EFFECT OF VINYL ACETATE CONTENT ON THE MECHANICAL PROPERTIES AND MORPHOLOGICAL STRUCTURES OF POLYPROPYLENE

The effect of vinyl acetate （VA） content in ethylene vinyl acetate （EVA） copolyrner on the mechanical properties of polypropylene was investigated. Three different EVA copolymers with concentrations of 3 wt%, 6 wt%, 9 wt%, 12 wt% and 15 wt%, were blended to polypropylene. The mechanical properties such as yield and tensile strengths, elastic modulus, Izod impact strength, hardness and melt flow index of the blends were investigated. Relationship between type of vinyl acetate and concentrations, mechanical, MFI and morphological properties were explored.     

Effect of matrix viscosity on the extent of exfoliation in EVA/organoclay nanocomposites

The influence of matrix viscosity and polarity on ethylene‐vinyl acetate copolymer (EVA) nanocomposites was studied. Five different EVA grades, with different melt flow indexes (MFIs) and/or vinyl acetate (VA) contents, were mixed with two montmorillonite (MMT) nanoclays: pristine and modified with a polar surfactant, producing 75/25 w/w% masterbatches which were subsequently diluted in the EVA matrix to obtain 5 wt% MMT nanocomposites. Although the same VA content, WAXS results, rheological measurements and TEM analysis showed that the lower the EVA viscosity, the greater the tendency to obtain exfoliated and well dispersed nanocomposites with the organically modified clay. On the other hand, the high viscosity EVA nanocomposites showed that the (001) organoclay diffraction peak was shifted to higher values of 2θ, suggesting lamellae collapsing. TGA and FTIR measurements were used to probe the thermal degradation of organoclay; furthermore, it was not possible to identify, by the techniques used, any reaction between the VA groups and hydroxyl surfactant groups. Thus, it was inferred that the organic surfactant was removed (or ejected) from the clay galleries as a consequence of huge shear tensions developed during processing of the masterbatches/nanocomposites with high viscosity EVA matrices. Copyright © 2009 John Wiley & Sons, Ltd.     

A dielectric study of poly(ethylene-co-vinylacetate)–poly(vinyl chloride) blends. I. Miscibility and phase behavior

Measurements of the complex permittivity were used to study miscibility and phase behavior in blends of poly(vinyl chloride) (PVC) with two random ethylene—vinyl acetate (EVA) copolymers containing 45 and 70 wt % of vinyl acetate. The dielectric β relaxation of the pure polymers and blends was followed as a function of temperature and frequency for different blend compositions and thermal treatments. Blends of EVA 70/PVC were found to be miscible for compositions of about 25% EVA 70 and higher. Blends of lower EVA 70 content showed evidence of two-phase behavior. EVA 45/PVC blends were found to be miscible only at the composition extremes; at intermediate compositions these blends were two-phase, partially miscible. Both blend systems showed lower critical solution temperature behavior. Phase separation studies revealed that in the EVA 45/PVC blends, PVC was capable of diffusing into the higher T_g phase at temperatures below the T_g of the upper phase. In the blends, ion transport losses were significant above the loss peak temperatures, and in the two-phase systems, often obscured the upper temperature loss process. It was shown possible, however, to correct the loss curves for this transport contribution.     

Thermorheological analysis of PVC blends

The effect of temperature on dynamic viscoelastic measurements of miscible poly (vinyl chloride) (PVC)/ethylene‐vinyl acetate–carbon monoxide terpolymer (EVA‐CO) and immiscible PVC/high‐density polyethylene (HDPE) and PVC/chlorinated polyethylene (CPE) molten blends is discussed. PVC plasticized with di(2 ethyl hexyl) phthalate (PVC/DOP) and CaCO₃ filled HDPE (HDPE/CaCO₃) are also considered for comparison purposes. Thermorheological complexity is analyzed using two time–temperature superposition methods: double logarithmic plots of storage modulus, G′, vs. loss modulus, G″, and loss tangent, tan δ, vs. complex modulus, G*, plots. Both methods reveal that miscible PVC/EVA‐CO and PVC/DOP systems are thermorheologically complex, which is explained by the capacity of PVC to form microdomains or crystallites during mixing and following cooling of the blends. For immiscible PVC/HDPE and PVC/CPE blends the results of log G′ vs. log G″ show temperature independence. However, when tan δ vs. log G* plots are used, the immiscible blends are shown to be thermorheologically complex, indicating that the morphology observed by microscopy and constitued by a PVC phase dispersed in a HDPE or CPE matrix, is reflected by this rheological technique. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 469–477, 2000     

Effect of Electron Beam Irradiation and Ethylene Vinyl Acetate Copolymer on the Properties of NBR/HDPE Blends

The mechanical and physical properties of blends based essentially on nitrile butadiene rubber (NBR) and different ratios of high density polyethylene (HDPE) up to 25 parts per hundred part of rubber (phr) before and after electron beam irradiation were investigated. The values of tensile strength (TS), tensile modulus at 50% elongation (M₅₀), hardness and gel fraction % (GF%) of NBR/HDPE blends were increased with both irradiation dose and by increasing the content of HDPE in the blends. On the other hand, the values of elongation at break (E _b ) were decreased with both irradiation dose and the content of HDPE in the blends. By loading NBR/HDPE (100/25) blend with ethylene vinyl acetate (EVA) copolymer the mechanical and physico-chemical properties were improved. Moreover, the degree of improvement is proportional to the loading content of EVA.     

Crystal and phase morphology of dynamic-packing-injection-molded high-density polyethylene/ethylene vinyl acetate blends

The effect of shear stress, provided by so-called dynamic-packing injection molding, on crystal morphology and phase behavior was investigated for high-density polyethylene (HDPE) in blends with ethylene vinyl acetate (EVA) of various viscosities and vinyl acetate (VA) contents, with the aid of differential scanning calorimetry, two-dimensional small-angle X-ray scattering (2D SAXS), and scanning electron microscopy (SEM). A shish-kebab pattern was found in the oriented zones of dynamic samples, and the ratio of shish to kebab increased as a function of the EVA content in the blends up to 20 wt %, regardless of the VA content. This showed that molecules of HDPE could easily be stretched to form a shish structure in the presence of EVA. Moreover, a large increase in the long spacing, characterized by 2D SAXS measurements, was achieved because of the presence of EVA. The SEM results showed an obvious decrease in the domain size of the EVA phase under the effect of shear stress. All these results suggested shear-induced mixing between HDPE and EVA, in that ethylene segments of EVA molecules could be forged in the shish structure during shear and the other fractions of EVA were located in the amorphous regions between the adjacent lamellae of HDPE. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1831–1840, 2004     

ASSOCIATION OF ETHYLENE—VINYL ACETATE COPOLYMER IN DILUTE SOLUTIONS Ⅲ. CRITICAL ASSOCIATION CONCENTRATION*

Association behavior of ethylene vinyl acetate (EVA) copolymer in foursolvents 1, 2-dichloroethane (DCE), cyclohexane (CYH), xylene (XYL) and chloroform(CF) has been investigated by dilute solution viscometry The critical association concen-tration (C_A) was determined at which the incipient decrease in slope of the η_(sp)/C～ Ccurve in solutions at the dilute regime. Our results showed that whether the CA couldexist depends on solvent property. The values of CA in DCE increase with increasing, oftemperature and vinyl acetate (VA) content in EVA and decreasing of molecular weight ofEVA.     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002     

Effect of vinyl acetate content and electron beam irradiation on the flame retardancy, mechanical and thermal properties of intumescent flame retardant ethylene-vinyl acetate copolymer

Ethylene vinyl acetate copolymer (EVA) flame retarded by ammonium polyphosphate (APP) and pentaerythritol (PER) was cross-linked by electron beam irradiation. The effects of vinyl acetate content and electron beam irradiation on the flame retardancy, mechanical and thermal properties of EVA composites were investigated. The volatilized products of EVA/APP/PER composites were characterized by thermogravimetric analysis/infrared spectrometry. As VA content increased, the volatilized products increased in the second decomposition step, but decreased in the third decomposition step. For all samples, the increase of irradiation dose could improve both the gel content and the Limit Oxygen Index (LOI, the minimum oxygen concentration by volume for maintaining the burning of a material) values of irradiated composites. The mechanical and thermal properties of the irradiated EVA composites were also evidently improved at appropriate irradiation dose as compared with those of unirradiated EVA composites, whereas these properties decrease at higher irradiation dose because of the electron beam irradiation-induced oxidative degradation or chain scission.     

Distribution of nanoclay in a new TPV/nanoclay composite prepared through dynamic vulcanization

In this article distribution of nanoclay between the two phases of a new class of dynamically vulcanized TPV based on POE/EVA(Polyethylene octene elastomer/ethylene vinyl acetate copolymer) elastomers prepared with various amounts of organoclay (0.5, 1 and 3 wt%) using dicumyl peroxide (DCP) as vulcanizing agent by reactive melt blending process has been studied. Different specimens of POE and POE/EVA blend with and without clay were prepared. The effects of organoclay on mechanical properties, swelling kinetics, crystallinity, vulcanization characteristics, dynamic mechanical behaviour, electrical properties and morphology were studied. DMA and morphological analysis revealed the formation of a Thermoplastic vulcanizate. XRD analysis showed decrease in crystallinity on addition of EVA in POE matrix. However, morphological observation of the fractured surface suggested that the smaller EVA domain was quite uniformly distributed into the POE phase and the clay phase was predominantly dispersed in the EVA phase of the TPVs and 0.5% clay mainly improved the mechanical properties and elongation of the blends. Swelling characteristics, electrical properties and storage modulus were also improved with the clay in case of the blend containing higher EVA content which further supports the fact that nanoclay was preferably distributed in the more polar EVA phase.     

Reduced percolation thresholds of immiscible conductive blends

The DC conductivity of polymer blends composed of poly(ethylene‐co‐vinyl acetate) (EVA) and high density polyethylene (HDPE), where a conductive carbon black (CB) had been preferentially blended into the HDPE, were investigated to establish the percolation characteristics. The blends exhibited reduced percolation thresholds and enhanced conductivities above that of the individually carbon filled HDPE and EVA. The percolation threshold of the EVA/HDPE/CB composites was between 3.6 and 4.2 wt % carbon black, where the volume resistivity changed by 8 orders of magnitude. This threshold is at a significantly lower carbon content than the individually filled HDPE or EVA. At a carbon black loading of 4.8 wt %, the EVA/HDPE/CB composite exhibits a volume resistivity which is approximately 14 and 11 orders of magnitude lower than the HDPE/CB and EVA/CB systems, respectively, at the same level of incorporated carbon black. The dielectric response of the ternary composites, at a temperature of 23°C and frequency of 1 kHz, exhibited an abrupt increase of ca. 252% at a carbon concentration of 4.8 wt %, suggesting that the percolation threshold is somewhat higher than the range predicted from DC conductivity measurements. Percolating composites with increasing levels of carbon black exhibit significantly greater relative permittivity and dielectric loss factors, with the composite containing 6 wt % of carbon black having a value of ϵ′ ≈ 79 and ϵ″ ≈ 14. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1899–1910, 1999     

Toughening effect of ethylene‐vinyl acetate rubber on nylon 1010 compatibilized by maleated ethylene‐vinyl acetate copolymers

The toughening effect of ethylene‐vinyl acetate rubbers (EVM) with maleated ethylene‐vinyl acetate copolymers (EVA‐g‐MAH) on the nylon 1010 was investigated. The addition of 5 phr (per hundred nylon 1010) EVM increased the elongation at break of nylon 1010 to a great extent. The notched Izod impact strength of nylon/EVM blends increased with increasing EVM content. Scanning electron microscope showed that the EVM particle size was around 0.5 μm when the EVM content was 5 phr and increased with increasing EVM content. After the addition of EVA‐g‐MAH to nylon/EVM (100/20) blend, the average diameter of EVM particles decreased from more than 1 μm to 0.5–0.6 μm. EVA‐g‐MAH could improve the adhesion between nylon 1010 and EVM. A sharp brittle‐ductile transition (BDT) was observed when the interparticle distance was about 0.2 μm, independent of the addition of EVA‐g‐MAH. The notched Izod impact strength of nylon/EVM blends at low temperatures was measured and the BDT shifted toward low temperatures with increasing EVM or EVA‐g‐MAH content. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 434–444, 2009     

Grafting of polycaprolactone onto poly(ethylene‐co‐vinyl alcohol) and application to polyethylene‐based bioerodable blends

Poly(ethylene‐co‐vinyl acetate) (EVA) powders containing 10 and 20 wt % of vinyl acetate (VAc) units was saponified in ethanol/KOH solution in a heterogeneous manner. Intermolecular interaction between vinyl alcohol(VOH) units in the produced poly(ethylene‐co‐vinyl alcohol) (EVOH) promoted the crystallization of intervening segments composed of ethylene units. Ring opening polymerization of caprolactone (CL) in the presence of EVOH gave EVOH‐g‐PCL graft copolymers with relatively short chain branches. Even though the graft copolymerization was carried out in a homogeneous solution, all the VOH units were not equally reactive for the PCL grafting. And the unreacted VOH units decreased very slowly with the graft copolymerization time. EVOH‐g‐PCL decreased the domain size of the dispersed phase in low density polyethylene (PE)/biodegradable master batch (MB) blends, and thus increased their tensile properties significantly. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2561–2569, 2002     

Toughening of poly(lactic acid) by ethylene-co-vinyl acetate copolymer with different vinyl acetate contents

The well-known bio-based and biocompostable poly(lactic acid), PLA, suffers from brittleness and a low heat distortion temperature. In this paper, we address a possible route to make PLA tough(er) by blending with ethylene-co-vinyl acetate (EVA) with different vinyl acetate contents. The compatibility and phase morphology of the PLA/EVA blends was controlled by the ratio of vinyl acetate and ethylene in the random copolymers. Tough PLA/EVA blends with increased impact toughness, up to a factor of 30, were obtained with a maximum toughness at a vinyl acetate content of approximately 50 wt.%. The local deformation mechanism was well studied by TEM, SAXS and SEM. It revealed that internal rubber cavitation in combination with matrix yielding is the dominant toughening mechanism for the PLA/EVA blends under both impact and tensile testing conditions.     

Effect of the liquid–liquid phase separation on the crystallization behavior and mechanical properties of poly(ethylene‐ran‐vinyl acetate) and paraffin wax blend

The effect of liquid–liquid phase‐separation (LLPS) on the crystallization behavior and mechanical properties of poly(ethylene‐ran‐vinyl acetate) (EVA) with various amounts of vinyl acetate and paraffin wax blend was investigated. The blend of EVA‐H (9.5% vinyl acetate) and the wax became homogeneous at temperatures greater than its upper critical solution temperature (UCST) (98°C), and an LLPS was observed between UCST and the melting point of 88°C for EVA‐H in the blend. The existence of the LLPS is attributed to the relatively large amount of the hydrophilic component of vinyl acetate in EVA, although the molecular weight of the wax was just 560. However, LLPS did not occur for the EVA/wax blend when the content of vinyl acetate in EVA was less than 3%. This behavior was explained by using the Flory–Huggins lattice model with an effective interaction parameter. The degree of crystallinity of EVA‐H in the EVA‐H/wax blend, judged from a melting endothermic peak in differential scanning calorimeter (DSC) thermograms obtained during heating runs, decreased with increasing duration time in the LLPS region. The flexural modulus of the EVA/wax blend became maximum at certain blend composition (about 30 ∼ 40 wt % EVA depending upon the amount of vinyl acetate). This behavior can be explained by the fact that this blend composition has the largest relative degree of crystallinity of EVA measured by DSC and wide‐angle X‐ray scattering method. We found that the flexural modulus of the binder itself is directly related to that of a feedstock consisting of larger amounts of metal powder and the binder, which can help someone to develop a suitable binder system for a powder injection molding process. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1991–2005, 1999     

Conducting composites from EPDM–EVA blends

The effect of ethylidene norbornene (ENB) content of ethylene propylene aiene rubber (EPDM) and vinyl acetate (VA) content of ethylene vinyl acetate copolymer (EVA), as well as the blending sequence, on the conductivity of composites based on EPDM–EVA–carbon black have been studied. Black master batches show a lower extent of cure than the preblended system followed by black addition. EPDM having a high ENB content shows higher conductivity under ambient conditions. Preblended systems give rise to higher conductivity in the case of low-ENB content EPDM. But for high-ENB content EPDM, the blending of black master batches imparts high conductivity. Two types of conduction are observed in this case and the transition temperature depends on the VA content of EVA. It appears that there exists a correlation between activation energy of curing and that of conduction.     

Linear viscoelastic characteristics of in situ compatiblized binary polymer blends with viscoelastic properties of components variable

By Friedel‐Crafts alkylation reaction, catalyzed by a Lewis acid of anhydrous aluminum chloride (AlCl₃), binary polymer blends of polypropylene (PP)/polystyrene (PS) with volume proportion of 80/20 were in situ compatiblized and prepared in an XSS‐30 melt mixer at 210 °C. The linear viscoelastic characteristics of the blends were investigated by checking the variations of storage modulus, loss modulus, complex modulus, and complex viscosity of the in situ compatiblized blends, which were dependent on AlCl₃ content. In addition, Han plots of the in situ compatiblized blends with different AlCl₃ content were also used to characterize the linear viscoelastic properties of the blends. The results showed that both the dynamic rheological parameters and the Han plots were obviously influenced by the rheological properties of the matrix and slightly influenced by the rheological properties of the dispersed phase. Further investigations revealed that phase geometry contributions to the dynamic rheological parameters of the blends could be ignored in comparison with the contributions of the components and the interfacial modification, which were defined and obtained according to log‐linear‐additivity rule. The linear viscoelastic characteristics of the blends were mainly controlled by the combination of the effects of interfacial modification between phases and the rheological properties of the matrix. Storage modulus is the most sensitive dynamic rheological parameter to characterize the interfacial compatiblization effects in the in situ compatiblized binary polymer blends with rheological properties of components variable. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1349–1362, 2010     

Kinetic Study of the Accelerating Effect of Coal-burning Additives on the Combustion of Graphite

The relationship between copolymer composition and transition temperatures was studied by means of differential scanning calorimetric analysis and dynamic mechanical spectroscopy. Six samples of ethylene vinyl acetate (EVA) copolymers containing from 5 to 40 mass per cent of vinyl acetate (VA) were studied. The differential scanning calorimetric analysis revealed that each EVA copolymer displays two endothermic peaks (T_m1 and T_m2 ) in the melting zone. Dynamic mechanical spectroscopy was used to determine the primary relaxation temperature (T_α ) for EVA copolymers. This latter characteristic is relatively insensitive to the level of vinyl acetate contained in the copolymer and is influenced by the pulsation frequency ω, also named the angular frequency. This revised version was published online in July 2006 with corrections to the Cover Date.     

A dielectric study of poly(ethylene-co-vinyl acetate)–poly(vinyl chloride) blends. II. Loss curve broadening and correlation parameters

Normalized dielectric loss curves for blends of PVC with an EVA copolymer containing 70% vinyl acetate showed significant broadening with increasing PVC content. In conjunction with phase separation studies it was concluded that increasing loss curve broadness correlated with increasing tendency toward phase separation. Calculation of correlation parameters for the blends revealed differences in intermolecular correlations with blend composition.     

A comparative study of UV aging characteristics of poly(ethylene‐co‐vinyl acetate) and poly(ethylene‐co‐vinyl acetate)/carbon black mixture

In this comparative study, the effect of carbon black (CB) on the UV aging characteristics of poly(ethylene‐co‐vinyl acetate) (EVA) was investigated. EVA, containing 13% vinyl acetate (VA), and poly(ethylene‐co‐vinyl acetate)/carbon black mixture (EVA/CB), containing 13% VA and 1% CB, were aged by means of UV light with a wavelength in the vicinity of 259 nm, in air, up to 400 hr. Sol‐gel analyses were made to determine the percentage gelation of both virgin and aged samples. FT‐IR measurements were performed to follow the chemical changes which took place in the samples during aging. Dynamic and isothermal thermogravimetry studies were performed for determination of the thermal stabilities of virgin and aged samples. Sol‐gel analysis results showed that EVA itself has a tendency to form a gel under UV irradiation. EVA/CB, however, becomes a gel to a smaller extent, comparatively, under the same conditions. As a result of FT‐IR measurements, some oxidation products such as ketone, lactone and vinyl species were observed through UV ageing of EVA and EVA/CB. Thermal analysis experiments exhibited that the thermal stabilities of EVA and EVA/CB decreased, to a similar extent through UV aging. Copyright © 2004 John Wiley & Sons, Ltd.