聚吡咯/海藻酸钠纳米球的制备及其应用于高性能超级电容器

用海藻酸钠作为结构导向剂,通过原位氧化聚合吡咯法制备了聚吡咯/海藻酸钠(PPy/SA)纳米球.聚吡咯/海藻酸钠纳米球的形貌和结构通过扫描电镜(SEM)、X射线衍射(XRD)和傅里叶变换红外(FTIR)光谱进行表征.材料的电化学性能通过循环伏安法和恒电流充放电方法进行测试.电化学测试表明,聚吡咯/海藻酸钠纳米球在1 mol L-1KCl电解液中,电流密度为1 A g-1时其比电容高达347 F g-1.与纯聚吡咯相比较,聚吡咯/海藻酸钠纳米球具有更优异的循环稳定性能.     

ZnO/PPy异质纳米复合材料的制备、表征及其气敏特性

室温下, 采用原位聚合法, 以吡咯(PY)为单体, 氯化铁(FeCl₃·6H₂O)为氧化剂, 在塑料基片上聚合生长了聚吡咯(PPy)纳米微球. 然后在聚吡咯基片上生长ZnO种子, 将表面种有ZnO种子的PPy元件置于六次甲基四胺与硝酸锌的混合溶液中, 90 ℃水浴中, 在PPy微球上生长了ZnO纳米棒, 合成了PPy/ZnO异质纳米复合材料. 分别通过X射线衍射仪(XRD)和场发射扫描电镜(FESEM)对PPy/ZnO异质纳米复合材料的结构和形貌进行了表征. 制备了塑料基的PPy/ZnO异质纳米复合材料气体传感器, 在室温下, 对10×10^-6-150×10^-6 (体积分数)浓度范围的氨气进行了气敏测试, PPy/ZnO气敏元件对氨气响应的灵敏度基本呈线性关系, 且对甲醇、丙酮、甲苯等有机气体表现出很好的选择性. 最后, 对PPy/ZnO异质纳米复合材料的形成机理进行了简要分析.     

超级电容器用聚吡咯纳米粒子的比容量衰减机理研究

基于化学氧化聚合法制备了粒径约为40nm的掺杂对甲苯磺酸(TSA)的聚吡咯(PPy)复合纳米粒子.采用XRD、EDS、SEM和TEM研究了产物的结构和形貌特征,并用循环伏安、恒流充放电等方法测试了纳米粒子的电化学性能.结果表明PPy/TSA具有良好的快速充放电能力,在10 mA/cm2时比容量达到268Fg-1,但在1000次循环后发现其比容量下降了25.5%.用CV测试了PPy/TSA电极在第一次循环和第1000次循环的伏安曲线图,发现经过1000次循环后PPy/TSA电极的氧化峰逐渐消失,并且非法拉第电流减小.交流阻抗测试表明,PPy/TSA纳米粒子在反复充放电循环后,其界面电荷传递电阻增加,高频段双层电容值降低,但低频段的赝电容值却有所增加.通过比表面积测量发现,聚合物链的反复氧化-还原过程还可导致平均孔径减小、比表面积下降.红外和拉曼光谱也证实PPy纳米粒子在充放电过程中会发生降解,生成一种含氧的醌式结构,这表明聚合物电极材料比容量的下降可能与PPy主链的不可逆氧化和结构碎片化有关.     

聚吡咯/还原氧化石墨烯复合物的合成及电容性能

通过原位聚合方法制备不同配比的聚吡咯/氧化石墨（PPy/GO）复合物,将其用NaBH4还原得到聚吡咯/还原氧化石墨烯(PPy/RGO)复合物,采用X射线衍射、红外光谱和场发射扫描电子显微镜（FESEM）对其结构和形貌进行物理表征。 采用循环伏安、恒电流充放电和交流阻抗等电化学方法系统研究了所制备样品的电化学性能。 实验结果表明,在电流密度为0.5 A/g、吡咯（Py）与GO质量比为95∶5时,得到的复合物还原前后比电容分别可达401.5和314.5 F/g,远高于单纯的GO（34.8 F/g）和PPy（267.5 F/g）。 经过1200圈循环稳定性测试后,PPy/RGO复合物比电容保持了原来的62.5%,与PPy和PPy/GO（电容保持率分别为16.8%和46.4%）相比,PPy/RGO表现出更好的循环稳定性能,有望成为超级电容器电极材料。     

9,10-蒽醌-2-磺酸钠盐掺杂对导电聚吡咯电容性能的促进作用

用恒电位法制成以9,10-蒽醌-2-磺酸钠盐(AQS)为掺杂阴离子的导电聚吡咯(PPy)电化学电容器电极材料,并采用循环伏安(CV)、充放电测试、电化学阻抗(EIS)等方法表征电容性质.结果表明,与高氯酸阴离子(ClO4-)掺杂的PPy相比,PPy/AQS电极材料不仅单位质量电容和电极稳定性得到提高,工作电压范围也得以扩大.在1mol·L-1的氯化钾中,工作电压为-0.6至0.6V,扫描速率为50mV·s-1时其单位质量电容达到491F·g-1,比PPy/ClO4-电极材料提高1.5倍.这是由于AQS自身良好的氧化还原活性和AQS掺杂有利于聚吡咯膜形成疏松多孔的纳米及亚微米颗粒结构而导致的.     

纳米电容器的组建及电化学性能

用逐层组装法在阳极氧化铝模板的纳米孔内制备纳米电容器,其组成为电化学聚合PPy/电沉积TiO2多孔隔膜/化学聚合PPy.该纳米电容器显示了典型的电化学超电容性质,且具有良好的充放电性能.     

MoO3基纳米复合材料的制备及其电化学性能研究

以MoO3为基体,分别用超声分散法与碳纳米管(CNTs),化学原位聚合法与聚吡咯(PPy)复合,制备了MoO3/CNTs,MoO3/PPy和MoO3/CNTs/PPy纳米复合材料。利用XRD、SEM、TEM对复合材料进行物性表征,在1 mol·dm-3的HCl溶液中对MoO3,MoO3/CNTs,MoO3/PPy和MoO3/CNTs/PPy四个样品进行电化学测试。结果表明,复合材料的比容量均高于MoO3,其中,由于MoO3/PPy特殊的一维核壳结构使其具有较高的比表面积,相比较其他复合材料而言,有更好的电化学活性。该材料的最大比电容为450.8F·g-1。     

电化学沉积制备氧化石墨烯/聚吡咯复合材料及其用于超级电容器的研究

本文采用改进的Hummers法制备氧化石墨烯(GO),利用电化学沉积法制备聚吡咯(PPy)和GO/PPy复合材料并对其作为超级电容器电极材料进行了探究。通过XRD、FT-IR、AFM和SEM对其结构和形貌进行了表征,研究表明:PPy成功在GO片层上生长,并改变了原来PPy类逗号形的形貌,形成了无定形结构的GO/PPy复合材料。循环伏安法(CV)对不同电沉积时间的PPy和GO/PPy电容量进行了测试,发现电沉积时间为17min的PPy和GO/PPy均表现出较优的电容性能。在1A/g电流密度下进行恒流充放电(CP)测试,通过比较发现GO/PPy比PPy的比电容量提高了82. 3%,达到332. 37F/g。     

磁性Fe_3O_4-聚吡咯纳米微球的合成与表征

报道了具有核壳结构的Fe3O4 聚吡咯磁性纳米微球的合成方法和表征结果 .微球同时具有导电性和磁性能 .在优化的实验条件下 ,可得到饱和磁化强度为 2 3 4emu g ,矫顽力为 45 2Oe的磁性微球 .微球的导电性随着微球中Fe3O4含量的增加而下降 .微球的磁性能则随着Fe3O4含量的增加而增大 .Fe3O4磁流体的粒径和磁性聚吡咯微球的粒径均在纳米量级 .纳米Fe3O4粒子能够提高复合物的热性能 .实验表明 ,磁流体和聚吡咯之间存在着一定的相互作用 ,正是这种相互作用使磁性聚吡咯纳米微球的热稳定性提高 .     

肝素钠掺杂球状聚吡咯的合成及其电化学电容

以生物制剂肝素钠为掺杂剂,由自组装方法合成出平均粒径为100 nm的球状聚吡咯(PPy),用作超级电容器电极材料.透射电镜(TEM)、循环伏安、恒流充放电和电化学交流阻抗测试表明,肝素钠掺杂聚吡咯呈现较好的形貌和电容性质,在电流密度3 mA/cm2下充放电,单电极比电容达到338 F/g.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.