Pore Development during the Carbonization Process of Lignin Microparticles Investigated by Small Angle X-ray Scattering

Application of low-cost carbon black from lignin highly depends on the materials properties, which might by determined by raw material and processing conditions. Four different technical lignins were subjected to thermostabilization followed by stepwise heat treatment up to a temperature of 2000 °C in order to obtain micro-sized carbon particles. The development of the pore structure, graphitization and inner surfaces were investigated by X-ray scattering complemented by scanning electron microscopy and FTIR spectroscopy. Lignosulfonate-based carbons exhibit a complex pore structure with nanopores and mesopores that evolve by heat treatment. Organosolv, kraft and soda lignin-based samples exhibit distinct pores growing steadily with heat treatment temperature. All carbons exhibit increasing pore size of about 0.5–2 nm and increasing inner surface, with a strong increase between 1200 °C and 1600 °C. The chemistry and bonding nature shifts from basic organic material towards pure graphite. The crystallite size was found to increase with the increasing degree of graphitization. Heat treatment of just 1600 °C might be sufficient for many applications, allowing to reduce production energy while maintaining materials properties.     

Selective Utilization of the Methoxy Group in Lignin to Produce Acetic Acid

Selective transformation of lignin into a valuable chemical is of great importance and challenge owing to its complex structure. Herein, we propose a strategy for the transformation of methoxy group (‐OCH₃) which is abundant in lignin into pure highly valuable chemicals. As an example to apply this strategy, a route to produce acetic acid with high selectivity by conversion of methoxy group of lignin was developed. It was demonstrated that the methoxy group in lignin could react with CO and water to generate acetic acid over RhCl₃ in the presence of a promoter. The conversions of methoxy group in the kraft lignin and organosolv lignin reached 87.5 % and 80.4 %, respectively, and no by‐product was generated. This work opens the way to produce pure chemicals using lignin as the feedstock.     

Paving the Way for Lignin Valorisation: Recent Advances in Bioengineering,Biorefining and Catalysis

Lignin is an abundant biopolymer with a high carbon content and high aromaticity. Despite its potential as a raw material for the fuel and chemical industries, lignin remains the most poorly utilised of the lignocellulosic biopolymers. Effective valorisation of lignin requires careful fine‐tuning of multiple “upstream” (i.e., lignin bioengineering, lignin isolation and “early‐stage catalytic conversion of lignin”) and “downstream” (i.e., lignin depolymerisation and upgrading) process stages, demanding input and understanding from a broad array of scientific disciplines. This review provides a “beginning‐to‐end” analysis of the recent advances reported in lignin valorisation. Particular emphasis is placed on the improved understanding of lignin's biosynthesis and structure, differences in structure and chemical bonding between native and technical lignins, emerging catalytic valorisation strategies, and the relationships between lignin structure and catalyst performance.     

Selectively transform lignin into value-added chemicals

Selective transformation of lignin into value-added chemicals is of strategic significance. Phenols, aldehydes, carboxylic acids, alkanes and arenes can be harvested from lignin with high selectivity under appropriate reaction condition.     

Selective catalytic transformation of lignin with guaiacol as the only liquid product

Guaiacol is an important feedstock for producing various high-value chemicals. However, the current production route of guaiacol relies heavily on fossil resources. Using lignin as a cheap and renewable feedstock to selectively produce guaiacol has great potential, but it is a challenge because of its heterogeneity and inert reactivity. Herein, we discovered that La(OTf)₃ could catalyze the transformation of lignin with guaiacol as the only liquid product. In the reaction, La(OTf)₃ catalyzed the hydrolysis of lignin ether linkages to form alkyl-syringol and alkyl-guaiacol, which further underwent decarbonization and demethoxylation to produce guaiacol with a yield of up to 25.5 wt%, and the remaining residue was solid. In the scale-up experiment, the isolated yield of guaiacol reached up to 21.2 wt%. To our knowledge, this is the first work to produce pure guaiacol selectively from lignin. The bio-guaiacol may be considered as a platform to promote lignin utilization.

La(OTf)₃ can catalyze the transformation of lignin efficiently with guaiacol as the only liquid product, and guaiacol produced can be isolated easily in a scaled up experiment.     

Recombinant squalene synthase. Synthesis of non-head-to-tail isoprenoids in the absence of NADPH

Squalene synthase (SQase) catalyzes two consecutive reactions in sterol biosynthesis. The first is the condensation of two molecules of farnesyl diphosphate (FPP) to form a cyclopropylcarbinyl intermediate, presqualene diphosphate (PSPP). The subsequent conversion of PSPP to squalene (SQ) involves an extensive rearrangement of the carbon skeleton and a NADPH-dependent reduction. Incubation of a truncated soluble form of recombinant yeast SQase with FPP in buffer lacking NADPH gave (1R,2R,3R)-PSPP. As the incubation continued, SQase catalyzed the subsequent conversion of PSPP to a mixture of triterpenes. Two of the major products, (Z)-dehydrosqualene (DSQ) and (R)-12-hydroxysqualene (HSQ), have the same 1'-1 linkage between the farnesyl units from FPP that is found in squalene. The other major product, (10S,13S)-10-hydroxybotryococcene (HBO), has a 1'-3 linkage between the farnesyl units. Small quantities of (S)-HSQ and (10R,13S)-HBO were also formed. Three additional triterpenes, the allylic isomers of HSQ and HBO, and an unidentified alcohol were produced in minor amounts. A methyl ether corresponding to HSQ was detected when methanol was present in the incubation buffer. These compounds are the expected "solvolysis" products from PSPP. They provide strong support for mechanisms that propose cyclopropylcarbinyl cations as intermediates in the SQase-catalyzed rearrangement of PSPP to SQ and unambiguously demonstrate that the catalytic machinery of SQase is capable of synthesizing a variety of irregular isoprenoids.     

Eco-friendly composite resins based on renewable biomass resources: Polyfurfuryl alcohol/lignin thermosets

The properties of an innovative polyfurfuryl alcohol (PFA)/lignin combined matrix have been investigated. Furfuryl alcohol (FA) and lignin are, respectively, monomeric and polymeric precursors issued from biomass feedstock. In the present work, a plasticized lignin (PL) has been blended during polymerization of FA into PFA. Two kinds of samples were prepared at different FA/lignin ratio. Structural investigations were made on resins by ¹³C NMR while the thermo-mechanical performances of the combined materials were studied using thermogravimetric (TGA) and dynamic mechanical analysis (DMA). TGA results have permitted us to determine the thermal stability and the composition of the cured material on the basis of the ash content. According with these results, it was found that the lignin ratio in the cured material is more important than in the initial threshold. The TGA reveals that the PFA/PL thermo-oxidative degradation occurs at higher temperature compared to the natural (PL) component system, together with a lower rate of decomposition. This underlines a good interpenetration of lignin within the furanic matrix. The morphologies of the combined PFA/lignin systems, controlled by scanning electron microscopy (SEM), reveal a monophasic structure. These observations are in good agreement with the presence of a unique relaxation peak as shown in the DMA results.     

Changes in the structure of cell wall polymers in thermomechanical treatment of highly lignified plant feedstock

The effect of mechanical treatment at various temperatures on structural changes in polymers contained in highly lignified plant feedstock was studied by the example of reed stems. The optimal conditions (about 10°C) of mechanical activation of plant feedstock were determined, under which its structure is disordered enough for subsequent enzymatic hydrolysis, but the lignin decomposition is prevented, and so is the formation of a layer of substances inhibiting enzymes on the surface of particles.     

Lignin derived porous carbon with favorable mesoporous contributions for highly efficient ionic liquid-based supercapacitors

Lignin and its derivatives hold great potential in developing high performance porous carbon materials for supercapacitors due to the versatile features of high carbon content, abundant multifunctional groups, low cost, and environmental benefits. Unfortunately, their derived porous carbon generally has the features of unfavorable microporous-dominated morphologies and low specific surface area (SSA) attributed from the highly-branched structure of lignin, which are hardly suitable for the supercapacitors with ionic liquid (IL) electrolyte, leading to poor energy density and rate capability. Herein, porous carbon materials with desirable mesoporous contributions from sodium lignosulphonate are designed via a facile template method. Such rich mesoporisity carbon materials not only possess with three-dimensional interconnected network, large SSA, as well as favorable pore size distribution for accelerated ion and electron mass transfer, but also feature low heteroatom content for high electrochemical stability. Consequently, the optimal electrode exhibits a high capacitance of 166 F/g at 0.5 A/g, superior rate performance (59 Wh/kg at 59 kW/kg), as well as impressive cycle life with good capacitance retention of 93.1% in EMIBF₄ electrolytes. The present work opens a new avenue to design porous carbon materials with high mesopore properties from lignin for effective compatibility with IL electrolyte in high-performance supercapacitors.     

木质素降解模型化合物愈创木酚及苯酚原位加氢制备环己醇

以Raney Ni为催化剂,研究了甲醇水相重整制氢与木质素降解模型化合物愈创木酚／苯酚加氢的耦合反应.考察了反应前冷压、反应温度、反应时间、物料配比等条件对木质素降解模型化合物原位加氢反应性能的影响,并对影响机制进行了讨论.结果表明,在反应温度为220 ℃、反应前冷压0 MPa(表压)、物料比水／甲醇／模型化合物为20∶5∶0.8的条件下,反应7 h后愈创木酚转化率与环己醇选择性分别达99.00％和93.74％,反应12 h后苯酚的转化率与环己醇选择性分别达90.50％和99.29％.采用原位加氢反应,木质素降解的酚类模型化合物转化率和选择性明显优于外部供氢反应的转化率和选择性,同时,避免了外部供氢反应存在的氢气制备、储存、传输及加氢条件苛刻等问题,为木质素解聚产物制备化工品提供了新思路与实验基础.     

Recombinant squalene synthase. A mechanism for the rearrangement of presqualene diphosphate to squalene

Squalene synthase (SQase) catalyzes the condensation of two molecules of farnesyl diphosphate (FPP) to form presqualene diphosphate (PSPP) and the subsequent rearrangement and NADPH-dependent reduction of PSPP to squalene (SQ). These reactions are the first committed steps in cholesterol biosynthesis. When recombinant SQase was incubated with FPP in the presence of dihydroNADPH (NADPH3, an unreactive analogue lacking the 5,6-double bond in the nicotinamide ring), three products were formed: dehydrosqualene (DSQ), a C30 analogue of phytoene; 10(S)-hydroxysqualene (HSQ), a hydroxy analogue of squalene; and rillingol (ROH), a cyclopropylcarbinyl alcohol formed by addition of water to the tertiary cyclopropylcarbinyl cation previously proposed as an intermediate in the rearrangement of PSPP to SQ (Poulter, C. D. Acc. Chem. Res. 1990, 23, 70-77). The structure and absolute stereochemistry of the tertiary cyclopropylcarbinyl alcohol were established by synthesis using two independent routes. Isolation of ROH from the enzyme-catalyzed reaction provides strong evidence for a cyclopropylcarbinyl-cyclopropylcarbinyl rearrangement in the biosynthesis of squalene. By comparing the SQase-catalyzed solvolysis of PSPP in the absence of NADPH3 to the reaction in the presence of NADPH3, it is apparent that the binding of the cofactor analogue substantially enhances the ability of SQase to control the regio- and stereochemistry of the rearrangements of PSPP.     

低成本木质素吸附剂对废水中Pb2+吸附性能的研究

首次尝试以马尾松为原料的木质素制备低成本重金属吸附剂,采用N2物理吸附和红外漫反射技术对其结构和表面化学进行了表征,研究了pH值,温度对其吸附水溶液中Pb2 的影响,并与麦草木质素和商业活性炭进行了对比,探讨了它吸附重金属离子的吸附机理以及结构和表面化学对重金属离子吸附的影响。结果表明,马尾松木质素吸附剂对水溶液中Pb2 的吸附机理主要是化学吸附,其表面的功能基有利于吸附水溶液中Pb2 ,尽管商业活性炭的比表面积是马尾松碱木素的200多倍,在相同的实验条件下,所制备的马尾松碱木素对Pb2 的单位比表面积平衡吸附量却是商业活性炭的1000多倍。     

Effect of graphitization on the wettability and electrical conductivity of CVD-carbon nanotubes and films

The use of carbon nanomaterials in various applications requires precise control of their surface and bulk properties. In this paper, we present a strategy for modifying the surface chemistry, wettability, and electrical conductivity of carbon tubes and films through annealing in a vacuum. Experiments were conducted with 60-300 nm nanotubes (nanopipes), produced by noncatalytic chemical vapor deposition (CVD) in a porous alumina template, and with thin films deposited by the same technique on a glassy carbon substrate having the same structure and chemistry of the CNTs. The surface of the as-produced CVD-carbon, treated with sodium hydroxide to remove the alumina template, is hydrophilic, and the bulk electrical conductivity is lower by a factor of 20 than that of fully graphitic multiwalled nanotubes (MWNT) or bulk graphite. The bulk electrical conductivity increases to the conductivity of graphite after annealing at 2000 degrees C in a high vacuum. The analysis of CNTs by transmission electron microscopy (TEM) and Raman spectroscopy shows the ordering of carbon accompanied by an exponential increase of the in-plane crystallite size, L(a), with increasing annealing temperature. Environmental scanning electron microscopy (ESEM) was used to study the interaction of CNT with water, and contact angle measurements performed using the sessile drop method on CVD-carbon films demonstrate that the contact angle increases nearly linearly with increasing annealing temperature.     

Lipid Accumulation by Pelletized Culture of Mucor circinelloides on Corn Stover Hydrolysate

Microbial oil accumulated by fungal cells is a potential feedstock for biodiesel production, and lignocellulosic materials can serve as the carbon source to support the fungal growth. The dilute acid pretreatment of corn stover can effectively break down its lignin structure, and this process generates a hydrolysate containing mostly xylose at very dilute concentration and numerous by-products that may significantly inhibit the cell growth. This study utilized corn stover hydrolysate as the culture media for the growth of Mucor circinelloides. The results showed that Mucor cells formed pellets during the cell growth, which facilitates the cell harvest from dilute solution. The results also showed that the inhibitory effect of furfural, 5-hydroxymethylfurfural (HMF), and acetic acid could be avoided if their concentration was low. In fact, all these by-products may be assimilated as carbon sources for the fungal growth. The results proved the feasibility to reuse the cultural broth water for acid pretreatment and then use for subsequent cell cultivation. The results will have a direct impact on the overall water usage of the process.     

Two high-throughput techniques for determining wood properties as part of a molecular genetics analysis of hybrid poplar and loblolly pine

Two new high-through put techniques, computer tomography X-ray densitometry (CT scan) and pyrolysis molecular beam mass spectrometry (pyMBMS), coupled with quantitative trait loci (QTL) analysis, were tested as a means to overcome the time and cost associated with conventional characterization of biomass feedstock components. Applications of these two techniques were evaluated using hybrid poplar for the CT scan and loblolly pine for the pyMBMS. Segregating progeny from hybrid poplar varied in specific gravity, with individual mean estimates ranging from 0.21–0.41. Progeny from loblolly pine varied in lignin, α cellulose, and mannan contents, with individual mean estimates of lignin content ranging from 28.7–33.1%, α cellulose content from 28.8–43.5% and mannan content from 4.2–10.1%. QTL analysis of the loblolly pine data suggested that eleven QTLs were associated with individual feedstock characteristics and that two QTLs for several feedstock components were linked to the same position on the loblolly pine genetic map. Each QTL individually accounted for 7–13% of the total phenotypic variation in associated loblolly pine feedstock components.     

The influence of thermo-hygro-mechanical treatment on the micro- and nanoscale architecture of wood cell walls using small- and wide-angle X-ray scattering

Tracking the changes of cellulose crystallites upon thermo-hygro-mechanical treatment is essential to understand the response of wood cell walls to steam and compression. In this paper the influence of Compression combined with Steam (CS) treatment on wood cellulose crystallites and pores structure of Chinese fir (Cunninghamia lanceolata) was studied under different steaming temperatures and compression ratios. Small-angle X-ray scattering and wide-angle X-ray scattering were used to investigate the changes of cellulose crystallites dimension, aspect ratio, fibril diameter distribution, non-crystalline fraction, the number of chains in each microfibril, as well as the fractal dimension and size of pores in response to CS treatment conditions. Results indicate that the crystallinity increased due to CS treatment, but did not show alteration with varying CS treatment conditions, i.e. seemed nearly unaffected by higher temperatures or compression ratio, both for earlywood and latewood. The cellulose crystallite diameter depended on processing parameters: it increased with increasing treatment temperature. No considerable differences were found for earlywood and latewood. We interpret our findings as a rearrangement of adjacent cellulose chains towards higher crystalline perfection attributing to the increase in crystallinity. The same effect allows a larger coherence length of crystalline order and therefore features an increasing cross-sectional dimension. In general we can state that the CS treatment leads to higher crystallinity and more perfectly arranged cellulose crystals, while it does not greatly affect the microfibril diameter but rather the amorphous regions of the microfibrils and the surrounding hemicellulose and lignin.     

Relationship between formation conditions, properties, and crystallite size of boehmite

Boehmites (gamma-AlOOH) with a variety of crystallite sizes were prepared under various precipitation conditions from solutions of aluminum nitrate and sodium aluminate and also by hydrothermal treatment of a commercial boehmite powder. The relationships between the crystallite size and other properties of the boehmites were investigated. Crystalline boehmite was formed in the pH range 7 to 10 while gels precipitated below pH 7 and bayerite (Al(OH)3) formed at pH 11. The crystallite size of the boehmite increased at higher pH, higher temperature of the precursor solution, and longer aging time. As the crystallite size of the boehmite increased, the specific surface area, pore volume, and excess water decreased. Boehmites of small crystallite size, called pseudoboehmite, showed broadened X-ray peak widths and increased d-spacing of the 020 reflection. These changes are attributed to the small crystallite size (smaller numbers of stacking layers) and also to excess water in the interlayers of the boehmite structure.     

Increased Saccharification Yields from Aspen Biomass Upon Treatment with Enzymatically Generated Peracetic Acid

The recalcitrance of lignocellulosic biomass to enzymatic release of sugars (saccharification) currently limits its use as feedstock for biofuels. Enzymatic hydrolysis of untreated aspen wood releases only 21.8% of the available sugars due primarily to the lignin barrier. Nature uses oxidative enzymes to selectively degrade lignin in lignocellulosic biomass, but thus far, natural enzymes have been too slow for industrial use. In this study, oxidative pretreatment with commercial peracetic acid (470 mM) removed 40% of the lignin (from 19.9 to 12.0 wt.% lignin) from aspen and enhanced the sugar yields in subsequent enzymatic hydrolysis to about 90%. Increasing the amount of lignin removed correlated with increasing yields of sugar release. Unfortunately, peracetic acid is expensive, and concentrated forms can be hazardous. To reduce costs and hazards associated with using commercial peracetic acid, we used a hydrolase to catalyze the perhydrolysis of ethyl acetate generating 60–70 mM peracetic acid in situ as a pretreatment to remove lignin from aspen wood. A single pretreatment was insufficient, but multiple cycles (up to eight) removed up to 61.7% of the lignin enabling release of >90% of the sugars during saccharification. This value corresponds to a predicted 581 g of fermentable sugars from 1 kg of aspen wood. Improvements in the enzyme stability are needed before the enzymatically generated peracetic acid is a commercially viable alternative.     

Effects of ultra-high temperature treatment on the microstructure of carbon fibers

The microcrystalline structure and microvoid structure in carbon fibers during graphitization process(2300-2700 °C) were characterized employing laser micro-Raman scattering(Raman), X-ray diffraction(XRD), small angle X-ray scattering(SAXS), and high-resolution transmission electron microscopy(HR-TEM). The crystalline sizes(L_a, L_c) increased and interlayer spacing(d_(002)) decreased with increasing heat treatment temperature(HTT). The microvoids in the fibers grew up and contacted to the neighbors with the development of microcrystalline. In addition, the preferred orientation of graphite crystallite along fiber axis decreased and microvoids increased. The results are crucial for analyzing the evolution of microstructure of carbon fibers in the process of heat treatment and important for the preparation of high strength and high modulus carbon fibers.     

Fabrication of polyacrylonitrile/lignin-based carbon nanofibers for high-power lithium ion battery anodes

Low-cost carbon nanofibers are fabricated from lignin, the second most abundant raw material in wood after cellulose and polyacrylonitrile mixture as a carbon precursor by electrospinning, followed by suitable heat treatments. As the lignin content in the precursor increases, the carbon nanofibers become thinner, as seen from scanning electron microscopy images. However, their carbon structure and electrochemical performance are found to be very similar, even though surface functional groups on carbon nanofibers are slightly different from each other. For example, in the initial charge (lithium insertion) and discharge (lithium deinsertion) process, the reversible specific capacities of the various carbon nanofibers come from different precursor ratios of lignin and polyacrylonitrile are similar. Even at a fast (7 min) charge and discharge condition, the carbon nanofibers prepared from the lignin-containing precursors show a discharge capacity of 150 mAh g^?1. The lignin-based carbon nanofibers thus show promise for use in high-power lithium ion battery anodes with low price.