Transport properties of undoped and Br-doped PbTe sintered at high-temperature and pressure ≥4.0 GPa

The thermoelectric properties of nominally undoped PbTe and Br doped PbTe materials sintered at high-pressure and high-temperature (HPHT) have been studied. All samples show n-type semiconducting behavior with negative thermopower. For undoped PbTe, four different HPHT treatments were performed at pressures between 4.0 and 6.5 GPa. PbTe doped with Br at 0.5, 1.0, 2.0, 3.0×10¹⁹ cm⁻³ was HPHT treated at 4.0 GPa and 1045 °C. As the dopant concentration increases, the absolute thermopower decreases, thermal conductivity increases, and electrical resistivity decreases. At a nominal dopant concentration of 1.0×10¹⁹ cm⁻³, carrier mobility of 1165 cm²/V s and dimensionless thermoelectric figure-of-merit, ZT, of around 0.27 at 300 K were obtained. These results demonstrate that HPHT post-processing is a viable and controllable way of tuning the thermoelectric properties of PbTe-based materials.     

Thermoelectric properties of p-type pseudo-binary (Ag0.365Sb0.558Te)x-(Bi0.5Sb1.5Te3)1−x (x=0-1.0) alloys prepared by spark plasma sintering

In this paper, pseudo-binary (Ag_0.365Sb_0.558Te)_x-(Bi_0.5Sb_1.5Te₃)_1−x (x=0-1.0) alloys were prepared using spark plasma sintering technique, and the composition-dependent thermoelectric properties were evaluated. Electrical conductivities range from 7.9×10⁴ to 15.6×10⁴ Ω⁻¹ m⁻¹ at temperatures of 507 and 318 K, respectively, being about 3.0 and 8.5 times those of Bi_0.5Sb_1.5Te₃ alloy at the corresponding temperatures. The optimal dimensionless figure of merit (ZT) of the sample with molar fraction x=0.025 reaches 1.1 at 478 K, whereas that of the ternary Bi_0.5Sb_1.5Te₃ alloy is 0.58 near room temperature. The results also reveal that a direct introduction of Ag_0.365Sb_0.558Te in the Bi-Sb-Te system is much more effective to the property improvement than naturally precipitated Ag_0.365Sb_0.558Te in the Ag-doped Ag-Bi-Sb-Te system.     

Investigation of the quasi-ternary system LaMnO3-LaCoO3-“LaCuO3”—I: the series La(Mn0.5Co0.5)1−xCuxO3−δ

The La(Mn_0.5Co_0.5)_1−xCu_xO_3−δ series with x=0, 0.05, 0.1, 0.2, 0.4, 0.6, 0.8 and 1 was synthesized by the Pechini method to obtain insight into the phase formation in the quasi-ternary LaMnO₃-LaCoO₃-“LaCuO₃” system caused by the instability of LaCuO₃ under ambient conditions. After sintering at 1100°C some remarkable results were obtained: LaMn_0.3Co_0.3Cu_0.4O_3−δ crystallized as a single phase in the orthorhombic perovskite structure typical of LaCuO₃. Among the synthesized compositions this compound showed the highest electrical conductivity in air at 800°C (155 S cm⁻¹) and also the highest thermal expansion coefficient (α_30−800°C=15.4×10⁻⁶ K⁻¹). The LaCuO_3−δ composition also crystallized as a single phase but in a monoclinic structure although previous investigations have shown that other phases are preferably formed after sintering at 1100°C. The electrical conductivity and thermal expansion coefficient were the lowest within the series of compositions, i.e. 9.4 S cm⁻¹ and 11.9×10⁻⁶ K⁻¹, respectively.     

p-Type thermoelectric properties of the oxygen-deficient perovskite Ca2Fe2O5 in the brownmillerite structure

Brownmillerite calcium ferrite was synthesized in air at 1573 K and thermoelectric properties (direct current electrical conductivity σ, Seebeck coefficient α, thermal conductivity κ, thermal expansion α_L) were measured from 373 to 1050 K in air. Seebeck coefficient was positive over all temperatures indicating conduction by holes, and electrical properties were continuous through the Pnma-Imma phase transition. Based on the thermopower and conductivity activation energies as well as estimated mobility, polaron hopping conduction was found to dominate charge transport. The low electrical conductivity, <1 S/cm, limits the power factor (α²σ), and thus the figure of merit for thermoelectric applications. The thermal conductivity values of ∼2 W/mK and their similarity to Ruddlesden-Popper phase implies the potential of the alternating tetrahedral and octahedral layers to limit phonon propagation through brownmillerite structures. Bulk linear coefficient of thermal expansion (∼14×10⁻⁶ K⁻¹) was calculated from volume data based on high-temperature in situ X-ray powder diffraction, and shows the greatest expansion perpendicular to the alternating layers.     

Synthesis of nanospherical Fe3BO6 anode material for lithium-ion battery by the rheological phase reaction method

This paper developed a novel method, the rheological phase reaction method, to synthesize nanospherical Fe₃BO₆. The sizes and morphologies of products vary with the calcination temperatures. Spherical particles with a uniform size about 40 nm in a monodisperse state were obtained at 800 °C, while the spherical particles with a larger size of 100-500 nm were obtained at 900 °C. The electrochemical properties of these Fe₃BO₆ nanospheres were investigated. Sample synthesized at 800 °C delivers a high reversible capacity above 500 mAh g⁻¹. Sample synthesized at 900 °C possesses relatively good cycleability with a capacity retaining of 376 mAh g⁻¹ after 10 cycles. The measurement of electrochemical impedance spectra for the first time indicated that smaller Fe₃BO₆ nanoparticles intend to give higher impedance of solid-electrolyte interface layer and lower charge-transfer impedance after the first discharge. Additionally, it can be speculated that the increase of resistance charge-transfer is the possible reason for the capacity fading during cycling.     

A novel microwave dielectric ceramic Ca2Zn4Ti16O38: Preparation and dielectric properties

A novel microwave dielectric powder with composition of Ca₂Zn₄Ti₁₆O₃₈ was synthesized through a citrate sol-gel process. The development of crystalline phases with heat-treating temperature for the gel derived powders was evaluated by using thermo-gravimetric analysis and X-ray powder diffraction analysis techniques. The pure phase of Ca₂Zn₄Ti₁₆O₃₈ with crichtonite crystal structure was obtained at relatively low temperature of 1000 °C. The synthesized powder has high reactivity and the dense ceramics with single crystalline phase were obtained at low sintering temperature of 1100 °C. Impedance spectroscopy and microwave dielectric measurements on sintered samples showed the present compound to be a modest dielectric insulator with excellent dielectric properties of ε_r∼47-49, Qf value ∼27,800-31,600 GHz and τ_f∼+45 to +50 ppm/°C. It shows comparable microwave dielectric properties to other moderate-permittivity microwave dielectrics, but much lower sintering temperature of 1100 °C.     

Thermoelectric properties of polycrystalline La1−xSrxCoO3

Thermoelectric properties of polycrystalline La_1−xSr_xCoO₃, where Sr²⁺ is substituted in La³⁺ site in perovskite-type LaCoO₃, have been investigated. Sr-doping increases the electrical conductivity (σ) of La_1−xSr_xCoO₃, and also decreases the Seebeck coefficient (S) for 0.01?x?0.40. A Hall coefficient measurement reveals that the increase in electrical conductivity arises from increases in both carrier concentration and the Hall mobility. The decrease in the Seebeck coefficient is caused by a decrease in carrier effective mass as well as increase in carrier concentration. The highest power factor (σS²) is 3.7×10⁻⁴ W m⁻¹ K⁻² at 250 K for x=0.10. The thermal conductivity (κ) is about 2 W m⁻¹ K⁻¹ at 300 K for 0?x?0.04, and increases for x?0.05 because of an increase in heat transport by conductive carrier. The thermoelectric properties of La_1−xSr_xCoO₃ are improved by Sr-doping, and the figure of merit (Z=σS² κ⁻¹) reaches 1.6×10⁻⁴ K⁻¹ for x=0.06 at 300 K (ZT=0.048). For heavily Sr-doped samples, the thermoelectric properties diminish mainly because of the decrease in the Seebeck coefficient and the increase in thermal conductivity.     

Effect of sintering on the ionic conductivity of garnet-related structure Li5La3Nb2O12 and In- and K-doped Li5La3Nb2O12

Garnet-structure related metal oxides with the nominal chemical composition of Li₅La₃Nb₂O₁₂, In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ and K-substituted Li_5.5La_2.75K_0.25Nb₂O₁₂ were prepared by solid-state reactions at 900, 950, and 1000 °C using appropriate amounts of corresponding metal oxides, nitrates and carbonates. The powder XRD data reveal that the In- and K-doped compounds are isostructural with the parent compound Li₅La₃Nb₂O₁₂. The variation in the cubic lattice parameter was found to change with the size of the dopant ions, for example, substitution of larger In³⁺(r_CN6: 0.79 Å) for smaller Nb⁵⁺ (r_CN6: 0.64 Å) shows an increase in the lattice parameter from 12.8005(9) to 12.826(1) Å at 1000 °C. Samples prepared at higher temperatures (950, 1000 °C) show mainly bulk lithium ion conductivity in contrast to those synthesized at lower temperatures (900 °C). The activation energies for the ionic conductivities are comparable for all samples. Partial substitution of K⁺ for La³⁺ and In³⁺ for Nb⁵⁺ in Li₅La₃Nb₂O₁₂ exhibits slightly higher ionic conductivity than that of the parent compound over the investigated temperature regime 25-300 °C. Among the compounds investigated, the In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ exhibits the highest bulk lithium ion conductivity of 1.8×10⁻⁴ S/cm at 50 °C with an activation energy of 0.51 eV. The diffusivity (“component diffusion coefficient”) obtained from the AC conductivity and powder XRD data falls in the range 10⁻¹⁰-10⁻⁷ cm²/s over the temperature regime 50-200 °C, which is extraordinarily high and comparable with liquids. Substitution of Al, Co, and Ni for Nb in Li₅La₃Nb₂O₁₂ was found to be unsuccessful under the investigated conditions.     

Preparing nanometer scaled Tb-doped Y2O3 luminescent powders by the polyol method

Sub-micrometer Tb-doped Y₂O₃ luminescent powders were prepared from nitrate precursors using the polyol method. Just after precipitation, the powders consist of agglomerates with a spherical shape and a size ranging between 400 and 500 nm. Each agglomerate is composed of ultra-small crystallites (from 3 to 6 nm) of a bcc oxide phase whose luminescence presents original features in comparison with bulk materials. Powders were further calcinated at different temperatures and for annealing below 900 °C, highly crystalline samples with the classical green ⁵D₄→⁷F₅ luminescent transitions of Tb³⁺ ions are obtained. For optimized annealing temperatures, sintering between the agglomerates is avoided and a sub-micrometric powder with a narrow size distribution and a high luminescence is obtained.     

Synthesis of PbTiO3 ceramics using mechanical alloying and solid state sintering

The pressure-less sintering behavior of PbTiO₃ powders synthesized by mechanical alloying TiO₂ and PbO was investigated using dilatometry and Rietveld refinements of X-ray diffraction patterns. As-synthesized, the powders are nanocrystalline with a mean particle size of 20 nm. Pressure-less sintering in the range 500-1050°C gives single phase ceramics with densities of 85-90% and crystallite sizes in the range 80-400 nm. Cracking due to the paraelectric-ferroelectric phase transition was not observed in samples sintered below 700°C due to the small crystallite size whereas macroscopic cracks formed in samples sintered above 700°C. Rietveld analysis indicates the formation of Pb vacancies in samples sintered and held for 24 h at intermediate temperatures (600-1000°C) which gives some insight into the mechanism of Pb loss and second phase formation in this system.     

Synthesis crystal structure and ionic conductivity of Ca0.5Bi3V2O10 and Sr0.5Bi3V2O10

Two new compounds Ca_0.5Bi₃V₂O₁₀ and Sr_0.5Bi₃V₂O₁₀ have been synthesized in the ternary system: MO-Bi₂O₃-V₂O₅ system (M=M²⁺). The crystal structure of Sr_0.5Bi₃V₂O₁₀ has been determined from single crystal X-ray diffraction data, space group and Z=2, with cell parameters a=7.1453(3) Å, b=7.8921(3) Å, c=9.3297(3) Å, α=106.444(2)°, β=94.088(2)°, γ=112.445(2)°, V=456.72(4) Å³. Ca_0.5Bi₃V₂O₁₀ is isostructural with Sr_0.5Bi₃V₂O₁₀, with, a=7.0810(2) Å, b=7.8447(2) Å, c=9.3607(2) Å, α=106.202(1)°, β=94.572(1)°, γ=112.659(1)°, V=450.38(2) Å³ and its structure has been refined by Rietveld method using powder X-ray data. The crystal structure consists of infinite chains of (Bi₂O₂) along c-axis formed by linkage of BiO₈ and BiO₆ polyhedra interconnected by MO₈ polyhedra forming 2D layers in ac plane. The vanadate tetrahedra are sandwiched between these layers. Conductivity measurements give a maximum conductivity value of 4.54×10⁻⁵ and 3.63×10⁻⁵ S cm⁻¹ for Ca_0.5Bi₃V₂O₁₀ and Sr_0.5Bi₃V₂O₁₀, respectively at 725 °C.     

Synthesis, crystal structure and thermal behavior of Sr3B2SiO8 borosilicate

Single crystals of Sr₃B₂SiO₈ were obtained by solid-state reaction of stoichiometric mixture at 1200 °C. The crystal structure of the compound has been solved by direct methods and refined to R1=0.064 (wR=0.133). It is orthorhombic, Pnma, a=12.361(4), b=3.927(1), c=5.419(1) Å, V=263.05(11) Å³. The structure contains zigzag pseudo-chains running along the b axis and built up from corner sharing (Si,B)−O polyhedra. Boron and silicon are statistically distributed over one site with their coordination strongly disordered. Sr atoms are located between the chains providing three-dimensional linkage of the structure.The formation of Sr₃B₂SiO₈ has been studied using annealing series in air at 900-1200 °C. According powder XRD, the probe contains pure Sr₃B₂SiO₈ over 1100 °C. The compound is not stable below 900 °C. In the pseudobinary Sr₂B₂O₅-Sr₃B₂SiO₈ system a new series of solid solutions Sr_3−xB₂Si_1−xO_8−3x (x=0-0.9) have been crystallized from melt. The thermal behavior of Sr₃B₂SiO₈ was investigated using powder high-temperature X-ray diffraction (HTXRD) in the temperature range 20-900 °C. The anisotropic character of thermal expansion has been observed: α_a= −1.3, α_b=23.5, α_c=13.9, and α_V=36.1×10⁻⁶ °C⁻¹ (25 °C); α_a= −1.3, α_b=23.2, α_c=5.2, and α_V=27.1×10⁻⁶ °C⁻¹ (650 °C). Maximal thermal expansion of the structure along of the chain direction [0 1 0] is caused by the partial straightening of chain zigzag. Hinge mechanism of thermal expansion is discussed.     

Structural and conductivity studies of Y10−xLaxW2O21

The aim of this work was to determine structural parameters of the Y_10−xLa_xW₂O₂₁ (x=0-10) solid solution series and investigate their electric properties. Crystallographic data shows a gradual increase in symmetry with increasing La content, as the structure evolves from orthorhombic, Y₁₀W₂O₂₁, towards the pseudo-cubic structure of Y₅La₅W₂O₂₁. The solubility limit of La₂O₃ was found to be 50% (x=5). Above this level two phases were observed, La₆W₂O₁₅ and (La,Y)_10+xW_2−xO_21−δ. The conductivity of Y rich samples was very low, with σ of the order 2×10⁻⁵-5×10⁻⁵ S cm⁻¹ at 1000 °C, whilst ionic conductivity was observed for most La rich doped samples. The highest conductivity was observed for La₁₀W₂O₂₁ and its doped analogues, at 1×10⁻³-5×10⁻³ S cm⁻¹ at 1000 °C. Unit cell parameters were determined as a function of temperature from 0 to 1000°C, and thermal expansion of these materials was determined from temperature studies carried out at the Australian Synchrotron facility in Melbourne, Victoria, Australia.     

Mixed conductivity and Mössbauer spectra of (La0.5Sr0.5)1−xFe1−yAlyO3−δ (x=0-0.05, y=0-0.30)

Aluminum incorporation in the rhombohedrally distorted perovskite lattice of (La_0.5Sr_0.5)_1−xFe_1−yAl_yO_3−δ (x=0-0.05, y=0-0.30) decreases the unit cell volume and partial ionic and p-type electronic conductivities, while the oxygen nonstoichiometry and thermal expansion at 900-1200 K increase on doping. The creation of A-site cation vacancies has an opposite effect on the transport properties of Al-substituted ceramics. The maximum A-site deficiency tolerated by the (La,Sr)(Fe,Al)O_3−δ structure is however limited, close to 3-4%. The Mössbauer spectroscopy revealed progressive localization of electron holes and a mixed charge-compensation mechanism, which results in higher average oxidation state of iron when Al³⁺ concentration increases. The average thermal expansion coefficients of (La_0.5Sr_0.5)_1−xFe_1−yAl_yO_3−δ are (12.2-13.0)×10⁻⁶ K⁻¹ at 300-900 K and (20.1-30.0)×10⁻⁶ K⁻¹ at 900-1200 K in air. The steady-state oxygen permeability (OP) of dense Al-containing membranes is determined mainly by the bulk ionic conductivity. The ion transference numbers at 973-1223 K in air, calculated from the oxygen permeation and faradaic efficiency (FE) data, vary in the range 1×10⁻⁴-3×10⁻³, increasing with temperature.     

Formation, sintering, and electrical conductivity of perovskite Sm(Cr1−xMgx)O3 (0?x?0.23) prepared by the hydrazine method

The presence of SmCrO₄ is experimentally established. In Mg²⁺-substituted SmCrO₃, single-phase perovskite Sm(Cr_1−xMg_x)O₃, where x=0-0.23, are formed at ∼830°C by decomposition of Sm(Cr_1−xMg_x)O₄ which crystallizes at 530-570°C from amorphous materials prepared by the hydrazine method. Sm(Cr_1−xMg_x)O₃ solid solution powders consisting of submicrometer-size particles are sinterable; dense materials can be fabricated by sintering for 2 h at 1700°C in air. The relative densities, grain sizes, and electrical conductivities increase with increased Mg²⁺ content. Sm(Cr_0.77Mg_0.23)O₃ materials exhibit an excellent direct current electrical conductivity of 2.2×10³ S m⁻¹ at 1000°C.     

Mechanism of the low thermal expansion in α-Hf2O(PO4)2 and its zirconium analog

The thermal expansion of recently characterized α-Zr₂O(PO₄)₂ and α-Hf₂O(PO₄)₂ is found to be very low (respectively 2.6 and 2.9×10⁻⁶ K⁻¹, 20-900  °C). High-temperature X-ray diffraction and Rietveld analysis allowed to identify a dual contraction mechanism, involving a classical ring deformation and the rocking of bridging oxygens.     

Microstructure and electrical transport in nano-grain sized Ce0.9Gd0.1O2−δ ceramics

An enhancement of the electrical conductivity has been found in nano-grain sized Ce_0.9Gd_0.1O_2−δ ceramics when measured in N₂ (p_O2=3.5×10⁻⁶ atm) in comparison with the most commonly accepted values of bulk ionic conductivity. We first present the synthesis and characterisation of the nanoparticles later used for the preparation of dense nanoceramics of Gd-doped CeO₂. The nanoparticles were characterised by X-ray diffraction (XRD), atomic force microscopy (AFM) and transmission electron microscopy (TEM). The good sintering properties of these nanopowders allowed us to obtain very dense ceramics (>90% theoretical density) while keeping the grain size close to 100 nm. The microstructure of these nanoceramics was analysed by AFM and scanning electron microscopy (SEM) while the electrical characterisation was performed by the 4-point dc technique between 500 and 950 °C in air or N₂ and ac impedance between 150 and 400 °C in air and or argon. We briefly discuss the possibilities of electron vs. oxygen ion conduction and grain boundary vs. bulk conductivity. The features exhibited by these ceramics represent an increased potential to process solid electroceramics materials with specific levels of electronic and/or ionic conductivities for a variety of electrochemical devices.     

Phase stability and chemical composition dependence of the thermoelectric properties of the type-I clathrate Ba8AlxSi46−x (8≤x≤15)

Phase stability of the type-I clathrate compound Ba₈Al_xSi_46−x and the thermoelectric property dependence on chemical composition are presented. Polycrystalline samples were prepared by argon arc melting and annealing. Results of powder X-ray diffraction and electron microprobe analysis show that the type-I structure is formed without framework deficiency for 8≤x≤15. Lattice constant a increases linearly with the increase of x. Thermoelectric properties were measured for x=12, 14 and 15. The Seebeck coefficients are negative, with the absolute values increasing with x. The highest figure of merit zT=0.24 was observed for x=15 at T=1000 K, with carrier electron density n=3×10²¹ cm⁻³. A theoretical calculation based on the single parabolic band model reveals the optimum carrier concentration to be n∼4×10²⁰ cm⁻³, where zT∼0.7 at T=1000 K is predicted.     

Preparation and photoelectrocatalytic activity of a nano-structured WO3 platelet film

A tungsten trioxide (WO₃) film was prepared by calcination from a precursor paste including suspended ammonium tungstate and polyethylene glycol (PEG). The ammonium tungstate suspension was yielded by an acid-base reaction of tungstic acid and an ammonium solution followed by deposition with ethanol addition. Thermogravimetric (TG) analysis showed that the TG profile of PEG is significantly influenced by deposited ammonium tungstate, suggesting that PEG is interacting strongly with deposited ammonium tungstate in the suspension paste. X-ray diffraction (XRD) data indicated that the WO₃ film is crystallized by sintering over 400 °C. The scanning electron microscopic (SEM) measurement showed that the film is composed of the nano-structured WO₃ platelets. The semiconductor properties of the film were examined by Mott-Schottky analysis to give flat band potential E_FB=0.30 V vs. saturated calomel reference electrode (SCE) and donor carrier density N_D=2.5×10²² cm⁻³, latter of which is higher than previous WO₃ films by two orders of magnitude. The higher N_D was explained by the large interfacial heterojunction area caused by the nano-platelet structure, which apparently increases capacitance per a unit electrode area. The WO₃ film sintered at 550 °C produced 3.7 mA cm⁻² of a photoanodic current at 1.2 V vs. SCE under illumination with a 500 W xenon lamp due to catalytic water oxidation. This photocurrent was 4.5-12.8 times higher than those for the other control WO₃ films prepared by similar but different procedures. The high catalytic activity could be explained by the nano-platelet structure. The photocurrent was generated on illumination of UV and visible light below 470 nm, and the maximum incident photon-to-current conversion efficiency (IPCE) was 47% at 320 nm at 1.2 V. Technically important procedures for preparation of nano-structured platelets were discussed.