离子色谱法检测酸性镀铜液中的微量氯离子

采用Na2CO3-NaHCO3为淋洗液和抑制电导检测,对酸性镀铜液中的微量氯离子进行检测。采用AgNO3作为沉淀剂使Cl-分离富集,再用Na2S2O3溶液溶解沉淀后进行检测,可以很好地消除酸性电镀液中高浓度SO4^2-的干扰。该方法线性良好,Cl^-的检出限为0.01μg/mL,回收率在98.6%-101.7%之间,由于该方法能够很好地消除大量SO4^2-的干扰,在电镀铜工业中对酸性镀铜液中氯离子的监控可发挥作用。     

火焰原子吸收法间接测定二氧化硅中的氯

在酸性环境中,氯离子与银离子生成沉淀,经氨水溶解后,以火焰原子吸收法测定银,从而间接测定氯离子的含量。本方法测定氯的线性范围为1.0~30μg/mL,检出限为0.059μg/mL,回收率为95%~105%。将此法应用于二氧化硅中氯离子的测定,结果满意。     

过氧化氢氧化酸性铬兰K催化动力学光度法测定溴离子

在中性条件下,游离的Br-对H2O2氧化酸性铬兰K褪色反应具有催化作用。基于此建立了测定微量Br-的催化光度分析方法。结果表明,该方法最大吸收波长为525 nm,测定的线性范围为0.4μg/mL～11.2μg/mL,检出限为0.321μg/mL。方法用于河水中微量Br-的测定,结果令人满意     

离子色谱法同时测定蛋白胨中氯离子、硫酸根离子、碘离子

建立离子色谱法测定蛋白胨中氯离子、硫酸根离子、碘离子3种阴离子的含量。采用氢氧化钾淋洗液发生器产生的KOH溶液为流动相,进行梯度淋洗,流量为1.0 mL/min。氯离子、硫酸根离子的质量浓度分别在0.5～200μg/mL范围内与色谱峰面积呈良好的线性关系,碘离子的质量浓度在0.75～50μg/mL范围内与色谱峰面积呈良好的线性,线性相关系数均不小于0.999,检出限分别为0.003,0.01,0.22μg/mL。样品加标回收率为92.94%～96.59%,测定结果的相对标准偏差为2.42%～5.70%(n=9)。该方法灵敏、高效,可用于蛋白胨中氯离子、硫酸根离子、碘离子的快速准确测定。     

悬浮进样阻抑火焰原子吸收光谱法测定甘薯粉条中的微量铝

本文利用铝对钙吸收的阻抑效应,建立了悬浮进样-火焰原子吸收光谱法快速测定甘薯粉条中微量铝的方法。结果表明,当底液中的钙为20.0μg/mL时,测定铝的线性范围是0.5~8.0μg/mL,检出限为0.25μg/mL。本法用于三种不同粉条中铝的测定,相对标准偏差为0.7%~1.9%,加标回收率为95%~104%。     

酸性铬兰K催化光度法测定水中的氟含量

研究了稀硫酸介质中,游离的F-对溴酸钾氧化酸性铬兰K褪色反应具有催化作用,基于此建立了测定微量F-的催化光度分析的方法。结果表明,有色溶液的最大吸收波长为523 nm,测定的线性范围为0.2～6.0μg/mL,检出限为0.1031μg/mL。方法用于水中微量F-的测定,相对标准偏差为0.65%～0.76%,回收率99.5%～105%。     

催化光度法测定水中的氟

在中性溶液中,游离的F-对H2O2氧化酸性铬兰K褪色反应具有催化作用,基于此建立了测定微量F-的催化光度分析的新方法.结果表明,有色溶液的最大吸收波长为522 nm,测定的线性范围为0.4～11.2 μg/mL,检出限为9.9×10-4 μg/mL.该法用于水中微量F-的测定,结果令人满意.     

罗丹明6G催化动力学荧光光度法测定水中氟化物

在弱酸性条件下,NaF对KBrO3氧化罗丹明6G的反应具有催化作用,使罗丹明6G的荧光减弱。基于此建立了测定微量氟化物的催化动力学荧光光度分析新方法。结果表明:罗丹明6G溶液的荧光激发波长和发射波长分别为535nm、556nm,测定的线性范围是0.04~2.8μg/mL,检出限为0.038μg/mL。该法可用于水中微量氟化物的测定。     

Cu(Ⅰ)-烯丙基硫脲的络合吸附波

在pH3.3的邻苯二甲酸氢钾底液中,Cu(Ⅰ)-烯丙基硫脲体系有一灵敏的还原波,其单扫导数峰电位E_p=-0.32V(vs.SCE),可用于微量铜的测定。工作曲线线性范围为0.002—0.12μg/mL,检测极限为0.001μg/mL。文中探讨了该波的还原机理,认为是络合吸附波。     

用流动注射分析法测定强碱性阴离子交换树脂的交换容量

建立了快速测定微量氯离子的FIA分光光度法和快速测定强碱性阴离子交换树脂交换容量的FIA法。本方法将离子交换微型柱导入树脂交换容量的测定中 ,不但获得了很好的精度 (RSD <0 .9% ) ,而且使测定效率提高了近 30倍。优选实验得到的最佳测定条件为再生液流速 0 .5mL/min ,再生剂用量 :333mL/ g,再生剂浓度 :3.0 % (W /V) ;样品液流速 :1 .5mL/min ;树脂交换容量测定温度 :2 5℃± 5℃。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.