Catalytic carbon monoxide oxidation over CuO/CeO2 composite catalysts

Summary CeO₂ nanoparticles were prepared by thermal decomposition of cerous nitrate and then used as supports for CuO/CeO₂ catalysts prepared via the impregnation method. The samples were characterized by XRD, HRTEM, H₂-TPR and XPS. The catalytic properties of the catalysts for low-temperature CO oxidation were studied by using a microreactor-GC system.     

Preparation,Characterization, and Catalytic Behavior of Nanostructured Mesoporous CuO/ZrO2 Catalysts for Low-Temperature CO Oxidation

High-surface area mesoporous 20 mol% CuO/ZrO₂ catalyst was prepared by a surfactant-assisted method of nanocrystalline particle assembly, and characterized by x-ray powder diffraction (XRD), N₂ adsorption, transmission electron microscopy (TEM), H₂-TPR, TG-DTA, and x-ray photoelectron spectra (XPS) techniques. The catalytic properties of the CuO/ZrO₂ nanocatalysts calcined at different temperature were evaluated by low-temperature carbon monoxide oxidation using a CATLAB system. The results showed that these mesoporous nanostructured CuO/ZrO₂ catalysts were very active for low-temperature CO oxidation and the CuO/ZrO₂ catalyst calcined at 400°C exhibited the highest catalytic activity.     

焙烧与预处理条件对 Co3O4 催化氧化 CO 性能的影响

采用沉淀法制备了 Co₃O₄, 考察了焙烧和预处理条件对其结构、低温催化氧化 CO 性能的影响. 热重分析表明, 未经焙烧的样品以 Co(OH)₂CO₃ 的形式存在, 150~400 ^oC 空气气氛中焙烧后, 样品以立方相 Co₃O₄ 的形式存在. N2 吸附-脱附法、X 射线衍射、透射电镜及活性测试结果表明, 以纳米颗粒物存在的 Co₃O₄ 的比表面积、颗粒尺寸、催化氧化 CO 活性与焙烧温度密切相关. 正电子湮没寿命谱、O₂-程序升温脱附与定温条件下 CO 氧化测试结果表明, 合适温度 (150~250 ^oC) 下 N₂ 预处理有利于 Co₃O₄ 表面氧空穴团的形成, 它在吸附活化分子氧以及 CO 催化氧化反应中起到关键作用. 同时讨论了预处理作用下Co₃O₄表面氧空穴的再构机制.     

制备方法对CuO/CeO_2-ZrO_2催化CO低温氧化活性的影响

采用微波加热分解法(一步法)和微波加热处理共沉淀+浸渍法(两步法)制备了CuO/CeO2-ZrO2催化剂,并对其进行了X射线衍射、低温氮气吸附/脱附和程序升温还原等表征,采用色谱流动法考察了催化剂的催化CO低温氧化性能.结果表明,一步法比两步法更有利于使催化剂表面CuO高度分散,CuO与CeO2-ZrO2间的相互作用更强,CuO更容易被还原,从而具有更高的催化CO氧化活性.与CeO2-ZrO2有相互作用的高分散和小颗粒CuO有利于催化剂活性的提高,与CeO2-ZrO2无相互作用的大颗粒CuO对催化剂的活性有抑制作用.     

Pt/TiO2催化剂上CO氧化反应动力学研究

利用沉积沉淀法制备了Pt/TiO₂催化剂, 将其在不同温度下焙烧, 以得到不同颗粒尺寸的Pt. 并将这些样品用于CO催化氧化反应以及反应动力学研究. 结果表明: 焙烧温度对催化剂有明显影响, Pt 颗粒尺寸随着焙烧温度的升高而增加; 与此同时, CO催化活性随焙烧温度的升高呈先增加后降低的趋势, 其中, 400℃焙烧的样品表现出最高的催化活性. 反应动力学结果表明, 催化剂上CO氧化反应表观速率方程为r=5.4×10^-7p_CO^0.17p_O2^0.36,说明在该催化剂上CO氧化遵循Langmuir-Hinshelwood机理. 同时, 对催化剂进行了CO化学吸附红外光谱和O₂化学吸附表征. 结果表明, 随着焙烧温度的升高, 催化剂上CO和O₂吸附量均呈现先升高后降低的趋势, 这与反应结果和反应动力学方程一致, 说明反应受到催化剂表面上CO和O₂吸附浓度的影响. 而在400℃焙烧的催化剂上, CO和O₂吸附量均最高, 因此其反应活性也最好. 这可能是焙烧过程影响了Pt 和TiO₂之间的相互作用引起的.     

Influence of ceria preparation method on the performance of CuO/CeO2 catalysts

Ceria were prepared by various processes. The prepared samples and commercial ceria were used as supports to prepare the CuO/CeO₂ catalysts via an impregnation method. The samples were characterized by using TEM, XRD, H₂-TPR, and their catalytic activities in low-temperature CO oxidation were also investigated.     

Enhanced Activity of CuCeO Catalysts for CO Oxidation: Influence of Cu2O and the Dispersion of Cu2O,CuO, and CeO2

CuCeO catalysts prepared by a hydrothermal method with subsequent calcination are tested for the catalytic oxidation of CO. This synthesis method leads to a homogeneous dispersion of Cu₂O, CuO, and CeO₂ in the catalysts. The composition of the catalysts is determined by the molar ratio of the metals, the hydrothermal process, and calcination temperature and influences the catalytic performance. The catalyst containing Cu₂O exhibits high catalytic activity with almost 100 % CO conversion at 105 °C and shows excellent stability with the conversion ratio not decreasing after four months of storage.     

焙烧温度对柴油车氧化催化剂Pt-Pd-（x）ZrO2/Ce0.3Zr0.7O2-Al2O3性能的影响

制备了氧化铝、铈锆固溶体复合氧化物负载铂、钯的双金属催化剂Pt-Pd/ Ce0.3Zr0.7O2-Al2O3,并添加3% ZrO2助剂改性,用于柴油车尾气中CO、HC和NO的催化氧化,其中贵金属负载量仅为0.68 wt%。考察了制备过程中焙烧温度对催化剂性能的影响。催化剂活性评价结果表明,与未添加ZrO2的催化剂比较。添加ZrO2明显提高了催化剂的低温氧化活性,而且焙烧温度对催化剂的氧化性能有较大影响。焙烧温度为800 ?C时,CO和C3H6的起燃温度最低,分别为168、189 ?C,焙烧温度为700 ?C时,NO转化为NO2的转化率最高,最大转化率为36%,具有较好的热稳定性。通过XRD、N2吸附-脱附、CO化学吸附、XPS、H2-TPR等表征手段考察了催化剂物理化学性质随焙烧温度的变化情况,并分析了与催化剂活性之间的关系,得到贵金属分散度、表面化学吸附氧含量、催化剂的还原性质对氧化性能有重要影响,发挥协同作用。进而可以通过优化焙烧温度提升柴油车氧化催化剂性能,对提高工业应用柴油车尾气后处理系统的净化效率有重要意义。     

Surface and catalytic properties of Cu/Zn mixed oxide catalysts

Copper catalysts supported on zinc oxide, with different loading (1–20 wt.% CuO), were prepared by impregnation of the basic zinc carbonate with a water solution of copper nitrate. The impregnated samples were dried at 120°C and calcined at 400–700°C. The surface and catalytic properties of CuO loaded on ZnO were determined by N₂ adsorption measurements conducted at −196°C and CO oxidation by O₂ at 150–300°C, respectively. The results obtained revealed that the surface and catalytic properties of different solids were dependent upon CuO content and calcination temperature. The specific surface areas of various adsorbents decreased monotonically as a function of both calcination temperature and extent of loading. However, the activation energy of sintering, ΔE_S, was found to increase by increasing the amount of CuO present. On the other hand, the CO oxidation activity on various catalysts was found to increase progressively by increasing the calcination temperature from 400 to 500°C, then decreased by increasing the temperature from 500 to 700°C. The augmentation of CuO content from 1 to 5 wt.% resulted in an increase in the CO oxidation activity, which decreased by increasing the extent of loading above this limit.     

CO oxidation over Co3O4/SiO2 catalysts: Effects of porous structure of silica and catalyst calcination temperature

The catalytic performances of Co3O4/SiO2 catalysts prepared by incipient wetness impregnation for CO oxidation were investigated using three kinds of silica as carriers with different pore sizes of 7.7, 14.0 and 27.0 nm. The effects of calcination temperature on the catalyst surface and micro structure properties as well as catalytic performance for the oxidation of carbon monoxide were also studied. All catalysts were characterized by N2 adsorption-desorption, XRD, XPS, FTIR, H2-TPR and O2-TPD. It was found that the properties and crystal size of cobalt-containing species strongly depended on the pore size of silica carrier. While the silica pore size increased from 7.7 to 27.0 nm, the Co3O4 crystal size increased from 8.5 to 13.5 nm. Moreover, it was demonstrated that if the spinel crystal structure of Co3O4 was obtained at a calcination temperature as low as 150 ℃, the catalyst sample would have a high Co3O4 surface dispersion and a increase of surface active species, and thus exhibit a high activity for the oxidation of carbon monoxide.     

超声改性的CuO/Al2O3-MgO催化剂结构 及其超低浓度甲烷催化燃烧性能

采用普通浸渍和超声改性的方法分别制备了CuO/Al₂O₃-MgO催化剂,用于超低浓度甲烷的催化燃烧,并利用SEM、XRD、XPS、H₂-TPR等技术对催化剂进行表征,研究了超声改性作用对催化剂的结构和性能的影响.结果表明,与普通浸渍法制备的催化剂相比,在超声改性的CuO/Al₂O₃-MgO催化剂上,甲烷的转化率得到提高,燃烧特征温度降低.随着超声时间的延长和超声功率的增加,催化剂的催化活性均呈现先增大后减小的趋势;催化剂制备的最佳超声工况为功率150 W、时间20 min.超声改性可使催化剂的比表面积和孔容积增大,表面催化活性较高的Cu⁺浓度增加,活性组分CuO由晶相向非晶相转变、分散度增大,晶粒粒径变小、分布更均匀;这使得甲烷催化燃烧的表观活化能下降、催化剂活性得到增强.     

CuO-CeO_2的固相反应法制备及其催化CO低温氧化性能

采用固相化学反应法制备了一系列CuO-CeO_2催化剂,并用X-射线衍射(XRD)、程序升温还原(H_2-TPR)和氮吸附等技术对样品进行了表征,利用微反-色谱装置考察了其催化CO低温氧化反应的活性,研究了CuO含量和催化剂焙烧温度对CuO-CeO_2催化活性的影响。结果表明,随着CuO含量的增加,CuO-CeO_2的催化活性提高,至不小于15%时达到稳定;随焙烧温度的升高,CuO-CeO_2的催化活性先提高,至650℃时达到最大,之后又降低。CuO-CeO_2的催化活性与其CuO的还原性之间有较好的对应关系。     

Selective oxidation of CO in the presence of hydrogen on CuO/CeO<Subscript>2</Subscript> catalysts modified with Fe and Ni oxides

The selective oxidation of CO in the presence of hydrogen on CuO/CeO₂ systems containing Fe and Ni oxides as promoters was studied. The catalysts containing 1–5 wt % CuO and 1–2.5 wt % Fe₂O₃ supported on CeO₂ and the CuO/CeO₂ systems containing 1–2.5 wt % NiO were synthesized, and their catalytic activity as a function of temperature was determined. It was found that the additives of Fe and Ni oxides increased the activity of the CuO/CeO₂ catalysts with a low concentration of CuO. In this case, the conversion of CO at 150°C approached 100%. At the same time, these additives had no effect on the activity of the CuO/CeO₂ systems at a CuO concentration of 5 wt % or higher, which exhibited an initially high activity in the above temperature region. The forms of CO adsorption and the amounts of active sites for CO adsorption and oxidation were studied using temperature-programmed desorption. It was found that the introduction of Fe and Ni additives in a certain preparation procedure facilitated the formation of an additional amount of active centers associated with CuO. Data on the temperature-programmed reduction of samples (the amount of absorbed hydrogen and the maximum temperature of hydrogen absorption) suggested the interaction of all catalyst components, and the magnitude of this interaction depended on the sample preparation procedure. With the use of Mössbauer spectroscopy, it was found that the procedure of iron oxide introduction into the CuO/CeO₂ system was responsible for the electron-ion interactions of catalyst components and the reaction mixture.     

Effect of the calcination temperature on the properties of Fe2O3/SiO2 catalysts for oxidation of hydrogen sulfide

The effect of the calcination temperature on the properties of supported iron oxide catalysts for hydrogen sulfide oxidation prepared by impregnation of silica with iron(III) nitrate has been studied. An increase in the calcination temperature was found to diminish the catalytic activity of the Fe₂O₃/SiO₂ catalysts in hydrogen sulfide oxidation. This behavior can be explained by the agglomeration of iron oxide particles and by a decrease in the surface concentration of active sites. It has been shown that an increase in the calcination temperature makes the catalyst more stable towards the sulfidation of the active component (Fe₂O₃) to the iron disulfide phase.     

CuO Catalysts Supported on Porous TiO2 Microspheres for Low-Temperature CO Oxidation

The porous TiO₂ microspheres were prepared by the reversed-phase suspension polymerization and sol-gel method using reversed-phase suspension droplets as the templates. The CO oxidation catalytic properties of the CuO/TiO₂ catalysts prepared by hydrothermal method and impregnation method were extensively investigated. The structure of CuO/TiO₂ catalysts was determined by TG-DTA, XRD, TEM, and XPS. The results indicated that the redox capacity of CuO/TiO₂ was greatly depended on the aqueous solution concentration of Cu(NO₃)₂ used in the preparation of CuO/TiO₂ and the calcination temperature of the CuO/TiO₂ catalysts.     

Preparation and catalytic oxidation performance andOF Pr2-xSrxCoO4+λwithK2NiF4structure

Summary A series of Pr_2-xSr_xCoO_4+λmixed oxides were prepared and used successfully for oxidation of CO and C₃H₈. The results show that Pr_2-xSr_xCoO_4+λdisplay K₂NiF₄-type structure and their catalytic activities are closely correlated with the concentration of Co³⁺, mobile lattice oxygen and oxygen vacancy.</o:p>     

Production of hydrogen by oxidative steam reforming of methanol over Cu/SiO2 catalysts

Selective production of hydrogen by oxidative steam reforming of methanol (OSRM) was studied over Cu/SiO₂ catalyst using fixed bed flow reactor. Textural and structural properties of the catalyst were analyzed by various instrumental methods. TPR analysis illustrates that the reduction temperature peak was observed between 510?K and 532?K at various copper loadings and calcination temperatures and the peaks shifted to higher temperature with increasing copper loading and calcination temperature. The XRD and XPS analysis demonstrates that the copper existed in different oxidation states at different conditions: Cu₂O, Cu⁰, CuO and Cu(OH)₂ in uncalcined sample; CuO in calcined sample: Cu₂O and metallic Cu after reduction at 600?K and Cu⁰ and CuO after catalytic test. TEM analysis reveals that at various copper loadings, the copper particle size is in the range between 3.0?nm and 3.8?nm. The Cu particle size after catalytic test increased from 3.6 to 4.8?nm, which is due to the formation of oxides of copper as evidenced from XRD and XPS analysis. The catalytic performance at various Cu loadings shows that with increasing Cu loading from 4.7 to 17.3?wt%, the activity increases and thereafter it decreases. Effect of calcination shows that the sample calcined at 673?K exhibited high activity. The O₂/CH₃OH and H₂O/CH₃OH molar ratios play important role in reaction rate and product distribution. The optimum molar ratios of O₂/CH₃OH and H₂O/CH₃OH are 0.25 and 0.1, respectively. When the reaction temperature varied from 473 to 548?K, the methanol conversion and H₂ production rate are in the range of 21.9–97.5% and 1.2–300.9?mmol?kg^?1?s^?1, respectively. The CO selectivity is negligible at these temperatures. Under the optimum conditions (17.3?wt%, Cu/SiO₂; calcination temperature 673?K; 0.25 O₂/CH₃OH molar ratio, 0.5 H₂O/CH₃OH molar ratio and reaction temperature 548?K), the maximum hydrogen yield obtained was 2.45?mol of hydrogen per mole of methanol. The time on stream stability test showed that the Cu/SiO₂ catalyst is quite stable for 48?h.     

氧化铈气凝胶担载氧化铜催化剂上的一氧化碳氧化

 以一氧化碳氧化为探针反应,考察了氧化铈气凝胶担载氧化铜催化剂的催化活性,研究了催化剂中氧化铜的含量、载体及催化剂的焙烧温度对催化剂活性的影响．结果表明,氧化铈气凝胶担载的氧化铜催化剂对一氧化碳氧化反应呈现出高催化活性,适当温度下焙烧载体及催化剂有利于提高催化剂的催化活性;随着催化剂中氧化铜含量的增加,一氧化碳完全转化的温度降低,但当w（CuO）＞12％时,过量的氧化铜以体相形式而不是以高分散形式存在,对催化剂活性的影响很小．     

Effect of Calcination Temperature on Surface Oxygen Vacancies and Catalytic Performance Towards CO Oxidation of Co3O4 Nanoparticles Supported on SiO2

Co₃O₄/SiO₂ catalysts for CO oxidation were prepared by conventional incipient wetness impregnation followed by calcination at various temperatures. Their structures were char-acterized with X-ray diffraction (XRD), laser Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction (TPR) and X-ray absorption fine structure (XAFS) spectroscopy. Both XRD and Raman spectroscopy only detect the ex-istence of Co₃O₄ crystallites in all catalysts. However, XPS results indicate that excess Co²⁺ ions are present on the surface of Co₃O₄ in Co₃O₄(200)/SiO₂ as compared with bulk Co₃O₄. Meanwhile, TPR results suggest the presence of surface oxygen vacancies on Co₃O₄ in Co₃O₄(200)/SiO₂, and XAFS results demonstrate that Co₃O₄ in Co₃O₄(200)/SiO₂ con-tains excess Co²⁺. Increasing calcination temperature results in oxidation of excess Co²⁺ and the decrease of the concentration of surface oxygen vacancies, consequently the for-mation of stoichiometric Co₃O₄ on supported catalysts. Among all Co₃O₄/SiO₂ catalysts,Co₃O₄(200)/SiO₂ exhibits the best catalytic performance towards CO oxidation, demon-strating that excess Co²⁺ and surface oxygen vacancies can enhance the catalytic activity of Co₃O₄ towards CO oxidation. These results nicely demonstrate the effect of calcination temperature on the structure and catalytic performance towards CO oxidation of silica-supported Co₃O₄ catalysts and highlight the important role of surface oxygen vacancies on Co₃O₄.     

Supported CuO/Ce1−x Zr x O2 catalysts for the preferential oxidation of CO in H2-rich gases

The catalytic properties of CuO supported on ceria or ceria-zirconia mixed oxides have been investigated in the preferential oxidation of CO in H₂-rich gases. CuO/CeO₂ shows very high activity towards the oxidation of CO with a light-off temperature of about 70°C. This catalyst is very selective for the oxidation of CO rather than of H₂ in the low temperature region (70–120°C), while at higher temperatures, the oxidation of hydrogen begins, causing of a maximum of CO conversion to arise with increasing temperature. Published in Russian in Kinetika i Kataliz, 2006, Vol. 47, No. 5, pp. 779–787. This article was submitted by the authors in English.