Binary and ternary LLE data of the system (ethylbenzene + styrene + 1-ethyl-3-methylimidazolium thiocyanate) and binary VLE data of the system (styrene + 1-ethyl-3-methylimidazolium thiocyanate)

The distillation of close boiling mixtures may be improved by adding a proper affinity solvent, and thereby creating an extractive distillation process. An example of a close boiling mixture that may be separated by extractive distillation is the mixture ethylbenzene/styrene. The ionic liquid 1-ethyl-3-methylimidazolium thiocyanate ([EMIM][SCN]) is a promising solvent to separate ethylbenzene and styrene by extractive distillation. In this study, (vapour + liquid) equilibrium data have been measured for the binary system (styrene + [EMIM][SCN]) over the pressure range of (3 to 20) kPa and binary and ternary (liquid + liquid) equilibrium data of the system (ethylbenzene + styrene + [EMIM][SCN]) at temperatures (313.2, 333.2 and 353.2) K. Due to the low solubility of ethylbenzene in [EMIM][SCN], it was not possible to measure accurately VLE data of the binary system (ethylbenzene + [EMIM][SCN]) and of the ternary system (ethylbenzene + styrene + [EMIM][SCN]) using the ebulliometer. Because previous work showed that the LLE selectivity is a good measure for the selectivity in VLE, we determined the selectivity with LLE. The selectivity of [EMIM][SCN] to styrene in LLE measurements ranges from 2.1 at high styrene raffinate purity to 2.6 at high ethylbenzene raffinate purity. The NRTL model can properly describe the experimental results. The rRMSD in temperature, pressure and mole fraction for the binary VLE data are respectively (0.1, 0.12 and 0.13)%. The rRMSD is only 0.7% in mole fraction for the LLE data.     

Separation of benzene from alkanes by solvent extraction with 1-ethylpyridinium ethylsulfate ionic liquid

The (liquid + liquid) equilibrium (LLE) data for ternary mixtures {alkane + benzene + 1-ethylpyridinium ethylsulfate ([EPy][EtSO₄])} at T = (283.15 and 298.15) K and atmospheric pressure are presented. The alkanes used were hexane and heptane. The cloud point method was used to determinate the binodal curve, and the tie-line compositions were obtained by density measurements. The LLE data obtained were used to calculate distribution coefficients and selectivity values. The consistency of tie-line data was ascertained by applying the Othmer-Tobias and Hand equations. Correlation of the experimental tie-lines was conducted through the use of NRTL equation, which provides good correlation of the experimental data.The results show that [EPy][EtSO₄] can be used as an alternative solvent in liquid extraction processes for the removal of benzene from its mixtures with alkanes.     

Thermodynamic properties of the N-octylquinolinium bis{(trifluoromethyl)sulfonyl}imide

This work is a continuation of our wide ranging investigation on quinolinium based ionic liquids (ILs). The study includes specific basic characterisation of the synthesized compounds N-octylquinolinium bromide, [OQuin][Br] and N-octylquinolinium bis{(trifluoromethyl)sulfonyl}imide [OQuin][NTf₂] by NMR spectra, elementary analysis and water content. Differential scanning calorimetry (DSC) measurements gave us properties of the pure [OQuin][NTf₂] i.e. melting and glass-transition temperatures, the enthalpy of fusion as well as heat capacity at the glass transition. Densities and viscosities were determined as a function of temperature. The temperature-composition phase diagrams of 10 binary mixtures composed of organic solvent dissolved in the IL: {[OQuin][NTf₂] + aromatic hydrocarbon (benzene, or thiophene, or toluene, or ethylbenzene, or n-propylbenzene), or an alcohol (1-butanol, or 1-hexanol, or 1-octanol, or 1-decanol, or 1-dodecanol)} were measured at ambient pressure. A dynamic method was used over a broad range of mole fractions and temperatures from (250 to 370) K. For mixtures with benzene and alkylbenzenes, the immiscibility gap in the liquid phase in a low mole fraction of the IL was observed with upper critical solution temperature (UCST) higher than the boiling point of the solvent. In the system with thiophene, the immiscibility gap is lower and UCST was measured. For binary mixtures with alcohols, complete miscibility in the liquid phase was observed for 1-butanol and 1-hexanol. In the systems with longer chain alcohols, the immiscibility gap with UCST was noted. Typical behaviour for ILs was observed with an increase of the chain length of an alcohol the solubility decreases. The well-known NRTL equation was used to correlate experimental (solid + liquid), SLE and (liquid + liquid), LLE phase equilibrium data sets.     

(Liquid + liquid) extraction of methanol from alkanes using dialkylphosphate-based ionic liquids as solvents

In this work, the feasibility of ionic liquids (ILs), 1,3-dimethylimidazolium dimethylphosphate ([MMIM][DMP]), 1-ethyl-3-methylimidazolium diethylphosphate ([EMIM][DEP]), and 1-butyl-3-methylimidazolium dibutylphosphate ([BMIM][DBP]), as solvents for the extraction of methanol from its mixtures with hexane and heptane was analyzed. The knowledge of (liquid + liquid) equilibria (LLE) of these mixtures is necessary for the design of the extraction separation process. Hence, the LLE data for the ternary systems, {methanol + hexane + ([MMIM][DMP], or [EMIM][DEP], or [BMIM][DBP])}, and {methanol + heptane + ([MMIM][DMP], or [EMIM][DEP], or [BMIM][DBP])}, were measured at T = 298.2 K and atmospheric pressure. The experimental results were correlated with the thermodynamic nonrandom two-liquid (NRTL) model. The solute distribution ratios of methanol and methanol/alkane selectivities, derived from the experimental LLE data, were calculated and analyzed to evaluate the capability of the studied ILs to accomplish the separation target. Meanwhile, these capabilities were also compared with that of other ILs obtained from the literature.     

Phosphoric-based ionic liquids as solvents to separate the azeotropic mixture of ethanol and hexane

Ethanol and hexane mixtures are present in industrial processes producing oxygenated additives for unleaded gasoline. The separation of ethanol and hexane is important but challenging due to the formation of an azeotropic mixture. This research focuses on the study of phosphoric-based ionic liquids (ILs) as green solvents for the separation of ethanol from hexane in a liquid extraction process. The knowledge of the (liquid + liquid) equilibrium (LLE) of this mixture is essential for the design of the extraction separation technique. Hence, the experimental determination of the LLE data for the ternary system {ethanol + hexane + 1,3-dimethylimidazolium dimethylphosphate ([MMIM][DMP])}, {ethanol + hexane + 1-ethyl-3-methylimidazolium diethylphosphate ([EMIM][DEP])} and {ethanol + hexane + 1-butyl-3-methylimidazolium dibutylphosphate ([BMIM][DBP])} at T = 303.2 K and atmospheric pressure was carried out. The reliability of the experimental LLE data was confirmed by applying the Othmer–Tobias and Hand equations, and the NRTL model was used to correlate the experimental results for the studied ternary system. The solute distribution ratio and selectivity, derived from the experimental LLE data, were calculated and analyzed evaluate the capacity of the investigated ILs as solvents in liquid extraction process. This capacity was also compared with that of other ILs. The experimental results show that the studied ILs can be suitable solvents in a (liquid + liquid) extraction for the separation of azeotropic mixtures of ethanol and hexane.     

Thermodynamic properties of the N-butylisoquinolinium bis(trifluoromethylsulfonyl)imide

A new isoquinolinium ionic liquid (IL) has been synthesised as a continuation of our work with quinolinium-based ionic liquids (ILs). The work includes specific basic characterization of synthesized compounds: N-isobutylquinolinium bromide, [BiQuin][Br] and N-isobutylquinolinium bis{(trifluoromethyl)sulfonyl}imide [BiQuin][NTf₂] by NMR spectra, elementary analysis and water content. The basic thermal properties of the pure [BiQuin][NTf₂], i.e. melting and glass-transition temperatures, the enthalpy of fusion as well as heat capacity at glass transition have been measured using a differential scanning microcalorimetry technique (DSC). Densities and viscosities were determined as a function of temperature. The temperature-composition phase diagrams of 8 binary mixtures composed of organic solvent dissolved in the IL: {[BiQuin][NTf₂] + aromatic hydrocarbon (benzene, or toluene, or ethylbenzene, or n-propylbenzene), or an alcohol (1-butanol, or 1-hexanol, or 1-octanol, or 1-decanol)} were measured at ambient pressure. A dynamic method was used over a broad range of mole fraction and temperature from (270 to 320) K. For all the binary systems with benzene and alkylbenzenes, the eutectic diagrams were observed with an immiscibility gap in the liquid phase existing at low mole fraction of the IL with a very high upper critical solution temperature (UCST). For mixtures with alcohols, complete miscibility was observed for 1-butanol and also an immiscibility gap with UCST in the liquid phase for the remaining alcohols. The typical dependence was observed that with increasing chain length of an alcohol, the solubility decreases. The well-known NRTL equation was used to correlate experimental (solid + liquid), SLE and (liquid + liquid), LLE phase equilibrium data sets.     

Quaternary (liquid + liquid) equilibrium data for the extraction of toluene from alkanes using the ionic liquid [EMim][MSO4]

(Liquid + liquid) equilibrium (LLE) studies for the extraction of aromatics from alkanes present in the petroleum fractions are important to develop theoretical/semiempirical (liquid + liquid) equilibrium models, which are used in the design of extraction processes. In this work, the ionic liquid 1-ethyl-3-methylimidazolium methylsulfate, [EMim][MSO₄], was evaluated as potential solvent for the separation of toluene from heptane and cyclohexane. The LLE data for the quaternary system {heptane (1) + cyclohexane (2) + toluene (3) + [EMim][MSO₄] (4)} were experimentally determined at T = 298.15 K and atmospheric pressure. Moreover, the LLE data for the ternary systems {heptane or cyclohexane (1) + toluene (2) + [EMim][MSO₄] (3)} were also determined. Solute distribution ratios and selectivities were calculated and analysed in order to evaluate the capability of the ionic liquid to accomplish the separation target. A comparison between the solute distribution ratios and selectivities for the quaternary and the ternary systems was also made. Finally, the experimental tie-line data were correlated with the NRTL model.     

Separation of benzene from alkanes using 1-ethyl-3-methylpyridinium ethylsulfate ionic liquid at several temperatures and atmospheric pressure: Effect of the size of the aliphatic hydrocarbons

The ionic liquid 1-ethyl-3-methylpyridinium ethylsulfate, [EMpy][ESO₄], was studied for the separation of benzene from aliphatic hydrocarbons (octane or nonane) by solvent extraction through the determination of the (liquid + liquid) equilibrium (LLE) of the ternary systems: {octane (1) + benzene (2) + [EMpy][ESO₄] (3)} and {nonane (1) + benzene (2) + [EMpy][ESO₄] (3)} at T = (283.15 and 298.15) K and atmospheric pressure. Binodal curves were determined using the “cloud point” method, and tie-line compositions were obtained by density measurements. The values of selectivity and distribution coefficient, derived from the tie-line data, were used to decide if this ionic liquid can be used as potential solvent for the separation of benzene from aliphatic hydrocarbons using liquid extraction. These results were analyzed and compared to those previously reported for the systems {hexane + benzene + [EMpy][ESO₄]} and {heptane + benzene + [EMpy][ESO₄]}. The experimental results show that this ionic liquid is suitable for the extraction of benzene from mixtures containing octane and nonane. The consistency of tie-line data was ascertained by applying the Othmer–Tobias and Hand equations. The experimental results for the ternary systems were well correlated with the NRTL model. No literature data were found for the mixtures discussed in this paper.     

Separation of toluene from alkanes using 1-ethyl-3-methylpyridinium ethylsulfate ionic liquid at T = 298.15 K and atmospheric pressure

In this paper, the separation of toluene from aliphatic hydrocarbons (heptane, or octane, or nonane) was analyzed by solvent extraction with 1-ethyl-3-methylpyridinium ethylsulfate ionic liquid, [EMpy][ESO₄]. Liquid?liquid equilibrium (LLE) data for the ternary systems {heptane (1) + toluene (2) + [EMpy][ESO₄] (3)}, {octane (1) + toluene (2) + [EMpy][ESO₄] (3)}, and {nonane (1) + toluene (2) + [EMpy][ESO₄] (3)} were obtained by measurements at T = 298.15 K and atmospheric pressure. The selectivity, % removal of aromatic, and solute distribution ratio, obtained from experimental equilibrium results, were used to determine the ability of [EMpy][ESO₄] as a solvent. The degree of consistency of the experimental LLE values was ascertained using the Othmer–Tobias and Hand equations. The experimental results for the ternary systems were correlated with the NRTL model. Finally, the results obtained were compared with other ionic liquids and other solvents.     

Thermophysical properties and phase equilibria study of the binary systems {N-hexylquinolinium bis(trifluoromethylsulfonyl)imide + aromatic hydrocarbons,or an alcohol}

The new quinolinium ionic liquid has been synthesised as a continuation of our work with quinolinium-based ionic liquids (ILs). The work includes specific basic characterisation of synthesized compounds: N-hexylquinolinium bromide, [HQuin][Br] and N-hexylquinolinium bis{(trifluoromethyl)sulfonyl}imide [HQuin][NTf₂] by NMR spectra, elementary analysis and water content. The basic thermal properties of the pure [HQuin][NTf₂] i.e. melting and glass-transition temperatures, the enthalpy of fusion as well as heat capacity have been measured using a differential scanning microcalorimetry technique (DSC) and thermal analysis instrument (TA). Densities and viscosities were determined as a function of temperature. Phase equilibria for the binary systems: {[HQuin][NTf₂]) + aromatic hydrocarbon (benzene, or toluene, or ethylbenzene, or n-propylbenzene), or an alcohol (1-butanol, or 1-hexanol, or 1-octanol, or 1-decanol)} have been determined at ambient pressure. A dynamic method was used over a broad range of mole fractions and temperatures from (270 to 320) K. For all the binary systems with benzene and alkylbenzenes, the eutectic diagrams were observed with immiscibility gap in the liquid phase beginning from (0.13 to 0.28) mole fraction of the IL with very high an upper critical solution temperature (UCST). For mixtures with alcohols, the complete miscibility was observed for 1-butanol and immiscibility with UCST in the liquid phase for the remaining alcohols. The typical dependence was observed, that with increasing chain length of an alcohol the solubility decreases. The well-known NRTL equation was used to correlate experimental (solid + liquid), SLE and (liquid + liquid), LLE phase equilibria data sets. For the systems containing immiscibility gaps, (IL + an alcohol) parameters of the LLE correlation were used to the prediction of SLE.     

Extraction of toluene from aliphatic compounds using an ionic liquid as solvent: Influence of the alkane on the (liquid + liquid) equilibrium

In this paper, the feasibility of using 1-ethyl-3-methylimidazolium ethylsulfate ionic liquid, [EMim][ESO₄], as solvent for the extraction of toluene from aliphatic compounds (hexane, heptane, octane, or nonane) was analyzed. (Liquid + liquid) equilibrium (LLE) data for the ternary systems {alkane (1) + toluene (2) + [EMim][ESO₄] (3)} were measured at T = 298.15 K and atmospheric pressure. Selectivity and solute distribution ratio were calculated from the experimental LLE data, and the obtained values were compared to those previously reported using other ionic liquids and sulfolane. The degree of consistency of the experimental LLE data was ascertained using the Othmer–Tobias equation. Finally, the experimental LLE data were satisfactorily correlated with NRTL and UNIQUAC models.     

The buffering-out effect and phase separation in aqueous solutions of EPPS buffer with 1-propanol, 2-propanol,or 2-methyl-2-propanol at T = 298.15 K

Buffering-out is a new liquid–liquid phase separation phenomenon observed in mixtures containing a buffer as a mass separating agent. The (liquid + liquid) equilibrium (LLE) and (solid + liquid + liquid) equilibrium (SLLE) data were measured for the ternary systems {3-[4-(2-hydroxyethyl)piperazin-1-yl]propanesulfonic acid (EPPS) buffer + 1-propanol, 2-propanol, or 2-methyl-2-propanol + water} at T = 298.15 K under atmospheric pressure. The phase boundary data were fitted to an empirical equation relating to the concentrations of organic solvent and buffer. The effective excluded volume (EEV) values of EPPS were obtained from the phase boundary data. The phase-separation abilities of the investigated aliphatic alcohols were discussed. The reliability of the experimental tie-lines was satisfactorily confirmed by the Othmer–Tobias correlation. The experimental tie-lines data for the ternary systems have been correlated using the NRTL activity coefficient model. The separation of these aliphatic alcohols from their azeotropic aqueous mixtures is of particular interest to industrial process. The addition of the EPPS as an auxiliary agent breaks the (1-propanol + water) and (2-methyl-2-propanol + water) azeotropes. The possibility of using the new phase separation systems in the extraction process is demonstrated by using different dyestuffs.     

Separation of toluene from cyclic hydrocarbons using 1-butyl-3-methylimidazolium methylsulfate ionic liquid at T = 298.15 K and atmospheric pressure

In this paper the extraction of toluene from cyclic hydrocarbons (cyclohexane, or methylcyclohexane, or cyclooctane, or cyclohexene) was analyzed by liquid extraction with 1-butyl-3-methylimidazolium methylsulfate ionic liquid, [BMim][MSO₄], as solvent. The experimental (liquid + liquid) equilibrium (LLE) data were determined at T = 298.15 K and atmospheric pressure. Solubility curves were obtained by the cloud point method and tie-line compositions were determined by density measurement. An analysis of the influence of different cyclic hydrocarbons on the extraction was performed.The effectiveness of the extraction of toluene from cyclic hydrocarbons was evaluated by means of the solute distribution ratio and selectivity values. The degree of consistency of the experimental LLE data was ascertained using the Othmer–Tobias and Hand equations. The experimental data for the (liquid + liquid) equilibria of the ternary systems were correlated with the Non-Random Two-Liquid (NRTL) and UNIversal QUAsi-Chemical (UNIQUAC) thermodynamic models.     

Phase equilibria study of the binary systems (ionic liquid + thiophene): Desulphurization process

(Solid + liquid) equilibria (SLE) and (liquid + liquid) equilibria (LLE) for the binary systems: {ionic liquid (IL) N-butyl-4-methylpyridinium tosylate (p-toluenesulfonate) [BM⁴Py][TOS], or N-butyl-3-methylpyridinium tosylate [BM³Py][TOS], or N-hexyl-3-methylpyridinium tosylate [HM³Py][TOS], or N-butyl-4-methylpyridinium bis{(trifluoromethyl)sulfonyl}imide [BM⁴Py][NTf₂], or 1,4-dimethylpyridinium tosylate [M^1,4Py][TOS], or 2,4,6-collidine tosylate [M^2,4,6Py][TOS], or 1-ethyl-3-methylimidazolium thiocyanate [EMIM][SCN], or 1-butyl-3-methylimidazolium thiocyanate [BMIM][SCN], or 1-hexyl-3-methylimidazolium thiocyanate [HMIM][SCN], or triethylsulphonium bis(trifluoromethylsulfonyl)imide [Et₃S][NTf₂] + thiophene} have been determined at ambient pressure. A dynamic method was used over a broad range of mole fractions and temperatures from (270 to 390) K. In the case of systems (pyridinium IL, or sulphonium IL + thiophene) the mutual immiscibility with an upper critical solution temperature (UCST) was detected at the very narrow and low mole fraction of the IL. For the binary systems containing (imidazolium thiocyanate IL + thiophene), the mutual immiscibility with the lower critical solution temperature (LCST) was detected at the higher mole fraction range of the IL. The basic thermal properties of the pure ILs, i.e. melting and glass-transition temperatures as well as the enthalpy of fusion have been measured using a differential scanning microcalorimetry technique (DSC). The well-known NRTL equation has been used to correlate experimental SLE/LLE data sets.     

Phase equilibria study of the binary systems (1-butyl-3-methylimidazolium tosylate ionic liquid + water,or organic solvent)

(Solid + liquid) phase equilibria (SLE) and (liquid + liquid) phase equilibria (LLE) for the binary systems: ionic liquid (IL) 1-butyl-3-methylimidazolim tosylate (p-toluenesulfonate) {[BMIM][TOS] + water, an alcohol (ethanol, or 1-butanol, or 1-hexanol, or 1-octanol, or 1-decanol), or n-hexane, or an aromatic hydrocarbons (benzene, or toluene, or ethylbenzene, or propylbenzene, or thiophene)} have been determined at ambient pressure. A dynamic method was used over a broad range of mole fractions and temperatures from (230 to 340) K. For the binary systems containing water, or an alcohol, simple eutectic diagrams were observed with complete miscibility in the liquid phase. As usual, with increasing chain length of the alcohol the solubility decreases. In the case of mixtures {IL + n-hexane, or benzene, or alkylbenzene, or thiophene} the eutectic systems with mutual immiscibility in the liquid phase with an upper critical solution temperature (UCST) were detected. The basic thermal properties of the pure IL, i.e. melting and glass-transition temperatures, as well as the enthalpy of fusion have been measured using a differential scanning microcalorimetry technique (DSC). Density at high temperatures was determined and extrapolated to 298.15 K. Well-known UNIQUAC, Wilson and NRTL equations have been used to correlate experimental SLE data sets for alcohols and water. For the systems containing immiscibility gaps {IL + n-hexane, or benzene, or alkylbenzene, or thiophene}, parameters of the LLE correlation equation have been derived using only the NRTL equation.     

(Liquid + liquid) equilibria for ternary mixtures of (alkane + benzene + [EMpy] [ESO4]) at several temperatures and atmospheric pressure

In this work, the separation of benzene from aliphatic hydrocarbons (hexane, or heptane) is investigated by extraction with 1-ethyl-3-methylpyridinium ethylsulphate ionic liquid, [EMpy][ESO₄]. (Liquid + liquid) equilibria (LLE) data are determined for the ternary systems: {hexane (1) + benzene (2) + [EMpy][ESO₄] (3)} at T = (283.15, 293.15, 298.15, and 303.15) K and {heptane (1) + benzene (2) + [EMpy][ESO₄] (3)} at T = (283.15 and 298.15) K and atmospheric pressure. The selectivity and distribution coefficient, derived from the tie line data, were used to determine whether the ionic liquid is a good solvent for the extraction of aromatic from aliphatic compounds. The consistency of the tie line data was ascertained by applying the Othmer–Tobias and Hand equations. The experimental results for the ternary systems were well correlated with the NRTL equation. A study of the temperature effect and the influence of the chain length of the alkanes were realized. The results obtained were compared with other ionic liquids. There are no literature data for the mixtures discussed in this paper.     

Evaluation of [bmim][PF6] as an ionic solvent for the extraction of propylbenzene from aliphatic compounds

The evaluation of using 1-butyl-3-methylimidazolium hexaflurophosphate ionic liquid, [bmim][PF₆], as a solvent for the extraction of propylbenzene from aliphatic compounds was studied. The (liquid + liquid) equilibrium (LLE) for two ternary systems comprising {dodecane or tetradecane + propylbenzene + [bmim][PF₆]} were analysed at atmospheric pressure and two temperatures, (313 and 333) K. The consistency of the experimental tie line data was ascertained by applying the Othmer–Tobias correlation. The effect of temperature, n-alkane chain length and solvent to feed ratio upon solubility, distribution ratio, selectivity, and per cent removal of the aromatic were investigated. The experimental LLE data were correlated using the UNIQAC and NRTL models for the activity coefficient with estimation of new interaction parameters, using the simplex minimization method and a composition based objective function. The calculated results from both methods are considered satisfactory.     

Phase equilibria of didecyldimethylammonium nitrate ionic liquid with water and organic solvents

The phase diagrams for binary mixtures of an ammonium ionic liquid, didecyldimethylammonium nitrate, [DDA][NO₃], with: alcohols (propan-1-ol, butan-1-ol, octan-1-ol, and decan-1-ol): hydrocarbons (toluene, propylbenzene, hexane, and hexadecane) and with water were determined in our laboratory. The phase equilibria were measured by a dynamic method from T = 220 K to either the melting point of the ionic liquid, or to the boiling point of the solvent. A simple liquidus curve in a eutectic system was observed for [DDA][NO₃] with: alcohols (propan-1-ol, butan-1-ol, and octan-1-ol); aromatic hydrocarbons (toluene and propylbenzene) and with water. (Solid + liquid) equilibria with immiscibility in the liquid phase were detected with the aliphatic hydrocarbons heptane and hexadecane and with decan-1-ol. (Liquid + liquid) equilibria for the system [DDA][NO₃] with hexadecane was observed for the whole mole fraction range of the ionic liquid. The observation of the upper critical solution temperature in binary mixtures of ([DDA][NO₃] + decan-1-ol, heptane, or hexadecane) was limited by the boiling temperature of the solvent.Characterisation and purity of the compounds were determined by elemental analysis, water content (Fisher method) and differential scanning microcalorimetry (d.s.c.) analysis. The d.s.c. method of analysis was used to determine melting temperatures and enthalpies of fusion. The thermal stability of the ionic liquid was resolved by the thermogravimetric technique–differential thermal analysis (TG–DTA) technique over a wide temperature range from (200 to 780) K. The thermal decomposition temperature of 50% of the sample was greater than 500 K.The (solid + liquid) phase equilibria, curves were correlated by means of different G^Ex models utilizing parameters derived from the (solid + liquid) equilibrium. The root-mean-square deviations of the solubility temperatures for all calculated data are dependent upon the particular system and the particular equation used. Comparison of the solubilities of different ammonium salts in alcohols, in hexane, in benzene, and in water are discussed.     

Phase equilibria for ternary liquid systems of (water + tetrahydrofuran + nonprotic aromatic solvent) at T = 298.2 K

(Liquid + liquid) equilibrium (LLE) data of the solubility curves and tie-line end compositions are presented for mixtures of {water (1) + tetrahydrofuran (2) + xylene or chlorobenzene or benzyl ether (3)} at T = 298.2 K and P = (101.3 ± 0.7) kPa. Among the studied C6 ring-containing aromatic solvents, xylene gives the largest distribution ratio and separation factors for extraction of tetrahydrofuran. A solvation energy relation (SERLAS) has been used to estimate the (liquid + liquid) equilibria of associated systems containing a nonprotic solvent. The tie-lines were also predicted using the UNIFAC-original model. The reliability of both models has been analyzed against the LLE data with respect to the distribution ratio and separation factor. SERLAS matches LLE data accurately, yielding a mean error of 9.9% for all the systems considered.     

Mixing and decomposition behavior of {[4bmpy][Tf2N] + [emim][EtSO4]} and {[4bmpy][Tf2N] + [emim][TFES]} ionic liquid mixtures

Mixing ionic liquids (ILs) has been revealed as a useful way to finely tune the properties of IL-based solvents. The scarce available studies on IL mixtures have shown a quasi-ideal behavior of their physical properties. In this work, we have performed a thermophysical characterization of two binary IL mixtures, namely {4-methyl-N-butylpyridinium bis(trifluoromethylsulfonyl)imide ([4bmpy][Tf₂N]) + 1-ethyl-3-methylimidazolium ethylsulfate ([emim][EtSO₄])} and {[4bmpy][Tf₂N] + 1-ethyl-3-methylimidazolium 1,1,2,2-tetrafluoroethanesulfonate [emim][TFES]}. Both binary IL mixtures have been recently proposed as promising solvents in the (liquid + liquid) extraction of aromatic hydrocarbons from mixtures with alkanes. Densities, viscosities, refractive indices, thermal stability, and specific heats of the {[4bmpy][Tf₂N] + [emim][EtSO₄]} and {[4bmpy][Tf₂N] + [emim][TFES]} IL mixtures have been measured as a function of both temperature and composition. Dynamic viscosities, refractive indices, and thermal stability of the {[4bmpy][Tf₂N] + [emim][EtSO₄]} mixture have exhibited strong deviations from the ideality, in contrast with the quasi-ideal properties of the {[4bmpy][Tf₂N] + [emim][TFES]} mixture and the behavior of the imidazolium and pyridinium-based IL mixtures studied hitherto. The reliability of predictive methods of the thermophysical properties of the mixtures has also been evaluated.