五氧化二钒催化环己烯烯丙位氧化

 研究了以五氧化二钒为催化剂,以过氧化氢水溶液为氧源氧化环己烯. 考察了溶剂种类、溶剂用量、催化剂用量和反应温度等因素对催化剂性能的影响. 结果表明,常温下环己烯在此催化体系中主要发生烯丙位氧化反应生成环己烯酮. 溶剂的种类对催化活性和烯丙位酮式氧化的选择性具有较大的影响,丙酮是该反应的合适溶剂. 在丙酮与环己烯的体积比为4, 五氧化二钒与环己烯的质量比为1∶40, 过氧化氢与环己烯的摩尔比为3和反应温度为20 ℃的条件下,反应24 h后的环己烯转化率可达60%以上,环己烯酮选择性可达85%. 催化反应过程中丙酮可能与过氧化氢作用生成过氧化酮,从而进行氧转移,催化剂则经过V5+/V4+物种的循环使环己烯氧化成为环己烯酮等产物.     

甲基三氧化铼与双氮席夫碱原位配位及催化烯烃环氧化

以2-吡啶甲醛与苯胺及其衍生物缩合制备了3个双氮席夫碱配体,对其结构进行了表征.研究了席夫碱配体与甲基三氧化铼(MTO)在催化反应体系中的原位配位作用对MTO催化30%H2O2环氧化烯烃反应的影响.结果表明,含吸电子基羧基的双氮席夫碱配体(I)由于具有适宜的配位能力和酸性,在较低温度下与MTO配位可显著提高烯烃环氧化反应选择性,而反应速率没有明显降低.例如,以30%H2O2为氧化剂环氧化环己烯,当I与MTO的摩尔比为2,反应温度10℃时反应4 h,环己烯的转化率达到94.6%,环氧化物选择性高达99.0%.不具羧基的双氮席夫碱配体与MTO配位,尽管可以提高环氧化物的选择性,但同时却降低了MTO的催化活性.     

双氮席夫碱配体对甲基三氧化铼催化烯烃环氧化反应的影响

 利用 2-吡啶甲醛、6-甲基-2-吡啶甲醛或 6-异丙基-2-吡啶甲醛与对甲基苯胺缩合制得双氮席夫碱配体, 考察了席夫碱配体以及溶剂和温度对甲基三氧化铼 (MTO) 催化不同结构烯烃环氧化反应的影响. 结果表明, 这些席夫碱配体与 MTO 构成的催化剂体系在甲醇溶剂中的催化性能最好, 双氮配体能显著提高环氧化反应的选择性. 当以甲醇为溶剂, 环己烯为底物, 在 –10 oC 反应 12 h 时, 环己烯转化率和环氧化物选择性均可达 100%. 席夫碱的配位能力越强, 越有利于提高环氧化物选择性, 而其配位能力取决于吡啶环中 6-位取代基的电子和立体结构. 给电子能力较强和空间位阻较小的烷基对应的配体的配位能力较强.     

配体对固载型锰希夫碱催化剂的影响

以官能团化的MCM-41为载体,通过配位键键连法制备了6种不同配体的固载型锰希夫碱配合物,并使用FT-IR、XPS、N2吸附-脱附、DR-UV/vis、XRD和TGA-DTA等技术对其进行表征.将制得的催化剂用于环己烯的氧化反应,考察了催化剂催化分子氧氧化环己烯的反应性能,结果表明配体的类型对催化剂的活性和产物的选择性...     

离子液体对H2O2氧化环己烯制备反-1,2-环己二醇的催化作用

以H2O2为氧化剂,研究了离子液体为催化剂和溶剂,环己烯氧化生成反-1,2-环己二醇的反应。 考察了不同咪唑型离子液体、反应时间、反应温度和H2O2用量等对产率和选择性的影响, 实验结果表明,在7种咪唑型离子液体催化体系中,阳离子为咪唑环上含有1或2个羧基,阴离子为[PF6]的离子液体催化效果较好。 反应温度为100 ℃,n(H2O2)∶n(Cyclohexene)＝1.1∶1,反应5 h时,离子液体c（0.60 g,2.1 mmol）催化生成的反-1,2-环己二醇的产率和选择性分别为95%和97%,而离子液体f（0.20 g,0.6 mmol）催化生成的反-1,2-环己二醇的产率和选择性分别为84%和90%,从离子液体的用量来看,含2个羧基的离子液体f的催化效率更高。     

离子液体中V2O5催化环己烯选择氧化合成 2-环己烯酮

研究了以V2O5为催化剂,H2O2为氧化剂,在室温离子液体中环己烯氧化制备2-环己烯酮的反应.考察了离子液体种类、反应温度、催化剂用量和氧化剂用量等因素对2-环己烯酮产率的影响.结果表明,在H2O2用量为110 mmol,V2O5/环己烯摩尔比为2%,反应温度为313 K的条件下,在[bmim]BF4离子液体中反应10 h后,环己烯的转化率和2-环己烯酮选择性分别为88.7%和91.1%.对含离子液体的催化体系的重复使用性能进行了考察.结果发现,随着使用次数的增加,环己烯的转化率以及2-环己烯酮的选择性有所下降.     

二苯基膦胺配体的合成及其与铬(Ⅲ)化合物催化乙烯四聚的性能

 利用氯化二苯基膦与二胺类化合物反应生成二苯基膦胺配体, 它与四氢呋喃氯化铬或乙酰丙酮铬在甲基铝氧烷的存在下显示出较高的催化乙烯四聚的活性和较高的生成 1-辛烯选择性(最高可达73.1%). 产物除 1-辛烯外, 还包括 1-己烯、甲基环戊烷和亚甲基环戊烷. 实验结果表明, 铬化合物类型对催化剂活性和 1-辛烯选择性影响较小, 而反应温度、压力和Al/Cr摩尔比等对催化剂活性和1-辛烯选择性影响较大.     

锚链固定的多相化铑膦配合物氢甲酰化反应催化剂的制备及其催化性能

以溶胶-凝胶与锚链固定相结合的方法制备了新型多相化羰基铑膦配合物催化剂.利用FT-IR,XPS和ICP对催化剂进行了表征.考察了该催化剂对1-己烯氢甲酰化反应的催化性能,得到较佳的反应条件,即反应温度100℃、反应时间12h、催化剂用量为0.3382g(相当于金属铑含量为4.4×10-5mol)、反应压力5.0MPa.此时1-己烯的转化率为98.5%、醛的选择性92.4%、n/i比1.43.该催化剂循环使用7次仍具有较高的催化活性和选择性,表明该催化剂具有好的循环使用性能.XPS、ICP分析证明铑的部分流失主要是由于氢甲酰化反条件下CO取代膦配体所致.     

Ti-Beta分子筛的控制合成及高效催化环己烯环氧化

构建了以H₂O₂为氧化剂催化环己烯合成环氧环己烷的高效、 绿色催化反应体系. 在不加入铝源的情况下, 以四乙基氢氧化铵(TEAOH)为模板剂, 通过改进的干胶转化法控制H₂O/SiO₂摩尔比为1.5合成出Ti-Beta分子筛. 实验结果表明, 适宜的酸碱性、 含水量以及模板剂用量显著影响分子筛的结晶度, 同时影响晶粒尺寸和晶粒尺寸的均一性. 通过对Ti-Beta分子筛原粉进行焙烧处理制得Ti-Beta分子筛催化剂, 再通过对反应溶剂、 反应温度和反应时间的筛选和优化, 获得最优催化反应条件, 在该条件下, 环己烯转化率可达33.5%, 环氧环己烷选择性可达99.6%. 实验结果表明该催化剂是一种高效的多相催化剂.     

二乙醇胺作添加剂Ru-Zn催化剂上苯选择加氢制环己烯

采用共沉淀法制备了Ru-Zn催化剂,考察了二乙醇胺的添加对Ru-Zn催化剂上苯选择加氢制环己烯性能的影响,并采用N2物理吸附、透射电镜、X射线衍射、X射线荧光、傅里叶变换红外和程序升温还原等手段对催化剂进行了表征.结果表明,二乙醇胺可以与浆液中ZnSO4反应生成(Zn(OH)2)3(ZnSO4)(H2O)3和硫酸二乙醇胺盐.随着二乙醇胺用量的增加,化学吸附在催化剂表面的(Zn(OH)2)3(ZnSO4)(H2O)3增多,它与硫酸二乙醇胺盐的协同作用提高了Ru-Zn(4.9%)催化剂上苯选择加氢生成环己烯的选择性.当二乙醇胺用量为0.3g时,(Zn(OH)2)3(ZnSO4)(H2O)3在Ru-Zn(4.9%)催化剂加氢后样品的表面高度分散,反应性能最佳,循环使用第3次时苯转化率为84.3%,环己烯选择性和收率分别达75.5%和63.6%;使用至第4次时,反应25min时苯转化率和环己烯选择性仍可达75%以上,环己烯收率为58%以上.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.