利用还原性多糖合成银纳米粒子

利用还原性多糖为稳定剂、AgNO₃为前驱物, 通过一条绿色途径合成银纳米粒子, 并探讨了纳米粒子的形成机理. 对多糖高浓度时制得的复合物在空气与氮气气氛下进行了热处理, 分别得到了银的大孔海绵体与银纳米粒子/碳的复合材料. 对产物进行了X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见分光光度(UV-vis)以及BET吸附表征.     

银掺杂介孔氧化铝抗菌剂的一步合成与表征

以Al(NO_3)_3·9H_2O和AgNO_3为原料,采用水热法制备了介孔氧化铝纳米粒子(Mesoporous Al_2O_3NPs)和银掺杂介孔氧化铝纳米粒子(Mesoporous Ag/Al_2O_3NPs),通过X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、X射线荧光光谱(XRF)、能量分散X射线衍射(EDX)和低温N2吸附-脱附等手段对产物进行了表征,通过最低抑菌浓度和抑菌圈实验研究了材料的抗菌性能.XRD分析表明在介孔Ag/Al_2O_3NPs中Al_2O_3是唯一结晶相,Ag掺杂后,介孔Ag/Al_2O_3NPs晶格常数和半高峰宽增大,晶面间距[(111),(400)和(440)面]减小.FE-SEM形貌分析表明掺杂后的介孔Ag/Al_2O_3NPs颗粒直径减小而孔径增大.EDX和XRF分析表明介孔Ag/Al_2O_3NPs中O/Al摩尔比为1.5,与Al_2O_3NPs中O/Al摩尔比相同.综合XRD和XRF分析结果认为,Ag进入介孔Al_2O_3晶格间隙形成间隙固溶体.低温N2吸附-脱附分析表明掺杂后的介孔Ag/Al_2O_3NPs比表面积、孔体积和孔径增大.曝气抗菌实验结果表明介孔Ag/Al_2O_3NPs的抗菌机理是活性氧和金属银的协同作用.介孔Ag/Al_2O_3NPs对革兰氏阴性菌(大肠杆菌)和革兰氏阳性菌(金黄色葡萄球菌)具有明显的抗菌效果,对大肠杆菌和金黄色葡萄球菌的最低抑菌浓度(MIC)均为80μg/m L,抑菌圈直径分别为26 mm和24 mm.     

银纳米颗粒负载阶层多孔二氧化硅块体的制备及表征

以溶胶-凝胶伴随相分离法制备的阶层多孔二氧化硅作为载体,3-氨丙基三乙氧基硅烷(APTES)为改性剂,乙醇为还原剂,在阶层多孔二氧化硅固体骨架上进行银纳米颗粒均匀负载.利用扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)、汞压、N2吸附/脱附、X射线光电子能谱(XPS)等测试技术对银纳米颗粒负载阶层多孔二氧化硅进行了表征,探讨了APTES表面改性、乙醇还原机理以及银纳米颗粒负载块体的孔结构特征变化规律.结果表明:APTES表面改性将氨基接枝于阶层骨架上,氨基与银离子形成银氨离子,银氨离子经乙醇还原后将平均粒径约16 nm的银纳米颗粒成功负载于二氧化硅的大孔及介孔内部;负载后的阶层多孔块体的大孔骨架未受到破坏,但其比表面积由418 m2·g-1下降到254m2·g-1,两次还原负载能提高银纳米颗粒的负载量.     

儿茶素-银纳米复合材料的制备及其应用

探索了以植物活性成分儿茶素作为还原剂和保护剂一步水热法合成儿茶素-银纳米复合材料,并进一步测试了纳米复合材料的抑菌活性。 紫外可见吸收光谱(UV-Vis)和红外光谱(FTIR)测定证明制备得到了儿茶素包裹的银纳米粒子。 透射电子显微镜(TEM)和X射线衍射(XRD)结果显示银纳米粒子的平均粒径为22.7 nm,并具有面心立方晶体结构。 抑菌活性实验结果表明,儿茶素-银纳米复合粒子对大肠杆菌、金黄色葡萄球菌以及白色念球菌都有很强抑制作用,尤其对白色念球菌的抑制作用最强,其最低抑制浓度(MIC)和最低杀菌浓度(MBC)分别为19.63和39.26 μg/mL。 儿茶素-银纳米粒子强抑菌活性可归因于其表面银离子的持续释放,有望应用于长效抑菌制剂产品。     

无序介孔硅复合纳米结构的制备与慢活化行为

通过对SiO_2纳米粒子进行镁热还原及后处理,制备了多级无序Si介孔复合纳米结构MP-Si@SiO_x@C,此结构展现出容量非衰减缓升的电化学慢活化行为,可抵消循环容量常规衰减趋势,赋予负极优良的循环稳定性.通过X射线衍射(XRD)、透射电子显微镜(TEM)、场发射扫描电子显微镜(SEM)、N_2吸附-脱附测试和孔径分布模拟分析发现,Si介孔组织包含微-窄介孔(1~5 nm)、中介孔(5~20 nm)以及大介孔-宏孔(20~100 nm)三级孔道,分别源于原初级粒子内部孔道、粒子团聚堆垛与粒内酸蚀、团聚体再堆垛;此合成装配方法有效提升了Si材料的堆积密度,电池电极能获得较高的体积比容量和储能密度.     

纳米晶簇多级孔道L沸石的合成及其脱硫性能

采用晶化培育法制备了L沸石纳米晶簇,以其作为前驱体,并以3-三甲基甲硅烷基丙基十六烷基二甲基氯化铵(TPHAC)为模板剂,合成了微孔-介孔多级孔道L沸石(MeLTL沸石).通过X射线衍射(XRD)、氮气吸附-脱附、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、27Al固体魔角核磁(27AlMASNMR)和吡啶傅立叶变换红外(Py-FTIR)等方法对MeLTL沸石进行了表征.研究结果表明,MeLTL沸石是由L沸石纳米晶簇自组装形成的,并具有介孔孔道和L沸石的微孔结构以及适宜的酸量与酸强度,其比表面积和孔体积分别高达611m2.g-1和0.696cm.3g-1.将MeLTL沸石作为添加剂引入柴油加氢脱硫催化剂载体中,并与添加L沸石、Al-MCM-41和仅以γ-Al2O3为载体的催化剂进行比较,其脱硫性能为最佳,经加氢后的柴油硫含量仅为9.3μg.g-1,脱硫率达99.3%.     

有机官能化介孔硅基材料负载纳米金催化剂的制备及其催化性能

一步合成了桥键嵌入二硫醚官能化介孔硅基材料(PMO-SBA-15),利朋介孔硅基材料孔道内表面的二硫醚基团捕获纳米金(Au)粒子的作用,获得了负载型纳米Au催化剂(Au-PMO-SBA-15).小角X射线衍射和低温N2吸附-脱附的结果表明,PMO-SBA-15和Au-PMO-SBA-15均保持典型的介孔结构;高分辨透射电镜观察到纳米Au粒子在载体孔道内分散均匀,甲均粒径为(2.2±0.2)nm.以70%的叔丁基过氧化氧水溶液为氧化剂,考察了纳米Au催化剂Au-PMO-SBA-15在苯甲醇氧化反应中的催化性能.结果表明,当反应温度为353 K、反应时间为5 h时,苯甲醇的转化率为29.1%,苯甲醛的选择性为100%,且催化剂重复使用7次其催化活性和苯甲醛选择性基奉不变.     

磁性有序介孔炭的制备及药物吸附行为研究

采用纳米共铸法将磁性纳米粒子包埋到有序介孔炭的骨架中, 制成含有磁性纳米粒子的有序介孔炭(Fe/OMCs). 实验通过氮气吸附、扫描电镜、X射线衍射、磁性测试等手段对Fe/OMCs进行了系统的表征. 研究表明, Fe/OMCs基本保持了有序介孔结构, 磁性粒子在材料中以纳米α-Fe粒子的形式存在, 并且具有超顺磁特性. 盐酸四环素(TH)在Fe/OMCs上的吸附研究表明, Fe/OMCs的介孔表面积和介孔孔容是决定TH吸附量的关键因素. 脱附动力学研究表明, Fe/OMCs的孔尺寸是影响脱附速率的关键因素, 孔径越大, TH的脱附速率就越大.     

大孔-介孔Ag/PDA/MMS复合材料的制备及其催化性能

用双模板法制备了介孔纳米薄膜构筑的毫米级尺寸的大孔-介孔SiO₂(MMS),通过多巴胺(DA)在其孔道表面氧化自聚合成聚多巴胺(PDA),得到PDA修饰的MMS(PDA/MMS),再经PDA原位还原Ag+制得大孔-介孔Ag/PDA/MMS复合材料。应用扫描电镜、透射电镜、N2吸附-脱附、X射线光电子能谱、X射线衍射、UV-Vis、FT-IR和热重技术对所制得的材料进行表征。结果表明,MMS兼具纳米介孔材料和宏观尺寸大孔材料的优点。Ag/PDA/MMS在催化还原对硝基苯酚(4-NP)反应中展现出高催化活性,转化频率(TOF)达2.97 min^-1。这归因于其独特的结构：相互连通的大孔孔道大大降低了传质阻力,短孔道的介孔显著增加了活性位点的可达性,大的比表面积为反应物提供了大量的活性位点。而且,毫米级尺寸的Ag/PDA/MMS可以很容易从反应体系中分离出来,在5次循环后仍能将4-NP完全转化为对氨基苯酚(4-AP)。另外,Ag/PDA/MMS对亚甲基蓝(MB)的还原也有良好的催化效果。     

由沸石纳米粒子自组装制备具有高催化活性中心和水热稳定的新型介孔分子筛材料

 人们合成了一系列介孔分子筛材料，并发现它们在催化、吸附与分离以及化学组装制备先进材料和分子器件等方面具有很大的潜在应用价值．但是，介孔分子筛材料相对于微孔沸石分子筛存在着两个致命弱点：较低的水热稳定性和较不活泼的催化活性中心．这两个弱点大大地影响了介孔分子筛在催化反应中的广泛应用．本文系统地综述了最近几年利用沸石纳米粒子自组装制备具有高催化活性中心和水热稳定的介孔分子筛材料的研究进展．这包括利用硅铝沸石纳米粒子自组装制备具有强酸性和水热稳定的新型介孔硅铝分子筛材料，利用钛硅沸石纳米粒子自组装制备具有高催化氧化活性中心和水热稳定的新型钛硅介孔分子筛材料，以及利用含有不同杂原子的沸石纳米粒子自组装制备一系列水热稳定的新型介孔分子筛催化材料．     

Synthesis and structure of hydroxyisoxazolidines and derivatives of hydroxylamine and alkenals

The reactions of N-substituted hydroxylamines with alkenals serve as a method for the synthesis of the corresponding 2-substituted 3(5)-hydroxyisoxazolidines. The reaction pathway is determined by the nature of the substituent attached to the nitrogen atom. Ring-chain isomerism has been detected in these newly obtained compoundsTranslated from Khimiya Geterotsiklicheskikh Soedinenii, No. 9, pp. 1270–1276, September, 1987.     

Synthesis and characterization of triazenide and triazene complexes of ruthenium and osmium

Triazenide [M(eta2-1,3-ArNNNAr)P4]BPh4 [M = Ru, Os; Ar = Ph, p-tolyl; P = P(OMe)3, P(OEt)3, PPh(OEt)2] complexes were prepared by allowing triflate [M(kappa2-OTf)P4]OTf species to react first with 1,3-ArN=NN(H)Ar triazene and then with an excess of triethylamine. Alternatively, ruthenium triazenide [Ru(eta2-1,3-ArNNNAr)P4]BPh4 derivatives were obtained by reacting hydride [RuH(eta2-H2)P4]+ and RuH(kappa1-OTf)P4 compounds with 1,3-diaryltriazene. The complexes were characterized by spectroscopy and X-ray crystallography of the [Ru(eta2-1,3-PhNNNPh){P(OEt)3}4]BPh4 derivative. Hydride triazene [OsH(eta1-1,3-ArN=NN(H)Ar)P4]BPh4 [P = P(OEt)3, PPh(OEt)2; Ar = Ph, p-tolyl] and [RuH{eta1-1,3-p-tolyl-N=NN(H)-p-tolyl}{PPh(OEt)2}4]BPh4 derivatives were prepared by allowing kappa1-triflate MH(kappa1-OTf)P4 to react with 1,3-diaryltriazene. The [Os(kappa1-OTf){eta1-1,3-PhN=NN(H)Ph}{P(OEt)3}4]BPh4 intermediate was also obtained. Variable-temperature NMR studies were carried out using 15N-labeled triazene complexes prepared from the 1,3-Ph15N=N15N(H)Ph ligand. Osmium dihydrogen [OsH(eta2-H2)P4]BPh4 complexes [P = P(OEt)3, PPh(OEt)2] react with 1,3-ArN=NN(H)Ar triazene to give the hydride-diazene [OsH(ArN=NH)P4]BPh4 derivatives. The X-ray crystal structure determination of the [OsH(PhN=NH){PPh(OEt)2}4]BPh4 complex is reported. A reaction path to explain the formation of the diazene complexes is also reported.     

Mass and NMR spectra of haplophyllidine and perforine and of their derivatives

Conclusions The mass and NMR spectra of haplophyllidine, perforine, and their derivatives have been studied. The influence of the open and cyclic forms of the molecular ion on the nature of the fragmentation has been discussed. The main routes of fragmentation of the compounds considered are due to the presence of substituents at C₈ and C₄.Khimiya Prirodnykh Soedinenii, Vol. 5, No. 4, pp. 273–279, 1969     

Crystal and molecular structure of aroyl- and acetylhydrazones of acet- and benzaldehydes

Aroyl- and acetylhydrazones of acet- (I) and benzaldehydes (IV) and benzoylhydrazones of acet- (II) and benzaldehydes (III) were studied by x-ray structural and quantum-chemical methods in order to establish their structures. Compund (I) was the EEZ structure in the crystal. Calculations and spectral data showed that the EEE form occurs in nonpolar solvents and in the gas phase. According to crystallographic data molecules (I)–(IV) are the E-isomers (relative to the N-N bond) and the hydrazone fragments are planar. Intermolecular N-H...O H-bonds from in the crystals. The data obtained suggest that the majority of acylhydrazones are conformationally rigid on dissolution although exceptions do occur. Apparently the reasons for the difference of acetyl- and benzoylhydrazones in electrocarboxylation reactions are electronic and not steric factors.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 1, pp. 75–81, January, 1991.     

Investigation of adhesion and mobility of polyurethane and epoxy-rubber glues and adhesives

The values of activation parameters in uncured and cured epoxy resins, rubbers, and blends thereof are investigated. The dependences of activation energy and adhesion strength of epoxy-rubber compositions on rubber content are determined. The correlation of adhesion and activation energy values for polyurethane rubber and epoxy-rubber compositions is shown.     

Preparation and characterization of diarylphosphazene and diarylphosphinohydrazide complexes of titanium, tungsten and ruthenium and phosphorylketimido complexes of rhenium

Reaction of the proligand Ph2PN(SiMe3)2 (L1) with WCl6 gives the oligomeric phosphazene complex [WCl4(NPPh2)]n, 1 and subsequent reaction with PMe2Ph or NBu4Cl gives [WCl4(NPPh2)(PMe2Ph)] (2) or [WCl5(NPPh2)][NBu4] (3), respectively. DF calculations on [WCl5(NPPh2)][NBu4] show a W=N double bond (1.756 A) and a P-N bond distance of 1.701 A, which combined with the geometry about the P atom suggests, there is no P-N multiple bonding. Reaction of L1 with [ReOX3(PPh3)2] in MeCN (X = Cl or Br) gives [ReX2(NC(CH3)P(O)Ph2)(MeCN)(PPh3)](X = Cl, 4, X = Br, 5) which contains the new phosphorylketimido ligand. It is bound to the rhenium centre with a virtually linear Re-N-C arrangement (Re-N-C angle = 176.6 degrees, when X = Cl) and there is multiple bonding between Re and N (Re-N = 1.809(7) A when X = Cl). The proligand Ph2PNHNMe2(L2H) reacts with [(C5H5)TiCl3] to give [(C5H5)TiCl2(Me2NNPPh2)] (6). An X-ray crystal structure of the complex shows the ligand (L2) is bound by both nitrogen atoms. Reaction of the proligands Ph2PNHNR2[R2 = Me2 (L2H), -(CH2CH2)2NCH3 (L3H), (CH2CH2)2CH2 (L4H)] with [{RuCl(mu-Cl)(eta6-p-MeC6H4iPr)}2] gave [RuCl2(eta6-p-MeC6H4iPr)L] {L = L2H (7), L3H (8), L4H (9)}. The X-ray crystal structures of 7-9 confirmed that the phosphinohydrazine ligand is neutral and bound via the phosphorus only. Reaction of complexes 7-9 with AgBF4 resulted in chloride ion abstraction and the formation of the cationic species [RuCl(6-p-MeC6H4iPr)(L)]+ BF4- {(L = L2H (10), L3H (11), L4H (12)}. Finally, reaction of complex 6 with [{RuCl(mu-Cl)(eta6-p-MeC6H4iPr)}2] gave the binuclear species [(eta6-p-MeC6H4iPr)Cl2Ru(mu2,eta3-Ph2PNNMe2)TiCl2(C5H5)], 13.     

The chemical transport of molybdenum and tungsten and of their dioxides and sulfides

Experiments have been made and an extensive thermodynamic discussion has taken place concerning the chemical transport of Mo, W, MoO₂, WO₂, MoS₂ and WS₂ in the presence of iodine. Efforts have been made to find the species via which Mo and W can migrate within the gas phase.Results: In each case the transport proceeds via the oxide iodides MoO₂J₂ and WO₂J₂ respectively, as already known for the dioxides. Thus the chemical transport of Mo, W, MoS₂ and WS₂ needs not only J₂ but also H₂O, usually liberated from the wall of the quartz ampoule.By means of J₂ + H₂O, the metals can be transported into the high temperature region of the ampoule (e.g., 1050 → 1150°C), whereas the transport of the sulfides proceeds in the opposite direction (e.g., 900 → 700°C).For the sulfide-transport the influence of the ratio of the transport agents $\text{J}{}_2\text{H}{}_2\text{O}$ has been discussed.The water content of the quartz glass out of which the ampoules are made is an important source for water, influencing the reactions.The addition of graphite which considerably lowers the H₂O partial pressure prevents any transport of the metals or the sulfides, which proves that the use of J₂ alone as a transport agent is insufficient in these cases.The gaseous iodides MoJ_x and WJ_z are without any importance under the experimental conditions used for the transport of the metals, their dioxides and sulfides.The partial pressures of MoO₂(OH)₂ and WO₂(OH)₂ under the experimental conditions chosen may usually be neglected. But in the system $\text{MoO}{}_2\text{H}{}_2\text{O}$ the transport via MoO₂(OH)₂ (1000 → 800°C) has been observed.The synthesis of MoO₂ and WO₂, starting with the elements or with powder of metal and trioxide is promoted by the addition of J₂. The reaction steps involved are discussed.     

Simultaneous spectrophotometric determination of molybdenum and selenium,and of molybdenum and tellurium

A method is reported for the extraction of molybdenum-phenylfluorone by chloroform. The extraction is complete whether perchlorate ions are present or not but the extractions in the presence of perchlorate ions gave a somewhat more sensitive procedure for the spectrophotometric determination of molybdenum in the solvent phase as the molybdenum-phenylfluorone complex.A procedure is reported for the simultaneous determination of molybdenum and selenium, and molybdenum and tellurium. The method involves first the formation and solvent extraction of the molybdenum-phenylfluorone complex by chloroform in the presence of perchlorate ions, followed by determination of selenium in the remaining aqueous phase as selenium-diethyldithiocarbamate complex after solvent extraction with 2-ethyl-1-hexanol in the presence of perchlorate ions. A similar procedure is reported for the simultaneous determination of molybdenum and tellurium except that in the determination of molybdenum, the phenylfluorone complex is extracted by chloroform in the absence of perchlorate ions. Tellurium is determined in the remaining aqueous phase as tellurium-diethyldithiocarbamate complex after solvent extraction by 2-ethyl-1-hexanol solvent extraction in the presence of perchlorate ions.