聚N-甲基苯胺/蒙脱土纳米复合材料的合成及其协同电流变效应

用插层聚合法制备了聚N 甲基苯胺 蒙脱土纳米复合材料微粒 ,通过IR、XRD及TEM对其结构进行了表征 .观察发现聚N 甲基苯胺插入蒙脱土层间后 ,蒙脱土片层间距由 0 96nm扩大至 1 34nm .将其分散在甲基硅油中 (2 0wt% )配制成无水电流变液 ,该复合材料表现出显著的协同效应 ,具有较好的电流变行为 .实验表明在电场作用下聚N 甲基苯胺 蒙脱土纳米复合材料的电流变效应比聚苯胺、蒙脱土都有显著提高 ,在 3kV mm(DC ,74 5s- 1 )时 ,剪切强度达 6 0kPa ;同时抗沉降性极好 ,静置 6 0天沉淀率小于 3% .介电性能测试表明聚N 甲基苯胺 蒙脱土纳米颗粒的介电常数和介电损耗较蒙脱土和聚N 甲基苯胺明显提高 ,电导率也达到了最佳范围 .     

Electrorheological characteristics of polyaniline/titanate composite nanotube suspensions

In this paper, one-dimensional polyaniline/titanate (PANI/TN) composite nanotubes were synthesized by in situ chemical oxidative polymerization directed by block copolymer. These novel nanocomposite particles were used as a dispersed phase in electrorheological (ER) fluids, and the ER properties were investigated under both steady and dynamic shear. It was found that the ER activity of PANI/TN fluids varied with the ratio of aniline to titanate, and the PANI/TN suspensions showed a higher ER effect than that made by sphere-like PANI/TiO₂ nanoparticles. These observations were well interpreted by their dielectric spectra analysis; a larger dielectric loss enhancement and a faster rate of interfacial polarization were responsible for a higher ER activity of nanotubular PANI/TN-based fluids.     

A new approach of enhancing the shear stress of electrorheological fluids of montmorillonite nanocomposite by emulsion intercalation of poly-N-methaniline

Poly-N-methaniline/montmorillonite (PNMA-MMT) nanocomposite particles with high dielectric constant as well as suitable conductivity were synthesized by an emulsion intercalation method and characterized by FT-IR, XRD, and TEM spectrometry, respectively. The electrorheological (ER) properties of the suspensions of PNMA-MMT particles in silicone oil (20 wt%) were investigated under DC electric fields. It was found that the shear stress of poly-N-methaniline/montmorillonite electrorheological fluid (ERF) is 6.0 kPa in 3 kV/mm (74.5 s(-1)), which is 3.6 times that of electrorheological fluid at zero field, and also much higher than that of pure poly-N-methaniline (PNMA) and montmorillonite (MMT). In the range of 10-90 degrees C, the shear stress changes slightly with the temperature. The sedimentation ratio of PNMA-MMT ERF was about 97% after 60 days. Furthermore, the dielectric constant of PNMA-MMT nanocomposite was increased 3.74 times that of PNMA and 1.99 times that of MMT at 1000 Hz, the dielectric loss tangent also increased about 1.58 times that of PNMA. It is apparent that the notable ER effect of PNMA-MMT ER fluid was attributed to the prominent dielectric property of the poly-N-methaniline/montmorillonite nanocomposite particles.     

Controlled preparation of core–shell polystyrene/polypyrrole nanocomposite particles by a swelling–diffusion–interfacial polymerization method

Polystyrene/polypyrrole (PS/PPy) core–shell nanocomposite particles with uniform and tailored morphology have been successfully synthesized using the “naked” PS particulate substrate with the aid of a proposed strategy, the so-called swelling–diffusion–interfacial polymerization method. After initially forming pyrrole-swollen PS particles, diffusion of the monomer toward the aqueous phase was controlled through the addition of hydrochloric acid, eventually leading to its polymerization on the substrate particle surface. This process allows the nanocomposite particles to possess uniform and intact PPy overlayer and affords much more effective control over the structure and morphology of the resultant nanocomposites by simply changing the PS/pyrrole weight ratio or the addition amount of the doping acid. In particular, the nanocomposite particles with a thin, uniform, and intact PPy overlayer and their corresponding PPy hollow particles were obtained at a low addition amount of pyrrole. The resultant nanocomposite particles have been extensively characterized using scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, and thermogravimetry.     

Synthesis of polypyrrole–polycaprolactone composites by emulsion polymerization and the electrorheological behavior of their suspensions

Polypyrrole–polycaprolactone (PPy-PCL) composites were synthesized by emulsion polymerization to improve their mechanical and electrical properties by forming conducting polymer composites and hence enhance the electrorheological (ER) response. Various PPy-PCL composite particles were synthesized by controlling the amount of PCL. The ER response increased with increasing electric field strength and particle volume fraction. A power-law dependence, τ?=?Kφ ^m E ⁿ , showed a good fit to the yield stresses when m?=?2 and n?=?1.5. The dependence of E ^1.5 is consistent with the conduction model and the dependence of φ ² appears to be related to structural changes with the electric field, which leads to many-body interactions between the particles. The ER response also increased with increasing amount of PCL, but the dielectric properties and dc conductivities of the PPy-PCL composite particles and the dielectric properties of the PPy-PCL composite suspensions were not consistent with the ER behavior. However, the particle diameter increased with the increasing amount of PCL, which is consistent with the ER behavior. The ER behavior of various amounts of PCL fits τ?=?85.12d ⁴ E ^3/2 quite well. The proportionality of d ⁴ appears to be due to the many-body interactions between the particles.     

ELECTRORHEOLOGICAL PROPERTIES OF POLYANILINE/PUMICE COMPOSITE SUSPENSIONS

Electrorheological （ER） properties of polyaniline （PAni）, pumice and polyaniline/pumice composites （PAPC） were investigated. Polyaniline and PAni/pumice composite were prepared by oxidative polymerization. PAni/pumice particlesbased ER suspensions were prepared in silicone oil （SO）, and their ER behavior was investigated as a function of shear rate, electric field strength, concentration and temperature. Sedimentation stabilities of suspensions were determined. It has been found that ER activity of all the suspensions increases with increasing electric field strength, concentration and decreasing shear rate. It has shown that the suspensions have a typical shear thinning non-Newtonian viscoelastic behavior. Yield stress of composite suspensions increased linearly with increasing applied electric field strength and with concentrations of the particles. The effect of high temperature on ER activity of purrfice/silicone oil systems was also investigated.     

Electrorheological properties of suspensions of hollow globular titanium oxide/polypyrrole particles

Hollow globular clusters of titanium oxide (TiO₂) nanoparticles were synthesized by a simple hydrothermal method. The prepared particles were consequently coated by in situ polymerization of conductive polymer polypyrrole (PPy) to obtain novel core–shell structured particles as a dispersed phase in electrorheological (ER) suspensions. The X-ray diffraction analysis and scanning electron microscopy provided information on particle composition and morphology. It appeared that PPy coating improved the compatibility of dispersed particles with silicone oil which results in higher sedimentation stability compared to that of mere TiO₂ particles-based ER suspension. The ER properties were investigated under both steady and oscillatory shears. It was found that TiO₂/PPy particles-based suspension showed higher ER activity than that of mere TiO₂ hollow globular clusters. These observations were elucidated well in view of their dielectric spectra analysis; a larger dielectric loss enhancement and faster interfacial polarization were responsible for a higher ER activity of core–shell structured TiO₂/PPy-based suspensions. Investigation of changes in ER properties of prepared suspensions as a function of particles concentration, viscosity of silicone oil used as a suspension medium, and electric field strength applied was also performed.     

Synthesis and characterization of active ester-functionalized polypyrrole-silica nanoparticles: application to the covalent attachment of proteins

Novel ester-functionalized polypyrrole-silica nanocomposite particles were prepared by oxidative copolymerization of pyrrole and N-succinimidyl ester pyrrole (50/50% initial concentrations), using FeCl3 in the presence of ultrafine silica nanoparticles (20 nm diameter). The N-succinimidyl ester pyrrole monomer was prepared in aqueous solution using 1-(2-carboxyethylpyrrole) and N-hydroxysuccinimide in the presence of 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide. The resulting nanocomposites (N-succinimidyl ester polypyrrole-silica) are raspberry-shaped agglomerates of silica sol particles "glued" together by the insoluble poly(pyrrole-co-N-succinimidyl pyrrole). The N-succinimidyl ester polypyrrole-silica particles were characterized in terms of their size, density, copolymer content, and polydispersity. Scanning electron microscopy and disk centrifuge sedimentometry confirmed that the nanocomposite particles had narrow size distributions. X-ray photoelectron spectroscopy analysis indicated a silica-rich surface and a high surface concentration of N-succinimidyl ester groups. These nanoparticles exhibited good long-term dispersion stability. The chemical stability of the ester functions in aqueous media after several weeks of storage was monitored by FTIR spectroscopy. The functionalized nanocomposites were tested as bioadsorbents of human serum albumin (HSA). The very high amount of immobilized HSA determined by UV-visible spectroscopy is believed to be due to covalent binding. Incubation of the HSA-grafted nanocomposite with anti-HSA resulted in immediate flocculation, an indication that they are alternative candidates for visual diagnostic assays.     

Synthesis of Polyacrylic/Silica Nanocomposite Latexes using Static Mixer

Summary: Static mixers (Sulzer Chemtech; SMX) were used to prepare silica/ MMA-co-BA miniemulsions that were polymerized to produce nanocomposite latexes. Acceptable conditions for the formulation of polymerizable nanodroplets were found and subsequently used to produce silica/poly(MMA-co-BA) nanocomposites. The droplet size distribution of the resulting miniemulsions was narrow enough that it could be successfully polymerized. It was found that the droplet size depends on the silica content and increases with increasing the silica concentration. It was also shown that there is a relationship between the droplet size and the viscosity of the dispersed phase. The majority of droplets were nucleated upon polymerization when less than 15% silica was used. However, when the silica content exceeded 15%, the ratio of the number of particles in the final latex to the number of droplets (Np/Nd) increased to value much higher than 1 indicating the occurrence of homogeneous nucleation.     

Improved electrorheological effect in polyaniline nanocomposite suspensions

We prepared polyaniline (PANI)/clay composites that are composed of both PANI-clay nanocomposite particles and pure PANI particles. The PANI-clay nanocomposite particles were made during the polymerization process, wherein PANI particles are attached on the surface of exfoliated clay particles modified by an aminosilane group. The PANI/clay composites were used as electrorheological fluids (ERFs) by dispersing them in silicon oil. The PANI-clay nanocomposite particles, which can form columnar structure under an electric field, strongly enhance the mechanical rigidity of the suspensions. The maximum yield stress of the PANI/clay composite suspensions (15 wt% in silicon oil) was 1.6 kPa at 3 kV/mm, while that of pure PANI was 300 Pa at the same electric field. A mechanism to explain the yield behaviors of the PANI-based nanocomposite suspensions is proposed.     

Preparation and morphology of SiO2/PMMA nanohybrids by microemulsion polymerization

Polymethylmethacrylate/SiO2 nanocomposite particles were prepared through microemulsion polymerization by using the silica particles coated with 3-(trimethoxysilyl) propyl methacrylate (MSMA) in both acidic and alkaline conditions. Core-shell and other interesting morphology nanocomposite particles were obtained depending on the pH of the microemulsion, the amount of silanol, and the coupling agent concentration employed. Then, by combining a modified microemulsion polymerization process, i.e., an additional monomer-adding process, the solid contents of the polymer/inorganic nanocomposite microemulsion could greatly increase. Thus, by adjusting these parameters and polymerization process, it was possible to control the morphology and size of the nanocomposites.     

Electrorheological behavior of suspensions of a substituted polyaniline with long alkyl pendants

The electrorheological (ER) properties of poly(2-dodecyloxyaniline) (PDOA) suspensions in silicone oil were investigated. The ER behavior of such suspensions of polyaniline particles depends on the type of stabilizer and doping or dedoping level. Here we report on the ER behavior of particles of a substituted polyaniline with long alkyl pendants. Rheological measurements were carried out using a rotational rheometer with high-voltage generator in both constant shear stress and rate modes. Suspensions of the as-synthesized polyaniline particles in silicone oil showed a substantial ER response.     

Preparation and characterization of polymer/silica nanocomposites via double in situ miniemulsion polymerization

Polymer/SiO₂ nanocomposite microspheres were prepared by double in situ miniemulsion polymerization in the presence of methyl methacrylate, butyl acrylate, γ‐methacryloxy(propyl) trimethoxysilane, and tetraethoxysilane (TEOS). By taking full advantage of phase separation between the growing polymer particles and TEOS, inorganic/polymer microspheres were fabricated successfully in a one‐step process with the formation of SiO₂ particles and the polymerization of organic monomers taking place simultaneously. The morphology of nanocomposite microspheres and the microstructure, mechanical properties, thermal properties, and optical properties of the nanocomposite films were characterized and discussed. The results showed that hybrid microspheres had a raspberry‐like structure with silica nanoparticles on the shells of polymer. The silica particles of about 20 nm were highly dispersed within the nanocomposite films without aggregations. The transmittance of nanocomposite film was comparable to that of the copolymer film at around 70–80% from 400 to 800 nm. The mechanical properties and the fire‐retardant behavior of the polymer matrix were improved by the incorporation of silica nanoparticles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3128–3134, 2010     

Bidisperse electrorheological fluids using hydrolyzed styrene-acrylonitrile copolymer particles: synergistic effect of mixed particle size

Monodisperse micron-sized styrene-acrylonitrile copolymer (SAN) particles with three different sizes (about 5, 10, and 15 microm) were prepared by a two-step seeded polymerization and used for a study of bidisperse electrorheological (ER) suspensions. The effect of the particle size and the size-mixing fraction on ER properties was studied with varying the size of these monodisperse copolymer particles. When the two particle sizes were mixed, the suspension generally showed a decrease in the shear yield stress, reaching a minimum value. However, a bidisperse ER suspension of large particles containing a small fraction of fine particles showed an interesting synergy effect of size mixing on ER response, giving enhanced yield stresses over the other size-mixing fractions. This synergistic ER suspension also showed a great increase in the viscoelastic property. The current density of suspensions was maximum at the synergistic bidisperse suspension. This synergy effect in a particular bidisperse suspension was investigated in view of the structure model consideration and was concluded to be due to a close packing and a peculiar structural ordering at an optimum size ratio and mixing fraction.     

Inorganic reinforcement in PET/silica electrospun nanofibers

PET/silica nanocomposite fibers of high quality were fabricated from electrospinning by choosing appropriate surface modification of inorganic fillers, solution properties, and processing conditions. The existence of an immobilized layer around silane-modified silica particles in PET fibers was verified by Fourier transform infrared spectroscopy, the results of which confirm previous thermal analysis studies. The influence of silica particles on the crystal growth during isothermal crystallization as well as the phase structure of the crystallized nanocomposite fibers were examined using differential scanning calorimetry. The PET crystallization rate increases significantly with increasing silica content, which indicates that the silica nanoparticles act as an efficient nucleating agent to facilitate PET crystallization. Using Avrami analysis, for the first time, preferred 1-D crystal growth was confirmed for geometrically confined nanocomposite fibers. Addition of silica particles makes the crystal growth more likely to occur in a 1-D manner.     

PREPARATION AND PROPERTIES OF FUMED SILICA/CYANATE ESTER NANOCOMPOSITES

Fumed silica/bisphenol A dicyanate ester（BADCy）nanocomposites were prepared by introducing different contents of nano-sized fumed SiO₂ into the BADCy matrix.Two different average primary particle diameters of 12 and 40 nm were chosen.Dibutyltindilaurate（DBTDL）catalyst was chosen to catalyze the cyanate ester group into triazine group via cyclotrimerization reaction.The SEM micrographs indicated that the fumed SiO₂ particles were homogeneously dispersed in the poly（bisphenol A dicyanate）matrix by means of ultrasonic treatment and the addition of a coupling agent. The FTIR spectroscopy shows that,not only DBTDL catalyzes the polymerization reaction but also-OH groups of the SiO₂ particles surface help the catalyst for the complete polymerization of BADCy monomer.The thermal stability of the cured BADCy can be improved by adequate addition of fumed SiO₂.A slight increase in the dielectric constant and dielectric loss values were identified by testing the dielectric properties of the prepared nanocomposite samples.By increasing the SiO₂ content,there was a slight increasing in the thermal conductivity values of the tested samples.The obtained results proved that the fumed silica/BADCy nanocomposites had good thermal and dielectrical properties and can be used in many applications such as in the thermal insulation field.     

Preparation of poly (styrene-methyl methacrylate)/SiO2 composite nanoparticles via emulsion polymerization. An investigation into the compatiblization

Inorganic/organic nanocomposite systems, in which inorganic particles are encapsulated into the polymer matrix, are new classes of polymeric materials. These materials combine the properties of both components. It means that polymer component with excellent optical property, flexibility and toughness could improve the brittleness of inorganic particles and besides, inorganic particles could increase the strength and modulus of polymers. There are various methods to make these inorganic/organic nanocomposites. One of them is the chemical process, in which polymerization is performed directly in the presence of the inorganic particles. Examples of miniemulsion, suspension or dispersion polymerization can be found in the literature but emulsion polymerization is by far the technique most frequently used.In this work, latex containing nanostructure hybrid of copolymer (styrene, methyl methacrylate, acrylic acid) and inorganic nanoparticles (silica) with core/shell structure was prepared via semi-batch emulsion polymerization. At first, silica nanoparticles were dispersed in water phase in an ultrasound bath to prevent the aggregation of nanoparticles, and then emulsion polymerization was performed in the presence of silica nanoparticles. Related tests and analysis confirmed the success in synthesis of nanostructure hybrids. Induced coupled plasma (ICP) analysis and thermal gravimetric analysis (TGA) showed the presence and amount of silica nanoparticles in the final latex. Dynamic light scattering (DLS) analysis confirmed the presence of 25-35 nm particles in the system and transmission electron microscopy (TEM) showed the core/shell morphology of nanoparticles. It has been shown that with an appropriate surfactant, adjusting the pH of media, using suitable monomers and under controlled conditions, it would be possible to produce stable organic/inorganic composite nanoparticles with core/shell structure. In another attempt and in order to investigate the effect of compatiblizing system, styrene-methyl methacrylate was copolymerized in the presence of modified silica particles with oleic acid as the inorganic dispersed phase at the same condition. Similar characterizations were performed in order to have a worthwhile comparison. The results for the late procedure show the effect of oleic acid in formation of aggregates as the core for polymeric nanocomposite particles.     

Effect of adsorbed water on the electrorheology of silica suspensions

Monodisperse silica particles were formed by hydrolyzing tetraethylorthosilicate in an ethanol solution and the silica suspensions dispersed in a silicone oil were prepared by a different procedure. The effects of adsorbed water on the electrorheological (ER) behavior were studied under oscillatory shear. The amounts of adsorbed water and surface silanol groups were determined by thermogravimetric analysis. The magnitude of the complex viscosity, |η^*|, increases with the application of electric fields. The physically adsorbed water is primarily responsible for the ER effect. However, the fluids containing large amounts of adsorbed water do not always show excellent ER performance. The surface silanol groups have an important role in promoting the ER effect. Not only the amount but also the situation of silanol groups determines the ER activity of adsorbed water.     

Electrorheological properties of suspensions of monodispersed micron‐sized polyaniline composite particles

Monodispersed micron‐sized polyaniline (PANi) composite particles were synthesized by chemically oxidative polymerization of aniline in the presence of functional porous polymer particles. The formation of the PANi‐coated composite particles was confirmed by scanning electron microscopy. Electrorheological (ER) properties of the monosized composite particle suspensions were then investigated under different DC electric fields by altering the particle characteristics. The ER effect of the PANi composite suspensions was largely dependent on the composition ratio (PANi loading), the particle conductivity, and the particle concentration. Dynamic oscillation measurements revealed that the applied electric field induced the viscoelastic property of the ER suspensions by generating the chain structures of the suspended particles. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1163–1170, 2002     

In situ small-angle X-ray scattering studies during the formation of polymer/silica nanocomposite particles in aqueous solution

This study is focused on the formation of polymer/silica nanocomposite particles prepared by the surfactant-free aqueous emulsion polymerization of 2,2,2-trifluoroethyl methacrylate (TFEMA) in the presence of 19 nm glycerol-functionalized aqueous silica nanoparticles using a cationic azo initiator at 60 °C. The TFEMA polymerization kinetics are monitored using ¹H NMR spectroscopy, while postmortem TEM analysis confirms that the final nanocomposite particles possess a well-defined core–shell morphology. Time-resolved small-angle X-ray scattering (SAXS) is used in conjunction with a stirrable reaction cell to monitor the evolution of the nanocomposite particle diameter, mean silica shell thickness, mean number of silica nanoparticles within the shell, silica aggregation efficiency and packing density during the TFEMA polymerization. Nucleation occurs after 10–15 min and the nascent particles quickly become swollen with TFEMA monomer, which leads to a relatively fast rate of polymerization. Additional surface area is created as these initial particles grow and anionic silica nanoparticles adsorb at the particle surface to maintain a relatively high surface coverage and hence ensure colloidal stability. At high TFEMA conversion, a contiguous silica shell is formed and essentially no further adsorption of silica nanoparticles occurs. A population balance model is introduced into the SAXS model to account for the gradual incorporation of the silica nanoparticles within the nanocomposite particles. The final PTFEMA/silica nanocomposite particles are obtained at 96% TFEMA conversion after 140 min, have a volume-average diameter of 216 ± 9 nm and contain approximately 274 silica nanoparticles within their outer shells; a silica aggregation efficiency of 75% can be achieved for such formulations.

SAXS is used to study the formation of polymer/silica nanocomposite particles prepared by surfactant-free aqueous emulsion polymerization of 2,2,2-trifluoroethyl methacrylate in the presence of silica nanoparticles using a azo initiator at 60 °C.