Side chain length affects backbone dynamics in poly(3‐alkylthiophene)s

Charge transport in conjugated polymers may be governed not only by the static microstructure but also fluctuations of backbone segments. Using molecular dynamics simulations, we predict the role of side chains in the backbone dynamics for regiorandom poly(3‐alkylthiophene‐2,5‐diyl)s (P3ATs). We show that the backbone of poly(3‐dodecylthiophene‐2‐5‐diyl) (P3DDT) moves faster than that of poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) as a result of the faster motion of the longer side chains. To verify our predictions, we investigated the structures and dynamics of regiorandom P3ATs with neutron scattering and solid state NMR. Measurements of spin‐lattice relaxations (T₁) using NMR support our prediction of faster motion for side chain atoms that are farther away from the backbone. Using small‐angle neutron scattering (SANS), we confirmed that regiorandom P3ATs are amorphous at about 300 K, although microphase separation between the side chains and backbones is apparent. Furthermore, quasi‐elastic neutron scattering (QENS) reveals that thiophene backbone motion is enhanced as the side chain length increases from hexyl to dodecyl. The faster motion of longer side chains leads to faster backbone dynamics, which in turn may affect charge transport for conjugated polymers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1193–1202     

Crystallization mechanism of regioregular poly(3‐alkyl thiophene)s

The crystallization properties of three regioregular poly(3‐alkyl thiophene)s (P3ATs) are studied: poly(3‐hexyl thiophene) (P3HT), poly(3‐octyl thiophene) (P3OT), and poly(3‐dodecyl thiophene) (P3DDT). The morphology of the isothermally crystallized samples is a whisker type. The values of the enthalpy of fusion of ideal crystals (ΔH), determined from the melting point depression in the polymer–diluent system, are 99, 73.6, and 52 J/g for P3HT, P3OT, and P3DDT, respectively. The values of the equilibrium melting point (T), determined from the Hoffman–Weeks extrapolation procedure, are 300, 230, and 180 °C for P3HT, P3OT, and P3DDT, respectively. From the linear extrapolation of the P3AT data, the T and ΔH values of unsubstituted polythiophene are predicted to be 400 °C and 139 J/g, respectively. The crystallization kinetics of these polymers are studied with differential scanning calorimetry, and the Avrami exponents vary between 0.6 and 1.4, indicating one‐dimensional heterogeneous nucleation with linear growth. As the P3AT whiskers are produced from the chain‐folding process, the Lauritzen–Hoffman growth rate theory is applied to analyze the temperature coefficient of the crystallization rate data. Graphical plots indicate a transition from regime I to regime II during isothermal crystallization for all the P3ATs studied. The fold surface energy and the work of chain folding calculated from the slopes of the graphical plots decrease with an increase in the number of carbon atoms of the side chain. The primary crystallization process of the side‐chain crystallization is very fast and is attributed to the zipping effect of the main‐chain crystals. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2073–2085, 2002     

Thermal stability of P3HT and P3HT:PCBM blends in the molten state

The thermal stability of poly(3-hexylthiophene) (P3HT) in its molten state was investigated in air and nitrogen atmospheres under no illumination conditions, with the aim of testing the feasibility of processing it using polymer melt techniques. A large set of different experimental characterization techniques was used including thermogravimetric analysis (TGA), rotational rheometry, infrared spectroscopy (FTIR-ATR), proton nuclear magnetic resonance spectroscopy (¹H-NMR), gel permeation chromatography (GPC), UV-Vis and fluorescence spectroscopy. The results obtained strongly suggest that the processing of P3HT in its molten state is possible, without noticeable degradation, if carried out under nitrogen atmosphere and if the processing (residence) times are relatively short. Conversely, as expected, in a normal air atmosphere P3HT degrades rapidly at temperatures above its melting point. The effect of PCBM on the thermal stability of P3HT:PCBM blends in the molten state was also studied using TGA, and in air atmosphere PCBM is shown to delay oxidation.     

Synthesis of all‐conjugated poly(3‐hexylthiophene)‐block‐ poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) and its blend for photovoltaic applications

New all‐conjugated block copolythiophene, poly(3‐hexylthiophene)‐block‐poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) (P3HT‐b‐P3PyT) was successfully prepared by Grignard metathesis polymerization. The supramolecular interaction between [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and P3PyT was proposed to control the aggregated size of PCBM and long‐term thermal stability of the photovoltaic cell, as evidenced by differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and optical microscopy. The effect of different solvents on the electronic and optoelectronic properties was studied, including chloroform (CL), dichlorobenzene (DCB), and mixed solvent of CL/DCB. The optimized bulk heterojunction solar cell devices using the P3HT‐b‐P3PyT/PCBM blend showed a power conversion efficiency of 2.12%, comparable to that of P3HT/PCBM device despite the fact that former had a lower crystallinity or absorption coefficient. Furthermore, P3HT‐b‐P3PyT could be also used as a surfactant to enhance the long‐term thermal stability of P3HT/PCBM‐based solar cells by limiting the aggregated size of PCBM. This study represents a new supramolecular approach to design all‐conjugated block copolymers for high‐performance photovoltaic devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Microstructural behavior and failure mechanisms of organic semicrystalline thin film blends

Organic thin film blends of P3HT semiconducting polymers and PCBM fullerenes have enabled large‐scale semiconductor fabrication pertaining to flexible and stretchable electronics. However, molecular packing and film morphologies can significantly alter mechanical stability and failure behavior. To further understand and identify the fundamental mechanisms affecting failure, a multiphase microstructurally based formulation and nonlinear finite‐element fracture methodology were used to investigate the heterogeneous deformation and failure modes of organic semicrystalline thin film blends. The multiphase formulation accounts for the crystalline and amorphous behavior, polymer tie‐chains, and the PCBM aggregates. Face‐on packing orientations resulted in extensive inelastic deformation and crystalline rotation, and this was characterized by ductile failure modes and interfacial delamination. For edge‐on packing orientations, brittle failure modes and film cracking were due to lower inelastic deformation and higher film stress in comparison with the face‐on orientations. The higher crystallinity of P3HT and larger PCBM aggregates associated with larger domain sizes, strengthened the film and resulted in extensive film cracking. These predictions of ductile and brittle failure are consistent with experimental observations for P3HT:PCBM films. The proposed predictive framework can be used to improve organic film ductility and strength through the control of molecular packing orientations and microstructural mechanisms. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 896–907     

Vinyl‐Type Polynorbornenes with Pendant PCBM: A Novel Acceptor for Organic Solar Cells

Vinyl addition homo‐ and copolymerization of norbornene monomer ( M1 ) functionalized with a PCBM moiety using a Pd(II) catalyst in combination with a 1‐octene chain transfer agent efficiently produces polynorbornenes with side‐chain PCBM groups. Characterization by NMR spectroscopy and elemental analysis reveals that the copolymers constitute a well‐defined polymer structure with controlled incorporation of M1 . Although the homopolymer is insoluble in organic solvents, the copolymers containing 62 mol% ( P2 ) and 50 mol% ( P3 ) of the PCBM moiety are soluble in chlorinated solvents such as o‐dichlorobenzene. The bulk‐heterojunction organic photovoltaic devices fabricated based on the P3HT: P3 blends show that P3 can adequately function as an electron acceptor, leading to a cell with a power conversion efficiency of 1.5%, which is outstanding among the polymeric rivals.     

Ternary Donor–Insulator–Acceptor Systems for Polymer Solar Cells

A series of block copolymers with fixed length of the semiconductor‐block poly(3‐butylthiophene) (P3BT) and varying length of the insulator‐block polystyrene (PS) are synthesized. These copolymers are blended with phenyl‐C61‐butyric acid methyl ester (PCBM) for the bulk heterojunction photoactive layers. With appropriate insulator‐block length and donor–acceptor ratio, the power conversion efficiency increases by one order of magnitude compared with reference devices with pure P3BT/PCBM. PS blocks improve the miscibility of the active layer blends remarkably. The P3BT‐b‐PS crystallizes as nanorods with the P3BT core covered with the PS‐block, which creates a nanoscale tunneling barrier between donor and acceptor leading to more efficient transportation of charge carriers in the semiconductors.     

A novel donor–donor polymeric dyad of Poly(3‐hexylthiophene‐block‐oligo(anthracene‐9,10‐diyl): Synthesis,solid‐state packing,and electronic properties

A new polymeric dyad of oligo‐anthracene‐block‐poly(3‐hexylthiophene) (Oligo‐ANT‐b‐P3HT) has been synthesized as a donor–donor dyad building block for organic photovoltaics. The polymer dyad and oligomer of anthracene‐9,10‐diyl (Oligo‐ANT) are prepared by Grignard Metathesis. The higher order of crystallinity and molecular chains ordering at solid phase reveal the intrinsic optical and electrical properties of polymeric dyad resulting in relatively higher light harvesting ability compared to the oligo(anthracene‐9,10‐diyl). The UV‐visible spectrum of (Oligo‐ANT‐b‐P3HT) in solution shows broad absorption with two sets of absorption from both anthracene and thiophene core units, covering a wide range of the visible spectrum. The test devices of the blends of polymeric dyad with fullerene C₆₁ (PCBM) show improved photovoltaic performance with a power conversion efficiency of 3.26% upon subjecting to pre‐fabrication thermal treatments. With optimized morphology of the interpenetrating network and the shorter fluorescence lifetime of the annealed dyad/PCBM blends, the effective charge transfer from the donor dyad to PCBM has evidenced. Thus, these studies will allow further synthetic advances to make potential high crystalline polymeric dyads with significantly improved light harvesting capability. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3032–3045     

Regioregularity and solar cell device performance of poly(3‐dodecylthienylenevinylene)

Influence of side chain regioregularity on photovoltaic performance has been investigated in bulk heterojunction solar cells based on a series of poly(3‐dodecylthienylenevinylene)s (C₁₂‐PTV) and 6,6‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM). Performance of each C₁₂‐PTV is optimized for fair comparison. It is found that regiorandomness has no detrimental effect on device performance, in sharp contrast to poly(3‐hexylthiophene) (P3HT). Fully regioregular C₁₂‐PTV performs slightly poorer than less regioregular ones mainly due to its fast crystallization behavior. The results suggest that introduction of side chain regiorandomness is an effective strategy to enhance processability of certain types of polymers without a reduction in photovoltaic performance. The better polymer:PCBM weight ratio, found to be 3:7 for all C₁₂‐PTVs, and improved device performance, as compared with the literature work on the same polymer synthesized by a different method, demonstrate again the importance of the integrity of polymer main chain structure. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Quantifying the efficiency of förster‐assisted optical gain in semiconducting polymer blends by excitation wavelength selective amplified spontaneous emission

We study the correlation between Förster resonance energy transfer (FRET) and optical gain properties in conjugated polymer blends based on regioregular poly(3‐hexylthiophene) (P3HT) and poly(9,9‐dioctylfluorene‐alt‐benzothiadiazole) (F8BT). First, FRET dynamics are investigated with femtosecond transient absorption spectroscopy observing a sub‐picosecond energy transfer from F8BT to P3HT (550 fs) at medium doping levels (40% wt P3HT in F8BT). Amplified spontaneous emission (ASE) is then characterized in blends upon exciting predominantly the host and guest polymers, respectively. The corresponding density of absorbed photons at threshold conditions is compared upon host or guest photoexcitation as a method to quantitatively determine the FRET‐assisted ASE efficiencies. We observe a reduction in ASE efficiency upon host photoexcitation of 20%, in the best case, respect to guest photoexcitation. Our results confirm that even in strongly coupled host:guest mixtures delayed exciton population by energy transfer is subtle to losses ascribed to exciton–exciton annihilation. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2311–2317.     

Enhanced properties of photovoltaic devices tailored with novel supramolecular structures based on reduced graphene oxide nanosheets grafted/functionalized with thiophenic materials

For verifying the influence of donor–acceptor supramolecules on photovoltaic properties, different hybrids were designed and used in organic solar cells. In this respect, reduced graphene oxide (rGO) was functionalization with 2‐thiophene acetic acid (rGO‐f‐TAA) and grafted with poly(3‐dodecylthiophene) (rGO‐g‐PDDT) and poly(3‐thiophene ethanol) (rGO‐g‐PTEt) to manipulate orientation of poly(3‐hexylthiophene) (P3HT) assemblies. Face‐on, edge‐on, and flat‐on orientations were detected for assembled P3HTs on rGO and its functionalized and grafted derivatives, respectively. Alteration of P3HT orientation from face‐on to flat‐on enhanced current density (J _sc), fill factor (FF), and power conversion efficiency (PCE) and thus J _sc = 7.11 mA cm^?2, FF = 47%, and PCE = 2.14% were acquired. By adding phenyl‐C71‐butyric acid methyl ester (PC71BM) to active layers composed of pre‐designed P3HT/rGO, P3HT/rGO‐f‐TAA, P3HT/rGO‐g‐PDDT, and P3HT/rGO‐g‐PTEt hybrids, photovoltaic characteristics further improved, demonstrating that supramolecules appropriately mediated in P3HT:PC71BM solar cells. Phase separation was more intensified in best‐performing photovoltaic systems. Larger P3HT crystals assembled onto grafted rGOs (95–143 nm) may have acted as convenient templates for the larger and more intensified phase separation in P3HT:PCBM films. The best performances were reached for P3HT:P3HT/rGO‐g‐PDDT:PCBM (J _sc = 9.45 mA cm^?2, FF = 54%, and PCE = 3.16%) and P3HT:P3HT/rGO‐g‐PTEt:PCBM (J _sc = 9.32 mA cm^?2, FF = 53%, and PCE = 3.11%) photovoltaic systems. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 1877–1889     

Conformational change,intrachain aggregation and photophysical properties of regioregular poly(3‐octylthiophene) in alkanes

This study explores the role of segmental solubility of regioregular poly(3‐octylthiophene) (rr‐P3OT) on chain organization and its photophysical properties. In good solvent chlorobenzene (CRB), rr‐P3OT chain adopts an extended conformation, allowing long conjugation length of π‐electrons. Cyclohexane is a good solvent for octyl side chain but a poor solvent for the thiophene backbone. The selective segmental interactions of rr‐P3OT with this solvent induce conformational change of the polymer. Addition of cyclohexane into the CRB solution leads to chain coiling, which in turn causes significant decrease of the conjugation length. Absorption and photoluminescence spectra of the rr‐P3OT in cyclohexane exhibit a blueshift of about 16 nm compared to those of the CRB solution. The change of chain conformation is also detectable by monitoring the variation of quantum yield upon increasing cyclohexane ratio. The quantum yield drops from 0.17 ± 0.01 to 0.11 ± 0.01 when the extended rr‐P3OT chain transforms into coiled conformation. Hexane is a nonsolvent for rr‐P3OT due to its relatively low solubility parameter. The addition of hexane into rr‐P3OT solution in cyclohexane forces dense packing of thiophene rings within the coiled chain. An intrachain aggregation occurs in this system, leading to the appearance of three distinct redshift peaks in absorption spectra and the drastic drop of quantum yield. Correlation between the growth of redshift peaks and the decrease of quantum yield is clearly observed. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1288–1297     

Effects of amorphous poly(3‐hexylthiophene) on active‐layer structure and solar cells performance

A key challenge to the development of polymer‐based organic solar cells is the issue of long‐term stability, which is mainly caused by the unstable time‐dependent morphology of active layers. In this study, poly(3‐hexylthiophene) (P3HT)/[6,6]‐phenyl C60‐butyric acid methyl ester (PCBM) blend is used as a model system to demonstrate that the long‐term stability of power conversion efficiency can be significantly improved by the addition of a small amount of amorphous regiorandom P3HT into semicrystalline regioregular one. The optical properties measured by UV–vis absorption and photoluminescence reveal that regiorandom P3HT can intimately mix with PCBM and prevent the segregation of PCBM. In addition, X‐ray scattering techniques were adopted to evidence the retardation of phase separation between P3HT and PCBM when regiorandom P3HT is added, which is further confirmed by optical microscopy that shows a reduction of large PCBM crystals after annealing at high temperature in the presence of regiorandom P3HT. The improvement of the long‐term stability is attributed to the capability of amorphous P3HT to be thermodynamically miscible with PCBM, which allows the active layer to form a more stable structure that evolves slower and hence decelerates the device decay. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 975–985     

Solvent‐Dependent Structure Formation in Drying P3HT:PCBM Films Studied by Molecular Dynamics Simulations

Phase separation in the donor‐acceptor blend poly(3‐hexylthiophene‐2,5‐diyl):[6,6]‐phenyl‐C61‐butyric acid methyl ester (P3HT:PCBM) during evaporation of a solvent using coarse‐grained molecular dynamics simulations is studied here. To this end, an equilibrated P3HT:PCBM:solvent mixture is placed in an elongated simulation box, after which solvent molecules are removed at regular time intervals from a region above the film. Three often‐used solvents are considered: chloroform (CFM), chlorobenzene (CLB), and orthodichlorobenzene (oDCB). The coarse‐grained solvent–solvent interaction parameters are tuned to reproduce the atmospheric boiling temperatures, while the PCBM–solvent interaction parameters are tuned to reproduce the PCBM solubilities. Other parameters are taken from the literature. During evaporation, the formation of a crust that is depleted of solvent, in which aggregation of P3HT and PCBM occurs, is observed. In agreement with experiment, the top region of the dry film is rich in PCBM for the cases of CLB and oDCB, and rich in P3HT for the case of CFM, while the very top layer of the film is always rich in P3HT. This vertical separation is ascribed to a competition between the tendency of P3HT to move to the surface due to its low surface energy and the different tendencies of PCBM to be dragged along to the surface by the evaporating solvent depending on its solubility. Also in agreement with experiment, the P3HT–PCBM interface area is larger for CLB and oDCB than for CFM. For CLB and oDCB, an indication for a spinodal P3HT–PCBM decomposition starting from the top and bottom surface is found, whereas for CFM the phase separation appears to be initiated in the bulk of the film.

     

Phase behavior of PCBM blends with different conjugated polymers

In this work the phase behavior of [6,6]-phenyl C(61)-butyric acid methyl ester (PCBM) blends with different poly(phenylene vinylene) (PPV) samples is investigated by means of standard and modulated temperature differential scanning calorimetry (DSC and MTDSC) and rapid heat-cool calorimetry (RHC). The PPV conjugated polymers include poly(2-methoxy-5-(3',7'-dimethyloctyloxy)-1,4-phenylene vinylene) (MDMO-PPV), High T(g)-PPV which is a copolymer, and poly((2-methoxy-5-phenethoxy)-1,4-phenylene vinylene) (MPE-PPV). Comparisons of these PPV:PCBM blends with regioregular poly(3-hexyl thiophene) (P3HT):PCBM blends are made to see the different component miscibilities among different blends. The occurrence of liquid-liquid phase separation in the molten state of MDMO-PPV:PCBM and High T(g)-PPV:PCBM blends is indicated by the coexistence of double glass transitions for blends with a PCBM weight fraction of around 80 wt%. This is in contrast to the P3HT:PCBM blends where no phase separation is observed. Due to its high cooling rate (about 2000 K min(-1)), RHC proves to be a useful tool to investigate the phase separation in PPV:PCBM blends through the glass transition of these crystallizable blends. P3HT is found to have much higher thermal stability than the PPV samples.     

How to measure absolute P3HT crystallinity via 13C CPMAS NMR

We outline the details of acquiring quantitative ¹³C cross‐polarization magic angle spinning (CPMAS) nuclear magnetic resonance on the most ubiquitous polymer for organic electronic applications, poly(3‐hexylthiophene) (P3HT), despite other groups' claims that CPMAS of P3HT is strictly nonquantitative. We lay out the optimal experimental conditions for measuring crystallinity in P3HT, which is a parameter that has proven to be critical in the electrical performance of P3HT‐containing organic photovoltaics but remains difficult to measure by scattering/diffraction and optical methods despite considerable efforts. Herein, we overview the spectral acquisition conditions of the two P3HT films with different crystallinities (0.47 and 0.55) and point out that because of the chemical similarity of P3HT to other alkyl side chain, highly conjugated main chain polymers, our protocol could straightforwardly be extended to other organic electronic materials. Variable temperature ¹H NMR results are shown as well, which (i) yield insight into the molecular dynamics of P3HT, (ii) add context for spectral editing techniques as applied to quantifying crystallinity, and (iii) show why T_1ρ^H, the ¹H spin–lattice relaxation time in the rotating frame, is a more optimal relaxation filter for distinguishing between crystalline and noncrystalline phases of highly conjugated alkyl side‐chain polymers than other relaxation times such as the ¹H spin–spin relaxation time, T₂^H, and the spin–lattice relaxation time in the toggling frame, T_1xz^H. A 7 ms T_1ρ^H spin lock filter, prior to CPMAS, allows for spectroscopic separation of crystalline and noncrystalline ¹³C nuclear magnetic resonance signals. Published 2016. This article is a U.S. Government work and is in the public domain in the USA.     

RAFT polymerization kinetics and polymer characterization of P3HT rod–coil block copolymers

Here an in‐depth analysis of reversible addition–fragmentation chain transfer (RAFT) polymerization kinetics is reported in order to provide better definition of poly(3‐hexylthiophene) (P3HT) rod–coil block copolymers thru a more thorough understanding of the RAFT polymerization of the coil block. To this end, a new P3HT macroRAFT agent is synthesized and utilized to prepare rod–coil block copolymers with P3HT and poly(styrene), poly(tert‐butylacrylate), and poly(4‐vinylpyridine), and the RAFT polymerization kinetics of each system are fully detailed. This is achieved by a comprehensive analysis of characterization data from ¹H nuclear magnetic resonance spectroscopy, gel permeation chromatography, and matrix‐assisted laser desorption ionization time of flight spectroscopy, which are used as complementary techniques in order to address difficulties in accurately characterizing the synthesized polymer systems. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3575–3585     

Conjugated block copolymers via functionalized initiators and click chemistry

Conjugated block copolymers are potentially useful for organic electronic applications and the study of interfacial charge and energy transfer processes; yet few synthetic methods are available to prepare polymers with well‐defined conjugated blocks. Here, we report the synthesis and thin film morphology of a series of conjugated poly(3‐hexylthiophene)‐block‐poly(9,9‐dioctylfluorene) (P3HT‐b‐PF) and poly(3‐dodecylthiophene)‐block‐poly(9,9‐dioctylfluorene) (P3DDT‐b‐PF) block copolymers prepared by functional external initiators and click chemistry. Functional group control is quantified by proton nuclear magnetic resonance spectroscopy, size‐exclusion chromatography, and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. The thin film morphology of the resulting all‐conjugated block copolymers is analyzed by a combination of grazing‐incidence X‐ray scattering, atomic force microscopy, and transmission electron microscopy. Crystallization of the P3HT or P3DDT blocks is present in thin films for all materials studied, and P3DDT‐b‐PF films exhibit significant PF/P3DDT co‐crystallization. Processing conditions are found to impact thin film crystallinity and orientation of the π–π stacking direction of polymer crystallites. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 154–163     

Annealing effect on performance and morphology of photovoltaic devices based on poly(3‐hexylthiophene)‐b‐poly(ethylene oxide)

Novel block copolymers, poly(3‐hexylthiophene)‐b‐poly(ethylene oxide) (P3HT‐b‐PEO) were synthesized via Suzuki coupling reaction of P3HT and PEO homopolymers. The copolymers were characterized by NMR, gel permeation chromatography, differential scanning calorimeter, and UV–vis measurements. A series of devices based on the block copolymers with a fullerene derivative were evaluated after thermal or solvent annealing. The device using P3HT‐b‐PEO showed higher efficiency than using P3HT blend after thermal annealing. Phase‐separated structures in the thin films of block copolymer blends were investigated by atomic force microscopy to clarify the relationship between morphologies constructed by annealing and the device performance. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

末端功能基团对聚（3-丁基噻吩）光电性能的影响

研究了4种带有不同末端基团的聚(3-丁基噻吩)(P3BT)的光电性能。结果表明,末端基团对P3BT的结晶有一定的抑制作用,可以改变P3BT的表面能,从而有效调控P3BT∶PCBM共混体系相容性以及薄膜的形貌,并影响以P3BT为给体材料的聚合物光伏器件的性能。其中,带有较短烷基链末端基团的烯丙基封端P3BT具有较高的结晶性,与PCBM具有适中的相容性,使得光伏器件的光敏层能够形成理想的微相分离结构,器件效率可以达到3.1%,较传统的溴封端P3BT器件效率提升35%以上。