1 mol L^?1 phosphate buffer solution (PBS), pH 6.0. The linear working range for determining the sulfite content was 0.05 to 1200 mg L^?1 (0.625 µmol L^?1 to 15.00 mmol L^?1) with a calculated detection limit of 0.03 mg L^?1 (0.375 µmol L^?1) (DL, S/N=3). Relative standard deviations (RSD) of 3.03 %, 2.30 % and 4.26 % were calculated for consecutive injections (n=12) of 20, 300 and 900 mg L^?1 sulfite, respectively. The amount of sulfite in two hair waving products was determined by the proposed method and a standard iodometric method. The recoveries ranged from 96.18 % to 105.61 %. The AuOSPE showed high sensitivity, selectivity, stability and reproducibility for sulfite.     

Simultaneous quantitative estimation of oxybenzone and 2-ethylhexyl-4-methoxycinnamate in sunscreen formulations by second order derivative spectrophotometry

Simultaneous determination of 2-ethylhexyl-4-methoxycinnamate (OMC) and oxybenzone (OB) in commercial sunscreen formulations has been achieved by using second order derivative spectrophotometry. The analytical methodology described does not require elaborate pretreatment of samples. The results obtained could be validated by reverse phase HPLC assay by using isocratic methanol: water (88: 12) solvent system. The sensitivity of the developed derivative spectrophotometry method was determined to be 9.0 × 10⁻³ L/mg for OB and 9.56 × 10⁻³ L/mg for OMC. The limit of instrumental detection (LOD) was determined to be 0.6 mg/L for OB and 1.38 mg/L for OMC with relative standard deviation of 0.001 and 0.004 for OB and OMC respectively. The method developed can be used for quick assay of commercial sunscreens. The article is published in the original.     

Ultra-trace level determinations of benzidine and dichlorobenzidine residues in surface water by liquid chromatography-electrospray ionization tandem mass spectrometry

A liquid chromatography-electrospray ionization tandem mass spectrometric method (LC-ESI-MS/MS) has been developed for the determination of benzidine (BZ) and 3, 3′-dichlorobenzidine (DCBZ) from surface water. Parent ion of DCBZ gave strong signal with ESI by dissolving with 15?mM ammonium formate, which is also used as mobile phase. Deuterated BZ (d8-BZ) was chosen as the internal standard (IS). BZ and DCBZ were extracted by solid-phase extraction on Oasis hydrophilic-lipophilic balance (HLB) from water at pH 8.0. The coefficients of variation of BZ and DCBZ were less than 13.1% and the detection limits were 0.004?ng?L^?1 for BZ and 0.7?ng?L^?1 for DCBZ using 0.5?L surface water. The detection limit shows fair lower value than the water quality criteria for BZ and DCBZ established by the US EPA. When the proposed method was used to analyze the target compounds in sixteen surface water samples, BZ was detected in a concentration range of 0.15–2.33?ng?L^?1 in four of sixteen surface water samples     

Chemical Speciation of Antimony(III and V) in Water by Adsorptive Cathodic Stripping Voltammetry Using the 4‐(2‐Thiazolylazo) – Resorcinol

A simple adsorptive cathodic stripping voltammetry method has been developed for antimony (III and V) speciation using 4‐(2‐thiazolylazo) – resorcinol (TAR). The methodology involves controlled preconcentration at pH 5, during which antimony(III) – TAR complex is adsorbed onto a hanging mercury drop electrode followed by measuring the cathodic peak current (I_p,c) at ?0.39 V versus Ag/AgCl electrode. The plot of I_p,c versus antimony(III) concentration was linear in the range 1.35×10^?9–9.53×10^?8 mol L^?1.The LOD and LOQ for Sb(III) were found 4.06×10^?10 and 1.35×10^?9 mol L^?1, respectively. Antimony(V) species after reduction to antimony(III) with Na₂SO₃ were also determined. Analysis of antimony in environment water samples was applied satisfactorily.     

Polarographic determination of sunscreen agents in cosmetic products in micellar media

This paper introduces a simple, fast and reliable electroanalytical method for differential-pulse polarography based on electrochemical reduction at a dropping mercury electrode. The method was validated for the determination of 2-ethylhexyl-4-methoxycinnamate (EHMC) alone and in association with 4-methylbenzylidene camphor (MBC) or 2-hydroxy-4-methoxybenzophenone (BENZ-3) in samples of commercial cosmetic preparations. The supporting electrolyte that provided the best-defined and most intense peak current for EHMC determination was Britton-Robinson buffer (pH 4.0) in the presence of a cationic surfactant. Under optimized conditions, EHMC exhibited one single peak of reduction at −1.49 V versus Ag/AgCl. A limit of detection of 3.76 × 10⁻⁸ mol L⁻¹ and a limit of quantitation of 1.25 × 10⁻⁷ mol L⁻¹ were found for the pure EHMC standard. A good average recovery rate was reached for all the samples analyzed.     

Potentiometric Sensing of Aspirin Metabolite in Human Plasma and Pharmaceutical Preparations Using Co(III)‐complex Based Electrodes: Experimental and Quantum Chemical Calculations

Three novel poly vinyl chloride (PVC) ( A ), carbon paste (CP) ( B ), and coated glassy carbon‐MWCNT (CGC) ( C ) salicylate (sal^?) sensors based on new synthesized [Co(L^2Cl)Cl₃(H₂O)] ? H₂O complex (L^2Cl=(1H‐benzimidazol‐2‐ylmethyl)‐N‐(2‐chloro‐phenyl)‐ amine)), o‐nitrophenyloctyl ether as a mediator and tridodecylmethylammonium chloride as a cationic additive were successfully used for determination of sal^? in human plasma and pharmaceutical formulations. The sal^?‐sensors exhibited enhanced sensitivity with slope of ?63.5, ?60.5 and ?58.9 mV/decade and detection limit of 1.0×10^?5, 4.0×10^?7, and 1.0×10^?6 mol L^?1 for A – C sensors respectively. Quantum chemical calculations were carried out by HF and DFT/B3LYP methods to explore and investigate the interaction between the receptor and the different anions. The intermolecular H‐bond created between the uncoordinated C?O of salicylate group and the secondary amino group in the complex is the key factor of the selectivity of the proposed sensor. A linear relation is established between the natural charge on the Co center and the value of the binding energy, where the decrease in positive charge is associated by an increase in the anion binding energy.     

Adsorptive Stripping Determination of Scandium(III) with Mordant Blue 9 on Silver Amalgam Film Electrode

A new adsorptive stripping voltammetric method for the determination of trace scandium(III) based on the adsorption of scandium(III)‐mordant blue 9 complex on the cyclic renewable mercury film silver based electrode (Hg(Ag)FE) is presented. The effects of various factors such as: preconcentration potential and time, pulse height, step potential and supporting electrolyte composition are optimized. The calibration graph is linear from 2 nM (0.09 μg L^?1) to 90 nM (4 μg L^?1) for a preconcentration time of 45 s, with correlation coefficient of 0.9995. For a Hg(Ag)FE with a surface area of 7.9 mm² the detection limit for a preconcentration time of 90 s is as low as 5 ng L^?1. The repeatability of the method at a concentration level of the analyte as low as 0.2 μg L^?1, expressed as RSD is 1.9 % (n=5). The proposed method was successfully applied and validated by studying the certified reference material (CRM 320 – river sediment) and natural samples with simultaneous recovery of Sc(III) from spiked water and sediment samples.     

Electrochemical Behaviour of Carbamazepine in Acetonitrile and Dimethylformamide Using Glassy Carbon Electrodes and Microelectrodes

The electrochemical reduction of carbamazepine in acetonitrile (ACN) and dimethylformamide (DMF) using a glassy carbon electrode and microelectrodes has been studied. The reduction process is consistent with an electrochemical‐chemical mechanism (EC) involving a two electron transfer followed by a first order reaction, as shown by the cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Half‐wave potential, number of electron transferred, diffusion coefficient and rate constant of the associated chemical reaction are reported. Limits of detection (LOD) for DPV are 0.92 and 0.76 µg mL^?1 (3.89×10^?6 mol L^?1 and 3.21×10^?6 mol L^?1) in ACN and DMF, respectively. Precision (%RSD) and recovery (%) values when pharmaceutical compounds (200mg carbamazepine tablets) and spiked plasma samples were tested ranged from 1.09 to 9.04 % and % recoveries ranged from 96 to 104.1 %.     

Determination of phosphate in freshwater samples by flow-injection with lucigenin chemiluminescence

Lucigenin chemiluminescence (CL) in conjunction with flow-injection analysis (FIA) is used for the determination of phosphate in freshwater samples. The procedure is based on the formation of molybdophosphoric heteropoly acid (MoP–HPA) by the reaction of phosphate and ammonium molybdate under acidic conditions. CL emission was observed as a result of oxidation of lucigenin in aqueous sodium hydroxide solution in the presence of MoP–HPA. Calibration was linear up to 500?µg?L^?1 (r ^2?=?0.9998; n?=?8), with a detection limit (S/N?=?3) of 0.95?µg?L^?1. An injection throughput of 120 h^?1, and relative standard deviation (RSD; n?=?4) of 1.3–3.2% were achieved in the concentration range studied. An on-line chelating column was used to remove interfering cations. The method was applied to freshwater samples, and the results (51?±?1.0 – 107?±?2.0?µg?L^?1) did not differ significantly from results obtained using a spectrophotometric method (52.5?±?1.0 – 102?±?2.0?µg?L^?1) at 95% confidence level (t-test).     

Modified Carbon Paste Electrode for Kinetic Investigation and Simultaneous Determination of Ascorbic and Uric Acids

The present work explores, for the first time, the electrocatalytic oxidation of ascorbic acid (AscH₂) and its determination in the presence of uric acid (UA) on the in situ activated 4‐nitrophthalonitrile modified carbon paste electrode. The kinetic constant κ for the catalytic reaction for the electrocatalytic oxidation of ascorbic acid, evaluated by cyclic voltammetry, chronoamperometry and RDE voltammetry provided values around 10⁶ L mol^?1 s^?1. The sensor provided a linear response range for AscH₂ and UA from 5.0 up to 120.0 μmol L^?1 with detection limits of 1.6 μmol L^?1and 1.3 μmol L^?1, respectively. The sensor was applied for the simultaneous determination of AscH₂ and UA in urine samples and the average recoveries for these samples were 99.8 (±3.1)% and 99.9 (±2.1)%, respectively .     

Voltammetric Sensor for Sodium Nitroprusside Determination in Biological Fluids Using Films of Poly‐L‐Lysine

Sodium nitroprusside (NP), a commercial vasodilator, can be pre‐concentrated on vitreous carbon electrode modified by films of 97.5%: 2.5% poly‐L ‐lysine (PLL): glutaraldehyde (GA). This coating gives acceptable anion exchange properties whilst giving the required improvement of adhesion to the glassy carbon electrode surface. Linear response range and detection limit on nitroprusside in B‐R buffer pH 4.0, were 1×10^?6 to 2×10^?5 mol L^?1 and 1×10^?7 mol L^?1, respectively. The repeatability of the proposed sensor, evaluated in term of relative standard deviation, was measured as 4.1% for 10 experiments. The voltammetric sensor was directly applied to determination of nitroprusside in human plasma and urine samples and the average recovery for these samples was around 95–97% without any pre treatment.     

Kinetic Determination of Uric Acid in Human Serum by Using the Uncatalyzed BZ Reaction in Non‐equilibrium Steady State

A novel kinetic method for determination of uric acid in human serum by means of an uncatalyzed BZ system consisting of potassium bromate and p‐hydroxybenzaldehyde (p‐HBA) in sulfuric acid medium was proposed, in which the analyte perturbation to the system was recorded close to the bifurcation point. The potential change was directly proportional to the logarithm of concentration of uric acid in the range of 3.73×10^?8–7.48×10^?4 mol·L^?1 (r=0.9983) with a detection limit of 7.45×10^?9 mol·L^?1 and a recovery from 98.9% to 101.1%. A comparison between the proposed technique and other methods indicated that results obtained were in agreement with those in clinical detection. In addition, the possible mechanism of action of uric acid on the uncatalyzed BZ reaction was also discussed briefly.     

Determination of carbendazim and thiabendazole in apple juice by hollow fibre-based liquid phase microextraction-high performance liquid chromatography with fluorescence detection

A hollow fibre-based liquid phase microextraction (HF-LPME) coupled with high performance liquid chromatography with fluorescence detection (HPLC-FD) method was developed for the determination of carbendazim (MBC) and thiabendazole (TBZ) in apple juice. Some important extraction parameters, such as the pH of the sample solution, extraction time, stirring rate and salt concentration, were optimised. As a result, the optimal HF-LPME conditions were selected as follows: A 4?mL of sample solution (donor phase) at pH of 7.5 was used for the extraction. The pores of the hollow fibre were impregnated by 1-octanol, and 5?mM HCl (pH?=?2.5) was used as the extraction solvent. The extractions were conducted at a stirring rate of 800?rpm for 40?min. After extraction, 10?µL of the extraction solvent was injected into the HPLC system for analysis. The average enrichment factors were 106 and 114 for MBC and TBZ, respectively. A good linear relationship existed in the range of 2.5?～?500?µg?L^?1 and 5?～?500?µg?L^?1for MBC and TBZ in apple juice with the correlation coefficients (r) of 0.9995 and 0.9991, respectively. The limits of detection were 0.8?µg?L^?1 for MBC and 1.5?µg?L^?1 for TBZ (S/N?=?3?:?1). The recoveries of the method were between 86.3% and 106.0% with the relative standard deviations (RSDs) ranging from 3.3% to 8.5%. The HF-LPME-HPLC method has been successfully applied to the analysis of MBC and TBZ in apple juice, indicating that LPME-HPLC may be a promising combination for the analysis of pesticide residues for some food samples.     

Flow-Injection Electrochemiluminescence Detecting Rifampicin Based on Its Sensitizing Effect

Introduction Rifampicin, a semi synthetic compound, is used primarily in the treatment of tuberculosis, and it is also an excellent amistaphyloco antibiotic when used in combination with other antibiotics, so it is very useful clinically.1 Therefore, the determination of rifampicin has attracted much attention. From now on, techniques for the determination of rifampicin have been primarily based on spectrophotometry,2 double-wavelength thin-layer scan,3 chemiluminescence,4 high performance liq…     

Extraction and determination of pyridinium ionic liquid cations in environmental water samples by using strong cation exchange solid phase extraction and ion chromatography

This paper presents a novel analytical method for the determination of pyridinium ionic liquid cations in environmental water samples by ion chromatography coupled with solid phase extraction. The water samples were purified and enriched by a sulphonic acid extraction column, and then the impurities were washed with 10 mL water – 20% (v/v) acetonitrile solution and the analytes eluted with 0.5 mol L^?1 phosphoric acid – sodium dihydrogen phosphate buffer solution – 55% methanol. The eluted analytes were determined by ion chromatography with 3.0 mmol L^?1 methane sulphonic acid – 8% acetonitrile as the mobile phase and direct conductivity detection. Three pyridinium cations were completely separated in 20 min and the retention mechanism basically conforms to the ion exchange mode. The newly developed method has been successfully applied to the analysis of pyridinium cations in spiked environmental water samples, which provided satisfactory recoveries in the range of 98.8% to 100.0% with the relative standard deviations less than 2.8%. The concentration of 0.004 to 0.01 mg L^?1 in water samples can be preconcentrated by this method. The method is accurate, reliable, simple and practical. This research provides a new reference for detecting ionic liquid cations in environmental water samples and studying the environmental risk assessment of ionic liquids.     

Development of a fully automated sequential injection solid-phase extraction procedure coupled to liquid chromatography to determine free 2-hydroxy-4-methoxybenzophenone and 2-hydroxy-4-methoxybenzophenone-5-sulphonic acid in human urine

2-Hydroxy-4-methoxybenzophenone and 2-hydroxy-4-methoxybenzophenone-5-sulphonic acid, commonly known as benzophenone-3 (BZ3) and benzophenone-4 (BZ4), respectively, are substances widely used as UV filters in cosmetic products in order to absorb UV radiation and protect human skin from direct exposure to the deleterious wavelengths of sunlight. As with other UV filters, there is evidence of their percutaneous absorption.This work describes an analytical method developed to determine trace levels of free BZ3 and BZ4 in human urine. The methodology is based on a solid-phase extraction (SPE) procedure for clean-up and pre-concentration, followed by the monitoring of the UV filters by liquid chromatography-ultraviolet spectrophotometry detection (LC-UV). In order to improve not only the sensitivity and selectivity, but also the precision of the method, the principle of sequential injection analysis was used to automate the SPE process and to transfer the eluates from the SPE to the LC system. The application of a six-channel valve as an interface for the switching arrangements successfully allowed the on-line connection of SPE sample processing with LC analysis.The SPE process for BZ3 and BZ4 was performed using octadecyl (C18) and diethylaminopropyl (DEA) modified silica microcolumns, respectively, in which the analytes were retained and eluted selectively. Due to the matrix effects, the determination was based on standard addition quantification and was fully validated. The relative standard deviations of the results were 13% and 6% for BZ3 and BZ4, respectively, whereas the limits of detection were 60 and 30 ng mL⁻¹, respectively. The method was satisfactorily applied to determine BZ3 and BZ4 in urine from volunteers that had applied a sunscreen cosmetic containing both UV filters.