（四甲基二硅撑）双（3—三甲硅基环戊二烯基）—四羰基二铁…

标题化合物（Ｍｅ２ＳｉＳｉＭｅ２）〔η＾５－（３－Ｍｅ３ＳｉＣ５Ｈ３）Ｆｅ（ＣＯ）２〕２／（μ－ＣＯ）２（Ａ）分子中的Ｆｅ－Ｆｅ键被钠汞齐还原断裂，生成相应的双铁负离子，分别与ＭｅＣＯＣｌ、ＰｈＣＯＣｌ、ＰｈＣＨ２Ｃｌ、ＣｌＣＨ２ＣＯＯＣ２Ｈ５和Ｐｈ３ＳｎＣｌ进行亲核取代反应，生成在铁原子上引入相应取代基的产物（Ｍｅ２ＳｉＳｉＭｅ２）〔η＾５－（３－Ｍｅ３ＳｉＣ５Ｈ３）Ｆｅ（ＣＯ）２Ｒ〕２（Ｒ：Ｍ     

新型高活性催化剂乙烯气相聚合的研究（Ⅵ）：锌化合物对催化…

研究了新型高活性乙烯气相聚合催化剂ＴｉＣｌ４、Ｔｉ（ＯＢｕ）４／ＭｇＣｌ２、ＳｉＯ２和ＺｎＣｌ２／醇／ＡｌＲ３体系中ＺｎＣｌ２－ＡｌＥｔ３／ＳｉＯ２重量比和锌化合物含量对气相均聚合的影响，比较了２种不同催化剂Ｃａｔ＃Ａ和Ｃａｔ＃Ｂ的聚合反应力学及性能差异。ｄ ｆ ｃｌｔｉｐ     

新型高活性催化剂乙烯气相聚合的研究（I）：气相均聚和共聚…

研究了新型高活性乙烯气相聚合催化剂ＴｉＣｌ４／ＭｇＣｌ２／ＺｎＣｌ２／ＳｉＣｌ４／醇／Ａｌ（ｉ－Ｂｕ）３体系中钛和醇组分含量对聚合反应和产物颗粒形态的影响。测定了乙烯气相聚合反应动力学曲线，确定了聚合动力学方程。用ＳＥＭ，ＤＳＣ，ＷＡＸＤ，＾１＾３ＣＮＭＲ对催化剂及聚合物的形态，结构和性能进行了分析和表征。     

Sm2O3对CuO-γ-Al2O3催化剂性能的影响

在色谱微反流动法实验装置上考察了负载Ｓｍ２Ｏ３对ＣｕＯγＡｌ２Ｏ３催化剂ＣＯ氧化活性的影响，并运用Ｘ射线衍射（ＸＲＤ）、程序升温还原（ＴＰＲ）及程序升温脱附（ＴＰＤＭＳ）技术研究了Ｓｍ２Ｏ３对ＣｕＯγＡｌ２Ｏ３催化剂的物相结构、氧化还原特性及表面氧的脱附与恢复行为的影响。结果表明，负载适量的Ｓｍ２Ｏ３对ＣｕＯγＡｌ２Ｏ３催化剂表面氧的脱出与恢复有促进作用，可使部分γＡｌ２Ｏ３相变成γＡｌ２Ｏ３和θＡｌ２Ｏ３的混合型。负载适量的Ｓｍ２Ｏ３能改善催化活性，而负载过量的Ｓｍ２Ｏ３则使ＣｕＯ催化剂上ＣｕＯ的晶粒增大，从而对催化活性起了抑制作用。     

铜（Ⅱ）－聚丙烯酰胺和铜（Ⅱ）－聚乙烯醇配位聚合物的配位数

配位聚合物ＰＡＡｍ－ＣｕＣｌ＿２和ｃｕＣｌ＿２·２Ｈ＿２Ｏ的Ｃｕ￣（２＋）２ｐＸＰＳ谱上都有Ｓｈａｋｅ－ｕｐ峰，其与各自的Ｃｕ￣（２＋）２ｐ３／２肩峰或主峰距离ΔＥｓ２或ΔＥｓ分别为８．７和８．６ｅＶ；但配位聚合物Ｃｕ（Ⅱ）－ＰＶＡ却无此峰．由此推定，前者的Ｃｕ￣（２＋）是以ｓｐ￣３杂化轨道接受ＰＡＡｍ４个链节单元Ｃ－Ｎ上Ｎ的孤对电子部分转移形成配位键；而Ｃｕ（Ⅱ）－ＰＶＡ配位聚合物中的Ｃｕ￣（２＋）却以ｄｓｐ￣２杂化轨道接受ＰＶＡ４个链节单元侧基Ｏ的孤对电子部分转移，产生配位键，即Ｃｕ￣（２＋）与ＰＡＡｍ或ＰＶＡ的链节单元配位比均是１：４，此结果与电导率法测定ＰＡＡｍ－ＣｕＣｌ＿２的配位比相同．     

聚醋酸乙烯酯与铜（Ⅱ）离子的配位反应及其催化作用

以ＥＳＲ、ＵＶ和ＩＲ表征Ｃｕ（２＋）离子与ＰＶＡＣ的配位反应。根据ＣＵＣｌ２·２Ｈ２Ｏ乙醇溶液与ＰＶＡｃ－ＣｕＣｌ２·２Ｈ２Ｏ乙醇溶液的电导率差值随Ｃｕ（２＋）离子摩尔浓度变化的明显转析点得知，１个Ｃｕ（２＋）离子大约能与ＰＶＡｃ４个链节单元配位。证实ＭＭＡ在Ｃｕ（Ⅱ）－ＰＶＡｃ配合物／Ｎａ２ＳＯ３体系的聚合体是无规ＰＭＭＡ，得率为７０％。讨论了ＭＭＡ在Ｃｕ（Ⅱ）－ＰＶＡｃ配合物／Ｎａ２ＳＯ３体系络合催化引发下的游离基反应历程。     

在涂层TiO2改性铜催化剂上甲醇脱氢制甲酸甲酯

在常压和２５０℃下，考察了涂层ＴｉＯ２改性铜催化剂上甲醇脱氢生成甲酸甲酯的活性和选择性以及催化剂的稳定性。结果表明，涂层ＴｉＯ２明显提高了铜催化剂的活性和稳定性。在所考察的铜催化剂中，以Ｃｕ／ＴｉＯ２／ＡｌＯ３的催化活性最高，甚至高于离子交换法制备的Ｃｕ（ｅｘ）／ＳｉＯ２催化剂。ＸＰＳ分析表明，Ｃｕ／ＴｉＯ２／ＡｌＯ３中存在着两种化学环境不同的ＣＵ（０），即负载在ｒ－ＡＬＯ３和ＴｉＯ２－Ａｌ２Ｏ３     

含氮聚硅氧烷配位体及其与金属离子的络合作用

研究ｎ－β（氨乙基）－γ（氨丙基）三乙氧基硅烷［ＮＨ２（ＣＨ２）２ＮＨ（ＣＨ２）３Ｓｉ（ＯＥｔ）３］与二甲基二乙氧基硅烷［（ＣＨ３）２Ｓｉ（ＯＥｔ）２］共水解，制备含－（ＣＨ２）３ＮＨ（ＣＨ２）２ＮＨ２功能基的聚硅氧烷配位体。用ＩＲ、１ＨＮＭＲ和元素分析法对共聚产物的结构进行了分析，同时用紫外－可见光谱法和ＳＥＭ考察了共聚产物与Ｃｕ２＋等金属离子的络合作用。结果发现，两种单体进行了共水解反应，而且随着ＮＨ２（ＣＨ２）２ＮＨ（ＣＨ２）３Ｓｉ（ＯＥｔ）３比例增加，水解程度提高。共聚产物可以与Ｃｕ２＋离子形成稳定的络合物，但不能与Ｚｎ２＋离子或Ａｌ３＋离子形成稳定的络合物或螯合物。     

（四甲基二硅撑）双（3－三甲硅基环戊二烯基）－四羰基二铁的反应性

标题化合物（Ｍｅ_２ＳｉＳｉＭｅ_２）［η￣５－（３－Ｍｅ_３ＳｉＣ_５Ｈ_３）Ｆｅ（ＣＯ）_２］_２／（μ－ＣＯ）_２（Ａ）分子中的Ｆｅ－Ｆｅ键被钠汞齐还原断裂，生成相应的双铁负离子，分别与ＭｅＣＯＣｌ、ＰｈＣＯＣｌ、ＰｈＣＨ_２Ｃｌ、ＣｌＣＨ_２ＣＯＯＣ_２Ｈ_５和Ｐｈ_３ＳｎＣｌ进行亲核取代反应，生成在铁原子上引入相应取代基的产物（Ｍｅ_２ＳｉＳｉＭｅ_２）［η￣５－（３－Ｍｅ_３ＳｉＣ_５Ｈ_３）Ｆｅ（ＣＯ）_２Ｒ］_２（Ｒ：ＭｅＣＯ（１），ＰｈＣＯ（２），ＰｈＣＨ_２（３），ＣＨ_２ＣＯＯＣ_２Ｈ_５（４），Ｐｈ_３Ｓｎ（５），Ｉ（６））。Ａ在氯仿中与碘反应，得到Ｆｅ－Ｆｅ断裂的双铁碘化物，但在苯中与过量碘反应，则得到Ｆｅ－Ｉ－Ｆｅ桥联的离子型化合物（Ｍｅ_２ＳｉＳｉＭｅ_２）［η￣５－（３－Ｍｅ_３ＳｉＣ_５Ｈ_３）Ｆｅ（ＣＯ）_２］_２Ｉ·Ｉ（７）。化合物６的晶体和分子结构经Ｘ射线衍射测定，６属单斜晶系，Ｐ２１／ｃ空间群，ａ＝１．７２１７（４）ｎｍ，ｂ＝０．７７５３（２）ｎｍ，Ｃ＝１．３６２９（７）ｎｍ，β＝１０３．８０（３）°，Ｖ＝１．７６７（２）ｎｍ３，Ｚ＝４，Ｄｃ＝１．６２９９·ｃｍ－１，最终偏差因子Ｒ＝０．０５４。     

链状三核异金属簇阴离子［Cl_2FeS_2M＇（PPh_3）_2］~－（M＝Mo

在５５０～９０ｃｍ~（－１）波数范围内，测量簇阴离子［Ｃｌ_２ＦｅＳ_２ＭＳ_２Ｍ′（ＰＰｈ_３）_２］~－（Ｍ＝Ｍｏ，Ｍ′＝Ａｇ；Ｍ＝Ｗ，Ｍ′＝Ｃｕ，Ａｇ）的付里叶变换红外光谱，并对标题簇阴离子［Ｃｌ_２ＦｅＳ_２ＷＳ_２Ｃｕ（ＰＰｈ_３）_２］~－，［Ｃｌ_２ＦｅＳ_２ＭｏＳ_２Ａｇ（ＰＰｈ_３）_２］~－和［Ｃｌ_２ＦｅＳ_２ＷＳ_２Ａｇ（ＰＰｈ_３）_２］~－骨架的振动光谱给予经验指认。同时采用＂诱导自洽方法计算振动力常数＂程序，对簇骨架［Ｃｌ_２ＦｅＳ_２ＭＳ_２Ｍ~′Ｐ_２］进行简正坐标分析。振动频率的计算值与观测值符合良好，两者平均偏差小于１．０％，计算结果支持了振动谱带的归属并表明计算力常数的合理性。文中还讨论了主要价键振动频率的变化规律。     

Interfacial reactions of duplex stainless steels with molten aluminum

The morphology and constitution of the intermetallic layers formed on the surface of duplex stainless steels (DSSs) immersed in molten aluminum at 750 °C for 30 min have been studied in detail by scanning electron microscopy and electron probe micro‐analyzer. Compared with H13 steel, the DSSs exhibited a better corrosion resistance. The weight loss rates, as expressed in terms of weight loss per square centimeter of the specimen per minute, of DSSs are smaller than that of H13. The thickness of the intermetallic layers of DSSs is comparatively thinner. And the interface between the intermetallic layers and DSSs substrate is much flatter. The intermetallic layers of duplex stainless steels are consisted of inner continuous (Fe,Cr)₂Al₅ phase and outer porous (Fe,Cr)Al₃ phases. Microstructure observations suggest that the retarded interfacial reaction between DSSs and molten aluminum is associated with a continuous Al‐Fe‐Cr intermetallic phases layer formed on the solid/liquid interface, which acts as an effective diffusion barrier. The precipitation phase particles distributed along the austenite/ferrite and ferrite/ferrite interfaces also had a good effect on the corrosion resistance properties of DSSs to molten aluminum. Copyright © 2015 John Wiley & Sons, Ltd.     

Site-specific specimen preparation by focused ion beam milling for transmission electron microscopy of metal matrix composites.

This work describes the application and usefulness of the focused ion beam (FIB) technique for the preparation of transmission electron microscopy (TEM) samples from metal matrix composite materials. Results on an Aldiamond composite, manufactured by the squeeze casting infiltration process, were chosen for demonstration. It is almost impossible to prepare TEM specimens of this material by any other conventional method owing to the presence of highly inhomogeneous phases and reinforcement diamond particles. The present article gives a detailed account of the salient features of the FIB technique and its operation. One of the big advantages is the possibility to prepare site-specific TEM specimens with high spatial resolution. The artifacts occurring during the specimen preparation, for example, Ga-ion implantation, curtain effects, amorphous layers, bending of the lamella, or different milling behaviors of the materials have been discussed. Furthermore, TEM examination of the specimens prepared revealed an ultrafine amorphous layer of graphite formed at the interface between the Al and diamond particles that may affect the interfacial properties of the composite materials. This may not have been feasible without the successful application of the FIB technique for production of good quality site-specific TEM specimens.     

Interface analysis in metal matrix composites

Summary Using surface and microanalytical methods (Auger electron spectroscopy, X-ray photoelectron spectroscopy and analytical electron microscopy) the interface in the SiC fiber reinforced Ti6A14V alloy and in the Al₂O₃ fiber reinforced Al12SiCuMgNi alloy was investigated. The analytical methods can be used for an understanding of the interface reaction process taking place during composite processing and allow a judgment on the effectiveness of fiber coating in composites.

---

Grenzflächenanalyse an Faserverbundwerkstoffen mit metallischer Matrix

     

铝基板的界面扩散对薄膜型TiO2光催化活性的影响

以钛酸四丁酯为前驱体, 采用溶胶-凝胶法在铝基板表面制备了纳米晶TiO2薄膜. 运用XRD、SEM和XPS对制得的薄膜进行表征, 并测试了薄膜光催化降解亚甲基蓝(MB)的活性. 结果表明, TiO2薄膜样品在450 ℃焙烧30 min后, 晶粒排列比较致密, 粒径为10-20 nm, 并与铝基板紧密结合; 薄膜与铝基板发生了明显的界面扩散, 薄膜中的Al元素来自铝基板的界面扩散, 且界面层很宽, 扩散层厚度约为75 nm; 界面扩散的发生直接导致了TiO2薄膜的光催化活性下降. 但随着薄膜厚度增加, 铝基板对TiO2薄膜降解亚甲基蓝催化活性的影响不断减小.     

Analytical electron microscopy studies of lithium aluminum hydrides with Ti- and V-based additives

The microstructure of LiAlD(4) with TiCl(3).1/3(AlCl(3)) and VCl(3) additives has been studied during different steps of the decomposition process using electron energy loss spectroscopy and energy-dispersive X-ray spectroscopy in a scanning transmission electron microscope. Energy filtered transmission electron microscopy was used to show elemental distributions in the samples. The spatial distribution of the additives and the main elements within the alanate particles was examined with a resolution of a few nanometers. The analysis of the electron energy loss spectra reveals the chemical state of Al, O, and the additives. Ti and V do not appear to mix chemically with Al to a significant degree. V was found in high concentration in just a few particles, while Ti is more uniformly distributed. All the samples showed evidence of oxidation despite procedures being adopted to avoid exposing the material to air. The additives are oxidized in all the samples, and Al(2)O(3) forms a thin layer at the surface of the particles. This paper gives a comparison between samples at different stages of the decomposition process using different additives.     

Characterization of SiC-platelets

Three fractions of SiC platelets were characterized using polarizing microscopy, X-ray diffraction, high resolution Auger electron spectroscopy (AES), electron spectroscopy for chemical analysis (ESCA) and scanning electron microscopy with energy dispersive analysis (SEM/EDX). The chemical analysis of the three fractions is given. The determination of the SiC polytypes (4H, 6H, 15R, 3C) was done and has been correlated with the chemical analysis. The results of the X-ray diffraction investigations confirm the polarizing microscopy observations. Using microanalytical techniques important conclusions about the impurity elements (e.g. B, Al, Fe) and their local distribution could be drawn. Most of them were found to be present on the outermost surfaces of the platelets. Some conclusions concerning the processing of the platelets are suggested.Dedicated to Professor Günther Tölg on the occasion of his 60th birthday     

Adsorption of PBTCA on Alumina Surfaces and Its Influence on the Fractal Characteristics of Sediments

The adsorption of 2-phosphonobutane-1,2,4-tricarboxylic acid (PBTCA) on Al(2)O(3) powder has been studied as a function of pH and concentration. The adsorption density of PBTCA is found to decrease with an increase of pH. Zeta potential measurements show that the addition of PBTCA results in a dramatic increase in the absolute zeta potential, as well as a shift of the isoelectric point to the more acidic region. PBTCA considerably enhances the stability of the alumina suspension via an electrostatic mechanism. The surface properties of alumina suspensions are examined by using Auger electron microscopy and FTIR analysis. Chemical interactions take place at the solid/water interface by forming complexes between Al(3+) ions and PBTCA. The dispersing ability of PBTCA is believed to be related to its high adsorption ability and the high number of dissociable protons. The morphology of the sediments is observed with scanning electron microscopy. It is found that the sediment surfaces exhibit fractal characteristics. The fractal dimension values of sediments are correlated with PBTCA concentration in the experimental range. Copyright 2000 Academic Press.     

Beyond the structure-property relationship paradigm: influence of the crystal structure and microstructure on the Li+ conductivity of La2/3Li(x)Ti(1-x)Al(x)O3 Oxides

The crystal structures of several oxides of the La(2/3)Li(x)Ti(1-x)Al(x)O(3) system have been studied by selected-area electron diffraction, high-resolution transmission electron microscopy, and powder neutron diffraction, and their lithium conductivity has been by complex impedance spectroscopy. The compounds have a perovskite-related structure with a unit cell radical2 a(p)x2 a(p)x radical2 a(p) (a(p)=perovskite lattice parameter) due to the tilting of the (Ti/Al)O(6) octahedra and the ordering of lanthanum and lithium ions and vacancies along the 2 a(p) axis. The Li(+) ions present a distorted square-planar coordination and are located in interstitial positions of the structure, which could explain the very high ionic conductivity of this type of material. The lithium conductivity depends on the oxide composition and its crystal microstructure, which varies with the thermal treatment of the sample. The microstructure of these titanates is complex due to formation of domains of ordering and other defects such as strains and compositional fluctuations.     

Theoretical prediction of impurity effects on the internally oxidized metal/oxide interface: the case study of S on Cu/Al2O3

A detrimental sulfur effect on adhesion is known for iron- and nickel-oxide interfaces, but has never been reported on copper-oxide interfaces. Here we present a first-principles based study on the effects of temperature, interfacial stoichiometry, Al activity, and S segregation on the internally oxidized Cu/α-Al(2)O(3) interface. The calculated "interfacial phase diagram" for temperatures of interest suggests that the equilibrium interface structure is near the transition between Al-rich and stoichiometric phases. The Al-rich type interface is significantly stronger than the stoichiometric counterpart. The S effect on the Cu/α-Al(2)O(3) interface is obvious: S strongly segregates to both types of interface, degrades the adhesion (by ～65%) and also reduces the size stability of alumina particles in Cu.     

SiCp/ Al复合材料与化学镀镍层结合机理研究

根据结构化学理论，用SEM, EDAX和XPS等测试手段研究了镀层和碳化硅颗粒增强铝基复合材料(SiC_p/ Al)的表面、断面形貌及界面的结合状态，分析了镀层和基体之间的结合机理。结果表明，Ni镀层与复合材料界面有良好的结合，在复合材料表面的SiC-Al界面，初期沉积物Ni按Al的晶格外延生长出现微晶层，然后吸附原子扩散迁移、碰撞结合并与界面上的SiC晶格匹配生长，在镍层中诱发了拉伸应力。镍晶格和基体粒子之间产生了键合作用，形成的键显示出共价键和离子键的混合性质。