锂在甲烷氧化偶联多元氧化物催化剂中的作用

考察了不同Li含量对Li_xLa_(0.5)Ti_(0.5)系氧化物催化剂的甲烷氧化偶联催化性能的影响；比较了水洗前后LiLa_(0.5)Ti_(0.5)氧化物催化剂的催化活性，并通过XRD、IR、XPS和BET等方法时催化剂进行表征。确认了Li在含稀土、过渡金属多元氧化物中的作用。其中，表面Li的作用是缩小催化剂的比表面积，覆盖表面深度氧化活性位，提高C_2选择性；体相Li的作用是部分取代Ti~(3+)进入LaTiO_3晶格形成LaTi_(1-y)LiyO_(3-λ)活性相，产生甲烷氧化偶联Li~+-O~--Ti~(3+)缺陷簇。(注：Li_xLa_(0.5)Ti_(0.5)和LiLa_(0.5)Ti_(0.5)表示该系列氧化物催化剂制备时的各金属元素的配比。用来表示催化剂的名称，并不表示实际存在的物相，以下类同，下面出现时，不再加以说明。)     

Na^+/CaO催化剂上的甲烷氧化偶联

研究了不同碱金属离子对CaO的促进作用,发现以Na~+的添加效果最好。在此基础上,研究了不同含钠化合物对CaO的促进作用,并用脉冲反应技术研究Na~+/CaO催化剂表面氧物种的特性及其作用。CaO表面上存在非选择性氧化的氧物种。Na~+对CaO的修饰作用是抑制非选择性氧化。当表面上的非选择性氧化的氧物种消耗后,体相的晶格氧会向表面迁移,以补充消耗掉的表面氧物种。消耗掉的表面氧物种也可由气相氧补充。CH_4脉冲和混合气脉冲说明仅靠[Na~+O~-]中心不足以使甲烷转化成C_2产物,必须有气相氧的参与才能使甲烷转化成C_2产物。     

THE ROLE OF LATTICE AND GASEOUS OXYGEN ON THE OXIDATIVE COUPLING OF METHANE STUDIED BY A PULSE REACTION TECHNIQUE

A comparative study of the role of lattice and gaseous oxygen in theoxidative coupling of methane over Na~ /Cao and Ca_xSr_(1-x)TiO_3 perovskiteoxide catalysts was performed by using a pulse reaction technique with CH_4,O_2 and mixtures of CH_4and O_2.It was found that there is an oxygen species onthe Surface of Cao which is active only for the total oxidation of methane at thereaction temperature.These oxygen species.once reacted with methane andconsumed,can be regenerated by the adsorption of oxygen molecules from thegas phase or by the migration of the lattice oxysen from the bulk onto thesurface.In contrast,no such oxygen species and no reaction can be detected bymethane pulsed over Ca_xSr_(1-x)TiO_3perovskite oxide catalysts.Na~ can heavilysuppress the non-selective oxygen species on the surface,and When 5mol%Na~ was incorporated onto the surface of Cao,the sample showed no reactivityto methane.When oxygen exists in the gas phase,or the pulse containsmethane and oxygen,the reaction over(Cao is mai     

Effect of Calcination Temperature and Pretreatment with Reaction Gas on Properties of Co/γ‐Al2O3 Catalysts for Partial Oxidation of Methane

The effects of calcination temperature and feedstock pretreatment on the catalytic performance of Co/γ‐Al₂O₃ catalysts were studied for partial oxidation of methane (POM) to synthesis gas, with emphasis on the role of feedstock pretreatment. The physicochemical properties of the catalysts were characterized by N₂ adsorption, X‐ray diffraction (XRD), transmission electron microscopy (TEM), H₂ temperature‐programmed reduction (H₂‐TPR), and Raman spectroscopy. The results showed that the pretreatment of the catalyst by reaction gas significantly improved the catalytic activity and stability for the POM reaction. On the other hand, the effect of calcination temperature was less significant. Although the initial activity was increased by an increased calcination temperature, the catalyst without the feedstock pretreatment suffered a rapid deactivation. The reaction‐atmosphere pretreatment was revealed as a process that mainly modified the surface structure of the catalyst. In that process, the formation of a CoAl₂O₄‐like compound led to high Co metal dispersion after reduction, and the transformation of the carrier into α‐Al₂O₃ occurred over the catalyst surface. Both the high dispersion of cobalt and the presence of α‐Al₂O₃ surface phase were assumed as the important factors resulting in an excellent catalytic performance in terms of high activity and high stability.     

Ba—La2O3催化剂的表面碱性,活性氧种对甲烷氧化偶联的影响

利用ＣＯ２－ＴＰＤ技术考察了Ｂａ－Ｌａ２Ｏ３系催化剂的表面碱性，实验发现，催化剂表面仅有单一的强碱位或中碱位时，其催化性能均较差。只有表面的中碱位与强碱位以适当量共同存在的样品（６％Ｂａ－Ｌａ２Ｏ３），才能获得好的催化活性和Ｃ２选择性。此碱性特征可能有利于表面活性位的产生。同时利用ＸＲＤ和ＸＰＳ等技术分别对体相结构和表面氧物种进行了研究。结果表明，Ｂａ－Ｌａ２Ｏ３系催化剂表面存在Ｏ２＾２－离子，但     

甲烷氧化偶联催化剂Li/MgO的结构及表面性质的研究

本文用XRD、TEM、XPS和荧光光谱等方法研究了一组不同Li~+含量的Li/MgO催化剂的结构及表面性质,并与它们的氧化偶联甲烷的催化性能相关联。结果表明,低配位O~(2-)(O_(3c)~(2-))是使甲烷活化的活性中心。O_(1s)结合能为531.9eV的氧物种是对甲烷氧化偶联反应的C_2选择性起作用的活性氧物种。     

Tuning the structural and physical properties of Cr2Ti3Se8 by lithium intercalation: a study of the magnetic properties, investigation of ion mobility with NMR spectroscopy and electronic band structure calculations

The room temperature intercalation of Cr2Ti3Se8 with butyl lithium yields a phase mixture of the starting material and of the new trigonal phase with composition Li0.4Cr0.5Ti0.75Se2. The phase pure fully intercalated trigonal phase is obtained at elevated temperature (80 degrees C) with the final composition Li0.62Cr0.5Ti0.75Se2. The line profile analysis (LPA) of the powder patterns shows that pronounced strain occurs in the intercalated material. The deintercalation of the material is realized by treatment of the fully intercalated sample with distilled water leading to the composition Li0.15Cr0.5Ti0.75Se2. The intercalation is accompanied by an electron transfer from the guest Li to the host material, and as a consequence significant changes of the interatomic distances are observed. The local environment and the dynamics of the Li+ ions in the fully intercalated sample were studied with 7Li magic angle spinning (MAS) NMR investigations. These reveal different environments of transition metal neighbors for the Li sites and a high mobility of the Li ions. Magnetic measurements show that in the pristine material antiferromagnetic interactions are dominating (theta = -113.5 K) with no long-range order at low temperatures. The magnetic ground state is characterized by a spin-glass behavior. With increasing Li content the antiferromagnetic character vanishes progressively, and the fully intercalated phase exhibits a positive Weiss constant (theta = 12 K) indicating dominating ferromagnetic exchange interactions; i.e., the magnetic properties can be significantly altered by lithiation. The interpretation of our experimental findings is supported by the results of accompanying band structure calculations done within the framework of local spin density functional theory. These demonstrate in particular the role of the charge transfer between the constituents as a function of the Li concentration and its impact on the exchange coupling.     

Effect of calcination temperature on structure and performance of Ni/TiO2-SiO2 catalyst for CO2 reforming of methane

The influence of calcination temperature on the structure and catalytic behavior of Ni/TiO2-SiO2 catalyst, for CO2 reforming of methane to synthesis gas under atmospheric pressure, was investigated. The results showed that the Ni/TiO2-SiO2 catalyst calcined at 700 ℃ had high and stable activity while the catalysts calcined at 550 and 850 ℃ had low and unstable activity. Depending on the calcination temperature, one, two, or three of the following Ni-containing species, NiO, Ni2.44Ti0.72Si0.07O4, and NiTiO3 were identified by combining the temperature programmed reduction （TPR） and X-ray diffraction （XRD） results. Their reducibility decreased in the sequence： NiO〉Ni2.44Ti0.72Si0.07O4〉NiTiO3. It suggests that high and stable activities observed over the Ni/TiO2-SiO2 catalyst calcined at 700 ~C were induced by the formation of Ni2.44Ti0.72Si0.07O4 and smaller NiO species crystallite size.     

STUDY ON OXID TIVE COUPLING OF METHANE Ⅱ.CATALY TIC PERFORMANCE AND CHARACTERIZATION OF TiO_2-BASED CATALYSTS

The catalytic performance of Mn/TiO_2,La-Mn/TiO_2,Li-La-Mn/TiO_2 etc for the oxidetive coupling of methane(OCM)was investignted.Thecatalysta were cheracterised with X-ray diffraction(XRD)and X-rayphotoelectron spectroscopy(XPS).The results reveal that catalyst Li-La-Mn/TiO_2 exhibits high activity and C_2 selectivity;Ti in this catalyst exists asTi~( 4) state;Li can promote the formation of lanthanum tituate via theinteraction between La and TiO_2;the formed La_2Ti_2O_7 and La_4Ti_9O_(24) aredistributed in the inner surface layer and Mn exists in outer surface layer in lowvalence states.The high activity and C_2 selectivity of catalyst Li-La-Mn/TiO_2are intimately related to the valence states of Mn,Li,La and theirdistribution on the catulyst surface layer.     

固体酸WO3/TiO2负载锂锰催化剂组成对其甲烷氧化偶联反应性能的影响

The selective oxidation of methane to basic petrochemicals (ethylene and ethane) is desirable and has attracted extensive research attention. The oxidative coupling of methane (OCM) is considered a promising one-step route for the production of C₂ compounds (ethylene and ethane) from methane, and has been the focus of industrial and fundamental studies. It is widely accepted that the composition is a crucial factor governing the activity of a catalyst system. It was found that the phase structures, basicity, existing status and distribution of the active components, oxygen species, and chemical states of the catalyst were influenced by the composition and ratio, resulting in different catalytic performances for the OCM. In this study, a series of solid acid WO₃/TiO₂-supported lithium-manganese oxide catalysts for OCM were synthesized via the impregnation method. The impacts of diverse compositions, such as the individual contents (Li and Mn) and dual contents (Li-Mn), on the OCM were investigated in detail, using inductively coupled plasma optical emission spectrometry, X-ray diffraction, high-resolution transmission electron microscopy, CO₂-temperature-programmed desorption, O₂-temperature-programmed desorption, H₂-temperature-programmed reduction, Raman spectroscopy, X-ray photoelectron spectroscopy, and CH₄-temperature-programmed surface reaction. The addition of Li content to the catalyst not only led to the anatase-to-rutile crystal structure transformation of TiO₂, and the reduction of the high-valence-state Mn species to low-valence-state Mn, but also increased the content of surface lattice oxygen and decreased the surface basicity. The observed effects on the structures and catalytic performance suggest that the Li content is helpful in suppressing the formation of completely oxidized CO₂, and increases the C₂ selectivity. Moreover, increasing the Li content of the catalyst facilitated the mobility of the lattice oxygen, which triggered the promotion of CH₄ activation, thereby enhancing the OCM catalytic performance. The Mn content acted as the active sites for OCM; therefore, the performance of the catalyst was closely related to the Mn concentration and valence state. However, the WO₃/TiO₂-supported catalyst with excessive Mn content exhibited a high surface basicity, high valence state of Mn, and low abundant lattice oxygen, which was unfavorable for C₂ selectivity. The Raman spectroscopy results revealed that MnTiO₃ was formed due to the co-existence of Li and Mn on WO₃/TiO₂, and played an essential role in improving the low-temperature OCM performance. There was a synergic effect of the Li and Mn components on the OCM. The optimal performance (16.3% C₂ yield) was achieved over the WO₃/TiO₂-supported lithium-manganese catalyst with n(Li) : n(Mn) = 2 : 1 at 750 ℃.     

红外光谱研究甲烷和氧与SrO-La2O3/CaO表面的相互作用

在甲烷氧化偶联（ＯＣＭ）反应条件下，用原位红外光谱研究ＳｒＯ－Ｌａ２Ｏ３／ＣａＯ催化剂，结果表明，晶格氧使甲深度氧化，Ｌａ２Ｏ３和ＣａＯ具有活泼的晶格氧，ＳｒＯ的晶格氧比较稳定，气相氧通过催化剂表面消耗掉的晶格氧，加速甲烷了深度氧化，另一方面，催化剂表面的碳酸根物种在氧气氛下分解，在Ｌａ２Ｏ３和ＬＣ催化剂中，催化剂表面Ｌａ２Ｏ２（ＣＯ３）的分解形成配位不饱和的晶格氧Ｏ＾２－，并为气相氧吸附提供氧空     

焙烧温度对 MnO2-CeO2/Zr0.25Ti0. 25Al0. 5O1.75 整体式催化剂 NH3 低温选择性催化还原 NO 性能的影响

 采用等体积浸渍法在不同温度下焙烧制备了一系列 MnO2-CeO2/Zr0.25Ti0.25Al0.5O1.75 整体式催化剂样品, 并用低温 N2 吸附-脱附、储氧量、X 射线衍射、X 射线光电子能谱和 NH3 程序升温脱附等对催化剂进行了表征, 考察了催化剂上 NH3 选择性催化还原 (SCR) NO 的活性. 结果表明, 随着焙烧温度的升高, 催化剂的比表面积和孔体积逐渐减小, 平均孔径逐渐增大, 储氧能力逐渐降低. 在 500~700 oC 焙烧时, 催化剂主要以无定形或微晶的形式存在; 在 500 oC 焙烧时, 催化剂表面 Mn 与载体之间的相互作用较强, 表面酸量最高, 有利于提高 SCR 活性. 尽管在 600 和 700 oC 焙烧的催化剂仍具有较高的 SCR 活性, 且表现出一定的抗 H2O 和 SO2 性能, 但活性有所下降. 800 oC 焙烧后催化剂的活性显著降低.     

锂/铌镁催化剂中碳酸锂的熔点与甲烷氧化偶联反应的活化和失活的关系

研究了铌掺杂的Li/MgO甲烷氧化偶联催化剂的反应性质及铌的助剂作用。铌的引入使得该催化剂上甲烷氧化偶联反应的活化温度降低50℃以上, 使此温度降到了催化剂中碳酸锂的熔点附近。试验观察到部分催化剂上甲烷氧化偶联反应的活性曲线在碳酸锂的熔点附近有一转折, 这一转折现象的出现与否及程度取决于制备条件。在碳酸锂的熔点附近, 含有铌的催化剂得到活化, 观察到无稀释气体时的反应引燃现象, 即温度增加几度活性便达到最大值。当在比碳酸锂熔点稍高的温度下且不稀释时反应, 含铌催化剂活性很高但很快失活, 在稍低于此熔点下则不失活, 但活性较低。这些试验结果表明, 含铌催化剂的活化与失活均与催化剂中的碳酸锂的相变化有关。试验还观察到了在稍高于碳酸锂的熔点下做寿命试验时, 甲烷氧化偶联反应的振荡现象。     

CuO/Ce0.5Ti0.5O2的制备与表征及其对NO+CO反应的催化活性

以Ce0.5Ti0.5O2为载体, 采用浸渍法制备了不同负载量的CuO/Ce0.5Ti0.5O2催化剂, 通过TPR、XRD和激光Raman光谱等技术对其进行了表征, 并在色谱-微反装置上考察了催化剂对NO+CO反应催化性能. 结果表明, CuO/Ce0.5Ti0.5O2催化剂对NO+CO反应的活性与CuO负载量有关; 500 ℃焙烧的催化剂, 当CuO的负载量(w)为22%时, 催化剂的活性最好; 14%CuO/Ce0.5Ti0.5O2在700 ℃焙烧具有最佳催化活性, 这可能与复合载体形成了CeTi2O6的结构有关. TPR结果表明, CuO在Ce0.5Ti0.5O2上出现了四种还原能力不同的物种, α和β峰是载体表面高度分散的CuO物种, γ峰是与Ce0.5Ti0.5O2相互作用较强的孤立CuO晶簇的还原峰, δ峰是载体表面晶相CuO的还原峰; XRD结果表明700 ℃焙烧的样品中已出现了新复合氧化物CeTi2O6的晶相峰, 随焙烧温度的升高, 此晶相峰也变得更加明显, 这说明高温焙烧有利于Ce与Ti发生固相反应而形成CeTi2O6结构; Raman结果表明, 焙烧后的Ce0.5Ti0.5O2并不是简单的TiO2和CeO2的复合, 而是形成了新的晶相结构, 这也进一步验证了CeTi2O6结构的生成.     

Nitridation-driven conductive Li4Ti5O12 for lithium ion batteries

To modify oxide structure and introduce a thin conductive film on Li4Ti5O12, thermal nitridation was adopted for the first time. NH3 decomposes surface Li4Ti5O12 to conductive TiN at high temperature, and surprisingly, it also modifies the surface structure in a way to accommodate the single phase Li insertion and extraction. The electrochemically induced Li4+deltaTi5O12 with a TiN coating layer shows great electrochemical properties at high current densities.     

Partial Oxidation of Methane Over the Perovskite Oxides

Introduction The conversion of methane to syngas is a very appealing route for the conversion of the large reserves of natural gas1, from which a wide variety of valuable hydrocarbons and oxygenates, such as methanol and formaldehyde, can be synthesized. A great research effort is presently being carried out on the catalytic partial oxidation of methane to syngas2. In the present work, two oxides with the perovskite structure, Ba0.5Sr0.5Co0.8Fe0.2O3- and Ba0.5Sr0.5Co0.8Ti0.2O3-?were sys…     

在Li2O／MgO上以脉冲法研究甲烷氧化偶联

在Ｌｉ_２Ｏ／ＭｇＯ上以脉冲法研究甲烷氧化偶联戚蕴石，卫上方（华东理工大学工业催化研究所，上海，２００２３７）关键词甲烷氧化偶联，晶格氧，脉冲法对甲烷氧化偶联（ＯＣＭ）的研究已有较多报道［１～４］，对其反应机理的研究亦取得了较大的进展．Ｏｔｓｕｋａ［?..     

CaxLa1-xMnAl11O19 六铝酸盐催化剂上甲烷的催化燃烧

以共沉淀法制备了CaxLa1-xMnAl11O19系列六铝酸盐催化剂,考察了Ca2 部分取代La3 对LaMnAl11O19六铝酸盐的甲烷催化燃烧活性和稳定性的影响以及活性与物理化学性能的关系,用X射线衍射、N2吸附、程序升温还原和透射电镜对其进行了表征.结果表明,当Ca2 加入量过高时,Ca2 不能进入到六铝酸盐骨架中,过量的Ca2 形成CaAl4O7杂相.当x=0.2时,催化剂活性最高,起燃温度为723 K,也提高了样品的热稳定性,1 373 K煅烧后比表面积为26.1 m2/g.Ca2 的加入使六铝酸盐晶粒变薄,这使材料的抗烧结性能增强,比表面积增大,同时Ca2 部分取代La3 使活性Mn3 的含量增加,这两方面的综合作用使得催化剂活性显著提高.对Sr2 ,Ca2 和K 部分取代La3 的六铝酸盐的比较实验结果表明,Ca2 部分取代La3 的样品具有最低的起燃温度.     

甲烷氧化偶联Ti-La-Li系混合氧化物催化剂

研究了Ti-La-Li三元氧化物的组成、结构及其对甲烷氧化偶联反应的催化性能；用XRD、IR、XPS和SEM等方法对催化剂进行表征，结果表明：在LiTi_xLa_(1-x)O_2系列催化剂中，随x值的不同，可生成LaTi_(1－y)Li_yO_(3-λ)、Li_2TiO_3、La_(0.66)TiO_(2.993)、La_2O_3和Li_(1.33)Ti_(1.66)O_4几种物相，其中，钙钛矿到三元复合氧化物LaTi_(1-y)Li_yO_(3-λ)是甲烷氧化偶联反应的主要活性相，活性位Li~＋-O~－-Ti~(3＋)的形成是活性提高的主要原因．Li_2TiO_3和La_(0.66)TiO_(2.993)是深度氧化活性相，而Li_(1.33)Ti_(1.66)O_4既无偶联活性，也无深度氧化活性．     

Synthesis of highly active sulfate-promoted rutile titania nanoparticles with a response to visible light

Highly active sulfate-promoted rutile titania (SO(4)(2-)/TiO(2)) with smaller band gap was prepared by an in situ sulfation method, that is, under moderate conditions, sulfate-promoted rutile titania was directly obtained via precipitating Ti(SO(4))(2) in NaOH solution followed by peptizing in HNO(3) without the phase transformation from anatase to rutile. Thus, the negative impacts of phase transformation from anatase to rutile on the structure, surface, and photoactivity properties of the catalysts due to higher calcination temperature can be avoided. The catalysts were characterized by means of thermal analysis, Brunauer-Emmett-Teller analysis (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), UV-visible spectroscopy, FT-IR pyridine adsorption, and temperature-programmed desorption (TPD). The results show sulfate species are sensitive to the variation of calcination temperature. In the process of peptizing, sulfate species are homogeneously dispersed throughout the bulk of catalysts, allowing sulfate species to penetrate into the network of TiO(2) effectively. After being calcined at 300 degrees C, sulfate species occupy oxygen sites to form Ti-S bonds, as evidenced by XPS results. As calcination temperature is further increased to 600 degrees C or above, the active sulfate species on the catalyst surface are destroyed, and the sulfate species in the network of TiO(2) are expelled out onto the surface to form inactive sulfate species. Thus, Ti(3+) defects will be produced on the catalyst surface. Accompanying this process, surface area is decreased promptly, and crystalline size is greatly increased via two fast growth phases due to the decomposition of sulfate species with different binding forces. Most importantly, the band gap of SO(4)(2-)/TiO(2) is remarkably shifted to the visible light region due to the formation of Ti-S bonds, and with increasing calcination temperature the visible light absorption capability is reduced due to breakage of Ti-S bonds. The excellent photoactivity of 300 degrees C calcined SO(4)(2-)/TiO(2) can be explained by its small crystalline size, high surface area, loose and porous microstructure, and the generation of Br?nsted acidity on its surface.