Salting-out thin-layer chromatography of transition metal complexes. IV: Effect of sorbent on the behaviour of mixed aminocarboxylato cobalt (III) complexes

Summary From literature data for 14 mixed aminocarboxylato cobalt(III) complexes, the effect of the sorbent on R_M values, salting-out efficiency (m) and separation factors () of adjacent members of homologous series was investigated in salting-out, thin-layer chromatography on silica gel, polyacrylonitrile and cellulose sorbents, using ammonium sulphate solutions as developers. For complexes belonging to the same homologous series, linear dependence was found between R_M,m and log values, respectively, on two different sorbents. Polyacrylonitrile was shown to be the most suitable sorbent for the separation of the complexes since it gave the highest values for R_M,m and .     

Poly(ethylene glycol) as Impregnator for Silica Gel in Salting-Out Thin-Layer Chromatography of Some Co(III) Complexes

Silica gel impregnated with poly(ethylene glycol) of different molecular mass (400, 1000, 1540, 4000, and 5500) was investigated for salting-out thin-layer chromatography of 15 mixed aminocarboxylato Co(III) complexes using eight ammonium sulphate solutions as mobile phases. Regularities established earlier for non-impregnated adsorbents are also valid in this work. Poly(ethylene glycol) of high molecular mass increases the hydrophobicity of the adsorbent. Positive linear dependence of R_M values and of salting-out efficiency on average poly(ethylene glycol) molecular mass was usually observed. In contrast with non-impregnated silica gel, separation was achieved between complexes with the smallest hydrocarbon groups.     

Use of Different Salt Solutions in Salting-Out TLC of Co(III) Complexes on Silica Gel

Saturated aqueous solutions of 28 different salts have been studied as a potential mobile phases for salting-out thin-layer chromatography, on silica gel, of a series of four mixed bis-aminocarboxylato cobalt(III) complexes. In addition, by linear regression analysis of chromatographic data obtained for fifteen mixed aminocarboxylato Co(III) complexes (four series) with solutions of ammonium chloride, three alkali metal chlorides, and four alkaline earth metal chlorides, four linear dependences previously established on different adsorbents with (NH₄)₂SO₄ solutions were confirmed. The qualities of the separations achieved with the salts were compared and Li⁺, Mg²⁺, and Ca²⁺ chlorides are proposed as the most suitable.     

Specific retention behaviour of metal (III) tetraphenylporphyrins in non-aqueous,reversed high-performance liquid chromatography

Summary The Co(II), Ni(II), Fe(III) and V(IV) complexes of tetraphenylporphine (TPP) can be eluted at short retention times from a LiChrosorb RP-18 column with pure ethanol. However, both Mn(III) and Co(III) complexes of metal TPP chloride type are so strongly retained on the column that they cannot be eluted. While the retention of other metal teraphenylporphine complexes was not affected, that of the metal(III) complexes of the TPP chloride type especially MnTPPCl and CoTPPCl, decreases dramatically with an increase in the concentration of NH₄Cl added into the mobile phase; a linear relationship between logk' and log[NH₄Cl], with the slope of about–1, has been observed for these two metal(III) complexes in the NH₄Cl concentration range from 2.5×10^–4 to 1.3×10^–2 mol/l. Thus, the specific control of the retention of the metal(III) complexes is enabled by conditioning the NH₄Cl content of the mobile phase, and the chromatographic separation is demonstrated.     

金属螯合亲和色谱中的疏水作用

通过考察盐溶盐和盐析盐浓度对蛋白质在IDA裸柱和金属螯合柱上保留行为的影响,详细研究了金属螯合色谱中的疏水作用,疏水作用的发生、形成的条件以及不同条件下对蛋白质保留值的贡献。实验结果表明,在高浓度和低浓度的盐溶盐以及低浓度盐析盐中,蛋白质在金属螯合柱上的保留主要受静电和配位作用控制,而疏水作用对蛋白质的保留影响很小。对弱亲和性的金属螯合柱以静电作用为主,其大小可用参数Q表征;对强亲和性的IDA-Cu（Ⅱ）柱以配位作用为主。仅在高浓度的盐析盐中,金属螯合柱才呈现较强的疏水作用,支配蛋白质保留。实验证明,金属螯合色谱中疏水作用主要来自固定相间隔臂中的疏水碳链和盐析盐对蛋白质的增疏作用,利用这种疏水作用有可能改善金属螯合色谱分离的选择性。     

Die Reaktion von Eisen(III) mit Brenzkatechin-3,5-disulfonsäure (Tiron) und Äthylendiamintetraessigsäure

The Reaction of Iron(III) with Catechol-3,5-Disulphonic Acid (Tiron) and Ethylene Diamine-Tetracetic Acid In the system iron(III)-Tiron-EDTA a ternary chelate could be detected besides the well known complexes in a weak acid solution. By means of spectro-photometric measurements under various conditions (concentration of ligands) we found [FeHYL]^4? with λ_max = 555 nm und ε₅₅₅ = 2500 l · mol^?1 · cm^?1. The formation of the ternary chelate is an inner-complex reaction of displacing, in which donor atoms of the EDTA in FeY^? are replaced by Tiron. By graphic methods the equilibrium constants could be calculated from the measurements.     

Thin-layer chroamtography of pt-metals complexes with ketoanils: Analysis and effect of chelate ring contraction on RF values

Summary Thin-Layer chromatogrtaphy on silica gel was used for the separation of platinum group metal complexes using one-, two-, and three-component solvent systems. In octahedral and square planar, cationic complexes, containing two identical five-membered chelate rings formed by three different ketoanils, a linear dependence on chelate ring contraction (and also metal-ligand bond frequencies and ligand field parameters) of their R_F values has been established in one-component solvent systems.     

Preparation and properties of some water-soluble cobalt (III)–poly-4-vinylpyridine complexes

Water-soluble cobalt(III) chelates having a polymeric ligand such as cis-[Co(en)_2-PVPCl]Cl₂ and cis-[Co-(trien)PVPCl]Cl₂ (PVP = poly-4-vinylpyridine) were prepared by substitution reactions between cobalt(III) chelate and PVP in water–alcohol solution. PVP of different degrees of polymerization was used as the ligand in preparation of these complexes. The PVP complexes were identified and their properties ascertained by microanalysis and by a study of the infrared, ultraviolet, visible, and PMR spectra. Most of the characteristic properties of these complexes may be ascribed to the polymeric structure of the PVP ligand.     

Linear relation between RM values obtained in salting-out planar chromatography and mol % ammonium sulphate in aqueous solvent systems

Summary Existence of a linear relation between R_M and mol % ammonium sulphate in an aqueous solvent system, established earlier for mixed aminocarboxylato cobalt(III) complexes in salting-out, thin-layer chromatography on silica gel, polyacrylonitrile and cellulose, was verified by linear regression analysis of the corresponding data reported in the literature for 108 organic compounds separated on cellulose. The same regularity was also found for seven inorganic anions.     

A calorimetric study on the relative thermal stabilities of some cobalt(III)-tris(diamine) and -bis(triamine) complexes in the solid phase

The enthalpy changes for the reaction of [Co(AA)₃]X₃ and [Co(dien)₂]X₃ type complexes with an alkaline sodium sulfide solution were calorimetrically measured at 25°C, where AA is the diamine such as en, pn, tn, bpy or phen and X is Cl, Br, NO₃, I or ClO₄. The thermal stabilities were found to decrease in the following orders: chloride > bromide > nitrate > iodide > perchlorate; aliphatic diamine > aromatic diamine complexes; five-membered chelate > six-membered chelate compounds; and tris(diamine) > bis(triamine) complexes.     

Vibrational study on the cobalt binding mode of Carnosine

The Co(II)-l-Carnosine (Carnos) system was investigated at different pH and metal/ligand molar ratios by Raman and IR spectroscopy. Raman spectra present some marker bands yielding information on the ability of the Co(II)/Carnos system to bind molecular oxygen and to identify the metal co-ordination site of the imidazole ring (N_π or N_τ atom) of Carnos.The existence of different oxygenated species is greatly affected by pH and the structure of the predominant complexes depends on the available nitrogen atoms. Under basic conditions, binuclear complexes binding molecular oxygen are the predominant species and two forms (monobridged and dibridged) were identified by the Raman νO-O band (750-850 cm⁻¹).Decreasing pH to 7, the species present in the system are less able to bind oxygen. Hydrogen peroxide and a Co(III) chelate not binding O₂, were formed with a significant conversion of peroxo into superoxo complexes. A slight excess of Carnos does not enhance metal chelation.In slightly acidic conditions, the formation of H₂O₂ and superoxo species is more enhanced than at pH 7 and another Co(III) chelate is probably formed.     

Size and stability of chelate rings in coordination compounds of cobalt(II), manganese(II), iron(III) and palladium(II) with vicinal oxime-imine ligands

Summary Two types of the Co^II complexes L¹Co (H₂L¹=N,N-ethylenebis(isonitrosoacetylacetoneimine) were prepared. In type (a) the chelate rings are five-membered whereas in type (b) they are six-membered. The type (b) complexes were converted to type (a) in refluxing solutions. Half-ionization of the ligand is observed in the complexes HL¹ Co(O₂CMe) and HL¹MnCl, where the chelate rings are five- and six-membered respectively. The octahedral complex L¹FeCl·H₂O has chelate rings of type (a) as does the complex L²Co (H₂L²=unsymmetric Schiff baseN,N-ethylene(isonitrosoacetylacetoneimineacetylacetoneimine). Twocis complexes (L_a ²L_b ³)Pd and (L_a ³)₂Pd are characterized (HL³=isonitrosoacetylacetoneimine, (a) and (b) denote the type of chelate ring). Structures for the metal complexes and the sizes of the chelate rings are suggested on the basis of analytical and spectral evidence.     

Thin Layer Chromatographic Detection and Separation of Metal Ion Complexes with Tridentate Schiff Base

The Tridentate chelating, system present in Salicylidine o-amino benzoic acid was used for complexation with Cu (11), Ni (11), Co (11) and Pd (11). The thin-layer chromatographic (TLC) detection and separation of these complexes on Silica gel (G) layers was studied. The coloured spots of the complexes were quite visible without any visualizing agent. A maximum of four complexes could be resolved and identified. The coloured zones were eluted with solvent and characterise by elemental analysis and spectral studies. Colour of the complexes at λ_max was measured.     

Thermal and spectral studies on complexes derived from tetradentate Schiff bases

Several new complexes of Schiff bases ligands H₄La and H₄Lb with transition metal ions such as Cr(III), Fe(III), Co(II) and Zn(II) are synthesized. Elemental analysis, infrared, UV–Vis and thermal analysis, as well as conductivity and magnetic susceptibility measurements are used to elucidate the structure of the newly prepared metal complexes. A square planar geometry is suggested for Zn(II) complexes, while an octahedral geometry suggested for the Cr(III), Fe(III) and Co(II) complexes. The thermal decomposition of complexes was found to be first order reaction and the thermodynamic parameters corresponding to the different decomposition steps were reported.     

Reactions of cobalt(III) complexes with free radicals derived from thymine

The nature of interaction of Co(III) complexes such as Co(III)EDTA and Co(III)NTA with transient adducts of thymine such as TOH^˙, T^˙?, and TH^˙ formed in the gamma radiolysis of thymine were studied. The study shows that TOH radicals do not undergo electron transfer reaction with Co(III) complexes whence no radiosensitization of thymine by Co(III) complexes was observed. Electron transfer however, takes place from T^˙? and TH^˙ to Co(III) complexes. A plausible mechanism of radiolysis of thymine in presence of Co(III) complexes is discussed. © 1994 John Wiley & Sons, Inc.     

Separation selectivity of anionic metal complexes of N,N'-bis(hydroxybenzyl)ethylenediamine-N,N'-diacetic acid in ion and ion electrokinetic chromatography

The complexes of Fe(III), Co(III), Mn(III), Al(III), Cu(II), Ni(II), Cd(II) and Zn(II) with N,N'-bis(hydroxybenzyl)ethylenediamine-N,N'-diacetic acid (HBED) were separated by ion exchange in different modes: ion chromatography (IC) and ion electrokinetic chromatography (IEKC). In column IC these complexes were separated on an IonPac AS4a anion-exchange column (Dionex, USA). Parameters of the background electrolyte that were examined in IEKC mode include polymer, competing ion concentration and pH. The use of poly(diallyldimethylammonium chloride) (PDADMACl) as a modifier in IEKC provides separation selectivity only slightly different from that observed in IC on the IonPac AS4a column. Optimal separation conditions were found to be: 0.1 mM HBED, 50 mM PDADMAOH, 10 mM Na2 B4 O7, pH adjusted to 10 with acetic acid. The use of an aromatic ligand allowed a 10-fold decrease in detection limits of metal ions in comparison with previously studied EDTA. A separation efficiency up to 400,000 theoretical plates was demonstrated for IEKC.     

Solvent extraction of trivalent lanthanide Pr(III), Ho(III) and Er(III) with N-benzoyl-N-phenylhydroxylamine

Extraction of Pr(III), Ho(III) and Er(III) has been studied in the pH range of 1–10 with N-benzoyl-N-phenylhydroxylamine (BPHA) in benzene. The separation was found to be quantitative in borate media from pH 7 to 10, at an ionic strength of 0.1M (H⁺, BO₃ ^3–). The stoichiometric composition of the complexes under the optimal conditions of shaking time, pH and reagent concentration was formulated using slope analysis and found to be M(BPHA)₃, where M=Pr(III), Ho(III) and Er(III). The effect of various masking agents shows that citrate, ascorbate, EDTA, oxalate, fluoride and phosphate form stable complexes with these rare earths as compared to BPHA. The decontamination factors for different cations with respect to these rare earths under the optimum conditions have been evaluated.     

Application of zone-melting technique to metal chelate systems-XI Refining of tetrakis(di-n-propionylmethanato)zirconium(IV) from hafnium and trace amounts of some other metals

The zone-melting method was applied to purification of tetrakis(di-n-propionylmethanato)zirconium(IV) which contained copper(II), nickel(II), cobalt(II and III), iron(III) and hafnium(IV) in the forms of their chelates with the common ligand. All minor components having effective distribution coefficients < 1 in the zirconium(IV) chelate were concentrated toward the terminal end of the refining column. When an aqueous solution of zirconium(IV) containing zinC(II) and manganese(II) in addition to the metal contaminants above was treated with di-n-propionylmethane to precipitate the chelate complexes, only zinc, iron and hafnium were found in the precipitated zirconium chelate. The first two were ettectively removed by zone-melting. Though the separation of hafnium was poorer, the technique was efficient enough for practical purposes.     

Quantum chemical calculation of the molecular structures of (666)macrotricyclic chelates of 3D elements in the M(II)-propanedithioamide-formaldehyde systems by the density functional theory method

The nonhybrid OPBE/TZVP density functional theory (DFT) method and the Gaussian09 program package were used to calculate the thermodynamic and geometric parameters of asymmetric macrocyclic M(II) complexes with three six-membered metal rings and (NNNN)-coordination of the donor sites of the ligand. The complexes are formed upon self-assembly (template synthesis) of hexacyanoferrates(II) of the corresponding M(II), propanedithioamide H₂N-C(=S)-CH₂-C(=S)-NH₂, and formaldehyde H₂C(=O) in gelatin-immobilized matrix implants. Note that complexes of this type are formed only for M = Ni, Cu, and Zn, while for M = Mn, Co, and Fe, these compounds are unstable. Bond lengths and bond and torsion angles are presented. In each of these complexes, both the MN₄ chelate units and the N₄ units and all sixmembered metal rings were found to be non-coplanar.     

Determination of platinum metals complexes with 2-(6-methyl-2-benzothiazolylazo)-5-diethylaminophenol by reversed-phase high performance liquid chromatography

The use of 2-(6-methyl-2-benzothiazolylazo)-5-diethylaminophenolas a precolumn derivatizing reagent in the reversed-phase high performance liquid Chromatographic separation and determination of Ru(III), Rh(III), Os(IV), Ir(IV), Pt(II), Co(II), Ni(II) and Cu(II) is reported. When the mobile phase consists of methanol-water (76/24% v/v) and 20 mmol/l (pH 5.0) acetate buffer, the eight complexes can be separated within 35 min on a C₈ column. The detection limits are Ru 7.0, Rh 5.1, Os 1.5, Ir 7.6, Pt 3.7, Co 0.62, Ni 0.14 and Cu 1.2 ng/ml, respectively, at a signal-to-noise ratio of 3. RSDs were typically Ca. 1%.