Structure-property relationships in polycaprolactone-polyurethanes

The structure-property relationships of polycaprolactone-based segmented polyurethanes were studied using differential scanning calorimetry (DSC), small-angle x-ray scattering (SAXS), wide-angle x-ray diffraction (WAXD), dynamic mechanical, and stress-strain testing. The materials studied varied in hard-segment type [4,4′-diphenylmethane diisocyanate/butanediol (MDI/BD) or 4,4′-dicyclohexyl methane diisocyanate/butanediol (H₁₂MDI/BD)], soft-segment molecular weight (830 or 2000 MW polycaprolactone), hard-segment content (23–77% by weight), and thermal history. The materials with aromatic (MDI/BD) hard segments had semicrystalline hard-segment domains, while the materials with aliphatic (H₁₂MDI/BD) hard segment had mostly amorphous domains. Materials with the shorter polycaprolactone soft segment (830 MW) exhibited thermal and mechanical behavior which indicated a considerable degree of hard- and soft-segment compatibility. The materials which contained a 2000-MW polycaprolactone soft segment exhibited better-defined microphase separation. SAXS was used to characterize the microphase structure of each system. The effects of hard-segment content and soft-segment molecular weight were similar for the aromatic (MDI) and aliphatic (H₁₂MDI) hard-segment-based block copolymers. Changing the hard segment from aromatic to aliphatic gave materials with larger interfacial area and slightly higher tensile strength. A range of morphologies between isolated hard domains in a rubbery matrix and isolated rubbery domains in a hard matrix was observed.     

Soy-oil-based segmented polyurethanes

Segmented polyurethanes were prepared from soy polyol, diphenyl methane diisocyanate (MDI), and ethylene glycol or butane diol as chain extenders. Samples were prepared with true hard-segment concentrations (HSC) of about 0, 10, and 40%. Both the soft MDI–polyol and hard MDI/diol segments are glassy at room temperature. These samples were also crosslinked through the polyfunctional polyol soft segment. Partial crystallinity and phase separation were detected in samples with 40% HSC, on the basis of DSC data. Small-angle X-ray scattering shows the existence of phase separation with domain sizes of about 10 nm in the 40% HSC samples, but not in the others. The distribution of domain sizes is considerably broader for the ethylene-glycol extended system compared with that for the butane-diol case. Although the presence of hard segments lowers the crosslink density, samples with higher HSC had higher glass transition temperatures, higher strengths, higher moduli, lower swelling, lower elongation at break, and lower impact strengths. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3178–3190, 2005     

Polyurethane cationomers. I. Structure-property relationships

Polyether polyurethane cationomers are prepared using poly (tetramethylene oxide) of molecular weight 2000 as soft segments, N-methyl-diethanolamine as chain extender, glycolic acid as quaternization agent, methyl ethyl ketone as solvent, and three different diisocyanates. The three diisocyanates are 4,4′-diphenylenemethylene diisocyanate (MDI), hexamethylene diisocyanate (HDI), and toluene diisocyanate (TDI). Properties of the films cast from solutions of the three series of ionomers are studied by infrared spectroscopy, dynamic mechanical analysis, thermogravimetric analysis, differential scanning calorimetry, wide angle x-ray diffraction, and tensile elongation testing. In the un-ionized and ionized systems, the hard segments exhibit disordered and ordered arrangements, respectively. Ionization disrupts the order and produces increased cohesion in the hard domains, which have opposing effects on the tensile elongation properties. In the MDI and TDI systems, cohesion is predominant, leading to an increased tensile strength and modulus and decreased elongation at break. But in the HDI system, the disruption of the order is predominant, leading to decreased tensile strength and only insignificant reduction in the elongation at break. In the TDI system, the tensile strength is rather low, which is attributed to the poor order in the hard domains resulting from the high content of the asymmetric 2,4-isomer of the urethane.     

The use of HPLC for the analytical determination of diisocyanates and acid anhydrides in the air of working environments

Abstract

Measurements of airborne concentrations of (monomeric) 2,4- and 2,6-toluene diisocyanate (2,4- and 2,6- TDI), 4,4′ - diisocyanato diphenylmethane (MDI) and phthalic anhydride have been performed at 17 Danish manufactories using these compounds in the production of polyurethane foams, insulating materials, elastomers, coatings, lacquers and glues.

Diisocyanate vapours at workplaces were collected in impingers, containing a solution of 9-(N-methylaminomethyl)-anthracene (1 × 10^?4 M) in toluene. By reaction with this amine compound the diisocyanates are converted to stable urea derivatives. Phthalic anhydride particles were collected on glass fiber filters.

For separation and detection of the diisocyanate derivatives and the phthalic acid formed upon hydrolysis of its anhydride, reversed phase high performance liquid chromatography on a bonded octadecylsilyl phase using isocratic elution with acetonitrile/water and UV-monitoring at Λ = 254 nm were used. The results obtained for each manufactory are presented.     

Thermal analyses of polymers. III. Influence of isocyanate structure on the molecular interactions in segmented polyurethanes,

The thermal responses of various polyurethane elastomers in the form of changes in heat capacity, linear expansion, and tensile strain have been examined. Most of the change which can be attributed to the backbone of polyethylene adipate, found in several modes of thermal analysis, are still apparent, though shifted somewhat, among most of the diisocyanate extended elastomers used in this study. Tolylene diisocyanate extension changes the modulus properties markedly, low modulus properties being observed at ambient temperatures. Both hydrogenated MDI and MDI elastomers show comparable expansion and modulus response, whereas the hydrogenated TDI elastomer does not have the same characteristics as TDI-based elastomers. The thermal properties of the hydrogenated TDI elastomer resemble more those exhibited by the polyol mixture extended with hexamethylene diisocyanate, and in addition this latter elastomer exhibits more crystallinity, as shown by the large endotherm in the specific heat measurement. The structure of the diisocyanate naturally changes the behavior of the hard segment.     

原位聚合法制备纳米二氧化硅/聚氨酯复合树脂

采用高压剪切分散（HPSH）的方法先将纳米SiO2分散在合成聚氨酯原料中,再应用原位聚合的方法制备了纳米SiO2/聚氨酯复合树脂。 用热重分析、动态机械热分析（DMTA）和扫描电子显微镜等测试技术研究了纳米SiO2的用量及其分散方法对聚氨酯树脂的热稳定和力学性能的影响。 结果表明,二苯甲基二异氰酸酯（MDI）中的-NCO和纳米SiO2表面的-OH发生了化学反应,SiO2表面的包覆率约为7%;通过高压剪切分散的方法能够使纳米SiO2在聚氨酯基体中均匀的分散开来,粒径为30~40 nm,而超声处理的纳米SiO2会聚集约为200 nm聚集体。 当SiO2的添加质量分数为3%时复合树脂（HPSH处理SiO2）的拉伸强度和断裂伸长率均达到最大值,分别为84.3 MPa和438.7%。 此外,与纯树脂相比,复合树脂(4%纳米SiO2)的Tg、Td和T-50%分别增加了17.2、9和21 ℃。     

Study of slabstock flexible polyurethane foams based on varied toluene diisocyanate isomer ratios

The morphological features of three flexible slabstock polyurethane foams based on varied contents of 2,4 and 2,6 toluene diisocyanate (TDI) isomers are investigated. The three commercially available TDI mixtures, that is, 65:35 2,4/2,6 TDI, 80:20 2,4/2,6 TDI, and 100:0 2,4/2,6 TDI were used. The foams were characterized at different length scales with several techniques. Differences in the cellular structure of the foams were noted with scanning electron microscopy. Small‐angle X‐ray scattering was used to demonstrate that all three foams were microphase‐separated and possessed similar interdomain spacings. Transmission electron microscopy revealed that the aggregation of the urea phase into large urea‐rich regions decreased systematically on increasing the asymmetric TDI isomer content. Fourier transform infrared spectroscopy showed that the level of bidentate hydrogen bonding of the hard segments increased with the 2,6 TDI isomer content. Differential scanning calorimetry and dynamic mechanical analysis (DMA) were used to note changes in the soft‐segment glass‐transition temperature of the foams on varying the diisocyanate ratios and suggested that the perfection of microphase separation was enhanced on increasing the 2,6 TDI isomer content. The preceding observations were used to explain why the foam containing the highest content of the symmetric 2,6 TDI isomer exhibited the highest rubbery storage modulus, as measured by DMA. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 258–268, 2003     

Crystallization and Properties of Novel Polyurethanes Based on the Chain Extender Ethylene Glycol and Aromatic Diisocyanates of Variable Flexibility

Summary: Novel polyurethane elastomers (PUs) were synthesized with ethylene glycol (EG) as a chain extender. The macrodiol was poly(ethylene adipate) (PEA), MW = 2000 ± 50. Two isocyanates were employed: 4,4′-methylene bis(phenyl isocyanate) (MDI) and 4,4′-dibenzyl diisocyanate (DBDI). The conformational mobility of DBDI causes an unusually wide range of mechanical, physical and chemical properties, associated with the possibility of pronounced phase separation into a domain – matrix morphology, and with a higher tendency to crystallization and self-association by hydrogen bonding. Materials were characterized by wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), dynamic mechanical analyses (DMA), and mechanical measurements. Results were discussed in terms of the effect of PUs crystallinity. In the case where the chain extender–diisocyanate couple was EG-DBDI, the hard segments were observed to crystallize. The DBDI based PUs displayed higher flow stress in the hard phase caused by stronger phase segregation.     

Segmented polyurethanes with 4,4′-bis-(6-hydroxyhexoxy) biphenyl as chain extender. I. Synthesis and characterization of 2,4-tdi-polyurethanes

Polyurethanes composed of 2,4-toluene diisocyanate (TDI), poly (butylene adipate) diols (PBA) of different molecular weights, and 4,4′-bis-(6-hydroxyhexoxy) biphenyl (BHHBP) were prepared by a two-step solution polymerization process. The polyurethanes were char-acterized by elemental analysis, NMR, and SEC. The thermal properties were investigated by DSC, DMA, and optical polarizing microscopy. Dependent on the molecular weight of the PBA, a shift in the glass transition temperature T_g of the polyurethanes has been observed by DSC and DMA. Polyurethanes based on poly (butylene adipate)s of M_n ～ 2000 exhibited a T_g nearly independent on the hard-segment content up to 50% LC hard segments, indicating the existence of mainly phase separated soft and hard segments. By shortening the PBA chain length up to 1,000 and further to 600, the T_g of the polyester soft-segment phase increases with growing hard-segment content, a consequence of enhanced interaction between the hard and soft segments. This tendency is observed to the greatest extent at polyurethanes with the shortest, polyester diol and can be interpreted as a partial miscibility or compatibility of hard and soft segments. Although in polyurethanes with PBA 2000 the mesophase can be proven at a hard-segment content of ～ 40%, its appearance in polyure-thances prepared with PBA 1000 or PBA 600 requires a hard-segment content > 60%. © 1995 John Wiley & Sons, Inc.     

The structure of MDI/BDO-based polyurethanes: Diffraction studies on model compounds and oriented thin films

Polyurethanes based on MDI/BDO are known to crystallize in three distinct forms. Two of these crystal structures, type II and type III, have been characterized by electron and x-ray diffraction experiments on model compounds and oriented thin films of a 77% hard-segment polyurethane elastomer. The model compounds were of the form BDO(MDI/BDO)_n with n = 1, 2, 3. Results from the model compounds indicate that the MDI/BDO repeat crystallizes in the type-II structure, which has a contracted conformation with a monomer repeat length of 1.70 nm. MDI/BDO-based polyurethanes also exhibit the type-II structure under quiescent crystallization conditions. Studies of oriented thin films of an MDI/BDO-based polyurethane indicate that a change in crystal form occurs on stretching to the fully extended monomer conformation. This crystal form is termed type III and has a monomer repeat length of 1.92 nm.     

Identification of polymer building blocks by Py–GC/MS and MALDI-TOF MS

The main goal of this work is to identify polyurethane (PU) building blocks by pyrolysis gas chromatography/mass spectrometry (Py–GC/MS) and matrix-assisted laser desorption/ionization-time of flight mass spectrometry (MALDI-TOF MS). Toluene diisocyanate (TDI) and diphenylmethane diisocyanate (MDI) are widely used polymer building blocks. Py–GC/MS and MALDI-TOF MS were proved to be powerful methods to distinguish TDI-PU and MDI-PU according to the characteristic pyrolysis products and the different repeated units, respectively. In Py–GC/MS, the specific pyrolyzates are TDI for TDI-PU and MDI for MDI-PU. In MALDI-TOF MS, the weights of repeated units are 264?g/mol for TDI-PU and 340?g/mol for MDI-PU.     

Synthesis and DSC study of model hard segments from diphenyl methane diisocyanate and butane diol

Model hard segments having different chain length and chain terminating groups, such as methyl, ethyl, octyl, and octadecyl, have been synthesized from diphenyl-methane diisocyanate (MDI) and butanediol and studied by DSC. In the case of short chain ends (i.e., methyl, ethyl, and octyl), hard segments having up to three MDI units show an increase of melting temperature T_m, while those with octadecyl chain end have T_m increase continuously with the number of MDI units. Enthalpy and entropy decrease with the augmentation of the hard-segment length. Side groups on the chain ends have a great influence on the melting properties.     

Small-angle scattering analysis of hard-microdomain structure and microphase mixing in polyurethane elastomers

The microdomain structure of a series of segmented polyurethane block copolymers is characterized by small-angle x-ray and neutron scattering analyses. The materials contain hard segments formed from 4,4′- diphenylmethane diisocyanate (MDI) and butanediol (BD), and range in hard-segment content from 20 to 80% by weight. The results provide evidence for a transition from discrete to continuous hard-microdomain morphology as the hard-segment content is increased above ca. 50%. The measured concentration dependences of the interdomain spacing, specific interfacial area, diffuse microphase boundary thickness, and scattering invariants are used to examine the validity of present models for hard-microdomain structure. The observed behavior corresponds well with the general predictions of a lamellar model wherein partially coiled hard-segment sequence configurations are allowed. The thickness of the hard microdomains extracted from the model corresponds to approximately four hard-segment repeat units. Scattering invariant calculations are used together with determinations of the soft-microphase glass transition temperatures to examine possible models for microdomain mixing. These calculations suggest that both the hard and soft microphases are phase mixed.     

氨基硅油扩链改性水性聚氨酯的研究

通过将由甲苯二异氰酸酯与聚四氢呋喃,二羟甲基丙酸反应制得的聚氨酯预聚体在低浓度氨基硅油的水乳液中扩链,合成了一种硅氧烷改性的聚氨酯水乳液,并用傅立叶红外光谱,ＥＳＣＡ能谱,接触角仪,电子拉力试验机,吸水率测定及乳液稳定性测试对其进行研究。     

Effects of altered reaction conditions on the synthesis of polyurethane-poly(2,2,2-trifluoroethyl methacrylate) triblock copolymer aqueous dispersion

Polyurethane-poly(2,2,2-trifluoroethyl methacrylate) (PU-PTFEMA) triblock copolymer aqueous dispersions were synthesized by three-step polymerization. In the first step, polyurethane prepolymers (PU) based on 2,4-toluene diisocyanate (TDI), polyether binary alcohol (N₂₂₀), α,α-dimethylol propionic acid (DMPA), hydroxypropyl acrylic acid (HPA), and butanediol (BDO) were prepared with butanediol as the chain extender and methylethylketon as solvent. The next step involved neutralization and dispersion in water, where prepolymers were neutralised by the addition of triethylamine (TEA). The last step was the seeded emulsion polymerization, where PU emulsion was used as seed, kalium persulfate (KPS) as initiator and 2,2,2-trifluoroethyl methacrylate (TFEMA) as comonomer. Factors influencing the synthesis of PU-PTFEMA copolymer aqueous dispersion were studied. Experimental data indicate that factors influencing the synthesis of PU-PTFEMA copolymer aqueous dispersion mainly involve reaction temperature, reaction time, the concentration of initiator, DMPA content, TFEMA content. Rotational viscometer and dynamic light scattering (DLS) were used to characterize the properties of copolymer aqueous dispersion.     

利用“网包法”制备高效液相色谱大环抗生素类手性固定相

万古霉素和替考拉宁都属于糖肽类的大环抗生素，具有立体的环状结构和多个手性中心，是两种常见的手性识别材料，广泛应用于对映体的色谱手性分离分析。该文以万古霉素和替考拉宁为手性选择剂，哌嗪为单体，4，4'-二苯基甲烷二异氰酸酯（MDI）、1，6-己二异氰酸酯（HDI）和2，4-甲苯二异氰酸酯（TDI）为交联剂，通过界面聚合反应形成网状层包裹硅胶载体的方法制得6种高效液相色谱手性固定相，用于分离外消旋化合物，并与MDI直接交联万古霉素和替考拉宁在硅胶表面所得固定相进行了比较。结果表明，利用"网包法"和直接交联法制备的手性柱与商品万古霉素和替考拉宁柱之间具有互补性，均对不同的外消旋体有不同程度的拆分。     

基于聚丙交酯的多嵌段聚氨酯的形状记忆性能和生物相容性

制备了以聚丙交酯(PLA)为软段, 2,4-甲苯二异氰酸酯(TDI)与乙二醇(EG)反应产物为硬段的多嵌段聚氨酯(PLA-PU), 并对其形状记忆效应和生物相容性进行了研究. 形状压缩50%的样品从起始恢复温度(22~37 ℃)开始, 在10 ℃范围内可以恢复到起始形状, 形变恢复率接近100%, 形变恢复力最大值达到1.5~4 MPa. 细胞培养实验结果初步证明PLA-PU的细胞相容性与PLA相当, 因而有可能用作植入形状记忆医疗器械材料.     

Structural and Mechanical Properties of Polybutadiene-Urethane Elastomer

A series of polyurethanes based on hydroxyl-terminated polybutadiene (HTPBD) and cured with Bis-(-hydroxy ethyl)-terephthalate (BHET) have been synthesized. Mechanical, microscopic and kinetic studies were carried out to elucidate the structure-property relationships from the view point of phase separation. We studied the effects of the polymerization method, varying the hard to soft segment ratio and changing the hard-segment domain structure on the properties of the subject materials. Dynamic mechanical responses showed that the Tg of the soft-segment at ?60°C was independent of the hard-segment content, which indicates that the copolymers were well phase separated. A higher hard-segment content brought about a slight increase in the modulus, a moderate increase in the tensile strength and a decrease in the ultimate elongation. The size of the hard-segment domain, as estimated from electron micrographs, ranged from 60A to 100A. It was observed that a higher content of hard-segments causes an increase in the hard-segment domain size. In addition, a general survey of the reaction rate indicated that BHET is less reactive with diphenyl methyl diisocyanate (MDI) than with HTPBD.     

聚醚氨酯的微区形态

<正> 聚醚氨酯热塑弹性体是属于(AB)n类型的线型多嵌段共聚物,包括交替的硬段和软段单元.自从1966年Cooper和Tobolsky首先提出聚氨酯具有微相分离的本体结构之假设以后,至今已有大量文献报道了这类材料结构形态与性能关系的研究结果. Wilkes和Koberstein等使用SAXS研究了聚氨酯体系的形态特征.一般认为,聚氨酯材料的微相结构包括一个叠层状或类似叠层状形态,由相分离的软段和硬段组成,平均尺寸为100A的数量级,在软硬段微区之间还存在一相混合的过渡区,其厚度可以从几个埃至几十个埃.然而,SAXS虽然能够高分辨地给出多相体系相分离情况的定     

A highly sensitive high-performance liquid chromatographic procedure for the determination of isocyanates in air

Summary A sensitive high-performance liquid chromatographic procedure is described to analyse hexamethylene diisocyanate (HDI), 2,4- and 2,6-toluene diisocyanate (TDI), and 4,4-diphenylmethane diisocyanate (MDI) in air. The isocyanates are trapped on a sorbent coated with 1-(2-methoxyphenyl)piperazine (MPP). The resulting derivatives are separated using a column switching technique using either a diode array UV detector or an electrochemical detector. Working ranges are 1–5000 and 0.05–400 pmol for UV and EC detection, respectively. Virtually no breakthrough occurs if an air volume of up to 1500 l is sampled, and relative detection limits between 0.1 and 1 ng/m³ can be achieved. The procedure can be used to determine HDI and MDI in work place atmospheres and indoor air.Dedicated to Prof Dr. E. Lahmann on the occasion of this 65th birthday