成膜条件对聚醚砜超滤膜性能和结构的影响

以聚醚砜(PES)为膜材,聚乙二醇600(PEG600)为添加剂,N,N-二甲基甲酰胺(DMF)为溶剂,纯水为凝固浴,用相转化法制备聚醚砜超滤膜.详细探讨了PES浓度、添加剂含量、凝固浴温度对膜性能和结构的影响规律,确定了制备高水通量、高截留率聚醚砜超滤膜的最佳工艺条件.     

非溶剂添加剂对共聚砜铸膜液体系及膜性能与结构的影响

以含二氮杂萘酮结构的新型共聚砜为膜材料 ,通过浊点滴定法和特性粘数的测定研究了几种非溶剂添加剂对铸膜液体系的影响 .并由共聚砜 NMP 添加剂三组分相分离曲线数据计算了共聚砜的Θ溶剂中NMP与添加剂的比例 ,考察了添加剂EGME用量对共聚砜超滤膜结构和性能的影响 .发现当EGME NMP接近Θ组成时膜性能发生突变 ,在EGME NMP低于Θ组成时 ,膜的水通量随添加剂用量的增大而增大 ,截留率基本不变 .     

低截留分子量PPES超滤膜的制备

以杂萘联苯聚醚砜(PPES)为膜材料、N-甲基吡咯烷酮(NMP)为溶剂、有机小分子丙醇(PrOH)和无机小分子氯化锂(LiCl)作为混合添加剂,采用相转化法制备超滤膜.研究了聚合物浓度、混合添加剂配比、凝胶浴温度等对膜结构和性能的影响.结果表明:随聚合物浓度的增大,膜的纯水通量下降,截留率升高;混合添加剂,在PrOH含量为12%、LiCl含量为1.5%时,可制得纯水通量为252 L/(m2·h),对聚乙二醇1000(PEGl000)截留率为96%的超滤膜;随凝胶浴温度的升高,膜的纯水通量增加.     

复合提锂吸附剂的成型工艺及性能研究

针对离子筛成型时成型工艺参数不明确的问题，以Li_1.33Mn_1.67O₄为研究对象，使用反溶剂成型法合成复合吸附剂P-LMO，进行成型工艺及性能的研究。通过对进料管径、进料速度、反溶剂搅拌速度、聚氯乙烯(PVC)的聚合度、PVC和溶剂的配比等因素考察离子筛成型的规律，确定最佳合成条件为进料管径3.2mm、进料速度1～3mL/min、反溶剂搅拌速度50～200rpm、PVC的聚合度1300、PVC和溶剂配比为75mg/mL时，获得粒径为3mm的球形复合吸附剂。通过对比磨损率和硬度确定PVC理论添加量为20%。吸附实验结果表明，在pH=10、锂离子初始浓度为150mg/L的溶液中吸附40h，吸附达到平衡，吸附容量为7.5mg/g。     

界面上蜂窝状多孔薄膜的构建、性质和应用

综述了以Breath Figure(呼吸图案)法制备聚合物及纳米颗粒蜂窝状多孔结构的研究现状.当潮湿的气流吹到聚合物或纳米颗粒的有机溶液表面时,溶剂蒸发导致水微滴在液体表面冷凝重排成六角阵列结构.溶剂和水微滴蒸发完毕后,聚合物或纳米颗粒在基底上形成具有六角阵列的蜂窝状多孔结构.该技术是自组装领域的一大进展,在生物技术、组织工程、微图像技术、高端分离技术、光催化及医药等领域有望获得重要应用.本文系统阐述了规整蜂窝状孔结构材料的构建方法、构建材料、形成机理以及影响因素(包括湿度、浓度、气流方向和速度、溶剂、基底曲率等),评述了蜂窝状多孔薄膜的性质和应用,并对其在化学和材料科学领域的应用前景作了展望.     

新型聚芳醚腈酮超滤膜制备:非溶剂添加剂的影响

以含二氮杂萘酮结构的聚芳醚腈酮(PPENK)为膜材料、N-甲基吡咯烷酮(NMP)为溶剂,系统地研究了五种有机非溶剂添加剂(NSA)正丁醇(BuOH)、乙二醇(EgOH)、乙醚(Ether)、乙二醇甲醚(EGME)和聚乙二醇400(PEG-400)在以水作为凝胶剂时对平板超滤膜性能的影响。浊点法滴定了PPENK／NMP／NSA体系的相图;并以邻近比口值来表征铸膜液组成靠近相分离的程度。结果表明：以水为凝胶剂制备的超滤膜,在以BuOH、EgOH、EGME和PEp400为添加剂时,随着口值的增加,平均孔径和水通量增加,截留率降低,膜结构均从指状结构向海绵状结构转变;以Ether为添加剂时,结果相反。通过改变添加剂的种类和含量,制备了不同孔径大小和通量的PPENK超滤膜。     

聚砜酰胺超滤膜的制备和性能

本文研究了聚砜酰胺超滤膜制备的工艺条件和膜分离性能之间的关系。求得膜的分离性能随预压时间、蒸发时间、沉淀浴温度和溶剂种类而变化的规律。     

介体溶剂在碱金属PVC膜离子电极中选择性的研究

近年来,文献报道了几种 Li~+、Cs~+ 等离子交换剂 PVC 膜电极.这类电极对离子的选择性除同活性物质本身的性质有关,还与介体溶剂的性质有关系.本文考察了不同介体溶剂的四苯硼酸盐 PVC 膜对碱金属离子的选择性,探讨了不同介体溶剂的膜对选择性的影响.所得结果有助于研制性能良好的碱金属离子选择电极.     

钌催化β-酮酸酯不对称氢化反应的研究进展

钌催化β-酮酸酯不对称氢化反应是合成手性β-羟基酯的重要方法之一.综述了近十年来钌催化β-酮酸酯不对称氢化反应的研究进展,重点讨论了手性配体、底物结构、溶剂和添加剂等因素对均相不对称氢化反应的影响以及载体材料和助剂等因素对多相不对称氢化反应的影响.     

非对称双嵌段共聚物薄膜在平板受限和溶剂蒸发下自组装行为的分子模拟研究

采用模拟退火和Monte Carlo方法研究体相形成柱状相的双嵌段共聚物薄膜在平板受限和溶剂蒸发条件下的自组装,特别关注柱状相形貌的取向.对于平板受限下的薄膜,研究了表面选择性、溶剂选择性和膨胀程度对柱状相取向的影响.对于溶剂蒸发的薄膜,研究了表面选择性和薄膜厚度对柱状相取向的影响,并讨论了柱状相取向的机理.结果表明,薄膜内存在中性溶剂时形成垂直柱形貌的表面选择性范围较小;存在亲长嵌段的溶剂时形成垂直柱形貌的表面选择性范围较大.溶剂蒸发后薄膜生成垂直柱形貌的参数范围较热退火下增大;柱状相取向取决于蒸发过程中体系由球状相演化为柱状相时的薄膜厚度与体相周期的匹配性.     

高分子线性柔性链在超滤过程中第一类突变现象的观察

利用一种双层结构的膜屏蔽了每个微孔所产生的流场之间的相互作用,从而首次观测到理论上预计的高分子线性柔性链在超滤过程中的第一类突变现象,即仅当宏观流速高于一宏观阈值时,高分子长链方可通过尺寸远小于链无扰半径的微孔,且该宏观阈值与高分子链的长短无关.另外,实验中的过滤膜含有多个微孔,实验结果显示,当一给定的宏观流速低于宏观阈值时,部分微孔会被无法通过的较长的高分子链堵塞,造成未堵塞微孔中的微观流速大于微观阈值.因此,较短的高分子链可从未堵塞的微孔通过滤膜.     

PVDF亲水复合膜的制备及表征

聚偏氟乙烯(PVDF)膜材料存在强疏水性的缺陷,亲水化改性是解决该问题的主要途径。以PVDF为基膜材料、聚乙烯醇(PVA)为共混材料、N,N-二甲基乙酰胺(DMAc)为溶剂,采用相转化法制备PVDF/PVA复合膜。考察了复合膜的PVDF/PVA共混比、固含量、低分子化合物添加剂、聚合物添加剂等非溶剂添加剂对复合膜接触角的影响。结果表明,当PVDF/PVA共混比为7/3,固含量为13%时,制备的复合膜接触角为22.92°;当添加剂为无水氯化锂、纳米二氧化硅、聚乙烯吡咯烷酮(PVP)时,复合膜接触角分别从53.12°、30.51°和41.89°都降低到了0°,亲水性提高,其中纳米二氧化硅作为添加剂时复合膜亲水性最好;当添加剂为丙三醇、PMMA、PEG时,复合膜接触角都增大,亲水性变差。     

The effect of a polymeric additive on the evaporation of organic aerocolloidal droplets

 The evaporation of single triethyl phosphate (TEP) micro-droplets containing a high molecular weight polymer, poly(methyl methacrylate) (PMAA), was inves-tigated using an electrodynamic trap and light scattering measurements to explore the suppression of evaporation by the additive. Pure-component evaporation rates were measured to determine the vapor pressure over a range of temperatures, and the polymer was found to significantly decrease the evaporation rate. A numerical solution of the problem of simultaneous solvent evaporation and polymer diffusion within the droplet indicated a rapid build-up of PMMA at the surface of the drop, but vapor/liquid thermodynamic considerations alone do not account for the observed reduction in the evaporation rate for the droplets containing PMMA. After significant evaporation of TEP occurred, the ultra-low evaporation rate was measured using changes in the Raman spectra associated with morphology-dependent resonances. The evaporation in this regime appears to be controlled by the rate of solvent molecules diffusing through the polymer matrix. Received: 17 June 1997 Accepted: 24 October 1997     

酚酞基聚芳醚砜非对称超滤膜凝胶动力学研究

采用耐高温工程塑料——含酚酞侧基的聚芳醚砜(PES-C)为膜材料,草酸和聚乙二醇为添加剂,N,N-二甲基乙酰胺为溶剂,并利用改进的凝胶动力学实验装置和方法,使之能真实地再现不同膜孔结构生长及发展演化的过程,借助相关软件对图像进行处理,考察了添加剂、聚合物浓度对铸膜液凝胶速度的影响,对酚酞基聚芳醚砜非对称膜的凝胶过程的动力学进行研究.结果表明,动力学图像与最终膜结构有很好的一致性,凝胶动力学方面得到了与Strathman等不同的研究结果,发现凝胶前锋位移的平方与时间不是线性关系,凝胶动力学过程不能简单地用Fick扩散定律来描述.     

Preparation of porous polylactide microspheres by emulsion‐solvent evaporation based on solution induced phase separation

Porous polylactide (PLA) microspheres were fabricated by an emulsion‐solvent evaporation method based on solution induced phase separation. Scanning electron microscopy (SEM) observations confirmed the porous structure of the microspheres with good connectivity. The pore size was in the range of decade micrometers. Besides large cavities as similarly existed on non‐porous microspheres, small pores were found on surfaces of the porous microspheres. The apparent density of the porous microspheres was much smaller than that of non‐porous microspheres. Fabrication conditions such as stirring rate, good solvent/non‐solvent ratio, PLA concentration and dispersant (polyvinyl alcohol, PVA) concentration had an important influence on both the particle size and size distribution and the pore size within the microspheres. A larger pore size was achieved at a slower stirring rate, lower good solvent/non‐solvent ratio or lower PLA concentration due to longer coalescence time. Copyright © 2005 John Wiley & Sons, Ltd.     

Do additives shift the LCST of poly (<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) by solvent quality changes or by direct interactions?

The phase transition of thermoresponsive poly(N-isopropylacrylamide) is studied under the influence of additives considered as model substances for drugs. A series of aromatic compounds with similar structures, mainly benzaldehydes, is chosen. The lower critical solution temperature (LCST) is determined by differential scanning calorimetry and ¹H-NMR. All additives cause a down shift of the LCST, which depends on additive molecular structure and concentration. Since the LCST shifts are not correlated to hydrophobicity or solubility of the additive, the detailed substitution pattern is discussed as the controlling factor. The question whether LCST shifts can be explained by either the additives affecting the solvent quality or by specific interactions of additives with the polymer is addressed by LCST determination in dependence on polymer concentration. Though both factors are relevant, specific additive-polymer interactions are shown to play a major role in controlling the LCST.     

Polyurethane and sulfonated polysulfone blend ultrafiltration membranes. I. Preparation and characterization studies

Polyurethane (ether type) and sulfonated polysulfone (sodium salt form) in the presence of polyethylene glycol 600 were blended in various compositions using N,N'-dimethylformamide as solvent and used for preparing ultrafiltration membranes by the phase inversion technique. Polymer blend composition, additive concentration, and casting and gelation conditions were optimized. Blend membranes were subjected to ultrafiltration characterizations such as compaction, pure water flux, water content, and membrane resistance. The membranes were also subjected to the determination of pore statistics and molecular weight cutoff determination studies using dextran of different molecular weights. Surface morphology of the membranes was analyzed using scanning electron microscopy at different magnifications. The effects of polymer composition and additive concentration on the above parameters were analyzed and the results are compared and discussed with those of pure sulfonated polysulfone membranes. The derived pore size, porosity, and number of pores have a remarkable interrelationship and also have a definite role and relationship with the molecular weight cutoff, morphology, and flux performance of the membranes.     

聚乙二醇对聚醚砜微孔膜致孔作用的研究

以聚醚砜聚乙二醇溶剂为铸膜液体系、采用干湿相转化法制备微孔滤膜,研究了各种制膜条件对膜孔径结构的影响.实验发现聚乙二醇在体系中起到分散稳定的作用,只有到浓度大于70%时,才会对铸膜液的粘度产生明显影响,聚合物在铸膜液中的溶解状态也随之改变,进而影响膜的结构.不同溶剂NMP、DMF、DMAc、DMSO等极性溶剂或固体溶剂己内酰胺均可制得开孔率较高的微孔膜,但对膜的结构和性能影响差别不大.在本研究体系中,膜的结构取决于聚乙二醇、溶剂的浓度比例关系.     

Breath figure patterns prepared by spin coating in a dry environment

We introduce a novel method for fabricating breath figure patterns on a homopolymer film by spin coating of polymer solutions with various solvents. The homopolymers employed in this study were cellulose acetate butyrate, monocarboxylated end-functional polystyrene, and poly(methyl methacrylate). Breath figure patterns were generated even when a water-miscible solvent such as tetrahydrofuran (THF) was used as a solvent. We even succeeded in generating breath figure patterns by spin coating even under a dry environment (relative humidity less than 30%), when water was directly added into THF solution. With the combination of the spin coating method, pores with a few hundred nanometers to several micrometers have been generated. We found that the pore size becomes larger with increasing water content in THF solution and decreasing rotating speed. This is equivalent to increasing humidity and decreasing evaporation speed, respectively, in the conventional method, which is direct solvent evaporation under a humid environment. Thus, compared with the conventional method for making breath figure patterns, this method would be very convenient for fabricating large-scale films with various pore sizes.