Comparison of changes in cellulose ultrastructure during different pretreatments of poplar

One commonly cited factor that contributes to the recalcitrance of biomass is cellulose crystallinity. The present study aims to establish the effect of several pretreatment technologies on cellulose crystallinity, crystalline allomorph distribution, and cellulose ultrastructure. The observed changes in the cellulose ultrastructure of poplar were also related to changes in enzymatic hydrolysis, a measure of biomass recalcitrance. Hot-water, organo-solv, lime, lime-oxidant, dilute acid, and dilute acid-oxidant pretreatments were compared in terms of changes in enzymatic sugar release and then changes in cellulose ultrastructure measured by ¹³C cross polarization magic angle spinning nuclear magnetic resonance and wide-angle X-ray diffraction. Pretreatment severity and relative chemical depolymerization/degradation were assessed through compositional analysis and high-performance anion-exchange chromatography with pulsed amperometric detection. Results showed minimal cellulose ultrastructural changes occurred due to lime and lime-oxidant pretreatments, which at short residence time displayed relatively high enzymatic glucose yield. Hot water pretreatment moderately changed cellulose crystallinity and crystalline allomorph distribution, yet produced the lowest enzymatic glucose yield. Dilute acid and dilute acid-oxidant pretreatments resulted in the largest increase in cellulose crystallinity, para-crystalline, and cellulose-I_β allomorph content as well as the largest increase in cellulose microfibril or crystallite size. Perhaps related, compositional analysis and Klason lignin contents for samples that underwent dilute acid and dilute acid-oxidant pretreatments indicated the most significant polysaccharide depolymerization/degradation also ensued. Organo-solv pretreatment generated the highest glucose yield, which was accompanied by the most significant increase in cellulose microfibril or crystallite size and decrease in relatively lignin contents. Hot-water, dilute acid, dilute acid-oxidant, and organo-solv pretreatments all showed evidence of cellulose microfibril coalescence.     

Structural coarsening of aspen wood by hydrothermal pretreatment monitored by small- and wide-angle scattering of X-rays and neutrons on oriented specimens

Structural changes across multiple length scales associated with hydrothermal pretreatments of biomass were investigated by using small- and wide-angle X-ray and neutron scattering on oriented specimens. Isotropic and anisotropic scattering components were numerically separated and then interpreted as contributions from matrix and cellulose components, respectively. Equatorial diffraction peaks present in the isotropic component became sharper after hydrothermal treatments or ammonia treatment. Before pretreatment the wet cell wall was found to be homogeneous in the 10–100 nm range and scattering below Q = 0.5 (nm^?1) was dominated by surface scattering from the lumen. After pretreatment with acid or steam at 160 or 180 °C, density fluctuation developed in the cell wall at length scales above 10 nm, most likely due to lateral coalescence of microfibrils that partially co-crystallize to give larger apparent crystal sizes. A density fluctuation up to about 100 nm appeared in the isotropic component after acid and steam pretreatments due to morphological changes in the hemicellulose and lignin matrix.     

Evaluation and Characterization of Forage Sorghum as Feedstock for Fermentable Sugar Production

Sorghum is a tropical grass grown primarily in semiarid and drier parts of the world, especially areas too dry for corn. Sorghum production also leaves about 58 million tons of by-products composed mainly of cellulose, hemicellulose, and lignin. The low lignin content of some forage sorghums such as brown midrib makes them more digestible for ethanol production. Successful use of biomass for biofuel production depends on not only pretreatment methods and efficient processing conditions but also physical and chemical properties of the biomass. In this study, four varieties of forage sorghum (stems and leaves) were characterized and evaluated as feedstock for fermentable sugar production. Fourier transform infrared spectroscopy and X-ray diffraction were used to determine changes in structure and chemical composition of forage sorghum before and after pretreatment and the enzymatic hydrolysis process. Forage sorghums with a low syringyl/guaiacyl ratio in their lignin structure were easy to hydrolyze after pretreatment despite the initial lignin content. Enzymatic hydrolysis was also more effective for forage sorghums with a low crystallinity index and easily transformed crystalline cellulose to amorphous cellulose, despite initial cellulose content. Up to 72% hexose yield and 94% pentose yield were obtained using modified steam explosion with 2% sulfuric acid at 140 °C for 30 min and enzymatic hydrolysis with cellulase (15 filter per unit (FPU)/g cellulose) and β-glucosidase (50 cellobiose units (CBU)/g cellulose).     

Understanding factors that limit enzymatic hydrolysis of biomass

Spectroscopic characterization of both untreated and treated material is being performed in order to determine changes in the biomass and the effects of pretreatment on crystallinity, lignin content, selected chemical bonds, and depolymerization of hemicellulose and lignin. The methods used are X-ray diffraction for determination of cellulose crystallinity (CrI); diffusive reflectance infrared (DRIFT) for changes in C-C and C-O bonds; and fluorescence to determine lignin content. Changes in spectral characteristics and crystallinity are statistically correlated with enzymatic hydrolysis results to identify and better understand the fundamental features of biomass that govern its enzymatic conversion to monomeric sugars. Models of the hydrolysis initial rate and 72 h extent of conversion were developed and evaluated. Results show that the hydrolysis initial rate is most influenced by the cellulose crystallinity, while lignin content most influences the extent of hydrolysis at 72 h. However, it should be noted that in this study only crystallinity, lignin, and selected chemical bonds were used as inputs to the models. The incorporation of additional parameters that affect the hydrolysis, like pore volume and size and surface area accessibility, would improve the predictive capability of the models.     

SANS analysis of the microstructural evolution during the aging of pyrolysis oils from biomass

In this paper, we report for the first time a microstructural characterization of pyrolysis oils obtained from biomass. Bio crude oils (BCOs) are good candidates as substitutes for mineral oils as fuels. By using small-angle neutron scattering (SANS), we show that BCOs are nanostructured fluids constituted by a complex continuous phase and nanoparticles mainly formed by the association of units of pyrolytic lignins. The aggregation of these units during the time produces branched structures with fractal dimension D(f) between 1.4 and 1.5, which are responsible for BCO aging. SANS results fully support the recently formulated thermal ejection theory, accounting for the mechanism of formation of the lignin fraction in oils obtained from fast pyrolysis of biomass.     

Pretreatment Methods for Bioethanol Production

Lignocellulosic biomass, such as wood, grass, agricultural, and forest residues, are potential resources for the production of bioethanol. The current biochemical process of converting biomass to bioethanol typically consists of three main steps: pretreatment, enzymatic hydrolysis, and fermentation. For this process, pretreatment is probably the most crucial step since it has a large impact on the efficiency of the overall bioconversion. The aim of pretreatment is to disrupt recalcitrant structures of cellulosic biomass to make cellulose more accessible to the enzymes that convert carbohydrate polymers into fermentable sugars. This paper reviews several leading acidic, neutral, and alkaline pretreatments technologies. Different pretreatment methods, including dilute acid pretreatment (DAP), steam explosion pretreatment (SEP), organosolv, liquid hot water (LHW), ammonia fiber expansion (AFEX), soaking in aqueous ammonia (SAA), sodium hydroxide/lime pretreatments, and ozonolysis are intensively introduced and discussed. In this minireview, the key points are focused on the structural changes primarily in cellulose, hemicellulose, and lignin during the above leading pretreatment technologies.     

Effect of ionic liquid treatment on the structures of lignins in solutions: molecular subunits released from lignin

The solution structures of three types of isolated lignin-organosolv (OS), Kraft (K), and low sulfonate (LS)-before and after treatment with 1-ethyl-3-methylimidazolium acetate were studied using small-angle neutron scattering (SANS) and dynamic light scattering (DLS) over a concentration range of 0.3-2.4 wt %. The results indicate that each of these lignins is comprised of aggregates of well-defined basal subunits, the shapes and sizes of which, in D(2)O and DMSO-d(6), are revealed using these techniques. LS lignin contains a substantial amount of nanometer-scale individual subunits. In aqueous solution these subunits have a well-defined elongated shape described well by ellipsoidal and cylindrical models. At low concentration the subunits are highly expanded in alkaline solution, and the effect is screened with increasing concentration. OS lignin dissolved in DMSO was found to consist of a narrow distribution of aggregates with average radius 200 ± 30 nm. K lignin in DMSO consists of aggregates with a very broad size distribution. After ionic liquid (IL) treatment, LS lignin subunits in alkaline solution maintained the elongated shape but were reduced in size. IL treatment of OS and K lignins led to the release of nanometer-scale subunits with well-defined size and shape.     

Effects of SPORL and Dilute Acid Pretreatment on Substrate Morphology, Cell Physical and Chemical Wall Structures, and Subsequent Enzymatic Hydrolysis of Lodgepole Pine

The effects of pretreatment by dilute acid and sulfite pretreatment to overcome recalcitrance of lignocellulose (SPORL) on substrate morphology, cell wall physical and chemical structures, along with the subsequent enzymatic hydrolysis of lodgepole pine substrate were investigated. FE-SEM and TEM images of substrate structural morphological changes showed that SPORL pretreatment resulted in fiber separation, where SPORL high pH (4.2) pretreatment exhibited better fiber separation than SPORL low pH (1.9) pretreatment. Dilute acid pretreatment produced very poor fiber separation, consisting mostly of fiber bundles. The removal of almost all hemicelluloses in the dilute acid pretreated substrate did not overcome recalcitrance to achieve a high cellulose conversion when lignin removal was limited. SPORL high pH pretreatment removed more lignin but less hemicellulose, while SPORL low pH pretreatment removed about the same amount of lignin and hemicelluloses in lodgepole pine substrates when compared with dilute acid pretreatment. Substrates pretreated with either SPORL process had a much higher cellulose conversion than those produced with dilute acid pretreatment. Lignin removal in addition to removal of hemicellulose in SPORL pretreatment plays an important role in improving the cellulose hydrolysis of the substrate.     

钾元素对生物质主要组分热解特性的影响

采用热重-红外联用仪对松木及生物质主要化学组分半纤维素、纤维素、木质素的热解特性及钾元素对其热解特性的影响进行了研究.结果表明,半纤维素、纤维素、木质素发生热解的主要温度分别为200~350 ℃、300~365 ℃和200~600 ℃;半纤维热解产物中CO、CO₂较多;纤维素热解产物中LG和醛酮类化合物最多;木质素热解主要形成固体产物,气体中CH₄相对含量较高.三种组分共热解过程中发生相互作用使热解温度提高、固体产物增加,气体中CO增加而CH₄减少.添加K₂CO₃后半纤维素和纤维素热解温度区间向低温方向移动,固体产率提高.K对纤维素作用最明显,CO、CO₂气体与固体产物产率明显增加,醛酮类和酸类物质的产率降低;木质素受K影响相对较小,热解固体产物略有增加,挥发分中H₂O和羰基物质增加;三组分共热解减弱了钾元素的催化作用.     

Synchrotron X-ray scattering study of the mechanism of nanopore generation in nanoporous organosilicate thin films imprinted with a reactive six-armed porogen

In situ grazing incidence small-angle X-ray scattering analysis was successfully performed during the thermal processing of film blends of polymethylsilsesquioxane (PMSSQ) precursor and triethoxysilyl-terminated six-arm poly(epsilon-caprolactone) (mPCL6) porogen. In addition, thermogravimetric analysis of the films was carried out in a nitrogen atmosphere. These measurements provide important information about the structures of the blend films and of the resulting porous films. In particular, they are used in this paper to establish the mechanism of the formation of imprinted pores within the blend films. During the heating run, the sacrificial thermal degradation of the porogen component commenced at 320 degrees C, generating pores in the resulting cured PMSSQ films. Only very limited porogen aggregation occurred during the blend film formation process (spin-coating and subsequent drying), and these porogen aggregates were of relatively small size and narrow size distribution. The observed restriction of the formation of such porogen aggregates was found to result from the favorable hybridization reaction of the porogen's reactive end groups with the reactive functional groups of the PMSSQ precursor, which competes with aggregation via reaction between the porogen molecules. The average radius (or half-size) of the porogen aggregates was in the range 2.45-3.98 nm, depending on the porogen loading (10-40 wt %). The porogen aggregates retained their size and size distribution until thermal degradation, which resulted in the imprinting of nanopores in the cured PMSSQ films with size and size distribution corresponding to those of the porogen aggregates. The porosities of the resulting nanoporous films were in the range 12.4-41.7%, depending on the initial porogen loading.     

Comparison of hydrothermal,hydrotropic and organosolv pretreatment for improving the enzymatic digestibility of bamboo

Pretreatment is the crucial step to disrupt the recalcitrant structure of lignocellulosic biomass for improving the enzymatic hydrolysis efficiency. Typically, hydrothermal, organosolv and hydrotropic pretreatments are environmentally benign and effective methods. In this work, effects of hydrothermal, organosolv and hydrotropic pretreatments on improving enzymatic hydrolysis of bamboo were comprehensively compared. Hydrotropic pretreatment was more effective in removal lignin and xylose from bamboo fiber cell wall. However, the surface coverage by lignin and extractives were dramatically displaced during organosolv pretreatment as investigation by X-ray photoelectron spectroscopy. After pretreatments, the crystallinity of cellulose in pretreated substrates has a significant reduction, and pores were exposed on fiber surface. The residual content of acetyl and phenolic groups in hydrotropic pretreated substrates is lower than organosolv pretreated substrates. In order to deeply assess the delignification of pretreatments, the isolated lignins obtaining from pretreatments process were characterized by Fourier transform infrared spectroscopy also. It was revealed that hydrotropic lignin contained more phenolic hydroxyl group and syringyl units than organosolv lignin. Compared to hydrothermal and organosolv pretreatment, cellulase adsorption capacity of pretreated substrates was notably improved by hydrotropic pretreatment, which indicating the better enzyme accessibility of cellulose. Eventually, the maximum glucose yield was obtained from hydrotropic pretreated substrates.     

Thermodriven Micrometer‐Scale Aqueous‐Phase Separation of Amphiphilic Oligoethylene Glycol Analogues

Thermoresponsive materials with a lower critical solution temperature (LCST) are receiving growing attention, of which examples of non‐polymeric small molecules are limited. Monodisperse oligoethylene glycol amphiphiles that contain aromatic units with a LCST in water have been developed and applied to peptide extraction. Concentration‐dependent hysteretic transmittance changes were observed in response to temperature elevation and reduction. Dynamic light scattering measurements and phase contrast microscopy revealed the formation of micrometer‐sized aggregates upon heating at a concentration above 5.0 mM ; these aggregates self‐assembled to form larger aggregates upon cooling before dissolution. The “interaggregate” interactions are likely to cause the hysteretic behavior. As an application of this thermodriven phase separation, selective extraction of peptide fragments containing high percentages of hydrophobic and aromatic amino acid residues was successfully demonstrated.     

A kinetic study on pyrolysis and combustion characteristics of oil cakes: Effect of cellulose and lignin content

Pyrolysis and combustion characteristics of three different oil cakes such as Pongamia(Pongamia Pinnata),Madhuca(Madhuca Indica),and Jatropha(Jatropha curcas) were investigated in this study.The cellulose and lignin contents of oil cakes play very important role in pyrolysis and combustion processes.A kinetic investigation of three oil cakes was carried out and major part of the samples decomposed between 210℃ and 500℃.Pyrolysis and combustion were carried out with the mixtures of cellulose and lignin chemi...     

Microstructure and stability of a lamellar liquid crystalline and gel phase formed by a polyglycerol ester mixture in dilute aqueous solution

The self-assembly behavior of a commercial mixture of polyglycerol fatty acid esters (PGE) and water is investigated as a function of temperature and surfactant content. The phase diagram of this pseudo-binary mixture was characterized using a combination of cross-polarized light and freeze-fracture electron microscopy (cryo-SEM), X-ray diffraction (XRD), small-angle neutron scattering (SANS), and differential scanning calorimetry (DSC). Our experiments show that the morphology of the supramolecular aggregates is lamellar and present in the form of a continuous or dispersed phase (multilamellar vesicles) depending on the water content of the system. Under the effect of temperature, the short- and long-range order of the bimolecular layers successively changes from a biphasic surfactant dispersion to a lamellar liquid-crystalline (Lalpha) and a stable lamellar gel phase (Lbeta) upon cooling; this transition is found to be irreversible. Formation of the lamellar aggregates can be related to the average molecular structure and shape factor of PGE. The stability of the resulting gel phase (Lbeta) appears to be due to the presence of small amounts of unreacted ionic co-surfactant, namely, fatty acid soaps, in this per se nonionic commercial mixture.     

Novel thermoresponsive block copolymers having different architectures—structural,rheological, thermal,and dielectric investigations

Thermoresponsive block copolymers comprising long, hydrophilic, nonionic poly(methoxy diethylene glycol acrylate) (PMDEGA) blocks and short hydrophobic polystyrene (PS) blocks are investigated in aqueous solution. Various architectures, namely diblock, triblock, and starblock copolymers are studied as well as a PMDEGA homopolymer as reference, over a wide concentration range. For specific characterization methods, polymers were labeled, either by partial deuteration (for neutron scattering studies) or by fluorophores. Using fluorescence correlation spectroscopy, critical micellization concentrations are identified and the hydrodynamic radii of the micelles, r _h ^mic , are determined. Using dynamic light scattering, the behavior of r _h ^mic in dependence on temperature and the cloud points are measured. Small-angle neutron scattering enabled the detailed structural investigation of the micelles and their aggregates below and above the cloud point. Viscosity measurements are carried out to determine the activation energies in dependence on the molecular architecture. Differential scanning calorimetry at high polymer concentration reveals the glass transition of the polymers, the fraction of uncrystallized water and effects of the phase transition at the cloud point. Dielectric relaxation spectroscopy shows that the polarization changes reversibly at the cloud point, which reflects the formation of large aggregates upon heating through the cloud point and their redissolution upon cooling.     

Effect of alkaline ultrasonic pretreatment on crystalline morphology and enzymatic hydrolysis of cellulose

In this study, ultrasound-assisted alkaline pretreatment is developed to evaluate the morphological and structural changes that occur during pretreatment of cellulose, and its effect on glucose production via enzymatic hydrolysis. The pretreated samples were characterized using scanning electron microscopy, infrared spectroscopy, and X-ray diffraction to understand the change in surface morphology, crystallinity and the fraction of cellulose Iβ and cellulose II. The combined pretreatment led to a great disruption of cellulose particles along with the formation of large pores and partial fibrillation. The effects of ultrasound irradiation time (2, 4 h), NaOH concentration (1–10 wt%), initial particle size (20–180 μm) and initial degree of polymerization (DP) of cellulose on structural changes and glucose yields were evaluated. The alkaline ultrasonic pretreatment resulted in a significant decrease in particle size of cellulose, besides significantly reducing the treatment time and NaOH concentration required to achieve a low crystallinity of cellulose. More than 2.5 times improvement in glucose yield was observed with 10 wt% NaOH and 4 h of sonication, compared to untreated samples. The glucose yields increased with increase in initial particle size of cellulose, while DP had no effect on glucose yields. The glucose yields exhibited an increasing tendency with increase in cellulose II fraction as a result of combined pretreatment.     

The surface and solution properties of dihexadecyl dimethylammonium bromide

The surface adsorption behavior and solution aggregate microstructure of the dichain cationic surfactant dihexadecyl dimethylammonium bromide (DHDAB) have been studied using small angle neutron scattering (SANS), light scattering, neutron reflectivity (NR), and surface tension (ST). Using a combination of surface tension and neutron reflectivity, the DHDAB equilibrium surface excess at saturation adsorption has been measured as 2.60 +/- 0.05 x 10 (-10) mol.cm (-2). The values obtained by both methods are in good agreement and are consistent with the values reported for other dialkyl chain surfactants. The critical aggregation concentration (CAC) values obtained from both methods (NR and ST) are also in good agreement, with a mean value for the CAC of 4 +/- 2 x 10 (-5) M. The surface equilibrium is relatively slow, and this is attributed to monomer depletion in the near surface region, as a consequence of the long monomer residence times in the surfactant aggregates. The solution aggregate morphology has been determined using a combination of SANS, dynamic light scattering (DLS), cryogenic transmission electron microscopy (CryoTEM), and ultrasmall angle neutron scattering (USANS). Within the concentration range 1.5-80 mM, the aggregates are in the form of bilamellar vesicles with a lamellar " d-spacing" of the order of 900 A. The vesicles are relatively polydisperse with a particle size in the range 2000-4000 A. Above 80 mM, the bilamellar vesicles coexist with an additional L beta lamellar phase.     

Self-assembly prismatic aggregates formed during the calcination of ZnO powders: in situ monitoring by ETA technique and their photocatalytic properties

This paper describes a unique phenomenon occurred during the calcination of ZnO powders, i.e., the ZnO particles self-assembled to form prismatic aggregates with a clear edges and faces. Field-emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) were used to characterize the particle morphology and crystal structure of the calcined sample. The emanation thermal analysis (ETA) technique was used to monitor the changes of ZnO particle surface and subsurface microstructure irregularities and the occurrence of interparticle compaction phenomena under in situ conditions of heating and cooling. It was assumed from the ETA results that the driven force of the self-assembly of ZnO particles towards prismatic aggregates originated from the solid state diffusion and migration of grain boundaries. The photocatalytic tests indicated that the prismatic aggregates of ZnO calcined at 800 degrees C demonstrated a highest photocatalytic activity for acetaldehyde decomposition because of the enhancement of the surface-exposed high-active crystal face of (101 0).     

Effects of Liquid Hot Water Pretreatment on Enzymatic Hydrolysis and Physicochemical Changes of Corncobs

Liquid hot water (LHW) pretreatment is an efficient chemical-free strategy for enhancing enzymatic digestibility of lignocellulosic biomass for conversion to fuels and chemicals in biorefinery. In this study, effects of LHW on removals of hemicelluloses and lignin from corncobs were studied under varying reaction conditions. LHW pretreatment at 160 °C for 10 min promoted the highest levels of hemicellulose solubilization into the liquid phase, resulting into the maximized pentose yield of 58.8% in the liquid and more than 60% removal of lignin from the solid, with 73.1% glucose recovery from enzymatic hydrolysis of the pretreated biomass using 10 FPU/g Celluclast?. This led to the maximal glucose and pentose recoveries of 81.9 and 71.2%, respectively, when combining sugars from the liquid phase from LHW and hydrolysis of the solid. Scanning electron microscopy revealed disruption of the intact biomass structure allowing increasing enzyme’s accessibility to the cellulose microfibers which showed higher crystallinity index compared to the native biomass as shown by x-ray diffraction with a marked increase in surface area as revealed by BET measurement. The work provides an insight into effects of LHW on modification of physicochemical properties of corncobs and an efficient approach for its processing in biorefinery industry.     

The role of lignin in the production process and characterization of lignocellulose nanofibril suspensions

Lignocellulose nanofibrils (LCNFs) are nano-objects that contain lignin. The presence of lignin in the fibrils affects the process production of cellulose nanofibrils. It modifies the morphology of fibrils produced and the rheological behavior of suspensions, which is crucial in developing applications for this material. This work aims to understand the role of lignin in the mechanical-enzymatic production process of LCNFs and the morphological, superficial, and rheological properties of LCNF suspensions. Lignin has a negative effect on the mechanical and enzymatic processes, generating larger fibrils with less homogeneous size distributions and with lower zeta potential. In addition, the composition of the fibrils changes, part of the lignin is removed and dispersed into the solvent in the form of lignin nanoparticles. These nanoparticles are neutral and can be deposited on the surface of the fibrils. Regarding rheological properties, fibrils with lignin are less flexible than bleached fibrils. Such characteristics are due to the cementing capacity of lignin, which increases the hydrodynamic volume that these structures occupy per unit mass. Furthermore, in the semi-dilute region, lignin acts as a control agent for the viscosity in the suspensions due to its hydrophobic characteristic, which forms weak aggregates, poorly hydrated, and hydrodynamically smaller, which generate less resistance to flow.