Ba0.6Sr0.4TiO3/聚偏氟乙烯-聚甲基丙烯酸甲酯复合材料的制备及其介电性能

采用流延热压工艺制备Ba_0.6Sr_0.4TiO₃(BST)/聚偏氟乙烯(PVDF)?聚甲基丙烯酸甲酯(PMMA)复合薄膜,研究了PMMA含量对复合材料微观组织结构和介电性能的影响规律。结果表明,BST相能够均匀分散在聚合物基体中,归因于PMMA与PVDF良好的相容性,2种聚合物之间的界面不分明;随着PMMA含量的增加,复合材料的介电常数先降低后升高,耐击穿强度和介电可调性先增加后减少。PMMA含量(体积分数)为15%的BST/PVDF?PMMA₁₅复合材料的综合性能最佳:介电常数为23.2,介电损耗为0.07,耐击穿强度为1412 kV·cm^-1,在550 kV·cm^-1偏压场下,介电可调性为26.2%。     

PMMA-SiO<Subscript>2</Subscript> organic–inorganic hybrid films: determination of dielectric characteristics

Organic–inorganic hybrid thin films have been prepared by a modified sol–gel route using tetraethyl orthosilicate as the inorganic (silica) source, methyl methacrylate (MMA) as the organic source, and 3-trimetoxysilylpropyl methacrylate as the coupling agent. The films were prepared by spin coating on Si (100) p-type substrates and subsequently heat-treated at 90 °C. Fourier transform infrared results reveal a set of absorption bands associated with the formation of both PMMA and SiO₂ phases in the hybrid films. Capacitance–voltage (C–V) characterization was carried out on metal-insulator-metal (MIM) and metal-insulator-semiconductor (MIS) structures, with the hybrid films as the insulator layer to evaluate the electrical properties. We present a detailed comparative analysis of the dielectric constant obtained from C–V characterization in the frequency range of 1 kHz–1 MHz. For the PMMA-SiO₂ hybrid material the dielectric constant values obtained were around 9.5 at 1 MHz which is superior to the values reported for thermally grown SiO₂ and pure PMMA materials. The interface state density for PMMA-SiO₂ on Si was approximately 10¹⁰ cm⁻², which is comparable to the standard SiO₂/Si structures. Due to the electrical behavior and low processing temperatures this hybrid dielectric is a very promising candidate for flexible electronic devices and its subsequent implementation does not require complex equipment.     

The investigation of the friction and wear properties of surface‐treated carbon fiber/SiO2 reinforced PMMA composites

The mechanical properties of SiO₂ filler particles on carbon fibers have been under discussion for several decades; the diverse models, and the properties of the components relevant to retention, are critically reviewed in the first part of this study. In addition, to gain an insight into some possible combined effect of the carbon fiber/poly(methyl methacrylate) (CF/PMMA), interfacial adhesion strength and the tensile properties and dielectric strength of the hybrid composites were studied. Simple modified rules of mixtures are used to estimate the fiber efficiency factors for the strength and modulus of the hybrid composites. Except, with the increasing fraction of CFs in PMMA, the weld line area's elongation percent is decreased. Whereas for case of SiO₂, the 10 wt% is the threshold for micro injection molded weld line tensile strength and dielectric strength turning from decrease trend to increase. Same as CF, elongation of micro weld line samples is in general lower than neat PMMA as well, due to the addition of SiO₂ particles.     

Swift heavy ion induced modification in dielectric and microhardness properties of polymer composites

Polymer composites with different concentrations of organometallics (ferric oxalate) dispersed PMMA were prepared. PMMA was synthesized by solution polymerization technique. These films were irradiated with 120 MeV Ni¹⁰⁺ ions in the fluence range 10¹¹-5 × 10¹² ions/cm². The radiation induced modifications in dielectric properties, microhardness, structural changes and surface morphology of polymer composite films have been investigated at different concentrations of filler and ion-fluences. It was observed that electrical conductivity and hardness of the films increase with the concentration of the filler and also with the fluence. The dielectric constant (?) obeys the Universal law given by ?αfⁿ⁻¹. The dielectric constant/loss is observed to change significantly due to irradiation. This suggests that ion beam irradiation promotes the metal to polymer bonding and convert polymeric structure into hydrogen depleted carbon network. This makes the composites more conductive and harder. Surface morphology of the films has been studied using atomic force microscopy (AFM) and scanning electron microscopy (SEM). The average surface roughness is observed to increase after irradiation as revealed by AFM studies. The SEM images show the blisters type of phenomenon on the surface due to ion beam irradiation.     

Ion Beam Modification of Polymethyl methacrylate (PMMA) Polymer Matrix Filled with Organometallic Complex

A Nickel Dimethylglyoxime (Ni‐DMG) compound was dispersed in polymethyl methacrylate (PMMA) films at different concentrations. PMMA was synthesized by a solution polymerization technique. These films were irradiated with 120 MeV Ni¹⁰⁺ ions at the fluences of 1×10¹¹ and 1×10¹² ions/cm². The radiation induced changes in dielectric properties and average surface roughness were investigated by using an LCR meter in the frequency range 50 Hz to 10 MHz and atomic force microscopy (AFM), respectively. The electrical properties of irradiated films are found to increase with the fluence and also with the concentration of Ni‐DMG. From the analysis of frequency, f, dependence of dielectric constant, ?, it has been found that the dielectric response in both pristine and irradiated samples obey the Universal law given by ? α f ^n?1. The dielectric constant/loss is observed to change significantly due to the irradiation. This suggests that ion beam irradiation promotes (i) the metal to polymer bonding (ii) convert the polymeric structure in to hydrogen depleted carbon network due to the emission of hydrogen gas and/or other volatile gases. Atomic force microscopy (AFM) shows that the average surface roughness and surface morphology of irradiated films are observed to change.     

PMMA: A key macromolecular component for dielectric low-κ hybrid inorganic-organic polymer films

Inorganic-organic composite and hybrid films find widespread applications for the development of functional materials. Polymer matrices with embedded inorganic fillers, nanoparticles or clusters are particularly appealing for optical, electronic, dielectric and magnetic applications. In particular, the development of hybrid layers with tailored dielectric properties represents a key issue in many technological fields.In this framework, poly(methyl methacrylate) (PMMA), due to its outstanding chemico-physical properties, represents a particularly suitable polymer component for the embedding of both microscopic and nanoscopic functional inorganic fillers. The wide use of such a matrix has to be traced back to the favourable combination of chemical and physical properties and easy processing. In this review, the main features and properties of PMMA, with a particular focus on dielectric ones, are firstly briefly described. Selected examples to illustrate the state-of-the art of its corresponding use as dielectric matrix are given and several examples are provided and surveyed.Finally, three case studies concerning PMMA-based hybrid films, produced for very different application fields, are described and discussed. The first example deals with the entrapment of micrometric zinc sulphide powders in PMMA, which acts as a host matrix for the electroluminescent particles in thick film-based Alternate Current Powder Electroluminescent Lamps (ACPELs). The second example describes the preparation of low-κ inorganic-organic hybrid dielectric films based on a PMMA-polyvinylchloride(PVC) blend and a hydrophobic silica powder functionalised on the surface with trimethylsiloxane groups (m-SiO₂). The composition of the investigated materials is [(PMMA)_x(PVC)_y]/(m-SiO₂)_z with z ranging from 0 to 38.3 wt% and x = y = (100 − z)/2. The third case concerns the use of PMMA as a matrix to embed zirconium oxoclusters through the formation of covalent bonds. The obtained material, characterised by a dielectric constant value remarkably lower (1.93 at 1 kHz and 25 °C) than in pristine PMMA (3.0 at 1 kHz and 25 °C), appears as very appealing for the development of microelectronic devices based on low dielectric constant polymer films such as, for instance, field-effect transistor (FET).These three cases are paradigms of three different approaches to composite and hybrid materials based on the embedding of particles in PMMA polymer matrix.     

Dielectric properties of stereoregular poly(methyl methacrylates)

To obtain more useful information about the effect of the degree of stereoregularity on the motion of the polymer chain, the dielectric and dilatometric measurements were made for a series of stereoregular poly(methyl methacrylates) (PMMA). The α- and β-absorptions were observed in each sample, of which the dielectric behaviors of the α-process are discussed. The temperature dependence of the relaxation time of the α-process was sufficiently represented by the WLF equation and the resulting values of the parameters f_g and B in the modified WLF equation were found smaller for isotactic-rich PMMA than those values for syndiotactic PMMA. It may be deduced from these results that the chain mobility of the isotactic PMMA is larger than that of the syndiotactic. The dielectric increment of the α-process in the isotactic PMMA is much larger than that in the syndiotactic PMMA, increasing rapidly with temperature, and taking its maximum in the temperature range of 55 to 60°C. The dielectric transition was clearly observed in the case of isotactic-rich PMMA.     

Dielectric properties of sols of silver nanoparticles capped by alkyl carboxylate ligands

Sols of silver nanoparticles in toluene were studied by broadband dielectric spectroscopy (10⁻³–10⁵ Hz). The frequency dependences of the specific alternating current (ac) conductivity and the complex electric modulus were used to estimate the temperature/frequency intervals of long- and short-range charge transfer occurs, respectively. A considerable increase (by more than 30 °C) in the Vogel temperature T ₀ and the glass transition temperature T _g in sols compared with the pure solvent was found. It can be hypothesized that these cooperative effects reflect the initial stage of the superlattice formation. Although the dielectric characteristics of sols are generally controlled by the conductivity relaxation, the dielectric response was observed in the high-frequency range (1–10³ Hz) at low temperatures (from −50 to +10 °C). This response results from the presence of nanoparticles in solution. It is supposed that the relaxation is caused by the motion of ion impurities on the Ag nanoparticle surface within the carboxylate ligands shell. The dielectric properties of films strongly depend on both the characteristics of nanoparticles and the conditions of the film preparation. Like in sols, the direct current (dc) conductivity and the dielectric response of Ag nanoparticles in films are due to ion impurities.     

Ion transport and relaxation in phosphonium poly(ionic liquid) homo- and co-polymers

In the present work, a poly(ionic liquid) (PIL), poly(triphenyl-4-vinylbenzylphosphonium chloride) and a series of its random copolymers with nonionic hydrophobic poly(methyl methacrylate) (PMMA) are synthesized by conventional free radical polymerization (CFRP) and reversible addition-fragmentation chain-transfer (RAFT) polymerization. The understanding of some fundamental aspects about ion transport and relaxation mechanism in PIL and PIL copolymers are investigated using dielectric spectroscopy via several theoretical models. The influence of copolymer compositions, physical blending of neat PIL and PMMA, size of counter anions (Cl⁻ and TFSI⁻) and variation of molecular weights on thermal stability, moisture sensitivity, ionic transport and relaxation properties are also studied. An enhancement of thermal stability and ionic transport property of the PIL copolymer is observed compared to those of the physically mixed blend of two homopolymers with same compositions. The incorporation of hydrophobic PMMA segment definitely decreases the moisture content in PIL copolymers than the PIL itself. In all these PIL- based systems, the temperature dependence of ionic conductivity, relaxation time and ion diffusivity are well described by Vogel-Tammann-Fulcher model. The studies of some fundamental properties of these new PIL copolymers with less moisture sensitivity may help in using them as potential polymer electrolytes in energy storage devices.     

Evaluation of the (Allyl alcohol 1,2‐butoxylate‐block‐etoxylate)‐b‐PMMA Copolymers Composition by the Dielectric Measurements

Redox initiated free‐radical polymerization of methyl methacrylate (MMA) with allyl alcohol 1,2‐butoxylate‐block‐etoxylate (AABE) was carried out to yield AABE‐b‐PMMA copolymers at elevated temperatures. The composition of the copolymers depending on the polymerization temperature was qualitatively estimated by the dielectric measurements. It has been seen that AABE segment quantity decreased and PMMA segment quantity increased with increasing the polymerization temperature. The dielectric constant and the dissipation factor of the copolymers were investigated as a function of frequency and temperature. The dielectric constant and the dissipation factor were found to be strongly affected by the polymerization temperature. The highest dielectric constant in all studied temperatures and frequencies was obtained in the case of the copolymer which was prepared at 313 K. The dipolar C‐O and OH groups of the AABE segment have the primary effect on the dielectric constant. The copolymer which was prepared at 323 K, showed the highest dissipation factor near the relaxation temperature of PMMA.     

Effects of Supporting Electrolytes on Spectroelectrochemical and Electrochromic Properties of Polyaniline‐poly(styrene sulfonic acid) and Poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid)‐based Electrochromic Device

Electrochromic devices are fabricated by using polyaniline (PANI) doped with poly(styrene sulfonic acid) (PSS) as coloring electrodes, poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid) (PEDOT‐PSS) as complementary electrodes, and hybrid polymer electrolytes as gel electrolytes. The device based on LiClO₄‐based electrolyte (weight ratio of PMMA:PC:LiClO₄ = 0.7:1.1:0.3) shows the highest optical contrast and coloration efficiency (333 cm²/C) after 1200 cycles in these devices, and the color changes from pale yellow (?0.5 V) to dark blue (+2.5 V). The spectroelectrochemical and electrochromic switching properties of electrochromic devices are investigated, the maximum optical contrast (ΔT%) of electrochromic device for ITO|PANI‐PSS‖PMMA‐PC‐LiClO₄‐SiO₂‖PEDOT‐PSS|ITO are 31.5% at 640 nm, and electrochromic device based on LiClO₄‐based electrolyte with SiO₂ shows faster response time than that based on LiClO₄‐based electrolyte without SiO₂.     

Interphase/interface modification on the dielectric properties of polycarbonate/poly(vinylidene fluoride‐co‐hexafluoropropylene) multilayer films for high‐energy density capacitors

Unique three‐component multilayer films with ATBTATBTA configuration were fabricated using forced assembly multilayer coextrusion for novel dielectric systems. The dielectric breakdown strength, displacement–electric field hysteresis, and dielectric spectroscopy of 65‐layer polycarbonate (PC)/tie/poly(vinylidene fluoride‐co‐hexafluoropropylene) (P(VDF‐HFP)) were investigated with various tie materials. Three different tie materials, poly(methyl methacrylate) (PMMA), styrene‐co‐acrylonitrile copolymer with 30% acrylonitrile content (SAN30), and poly(ethylene terephthalate‐co‐1,4‐cycohexanedimethylene terephthalate) (PETG) were chosen owing to their various degrees of interaction with either P(VDF‐HFP) or PC. The 65‐layer PC/PMMA/P(VDF‐HFP) films exhibited a 25% enhancement in breakdown properties, 50% higher energy density, 40% smaller hysteresis loop areas, and orders of magnitude slower ion migration relative to the 33‐layer PC/P(VDF‐HFP) control. These property improvements are mainly attributed to the localized interactions at PMMA/P(VDF‐HFP) and PMMA/PC interfaces, forming interphase regions. The modified PMMA/P(VDF‐HFP) interphase region can effectively hinder the migration of impurity ions in P(VDF‐HFP), reducing their mobility within the layer. Additionally, a small fraction of PMMA can lead to slightly increased dielectric constant of the composite films owing to strong interaction between PMMA and P(VDF‐HFP). The other two systems with PETG and SAN30 as tie layers exhibited marginal improvements in dielectric properties owing to their weaker interactions with the P(VDF‐HFP) layers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 978–991     

Bi3+/Ce3+ doped ZnO nanoparticles with enhanced photocatalytic and dielectric properties

In this study, varying % Bi-doped on 1% Ce-doped ZnO (1CZ) nanoparticles (X% B-1CZ) were synthesized via a facile, simple, low-cost, sol–gel process. Various characterization techniques were employed to characterize the synthesized compound, while the dielectric properties i.e. dielectric constant, dielectric loss and AC conductivity against frequency were studied with the help of a precision impedance analyzer. It was observed that by increasing bismuth content in the nanoparticles, the dielectric constant also increased in the range (1.47 × 10⁶ – 4.02 × 10⁶) at 20 Hz, and vice versa for dielectric loss decreased from 1.05 × 10⁶ to 0.39 × 10⁶. The role of prepared compounds as photocatalysts was also investigated against methylene blue under ultraviolet irradiation. The degradation efficiency, as well as the dielectric properties of 7% Bi-doped on 1% Ce-doped ZnO (7%B-1CZ), were found to be the best. Overall, it was found that the synthesized compounds proved promising candidates with enhanced photocatalytic & dielectric properties and hence could safely be employed for environmental remediation purposes and energy storage devices.     

Light-scattering studies on polystyrenes in isorefractive poly(methyl methacrylate)–toluene “solvents”

The rms radii of gyration 〈S²〉^1/2 and second virial coefficients Γ₂ of five monodisperse polystyrenes (M × 10^?5 = 1.6, 2.8, 4.2, 6.6) were measured in isorefractive toluene–poly(methyl methacrylate) (M?_v = 4.0 × 10⁴, 1.6 × 10⁵, and 6.3 × 10⁵) “solvents.” For a given PMMA, the concentration at which the θ condition (defined by Γ₂ = 0) was reached was independent of PS molecular weight, but varied inversely with PMMA molecular weight (0.10, 0.056, and 0.023 g/mL, respectively). When this θ condition is reached by adding PMMA to toluene, the radii of gyration are decreased by only about 15%, much less than when it is reached by going to a poor, low-molecular-weight solvent. This reflects the exclusion of PMMA from the PS coils, the internal environment of which is essentially pure toluene.     

Effects of concentration of nonionic surfactant and molecular weight of polymers on the morphology of anisotropic polystyrene/poly(methyl methacrylate) composite particles prepared by solvent evaporation method

The effects of the concentration of polyoxyethylene octylphenyl ether (OP-10) as a nonionic surfactant and the molecular weight of polymers (polystyrene (PS) and poly(methyl methacrylate) (PMMA)) on the morphology of anisotropic PS/PMMA composite particles were investigated. In the case of polymers with lower molecular weight (M _w ≈ 6.0 × 10⁴ g/mol), the PS/PMMA composite particles have dimple, via acorn, to hemispherical shapes along with the increase of the OP-10 concentration. On the other hand, when the polymers have higher molecular weight (M _w ≈ 3.3 × 10⁵ g/mol), the morphology of PS/PMMA composite particles changed from dimple, via hemispherical, to snowman-like structure while the concentration of OP-10 was increased. Furthermore, thermodynamic analysis was first simply made by spreading coefficients, and the results indicated that both the concentration of OP-10 aqueous solution and the molecular weight of polymers were very important to the final morphology of anisotropic composite particles.     

Surfactant-induced electroosmotic flow in microfluidic capillaries

Control of EOF in microfluidic devices is essential in applications such as protein/DNA sizing and high‐throughput drug screening. With the growing popularity of poly(methyl methacrylate) (PMMA) as the substrate for polymeric‐based microfludics, it is important to understand the effect of surfactants on EOF in these devices. In this article, we present an extensive investigation exploring changes in EOF rate induced by SDS, polyoxyethylene lauryl ether (Brij35) and CTAB in PMMA microfluidic capillaries. In a standard protein buffer (Tris‐Glycine), PMMA capillaries exhibited a cathodic EOF with measured mobility of 1.54 ± 0.1 (× 10^?4 cm²/V.s). In the presence of surfactant below a critical concentration, EOF was independent of surfactant concentration. At high concentrations of surfactants, the electroosmotic mobility was found to linearly increase/decrease as the logarithm of concentration before reaching a constant value. With SDS, the EOF increased by 257% (compared to buffer), while it was decreased by 238% with CTAB. In the case of Brij35, the electroosmotic mobility was reduced by 70%. In a binary surfactant system of SDS/CTAB and SDS/Brij35, addition of oppositely charged CTAB reduced the SDS‐induced EOF more effectively compared to nonionic Brij35. We propose possible mechanisms that explain the observed changes in EOF and zeta potential values. Use of neutral polymer coatings in combination with SDS resulted in 50% reduction in the electroosmotic mobility with 0.1% hydroxypropyl methyl cellulose (HPMC), while including 2% poly (N,N‐dimethylacrylamide) (PDMA) had no effect. These results will potentially contribute to the development of PMMA‐based microfluidic devices.     

Adsorption of toluene-soluble polymers at the toluene–water interface

The adsorption of several toluene-soluble polymers at the toluene–water interface has been investigated by using the duNouy ring method of measuring interfacial tension γT /W . Polystyrene and poly(ethylene-co-vinyl acetate) (11.1 mole-% vinyl acetate) have little affinity for this interface at 29°C, but poly(methyl methacrylate) (PMMA) (M?_n = 420,000) and ethyl cellulose (EC) (M?_n = 50,100; 49.1% ethoxyl) adsorb significantly at concentrations as low as 1.0 × 10^?4 g/100ml. A plot of interfacial tension lowering versus initial logarithm of initial bulk phase polymer concentration is linear from 1.0 × 10^?4 to 1.0 × 10^?1 g/100 ml for EC and 1.0 × 10^?4 to 1.0 × 10^?2 g/100 ml for PMMA. When the PMMA concentration increases to 1.15 × 10^?1 g/100 ml, its adsorption behavior changes markedly. Prolonged time effects occur and adsorption becomes dependent upon dissolved water content of the toluene prior to formation of the toluene/water interface. Such effects are not observed with the other solutions studied. Increasing temperatures have variable effects on values of γT /W for the polymer solutions studied. Experiments with various polymer mixtures indicate that the polymer lowering T /W the most is preferentially adsorbed at the toluene–water interface and rapidly displaces less strongly adsorbed polymers.     

Effect of potassium permanganate on morphological,structural and electro-optical properties of graphene oxide thin films

This work investigated the effect of Potassium Permanganate (KMnO₄) on graphene oxide (GO) properties, especially on electrical properties. The GO thin films were deposited on a glass substrate using drop casting technique and were analysed by using various type of spectroscopy (e.g. Scanning Electron Microscopy (SEM), Ultra- Violet Visible (UV–VIS), Fourier Transform Infrared (FTIR), X-Ray Diffraction (XRD), optical band gap, Raman Spectroscopy). Furthermore, the electrical experiments were carried out by using current–voltage (I-V) characteristic. The GO thin film with 4.5 g of KMnO₄ resulted in higher conductivity which is 3.11 × 10^?4 S/cm while GO with 2.5 g and 3.5 g of KMnO₄ achieve 2.47 × 10^?9 S/cm and 1.07 × 10^?7 S/cm, respectively. This further affects the morphological (SEM), optical (band gap, UV–Vis, FTIR, and Raman), and crystalline structural (XRD) properties of the GO thin films. The morphological, elemental, optical, and structural data confirmed that the properties of GO is affected by different amount of KMnO₄ oxidizing agent, which revealed that GO can potentially be implemented for electrical and electronic devices.     

Luminescent PMMA Films and PMMA@SiO2 Nanoparticles with Embedded Ln3+ Complexes for Highly Sensitive Optical Thermometers in the Physiological Temperature Range**

In recent years, luminescent materials doped with Ln³⁺ ions have attracted much attention for their application as optical thermometers based on both downshifting and upconversion processes. This study presents research done on the development of highly sensitive optical thermometers in the physiological temperature range based on poly(methyl methacrylate) (PMMA) films doped with two series of visible Ln³⁺ complexes (Ln³⁺=Tb³⁺, Eu³⁺, and Sm³⁺) and SiO₂ nanoparticles (NPs) coated with these PMMA films. The best performing PMMA film doped with Tb³⁺ and Eu³⁺ complexes was the PMMA[TbEuL₁tppo]1 film (L₁=4,4,4-trifluoro-1-phenyl-1,3-butadionate; tppo=triphenylphosphine oxide), which showed good temperature sensing of S_r=4.21 % K⁻¹ at 313 K, whereas for the PMMA films doped with Tb³⁺ and Sm³⁺ complexes the best performing was the PMMA[TbSmL₂tppo]3 film (L₂=4,4,4-trifluoro-1-(4-chlorophenyl)-1,3-butadionate), with S_r=3.64 % K⁻¹ at 313 K. Additionally, SiO₂ NPs coated with the best performing films from each of the series of PMMA films (Tb–Eu and Tb–Sm) and their temperature-sensing properties were studied in water, showing excellent performance in the physiological temperature range (PMMA[TbEuL₁tppo]1@SiO₂: S_r=3.84 % °C at 20 °C; PMMA[TbSmL₂tppo]3@SiO₂: S_r=3.27 % °C at 20 °C) and the toxicity of these nanoparticles on human cells was studied, showing that they were nontoxic.     

Structural,thermal and electrical properties of poly(methyl methacrylate)/CaCu3Ti4O12 composite sheets fabricated via melt mixing

Poly(methyl methacrylate) (PMMA) and CaCu₃Ti₄O₁₂ (CCTO) composites were fabricated via melt mixing followed by hot pressing technique. These were characterized using X-ray diffraction, thermo gravimetric, thermo mechanical, differential scanning calorimetry, fourier transform infrared (FTIR) and Impedance analyser for their structural, thermal and dielectric properties. Composites were found to have better thermal stability than that of pure PMMA. However, there was no significant difference in the glass transition (T _g ) temperature between the polymer and the composite. The appearance of additional vibrational frequencies in the range 400–600 cm^?1 in FTIR spectra indicated a possible interaction between PMMA and CCTO. The composite, with 38 vol% of CCTO (in PMMA), exhibited remarkably low dielectric loss at high frequencies and the low-frequency relaxation is attributed to the interfacial polarization/MWS effect. The origin of AC conductivity particularly in the high-frequency region was attributed to the electronic polarization.