表面修饰纳米TiO2的贮氢合金电极的光充电行为

Nanocrystalline anatase-type TiO2 was prepared by the hydrolysis-precipitaiton method, the rare earth hydrogen storage alloys were modified with the as-prepared TiO2 and the photocharging behavior, and cyclic voltammetry curves and EIS spectra were measured. The experimental results show that the potential has little shift under the light irradiation for the unmodified electrode. However, for the TiO2 modified electrode, a remarkable shift of the potential to negative direction (up to -0.835 V) takes place under the light irradiation, which means the generation of H atom on the electrode surface under the light irradiation. The EIS results also indicate that there exists the absorption of H atom and the following diffusion of H atom into the hydrogen storage alloys under the light irradiation. The FEM observations on the electrode surface show that a large amount of microcracks appear on the electrode surface. These microcracks may be induced by the bulk expansion when the generated hydrogen atoms were absorbed by the hydrogen storage alloys.     

新型CNT/nano-TiO_2复合膜电极的制备及其异相电催化性能

采用溶胶-凝胶法制备了碳纳米管/纳米TiO2(CNT/nano-TiO2)复合溶胶,通过提拉法将复合溶胶涂覆在Ti基体上制得CNT/nano-TiO2复合膜修饰电极(C电极),其电化学性能经循环伏安、计时库仑、交流阻抗谱(EIS)等方法研究.研究结果表明,CNT可阻碍nano-TiO2粒子团聚.在循环伏安图中,C电极的氧化还原峰电流比nano-TiO2膜修饰电极(P 电极)的高出两倍多.通过对草酸溶液的异相电催化反应进一步证明C电极比P电极具有更高的电催化活性,而且对双氧水也有很强的异相电催化还原能力.     

Fe2O3/TiO2纳米管的制备及其光电催化降解染料废水性能

采用阴极电沉积和阳极氧化法制备了Fe2O3改性TiO2纳米管(Fe2O3/TiO2-NTs)电极,运用场发射扫描电子显微镜、透射电子显微镜、X射线衍射和紫外-可见漫反射光谱等手段对其进行了表征,考察了其光电化学性能,并研究了复合电极光电催化降解甲基橙染料废水的反应性能.结果表明,Fe2O3的负载成功地将TiO2-NTs的光响应区间拓宽到可见光区域,Fe2O3/TiO2-NTs复合电极的光电流密度达到TiO2-NTs电极的3倍.在光电催化反应中,Fe2O3/TiO2-NTs复合电极对甲基橙的脱色效果明显优于TiO2-NTs电极,以Fe2O3/TiO2-NTs为阳极,光照5min,甲基橙溶液的脱色率可达90%以上.     

Influence of Modification of Counter Electrode on Photoelectric Properties of Dye-sensitized TiO2 Solar Cells

A dye-sensitized nanocrystalline TiO2 solar cell(DYSC) was assembled, of which counter electrode was modified already by platinum, nickel and carbon. It was found that the DYSC had better photoelectric performance when the electrode was modified by platinum than by nickel and carbon. The influence of the incidence light wavelength on the incidence monochromatic photoelectric conversion effieieney(IPCE) was investigated.The result shows that the IPCE mainly depends on the short-circuit current density(Isc) of a DYSC, and the IPCE reaches 48.32% under the irradiation with the wavelength of 560 nm when the counter electrode of a DYSC was modified by platinum. The influence of incident light intensity on the photoelectric properties of a DYSC was also investigated. It was found that the Isc and open-circuit voltage(Voc) increased and the fill factor(ff) of the DYSC decreased with the increase of the incident light intensity.     

Glassy carbon electrode modified with poly-Neutral Red for photoelectrocatalytic oxidation of NADH

A new approach is described for the photoelectrocatalytic oxidation of Reduced ß-Nicotinamide Adenine Dinucleotide (NADH). It is based on a glassy carbon electrode (GCE) modified with a film of poly-Neutral Red (poly-NR) that is obtained by electropolymerization. Electrochemical measurements revealed that the modified electrode displays electrocatalytic and photo-electrocatalytic activity towards oxidation of NADH. If irradiated with a 250-W halogen lamp, the electrode yields a strongly increased electrocatalytic current compared to the current without irradiation. Amperometric and photo-amperometric detection of NADH was performed at +150 mV vs. Ag/AgCl/KCl_sat and the currents obtained are linearly related to the concentration of NADH. Linear calibration plots are obtained in the concentration range from 1.0 μM to 1.0 mM for both methods. However, the slope of the current-NADH concentration curve of the photo-electrocatalytic procedure was 2-times better than that obtained without irradiation.

聚3-甲基噻吩修饰量子点硫化铅连接TiO2纳米结构膜的光电化学研究

采用原位化学法在纳米结构TiO2电极上制备了量子点PbS(Q-PbS), 并用电化学方法在TiO2/Q-PbS表面聚合3-甲基噻吩[poly(3-Methylthiophene), PMeT]. 研究结果表明, PMeT和Q-PbS单独修饰纳米结构TiO2电极和PMeT修饰Q-PbS连接纳米结构TiO2电极的光电流产生的起始波长都向长波方向移动; 在可见光区光电转换效率均比纳米结构TiO2的光电转换效率提高显著; PMeT与Q-PbS修饰的纳米结构TiO2之间存在p-n异质结. 在一定条件下p-n异质结的存在有利于光生电子/空穴的分离, 提高了光电转换效率.     

聚3-甲基噻吩修饰硫化物量子点连接纳米结构TiO2膜的光电化学研究

采用原位化学法在纳米结构TiO₂膜上制备了量子点CdS, PbS (Q-CdS, Q-PbS), 并用电化学方法在TiO₂/Q-CdS, TiO₂/Q-PbS表面聚合3-甲基噻吩[poly(3-Methylthiophene, PMeT)]. 用光电化学方法研究了PMeT修饰Q-CdS, Q-PbS连接TiO₂纳米结构膜, 实验结果表明, PMeT和Q-CdS, Q-PbS单独修饰纳米结构TiO₂电极和PMeT修饰Q-CdS, Q-PbS连接纳米结构TiO₂电极的光电流产生的起始波长都向长波方向移动; 一定条件下在可见光区光电转换效率均较纳米结构TiO₂的光电转换效率有明显的提高; 聚3-甲基噻吩(PMeT)与Q-CdS, Q-PbS连接的纳米结构TiO₂之间存在p-n异质结. 在一定条件下p-n异质结的存在有利于光生电子/空穴的分离, 在本文实验条件下PMeT修饰Q-CdS, Q-PbS连接纳米结构TiO₂电极最高的单色光的光电转换效率分别为11%和7%.     

Enhanced Photoelectrochemical Property of Zn Loaded TiO2 Nanotube Arrays Electrode

TiO₂ nanotube arrays (TNTs) electrode loaded with Zn nanoparticles was prepared by anodization and the size of Zn nanoparticle loaded on TNTs electrode was controlled bychronoamperometry deposition time. Results of SEM and XRD analysis show that Zn nanoparticles had a diameter of about 15-25 nm when the deposition time was 3-5 s. The UV-Vis diffuse reflectance spectra show the Zn loaded harvest light with 480-780 nm more effectively than the unloaded sample. The photocurrent response of Zn loaded TNTs electrodes were studied, the results showed that TNTs electrodes loaded with Zn nanoparti-cles has 50% increased photocurrent response under high-pressure mercury lamp irradiation compared with unloaded TNTs electrode.     

聚次甲基蓝修饰玻碳电极测定叶酸

利用循环伏安法将次甲基蓝修饰到玻碳电极表面,制备了聚次甲蓝修饰电极(PMB/GCE),并研究了此电极的化学性质及对叶酸的电化学响应特性.在磷酸盐缓冲液中PMB/GCE电极对叶酸有良好的催化作用并出现一个灵敏的还原峰,用循环伏安法测得峰电流与叶酸的浓度在0.1×10-3～2.9×10 -3 mol/L范围内呈良好线性关系...     

金属卟啉与Keggin型硅钨酸修饰电极的制备及电催化性能测定

运用自组装和电化学组装联用方法,将镍卟啉配合物THPPNi和Keggin型硅钨酸SiW₁₂修饰到玻碳电极上,制备镍卟啉修饰电极和镍卟啉/硅钨酸复合修饰电极,研究其在DMF溶液中的电化学行为,测定在碱性条件下对NO₂^-和BrO₃^-的电催化性能。循环伏安和交流阻抗研究结果表明,复合修饰电极THPPNi/SiW₁₂的电极过程属于扩散控制过程;复合修饰电极优于单一修饰金属卟啉和多酸修饰电极。     

紫外光下纳米TiO2 薄膜亲水性机理的电化学研究

The nanometer films of TiO2 were prepared by sol-gel method on ITO（Indium-tin oxide,SnO2:In） substrate. The TiO2 film was the anatase phase with a particle size of 100 nm from the measurements of X-ray diffraction and AFM（Atomic-Force-Microscope）. Electrochemical characteristics of ITO/ TiO2 electrode under UV（ultraviolet）irradiation were investigated using the method of cyclic voltammetry. A new oxidative peak was observed at 0.035 V when the TiO2 electrode was irradiated by 253.7 nm UV light for a certain time. The peak current increased with the irradiation time. It was assumed that the new oxidative peak resulted from Ti3+,which was formed during the UV illumination. The changes of hydrophilicity of the TiO2 thin film on ITO under UV light were also observed. It was assumed that the changes of hydrophilicity of the films may be related with the formation of Ti3+ on the surface when the film was irradiated by UV light.     

石墨烯/铂纳米粒子杂化膜测定肾上腺素

利用循环伏安法制备了石墨烯/铂纳米粒子杂化膜修饰电极,并利用该修饰电极研究了肾上腺素（EP）的电化学行为,建立了测定肾上腺素的电化学方法。 分别利用扫描电子显微镜（SEM）和循环伏安法对电极表面的形貌和电化学性能进行了表征。 试验优化了修饰电极制备过程中影响电极性能的条件和EP的测定条件。 试验结果表明,石墨烯/铂纳米粒子修饰电极对肾上腺素有明显的电催化作用。 在pH=5.0的柠檬酸 磷酸氢二钠缓冲溶液中,EP的氧化峰电流与其浓度在4.4×10-8~2.2×10-6 mol/L的范围内呈良好的线性关系。 线性方程为ipa(10 μA)=0.0753c(mol/L)+3.7653×10-5,r=0.9989,检出限为2.2×10-9 mol/L（S/N=3）。 修饰电极表具有良好的重现性,可用于实际样品的测定。     

A thin layer photocell based on a tris(2,2'-bipyridine)ruthenium complex immobilized in a membrane containing an electronically conductive polymer

A thin layer photocell was constructed in which tin oxide (Nesa glass) modified with a tris(2,2'-bipyridine)ruthenium complex immobilized in a polyvinylcinnamate membrane was used as the working electrode, platinum was used as the counter electrode, and an aqueous solution containing the disodium salt of ethylenediaminetetraacetic acid was placed between the electrodes. The photocell generated a photocurrent under visible light irradiation. The generation of photocurrent was considerably enhanced when the working electrode was modified by the addition of the tetracyanoquinodimethane salt of poly-4-vinylpyridine and neutral tetracyanoquinodimethane.     

光敏型季铵盐类阳离子表面活性剂的合成及表面活性和泡沫性质

本文报道了一种光敏型的阳离子表面活性剂（AZO），其分子结构中含有偶氮苯基团，并研究了光照对表面活性和泡沫性能的影响。经紫外光照射后，表面活性剂的饱和吸附量（Г_max）减小，临界胶束浓度（cmc）、最低表面张力（γ_cmc）和分子极限占有面积（A_min）增大；气泡数目增多，直径变小，发泡能力和泡沫稳定性降低。实验结果证实，该表面活性剂的表面活性和泡沫稳定性可以用光照进行调控。     

有机钌螯合物/TiO_2杂化膜修饰电极上Pt纳米团簇的光电流增强效应

利用LB膜技术可控制备了纳米单层和多层的二氧化钛-有机钌螯合物杂化膜,并研究了上述无机-有机杂化膜修饰电极在Pt纳米团簇敏化后的光电流增强效应.实验结果表明:(1)纳米单层TiO2/[Ru(phen)2(dC18bpy)]2+(简称为TiO2-Ru)杂化膜的平均厚度为(3.6±0.5)nm;(2)在光照条件下TiO2-Ru杂化膜能有效催化还原[Pt(NH3)6]4+形成粒径位于20～160nm之间的Pt纳米团簇;(3)Pt纳米团簇的引入消除了金属钌螯合物中配体对电子传递的阻碍作用,改变了电子传递途径,从而有效减少了电子空穴对的复合,提高了Pt纳米团簇敏化的n层杂化膜修饰电极(ITO/(TiO2-Ru)n/Pt)在支持电解质中的光电流.与纳米单层TiO2-Ru杂化膜修饰的ITO电极(ITO/TiO2-Ru)相比,当工作电压为900mV时,ITO/TiO2-Ru/Pt在0.1mol·L-1的NaClO4电解质溶液中和光照(λ360nm)条件下,单位面积的光电流提高了约5倍;(4)ITO/(TiO2-Ru)n/Pt电极光电流的大小与杂化膜的层数密切相关,当TiO2-Ru杂化膜的层数从一层、二层增加到四层时,光电流呈现先升高后下降行为,这表明ITO/(TiO2-Ru)n/Pt电极的电子传递过程直接通过非电活性的二氧化钛纳米单层进行.     

Synthesis and characterization of a p-type boron arsenide photoelectrode

A p-type boron arsenide photoelectrode was prepared from a material consisting of a thin layer of boron arsenide on a boron substrate. The structure of the material was identified using X-ray diffraction and scanning electron microscopy, and the surface composition was determined by means of X-ray photoelectron spectroscopy. The electrode was found to be photoactive under both visible light and UV-vis irradiation and displayed a photocurrent of ~0.1 mA/cm(2) under UV-vis irradiation at an applied potential of -0.25 V vs Ag/AgCl. Mott-Schottky plots for this boron arsenide electrode displayed an estimated flat-band potential near the onset photopotential. The estimated indirect band gap, as determined from incident photon-to-electron conversion efficiency plots, is 1.46 ± 0.02 eV.     

基于纳米CdS对尿酸的光催化氧化和铜(Ⅱ)配合物对氧的电催化还原的燃料电池性能

以纳米硫化镉薄膜修饰的铟锡氧化物电极(CdS/ITO)作光阳极, 铜(Ⅱ)配合物[Cu(phen)(L-Trp)·(H₂O)]⁺(phen=1,10-菲啰啉, L-Trp=L-色氨酸)修饰单壁碳纳米管(SWCNTs)电极作阴极, 构建了光催化尿酸(UA)燃料电池, 并研究了其性能及热处理温度的影响. 结果表明, 在40 ℃以下获得的纳米CdS修饰电极在320~550 nm波长区间显现明显的吸收和光伏响应, 在可见光辐射下能光催化氧化UA; 较高温度的热处理(200~300 ℃)却降低了纳米CdS对UA的光催化氧化活性. [Cu(phen)(L-Trp)(H₂O)]⁺/SWCNTs电极在-0.131 V电位下呈现一对准可逆的氧化还原峰, 并能电催化还原O₂和H₂O₂. 此外, 基于UA在CdS/ITO电极上的光催化氧化及O₂在[Cu(phen)(L-Trp)(H₂O)]⁺/SWCNTs电极上的电催化还原, 组装了UA(0.2 mmol/L)燃料电池, 其在可见光照射(0.18 mW/cm²)下产生0.52 V开路电压, 13.08 μA/cm²短路光电流, 在0.41 V下呈现的最大功率密度为4.10 μW/cm².     

羧基化石墨烯基导电聚吡咯复合材料的超电容性能

制备了羧基化石墨烯基聚吡咯复合物(CG/ppy）修饰电极,用循环伏安法和交流阻抗法研究了修饰电极的电化学行为,并对修饰电极进行了恒流充放电以及循环稳定性测试。 实验结果表明,CG/ppy显著提高了玻碳电极在电解液中的电流响应,降低了玻碳电极在电解液中的电阻,修饰电极的比电容可达584 F/g,且经过1000次循环后比电容仍保持初始值的81%。 首次将羧基化石墨烯基聚吡咯应用于电化学领域,证实了CG/ppy修饰电极在该领域中有潜在的应用价值。     

射频磁控溅射制备纳米TiO2薄膜的光电化学行为

在室温下采用射频磁控溅射法制备了纳米晶粒的TiO2薄膜,用循环伏安法研究了ITO/TiO2薄膜电极的光电化学行为,并测量了相应TiO2薄膜的亲水性与光催化能力.结果表明,在室温下制备的TiO2薄膜为无定形结构,当退火温度超过400 ℃时转化为锐钛矿结构.在400 ℃下退火的TiO2薄膜具有良好的亲水性和光催化能力. TiO2薄膜电极用254 nm的紫外光照射一定时间后会产生新的氧化峰,且随着光照时间的增加,峰电流也增加.初步认为用紫外光照射一定时间后, TiO2薄膜的循环伏安图的氧化峰属于光生的Ti3＋,而光致亲水性可能与Ti3＋的生成有关.     

Synthesis of molecular imprinted polymer modified TiO2 nanotube array electrode and their photoelectrocatalytic activity

A tetracycline hydrochloride (TC) molecularly imprinted polymer (MIP) modified TiO₂ nanotube array electrode was prepared via surface molecular imprinting. Its surface was structured with surface voids and the nanotubes were open at top end with an average diameter of approximately 50 nm. The MIP-modified TiO₂ nanotube array with anatase phase was identified by XRD and a distinguishable red shift in the absorption spectrum was observed. The MIP-modified electrode also exhibited a high adsorption capacity for TC due to its high surface area providing imprinted sites. Photocurrent was generated on the MIP-modified photoanode using the simulated solar spectrum and increased with the increase of positive bias potential. Under simulated solar light irradiation, the MIP-modified TiO₂ nanotube array electrode exhibited enhanced photoelectrocatalytic (PEC) activity with the apparent first-order rate constant being 1.2-fold of that with TiO₂ nanotube array electrode. The effect of the thickness of the MIP layer on the PEC activity was also evaluated.