Thermal behavior of loratadine

Simultaneous thermogravimetry (TG) and differential thermal analysis (DTA) techniques were used for the characterization the thermal degradation of loratadine, ethyl-4-(8-chloro-5,6-dihydro-11H-benzo[5,6]cyclohepta[1,2-b]pyridin-11-ylidine)-1-piperidinecarboxylate. TG analysis revealed that the thermal decomposition occurs in one step in the 200–400°C range in nitrogen atmosphere. DTA and DSC curves showed that loratadine melts before the decomposition and the decomposition products are volatile in nitrogen. In air the decomposition follows very similar profile up to 300°C, but two exothermic events are observed in the 170–680°C temperature range. Flynn–Wall–Ozawa method was used for the solid-state kinetic analysis of loratadine thermal decomposition. The calculated activation energy (E _a) was 91±1 kJ mol^–1 for α between 0.02 and 0.2, where the mass loss is mainly due to the decomposition than to the evaporation of the decomposition products.     

Kinetic investigation on thermal decomposition of organophosphorous compounds

In this paper, the thermal behaviours of two organophosphorous compounds, N,N-dimethyl-N′,N′-diphenylphosphorodihydrazidic (NDD) and diphenyl amidophosphate (DPA), were studied by thermogravimetery (TG), differential thermal analysis (DTA) and differential scanning calorimetery (DSC) techniques under non-isothermal conditions. The results showed that NDD melts about 185 °C before it decomposes. NDD decomposition occurs in two continuous steps, in the 190–410 °C temperature range. First thermal degradation stage for NDD results a broad exothermic peak in the DTA curve that is continued with a small exothermic peak at the end of decomposition process. On the other hand, applying TG-DTA techniques indicates that DPA melts about 150 °C before it decomposes. This compound decomposes in the temperature range of 230 to 330 °C in two steps. These steps are endothermic and exothermic, respectively. Activation energy and pre-exponential factor for the first step of decomposition of each compound were found by means of Kissinger method and were verified by Ozawa–Flynn–Wall method. Activation energy obtained by Kissinger method for the first stage of NDD and DPA decompositions are 138 and 170 KJ mol⁻¹, respectively. Finally, the thermodynamic parameters (ΔG ^#, ΔH ^# and ΔS ^#) for first step decomposition of investigated organophosphorous were determined.     

Thermal behavior of drugs

Data on the thermal stability of drugs was required to obtain information for handling, storage, shelf life and usage. In this study, the thermal stability of two nonsteroidal anti-inflammatory drugs (NSAIDs) was determined by differential scanning calorimetry (DSC) and simultaneous thermogravimetery/differential thermal analysis (TG/DTA) techniques. The results of TG analysis revealed that the main thermal degradation for the naproxen and celecoxib occurs in the temperature ranges of 196–300 and 245–359 °C, respectively. The TG/DTA analysis of compounds indicates that naproxen melts (at about 158.1 °C) before it decomposes. However, the thermal decomposition of the celecoxib started about 185 °C after its melting. The influence of the heating rate (5, 10, 15, and 20 °C min⁻¹) on the DSC behavior of the both drug samples was verified. The results showed that, as the heating rate was increased, decomposition temperatures of the compounds were increased. Also, the kinetic parameters such as activation energy and frequency factor for the compounds were obtained from the DSC data by non-isothermal methods proposed by ASTM E696 and Ozawa. Based on the values of activation energy obtained by various methods, the following order for the thermal stability was noticed: naproxen > celecoxib. Finally, the values of ΔS ^#, ΔH ^#, and ΔG ^# of their decomposition reaction were calculated.     

Preparation and reactivity of metal-containing monomers

The thermal decomposition of iron (III) acrylate, [Fe₃O(CH₂=CHCOO)₆ · 3H₂O]OH (FeAcr), a monomer with a complex cluster cation, has been studied at 200–370 °C. Thermal transformations of FeAcr occur in two temperature regions. The rates of gas evolution in the low temperature region (200–300 °C) and the high temperature region (300–370 °C) are described by first-order equations withk=4.2 · 10²¹exp[−59000/(RT)] s⁻¹ andk=1.3 · 10⁶exp[−30500/(RT)] s⁻¹, respectively. A study of the qualitative and quantitative composition of the products of FeAcr thermolysis was carried out. The thermal transformation of FeAcr is a complex process of dehydration, degradation, and polymerization in the solid phase followed by decarboxylation of the metal-carboxyl groups of the polymer. for part 33 see Ref. 1. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 1743–1750, October, 1993.     

Non-isothermal Studies on Mechanism And Kinetics of Thermal Decomposition of Cobalt(II) Oxalate Dihydrate

Thermal decomposition of CoC₂O₄⋅2H₂O was studied using DTA, TG, QMS and XRD techniques. It was shown that decomposition generally occurs in two steps: dehydration to anhydrous oxalate and next decomposition to Co and to CoO in two parallel reactions. Two parallel reactions were distinguished using mass spectra data of gaseous products of decomposition. Both reactions run according toAvrami–Erofeev equation. For reaction going to metallic cobalt parameter n=2 and activation energy is 97±14 kJ mol^–1. It was found that decomposition to CoO proceeds in two stages. First stage (0.12<α_II<0.41) proceeds according to n=2, with activation energy 251±15 kJ mol^–1 and second stage (0.45<α_II<0.85) proceeds according to parameter n=1 and activation energy 203±21 kJ mol^–1. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermal degradation of poly(lactic acid) measured by thermogravimetry coupled to Fourier transform infrared spectroscopy

Thermogravimetric (TG), differential thermal analysis (DTA) and thermal degradation kinetics, FTIR and X-ray diffraction (XRD) analysis of synthesized glycine–montmorillonite (Gly–MMT) and montmorillonite bound dipeptide (Gly–Gly–MMT) along with pure Na–MMT samples have been performed. TG analysis at the temperature range 25–250 °C showed a mass loss for pure Na–MMT, Gly–MMT and Gly–Gly–MMT of about 8.0%, 4.0% and 2.0%, respectively. DTA curves show the endothermic reaction at 136, 211 and 678 °C in pure Na–MMT whereas Gly–MMT shows the exothermic reaction at 322 and 404 °C and that of Gly–Gly–MMT at 371 °C. The activation energies of the first order thermal degradation reaction were found to be 1.64 and 9.78 kJ mol⁻¹ for Gly–MMT and Gly–Gly–MMT, respectively. FTIR analyses indicate that the intercalated compounds decomposed at the temperature more than 250 °C in Gly–MMT and at 250 °C in Gly–Gly–MMT.     

Study on thermal decomposition of copper(II) acetate monohydrate in air

The thermal decomposition of copper(II) acetate monohydrate (CuAc₂·H₂O) under 500 °C in air was studied by TG/DTG, DTA, in situ FTIR and XRD experiments. The experimental results showed that the thermal decomposition of CuAc₂·H₂O under 500 °C in air included three main steps. CuAc₂·H₂O was dehydrated under 168 °C; CuAc₂ decomposed to initial solid products and volatile products at 168–302 °C; the initial solid products Cu and Cu₂O were oxidized to CuO in air at 302–500 °C. The copper acetate peroxides were found to form between 100 and 150 °C, and the dehydration of these peroxides resulted in the presence of CuAc₂·H₂O above 168 °C. The initial solid products were found to be the admixture of Cu, Cu₂O, and CuO, not simply the single Cu₂O as reported before. Detailed reactions involved in these three steps were proposed to describe the complete mechanism and course of the thermal decomposition of CuAc₂·H₂O in air.     

Mechanism of formation of nanosized copper particles in a nanoreactor based on the [LiAl<Subscript>2</Subscript>(OH)<Subscript>6</Subscript>]<Subscript>2</Subscript>[Cuedta]·<Emphasis Type="Italic">n</Emphasis>H<Subscript>2</Subscript>O supramolecular system

The formation of nanosized copper particles in a nanoreactor based on the [LiAl₂(OH)₆]₂[Cuedta]·nH₂O supramolecular system [Li-Al-Cu(edta)] was studied by the DTA, XRPA, FMR, IR, and mass spectrometry methods. Thermal decomposition of Li-Al-Cu(edta) below 200°C occurs as two-stage removal of the interlayer water molecules. Above 200°C dehydration of [LiAl₂(OH)₆]⁺ metal hydroxide layers occurs simultaneously with destruction of [Cuedta]^2? complexonate ions. The first stage of destruction (below 250–260°C) is a redox process that forms metallic copper and liberates gaseous carbon oxide and dioxide. At higher thermolysis temperatures, other gaseous products evolve (ammonia, hydrogen). The copper phase appeared during thermal decomposition as 20–50 nm isometric particles on the surface, while lenslike copper nanoparticles formed in the bulk substance.     

Thermal analysis study of imidazolinium and some benzimid azolium salts by TG

The imidazolinium and benzimidazolium bromide salts with pentafluor substituents on N atom were synthesized. The structures of imidazolinium and benzimidazolium bromide salts obtained were conformed by ¹H and ¹³C NMR, ¹⁹F NMR and elemental analysis. It was found that pyrolytic decomposition occurs with melting in salts. The imidazolinium and benzimidazolium bromide salts were studied by TG-DTG and DTA from ambient temperature to 1000°C in nitrogen atmosphere. The decomposition occurred mainly in one stage and the values of activation energy E, frequency factor A, reaction order n, enthalpy change ΔH ^#, entropy change ΔS ^# and Gibbs free energy ΔG ^#, of the thermal decomposition were calculated by means of Coats-Redfern (CR), MacCallum-Tanner (MC) and van Krevelen (vK) methods. The activation energy value obtained by CR and MC methods were in good agreement with each other while those obtained by vK were found to be 10–12 kJ mol⁻¹ larger.     

Thermal behaviour of cephalexin in different mixtures

The thermoanalytical curves (TA), i.e. TG, DTG and DTA for pure cephalexin and its mixtures with talc, magnesium stearate, starch and microcrystalline cellulose, respectively, were drawn up in air and nitrogen at a heating rate of 10 °C min⁻¹. The thermal degradation was discussed on the basis of EGA data obtained for a heating rate of 20 °C min⁻¹. Until 250 °C, the TA curves are similar for all mixtures, up this some peculiarities depending on the additive appears. These certify that between the pure cephalosporin and the excipients do not exists any interaction until 250 °C. A kinetic analysis was performed using the TG/DTG data in air for the first step of cephalexin decomposition at four heating rates: 5, 7, 10 and 12 °C min⁻¹. The data processing strategy was based on a differential method (Friedman), an integral method (Flynn–Wall–Ozawa) and a nonparametric kinetic method (NPK). This last one allowed an intrinsic separation of the temperature, respective conversion dependence on the reaction rate and less speculative discussions on the kinetic model. All there methods had furnished very near values of the activation energy, this being an argument for a single thermooxidative degradation at the beginning (192–200 °C).     

Thermal, spectral and AFM studies of calcium silicate hydrate-polymer nanocomposite material

A non-ionic polymer (poly(vinyl alcohol) (PVA)) has been incorporated into the inorganic layers of calcium silicate hydrate (C–S–H) during precipitation of quasicrystalline C–S–H from aqueous solution. C–S–H and a C–S–H-polymer nanocomposite (C–S–HPN) material were synthesized and characterized by X-ray fluorescence (XRF), energy dispersive spectroscopy (EDS), ²⁹Si magic angle spinning nuclear magnetic resonance (²⁹Si MAS NMR) and ¹³C cross-polarization nuclear magnetic resonance (¹³C CP NMR) spectroscopy, atomic force microscopy (AFM), thermal conductivity, thermogravimetric analysis (TG) and differential thermal analysis (DTA). Thermal conductivity of PVA, C–S–H and C–S–HPN material was studied in the temperature range 25–50°C. C–S–HPN materials exhibited the highest thermal conductivity at 25 and 50°C. The thermal conductivity increases from 25 to 50°C are 7.03, 17.46 and 14.85% for PVA, C–S–H and C–S–HPN material, respectively. Three significant decomposition temperature ranges were observed on the TG curve of C–S–HPN material.     

Thermal decomposition of solid state poly(β-L-malic acid)

Thermal decomposition process of solid state poly(β -L-malic acid) was traced by DSC combined with FT-IR. Melting temperature of this partially crystallized polymer was detected at 46-60°C. The thermal decomposition initiated at ca 185°C accompanied by an evolution of gaseous products. In contrast to the cleavage reaction in the aqueous polymer solutions which gives L-malic acid and corresponding dimer of L-malic acid, the solid state poly(β -L-malic acid) decomposed at above the decomposition temperature giving not the constituent L-malic acid but fumaric acid at the first stage of the reaction then, maleic and maleic anhydride. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermal behaviour of lignins extracted from different raw materials

The thermal degradation of lignins extracted from bagasse, rice straw, corn stalk and cotton stalk, have been investigated using the techniques of thermogravimetric analysis (TG) and differential thermal analysis (DTA), between room temperature and 600°C. The actual pyrolysis of all samples starts above 200°C and is slow. The results calculated from TG curves indicated that the activation energy, Efor thermal degradation for different lignins lies in the range 7.949–8.087 kJ mol^?1. The DTA of all studied lignins showed an endothermic tendency around 100°C. In the active pyrolysis temperature range, thermal degradation occurred via two exothermic process at about 320 and 480°C, and a large endothermic pyrolysis region between 375 and 450°C. The first exothermic peak represents the main oxidation and decomposition reaction, the endothermic effect represents completion of the decomposition and the final exothermic peak represents charring.     

Characterization and preparation of nanocrystalline MgCuZn ferrite powders synthesized by sol–gel auto-combustion method

Nanocrystalline Mg–Cu–Zn ferrite powders were successfully synthesized through nitrate–citrate gel auto-combustion method. Characterization of the nitrate–citrate gel, as-burnt powder and calcined powders at different calcination conditions were investigated by using XRD, DTA/TG, IR spectra, EDX, VSM, SEM and TEM techniques. IR spectra and DTA/TGA studies revealed that the combustion process is an oxidation–reduction reaction in which the NO₃ ⁻ ion is oxidant and the carboxyl group is reductant. The results of XRD show that the decomposition of the gel indicated a gradual transition from an amorphous material to a crystalline phase. In addition, increasing the calcination temperature resulted in increasing the crystallite size of Mg–Cu–Zn ferrite powders. VSM measurement also indicated that the maximum saturation magnetization (64.1 emu/g) appears for sample calcined at 800 °C while there is not much further increase in M _s at higher calcination temperature. The value of coercivity field (H _c) presents a maximum value of 182.7 Oe at calcination temperature 700 °C. TEM micrograph of the sample calcined at 800 °C showed spherical nanocrystalline ferrite powders with mean size of 36 nm. The toroidal sample sintered at 900 °C for 4 h presents the initial permeability (μ _i) of 405 at 1 MHz and electrical resistivity (ρ) of 1.02 × 10⁸ Ω cm.     

A thermal analysis calculation of pharmaceutical wastewater sludge

Thermal pyrolysis of pharmaceutical wastewater sludge, brown coal, and sludge-coal blends were studied by TG dynamic runs carried out at 20 °C min⁻¹ in the temperature range from 25 to 850 °C. Different possible kinetic models of thermal decomposition have been considered. The best models of mechanism function for brown coal, pharmaceutical wastewater sludge, and coal–sludge blends are a first-order reaction, a N-dimensional nucleation, and growth reactions with N = 2 and 4, respectively. The Arrhenius kinetic parameters for brown coal, pharmaceutical wastewater sludge, and coal–sludge blends are proposed.     

Thermal decomposition of methylxanthines

The thermal decomposition of theophylline, theobromine, caffeine, diprophylline and aminophylline were evaluated by calorimetrical, thermoanalytical and computational methods. Calorimetrical studies have been performed with aid of a heat flux Mettler Toledo DSC system. 10 mg samples were encapsulated in a 40 μL flat-bottomed aluminium pans. Measurements in the temperature range form 20 to 400°C were carried out at a heating rate of 10 and 20°C min⁻¹ under an air stream. It has been established that the values of melting points, heat of transitions and enthalpy for methylxanthines under study varied with the increasing of heating rate. Thermoanalytical studies have been followed by using of a derivatograph. 50, 100 and 200 mg samples of the studied compounds were heated in a static air atmosphere at a heating rate of 3, 5, 10 and 15°C min⁻¹ up to the final temperature of 800°C. By DTA, TG and DTG methods the influence of heating rate and sample size on thermal destruction of the studied methylxanthines has been determined. For chemometric evaluation of thermoanalytical results the principal component analysis (PCA) was applied. This method revealed that first of all the heating rate influences on the results of thermal decomposition. The most advantageous results can be obtained taking into account sample masses and heating rates located in the central part of the two-dimensional PCA graph. As a result, similar data could be obtained for 100 mg samples heated at 10°C·min⁻¹ and for 200 mg samples heated at 5°C min⁻¹.     

Evolved gas analysis at thermal treatment of some solid fossil fuels

Coupled TG-FTIR technique was used for identification of gaseous compounds evolved at thermal treatment of six coal samples from different deposits (Bulgaria, Russia, Ukraine). The experiments were carried out under dynamic heating conditions up to 900°C at heating rates of 5, 10 or 50 K min^–1 in a stream of dry air. The emission of CO₂, H₂O, CO, SO₂, COS, methane, methanol, formic acid, formaldehyde, acetaldehyde, chlorobenzene was clearly identified in FTIR spectra of the samples studied. The formation of ethanol, ethane, ethylene and p-xylene, at least on the level of traces, was also identified. At the heating rate of 5°C min^–1 the temperature of maximum intensities of the characteristic peaks of COS was 270°C, of formaldehyde, formic acid, ethane and methanol 330°C, of SO₂, CO, acetic acid, ethylene and p-xylene 400°C and of chlorobenzene 500°C. At 10°C min^–1 and 50°C min^–1 these temperatures were shifted, respectively, by 70–300°C and 150–450°C towards higher temperatures and the respective absorption bands in FTIR spectra were, as a rule, more intensive.     

Regularities of self-propagating high-temperature synthesis in the solid 8-hydroxyquinoline—chloramine B system

The regularities of chemical reactions in solid 8-hydroxyquinoline—chloramine B mixtures were studied under conditions of organic self-propagating high-temperature synthesis (SHS), isothermal reaction, and thermal explosion in the 20–220 °C temperature range. Comprehensive physicochemical analysis and microstructural study of the reaction products were carried out. The temperature of SHS initiation (58 °C), the heat of the reaction (129±9 kJ mol⁻¹), the stoichiometric coefficient (1), the maximum temperature (T _max=98–140 °C), and the velocity of SHS wave propagation (u=0.15–0.55 mm s⁻¹) were determined. Depending on the ratio of the reactants (n), a low-temperature non-degeerate stable gasless mode (n≤1,T _max=115 °C,E _a=42 kcal mol⁻¹) and a high-temperature mode (n>1,T _max=140 °C,E _a=0.4 kcal mol⁻¹) are possible for SHS. The SHS affords monohydroxy and monochloro derivatives of 8-hydroxyquinoline, benzenesulfonamide, NaCl, NaOH, and H₂O. The mechanism of the solid-phase reaction at temperatures below 58 °C includes surface, solid-phase, and gas-phase diffusion; that for SHS is capillary spreading of the hydroxyquinoline melt. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 12, pp. 2271–2284, December, 1999.     

Formation of Cr(II) Species in the H2/CrO3 System. Parameter control

The thermal behaviour of CrO₃ on heating up to 600°C in dynamic atmospheres of air, N₂ and H₂ was examined by thermogravimetry (TG), differential thermal analysis (DTA), IR spectroscopy and diffuse reflectance spectroscopy (DRS). The results revealed three major thermal events, depending to different extents on the surrounding atmosphere: (i) melting of CrO₃ near 215°C (independent of the atmosphere), (ii) decomposition into Cr₂(CrO₄)₃ at 340–360°C (insignificantly dependent), and (iii) decomposition of the chromate into Cr₂O₃ at 415–490°C (significantly dependent). The decomposition CrO₃ → Cr₂(CrO₄)₃ is largely thermal and involves exothermic deoxygenation and polymerization reactions, whereas the decomposition Cr₂(CrO₄)₃ → Cr₂O₃ involves endothermic reductive deoxygenation reactions in air (or N₂) which are greatly accelerated and rendered exothermic in the presence of H₂. TG measurements as a function of heating rate (2–50°C min⁻¹) demonstrated the acceleratory role of H₂, which extended to the formation of Cr(II) species. This could sustain a mechanism whereby H₂ molecules are considered to chemisorb dissociatively, and then spillover to induce the reduction. DTA measurements as a function of the heating rate (2–50°C min⁻¹) helped in the derivation of non-isothermal kinetic parameters strongly supportive of the mechanism envisaged. This revised version was published online in August 2006 with corrections to the Cover Date.     

The non-isothermal decomposition of cobalt acetate tetrahydrate

The non-isothermal decomposition of cobalt acetate tetrahydrate was studied up to 500°C by means of TG, DTG, DTA and DSC techniques in different atmospheres of N₂, H₂ and in air. The complete course of the decomposition is described on the basis of six thermal events. Two intermediate compounds (i.e. acetyl cobalt acetate and cobalt acetate hydroxide) were found to participate in the decomposition reaction. IR spectroscopy, mass spectrometry and X-ray diffraction analysis were used to identify the solid products of calcination at different temperatures and in different atmospheres. CoO was identified as the final solid product in N₂, and Co₃O₄ was produced in air. A hydrogen atmosphere, on the other hand, produces cobalt metal. Scanning electron microscopy was used to investigate the solid decomposition products at different stages of the reaction. Identification of the volatile gaseous products (in nitrogen and in oxygen) was performed using gas chromatography. The main products were: acetone, acetic acid, CO₂ and acetaldehyde. The proportions of these products varied with the decomposition temperature and the prevailing atmosphere. Kinetic parameters (e.g.E and lnA) together with thermodynamic functions (e.g. °H, C _p and °S) were calculated for the different decomposition steps. In celebration of the 60^th birthday of Dr. Andrew K. Galwey