Generator‐collector Voltammetry at Dual‐plate Gold‐gold Microtrench Electrodes as Diagnostic Tool in Ionic Liquids

Ionic liquids provide high viscosity solvent environments with interesting voltammetric characteristics and new electrochemical mechanisms. Here, a gold‐gold dual‐plate microtrench electrode is employed in generator‐collector mode to enhance viscosity‐limited currents in ionic liquids due to fast feedback within small inter‐electrode gaps (5 μm inter‐electrode gap, 27 μm microtrench depth) and to provide a mechanistic diagnosis tool. Three redox systems in the ionic liquid BMIm⁺BF₄^? are investigated: (i) ferrocene oxidation, (ii) oxygen reduction, and (iii) 2‐phenyl‐naphthyl‐1,4‐dione reduction. Both transient and steady state voltammetric responses are compared. Asymmetric diffusion processes, reaction intermediates, and solubility changes in the ionic liquid are revealed.     

Amperometric Biosensor for Hydrogen Peroxide,Using Supramolecularly Immobilized Horseradish Peroxidase on the β‐Cyclodextrin‐Coated Gold Electrode

Horseradish peroxidase, previously modified with 1‐adamantane moieties, was supramolecularly immobilized on gold electrodes coated with perthiolated β‐cyclodextrin. The functionalized electrode was employed for the construction of an amperometric biosensor device for hydrogen peroxide using 1 mM hydroquinone as electrochemical mediator. The biosensor exhibited a fast amperometric response (6 s) and a good linear response toward H₂O₂ concentration between 12 μM and 450 μM. The biosensor showed a sensitivity of 1.02 mA/M cm², and a very low detection limit of 5 μM. The electrode retained 97% of its initial electrocatalytic activity after 30 days of storage at 4 ⁰C in 50 mM sodium phosphate buffer, pH 7.0.     

Square Wave Electroanalysis at Generator–Collector Gold–Gold Double Hemisphere Junctions

Gold–gold double‐hemisphere junction electrodes with an inter‐electrode gap of typically 1 µm are employed for generator–collector square wave voltammetry. Electrochemical data are recorded as a function of both generator and collector potential to give three‐dimensional response “maps”. At sufficiently low frequencies, close‐to‐steady‐state conditions for the collector response are achieved and peak responses complementary to those for the generator electrode are recorded. Due to localised interelectrode gap diffusion (fast) as opposed to peripheral diffusion (slow), information about reaction products and intermediates can be obtained. Local pH gradient effects provide additional “fingerprint” information beneficial for future application in analytical detection.     

A Glucose Biosensor Based on Immobilization of Glucose Oxidase into 3D Macroporous TiO2

3D macroporous TiO₂ inverse opals have been derived from a sol‐gel procedure using polystyrene colloidal crystals as templates. EDS and SEM showed a face‐centered cubic (FCC) structure TiO₂ inverse opal was obtained. Glucose oxidase (GOx) was successfully immobilized on the surface of indium‐tin oxide (ITO) electrode modified by TiO₂ inverse opal (TiO_2(IO)). Electrochemical properties of GOx/TiO_2(IO)/ITO electrode were characterized by using the three electrodes system. The result of cyclic voltammetry showed that a couple of stable and well‐defined redox peaks for the direct electron transfer of GOx in absence of glucose, and the redox peak height enhanced in presence of 0.1 μM glucose. Compare with the ordinary structured GOx/TiO₂/ITO electrode, inverse opal structured GOx/TiO_2(IO)/ITO electrode has a better respond to the glucose concentration change. Under optimized experimental conditions of solution pH 6.8 and detection potential at 0.30 V versus saturated calomel electrode (SCE), amperometric measurements were performed. The sensitivity and the detection limit of glucose detection was 151 μA cm^?2 mM^?1 and 0.02 μM at a signal‐to‐noise ratio of 3, respectively. The good response was due to the good biocompatibility of TiO₂ and the large effective surface of the three‐dimensionally ordered macroporous structure.     

Ion Transport Across Liquid|Liquid Interfacial Boundaries Monitored at Generator‐Collector Electrodes

Anion transfer processes at a liquid|liquid interface were studied with an interdigitated gold band array electrode. The organic phase, 4‐(3‐phenylpropyl)‐pyridine containing Co(II)phthalocyanine, was immobilised as random droplets at the electrode surface and then immersed into aqueous electrolyte. Oxidation of Co(II)phthalocyanine at the generator electrode was shown to be associated with anion transfer from the aqueous into the organic phase. The corresponding back reduction at the collector electrode with anion expulsion was delayed by the anion/cation diffusion time across the interelectrode gap. A working curve based on a finite difference numerical simulation model was employed to estimate the apparent diffusion coefficients for anions in the organic phase (PF₆^?4^?3^?). Potential applications in ion analysis are discussed.     

Amperometric Tyrosinase Biosensor Based on Carbon Nanotube–Titania–Nafion Composite Film

A highly sensitive and stable amperometric tyrosinase biosensor has been developed based on multiwalled carbon nanotube (MWCNT) dispersed in mesoporous composite films of sol–gel‐derived titania and perfluorosulfonated ionomer (Nafion). Tyrosinase was immobilized within a thin film of MWCNT–titania–Nafion composite film coated on a glassy carbon electrode. Phenolic compounds were determined by the direct reduction of biocatalytically‐liberated quinone species at ?100 mV versus Ag/AgCl (3 M NaCl) without a mediator. The present tyrosinase biosensor showed good analytical performances in terms of response time, sensitivity, and stability compared to those obtained with other biosensors based on different sol–gel matrices. Due to the large pore size of the MWCNT–titania–Nafion composite, the present biosensor showed remarkably fast response time with less than 3 s. The present biosensor responds linearly to phenol from 1.0×10^?7 M to 5.0×10^?5 M with an excellent sensitivity of 417 mA/M and a detection limit of 9.5×10^?8 M (S/N=3). The enzyme electrode retained 89% of its initial activity after 2 weeks of storage in 50 mM phosphate buffer at pH 7.0.     

Characterization and Optimization of Interdigitated Ultramicroelectrode Arrays as Electrochemical Biosensor Transducers

Interdigitated ultramicroelectrode arrays (IDUAs) were fabricated on glass wafers and investigated to obtain optimal oxidation and reduction reactions of potassium ferro/ferrihexacyanide, Fe^2+/3+(CN)₆, when using a 2‐electrode set up. These electrodes will be used as transducers in portable microfluidic‐based biosensors in the future for the detection in an aqueous, biocompatible matrix. IDUAs were designed to maximize the signal‐to‐noise ratio (S/N) investigating electrode height, gap size, finger width, and material. Interesting differences in the electrode materials gold and platinum were found, which were due to the oxidization of platinum and gold during the IDUA fabrication process. It resulted in gold IDUAs being by far superior in respect to signal‐to‐noise ratio and overall signal magnitude to those made of platinum. The effects of gap size, electrode width and number of electrode fingers were as expected. Optimal electrode heights were in the range of 70 nm–140 nm, much larger and smaller electrodes had lower signal‐to‐noise ratios due to overall reduced signal or increased background. The optimized IDUA was made out of gold, had 400 fingers with a finger width of 2.7 μm, a finger height between 70 nm and 140 nm and a gap size of 0.9–1 μm. A detection limit of as low as 0.1 μM ferro/ferrihexacyanide measured in a simple 2‐electrode set up was obtained with a signal‐to‐noise ratio of 9.7.     

Amperometric Ethanol Biosensor Based on Carbon Nanotubes Dispersed in Sol–Gel‐Derived Titania–Nafion Composite Film

Composite solution of sol–gel‐derived titania and perfluorosulfonated ionomer (Nafion) was used as a solubilizing agent for multiwalled carbon nanotubes (CNT) as well as an encapsulation matrix for alcohol dehydrogenase (ADH) for the fabrication of a highly sensitive and stable amperometric ethanol biosensor. ADH was immobilized within a thin film of CNT–titania–Nafion composite film coated on a glassy carbon electrode. Because of the mesoporous nature of the CNT–titania–Nafion composite film, the present biosensor exhibited remarkably fast response time within 2 s. The presence of CNT in the composite film increases not only the sensitivity of the ethanol biosensor but also the long‐term stability of the biosensor. The present biosensor responds linearly to ethanol in the wide concentration ranges from 1.0×10^?5 M to 3.0×10^?3 M with the sensitivity of 51.6 mA M^?1cm^?2. The present biosensor showed good long‐term stability with 75% of its activity retained after 4 weeks of storage in 50 mM phosphate buffer at pH 7.0.     

Electrochemical Detection of Para‐nitrophenol using Copper Metal Nanoparticles Modified Gold Electrode

para‐Nitrophenol (p‐NP) is a high priority environmental pollutant. For the sake of safety, sensitive detection of its presence in water resources and food is highly important. The present article describes the use of copper metal nanoparticles for selective and sensitive electrochemical detection of p‐NP in pure and real sample. For this the gold electrode was fabricated by polyvenylpyrrolidone stabilized copper metal nanoparticles (ca . 4 nm d.) via self‐assembled 4,4′‐bipyridine monolayer and characterized by microscopic and electrochemical techniques. The newly developed sensor permits for sensitive detection of p‐NP in a linear concentration range of 1–500 μM with lowest detection limit of 0.34 nM and high sensitivities 247.1 μA cm⁻² μM⁻¹. The sensor electrode exhibited high stability, reproducibility, good selectivity in the presence of potential interfering agents and had an excellent capability for the selective determination of p‐NP in river water without preliminary treatments.     

Growth and characterisation of diffusion junctions between paired gold electrodes: diffusion effects in generator–collector mode

A diffusion junction between two paired gold electrodes is created in a bipotentiostatic electro-deposition process. Gold metal is deposited simultaneously on two adjacent disc electrodes (100 μm diameter, approximately 125 μm separation) until short-circuit conditions trigger the end point of the electro-deposition. Symmetric gold junctions with typically 5 μm average inter-electrode gap size, 140 μm gap length, and approximately 18 μm junction depth are obtained. These paired gold electrodes are employed in generator–collector mode to give well-defined steady-state feedback currents even for extremely low concentrations of analyte (sub-μM) and without any contributions from capacitive charging. Four redox systems are investigated spanning a wide range of diffusion coefficients: (1) the one-electron oxidation of iodide to iodine, (2) the two-electron oxidation of hydroquinone to benzoquinone, (3) the two-electron reduction of alizarin red S, and (4) the one-electron oxidation of the redox protein cytochrome c. Consistent results for these redox systems suggest that (1) the junction zone between the two electrodes is dominating the behaviour of the electrode in particular for the slower diffusing systems and (2) the paired gold electrode junction can be calibrated and employed for electroanalysis at very low concentrations and for a wider range of analytically relevant redox systems. Dedicated to Professor Keith B. Oldham, on the occasion of his 80th birthday     

Diffusion layer titration of dipyrone in pharmaceuticals at a dual-band electrochemical cell

This paper describes the use of a thin-layered dual-band electrochemical cell operating at flow conditions to determine dipyrone (sodium salt of 1-phenil-2,3-dimethyl-4-methylaminomethanesulfonate-5-pyrazolone) by reaction with electrogenerated iodine. The electrolytic cell consisted of two closely spaced gold electrodes, the upper stream electrode serving as the generator electrode and the downstream electrode working as the collector electrode. A linear dynamic range from 2 to 15 μmol l⁻¹ dipyrone was obtained by using a sample volume of 100 μl, with a detection limit of 1.1 μmol l⁻¹. Standard deviation (S.D.) of 3.4% for 20 repetitive injections of a 40 μmol l⁻¹ dipyrone solution and sampling frequency of 90 h⁻¹ were achieved. The results obtained with the thin-layered dual-band electrochemical cell for dipyrone determination in three different pharmaceutical samples compared well with those found by iodimetry with coulometrically generated iodine.     

Poly(pyrrole‐co‐pyrrole‐2‐carboxylic acid)/Pyruvate Oxidase Based Biosensor for Phosphate: Determination of the Potential,and Application in Streams

A biosensor based on conductive poly(pyrrole‐co‐pyrrole‐2‐carboxylic acid) [Poly(Py‐co‐PyCOOH)] copolymer film coated gold electrode was developed for the quantitative phosphate determination. Enzyme pyruvate oxidase was immobilized chemically via the functional carboxylated groups of the copolymer. The potential to be applied which is deficiency of phosphate biosensor studies for precise phosphate detection was clarified by using differential pulse voltammetry technique. Performance of the sensing ability of the biosensor was improved by optimizing cofactor/cosubstrate concentrations, polymeric film density and pH. The biosensor showed a linearity up to phosphate concentration of 5 mM, operational stability with a relative standard deviation (RSD) of 0.07 % (n=7) and accuracy of 101 % at ?0.15 V (vs. Ag/AgCl). Detection limit (LOD) and sensitivity were calculated to be 13.3 μM and 5.4 μA mM^?1 cm^?2, respectively by preserving 50 % of its initial response at the end of 30 days. It's performance was tested to determine phosphate concentrations in two streams of Zonguldak City in Turkey. Accuracy of phosphate measurement in stream water was found to be 91 %.     

Electrocatalytic Reduction of H2O2 and Oxygen on the Surface of Thionin Incorporated onto MWCNTs Modified Glassy Carbon Electrode: Application to Glucose Detection

A new H₂O₂ enzymeless sensor has been fabricated by incorporation of thionin onto multiwall carbon nanotubes (MWCNTs) modified glassy carbon electrode. First 50 μL of acetone solution containing dispersed MWCNTs was pipetted onto the surface of GC electrode, then, after solvent evaporations, the MWCNTs modified GC electrode was immersed into an aqueous solution of thionin (electroless deposition) for a short period of time <5–50 s. The adsorbed thin film of thionin was found to facilitate the reduction of hydrogen peroxide in the absence of peroxidase enzyme. Also the modified electrode shows excellent catalytic activity for oxygen reduction at reduced overpotential. The rotating modified electrode shows excellent analytical performance for amperometric determination of hydrogen peroxide, at reduced overpotentials. Typical calibration at ?0.3 V vs. reference electrode, Ag/AgCl/3 M KCl, shows a detection limit of 0.38 μM, a sensitivity of 11.5 nA/μM and a liner range from 20 μM to 3.0 mM of hydrogen peroxide. The glucose biosensor was fabricated by covering a thin film of sol–gel composite containing glucose oxides on the surface of thionin/MWCNTs modified GC electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The detection limit, sensitivity and liner calibration rang were 1 μM, 18.3 μA/mM and 10 μM–6.0 mM, respectively. In addition biosensor can reach 90% of steady currents in about 3.0 s and interference effect of the electroactive existing species (ascorbic acid–uric acid and acetaminophen) is eliminated. The usefulness of biosensor for direct glucose quantification in human blood serum matrix is also discussed. This sensor can be used as an amperometric detector for monitoring oxidase based biosensors.     

Prussian Blue Modified Submicron Structured Gold Electrodes for Amperometric Hydrogen Peroxide Sensing

In this work, we present a simple and effective approach for fabricating sub‐micron structured gold (SM−Au) electrodes by chemically etching the magnetron co‐sputtered gold film in KI solution for certain time. Such electrodes with a large surface area to volume ratio were used as the matrix for electrochemical deposition of Prussian blue (PB) to develop an electrochemical hydrogen peroxide sensor. Experimental characterization using scanning electron microscope and atomic force microscope shows that the thickness of PB layer on SM−Au electrode is around 140 nm, and is composited with cubic PB nanocrystals. The electrochemical performance of the designed sensor, studied using cyclic voltammograms and chronoamperometry methods, suggests that the sensor based on SM−Au/PB electrode presents the direct electron transfer of PB particle towards SM−Au film, and exhibits fast response, wide linearity, low detection limit and high stability. Under the optimized conditions, the sensitivity of the developed sensor for the detection of H₂O₂ reaches the value of 512 mA cm⁻² M⁻¹ with a linear range from 1 μM to 4.5 mM.     

A Fast Response Strontium Ion‐Selective Electrode Prepared by Sol‐Gel Membrane Technique

A sol‐gel electrode, based on 6‐(4‐nitrophenyl)‐2‐phenyl‐4,4‐dipropyl‐3,5‐diaza‐bicyclo [3,1,0] hex‐2‐ene (NPDBH) as a neutral ionophore, was successfully developed for the detection of Sr²⁺ in aqueous solutions. Theoretical calculations confirmed NPDBH selectivity toward strontium in comparison with some other metal ions. The electrode responds to Sr²⁺ ion with a sensitivity of 29.1±0.4 mV/decade over the range 8.0×10^?7–1.0×10^?1 M. Selectivity coefficients determined by matched potential method (MPM) indicate high selectivity for strontium ions. The electrode has a fast response time of 11 s and a working pH range of 3.0–10.0. The sol‐gel electrode shows detection limit of 7.5×10^?8 M.     

CuAg nanoparticles formed in situ on electrochemically pre‐anodized screen‐printed carbon electrodes for the detection of nitrate and nitrite anions

CuAg nanoparticles (CuAgNPs) were electrochemically formed in situ on pre‐anodized, screen‐printed carbon electrodes (SPCEs) that possessed many oxygen‐containing functional groups capable of adsorbing metal ions, namely Cu²⁺ and Ag⁺. Pre‐anodization was achieved using continuous cyclic voltammetry in the range of potential 0.3–2.0 V under a scan rate of 50 mV/s. Cu²⁺ and Ag⁺ ions were adsorbed on the pre‐anodized SPCE by immersing the electrode in solutions containing both metal ions, and then CuAgNPs were formed in situ via electrochemical reduction in a deaerated, neat NaClO₄ solution after the electrode was ultrasonicated to remove physically adsorbed metal ions. Although CuNPs showed higher activity than AgNPs toward both nitrate (NO₃⁻) and nitrite (NO₂⁻) ions, the instability of CuNPs hindered the application, so CuAgNPs were employed to achieve a compromise between sensitivity and stability. The SPCE/anodized/CuAgNP electrodes showed activity toward the electrochemical reduction of NO₃⁻ and NO₂⁻, respectively, with the limit of detection (LOD) of 15.6 μM (0.97 ppm) and 11.1 μM (0.51 ppm), which is sufficient to fit the allowed values (50 and 3 ppm, respectively) in drinking water as suggested by the World Health Organization (WHO).     

Electrocatalysis of Nitrate Reduction at Copper‐Nickel Alloy Electrodes in Acidic Media

The cathodic reduction of NO in 1.0 M HClO₄ is investigated by voltammetry at pure Ni and Cu electrodes, and three Cu‐Ni alloy electrodes of varying composition, all configured as rotated disks. Voltammetric data obtained using these hydrodynamic electrodes demonstrate significantly improved activity for NO reduction at Cu‐Ni alloy electrodes as compared to the pure Ni and Cu electrodes. This observation is explained on the basis of the synergistic benefit of different surface sites for adsorption of H‐atoms, generated by cathodic discharge of H⁺ at Ni‐sites, and adsorption of NO at Cu‐sites on these binary alloy electrodes. Koutecky‐Levich plots indicate that the cathodic response for NO at a Cu₇₅Ni₂₅ electrode corresponds to an 8‐electron reduction, which is consistent with production of NH₃. In comparison, the cathodic response at Cu₅₀Ni₅₀ and Cu₂₅Ni₇₅ electrodes corresponds to a 6‐electron reduction, which is consistent with production of NH₂OH. Flow injection data obtained using Cu₅₀Ni₅₀ and Cu₂₅Ni₇₅ electrodes with 100‐μL injections exhibit detection limits for NO of ca. 0.95 μM (ca. 95 pmol) and 0.60 μM (ca. 60 pmol), respectively.     

Pyrolyzed Photoresist Carbon Electrodes for Microchip Electrophoresis with Dual‐Electrode Amperometric Detection

The fabrication and evaluation of pyrolyzed photoresist films (PPF) for microchip capillary electrophoresis (CE) with dual‐electrode electrochemical (EC) detection is described. The sensitivity, linearity, and reproducibility were evaluated using catecholamines and related compounds, including dopamine (DA), 5‐hydroxyindole‐3‐acetic acid (5‐HIAA), ascorbic acid (AA), and catechol. Initial studies with DA show the response of the PPF electrodes to be linear between 25 and 500 μM (r²=0.999) with a limit of detection (LOD) of 5 μM (S/N=3) and sensitivity of 5.8 pA/μM. Selectivity was further enhanced by employing dual‐electrode detection in the series configuration for detection of species exhibiting chemically reversible redox reactions.     

Voltammetric Determination of 2′‐Deoxyadenosine and Adenine in Urine of Patients with Hepatocellular Carcinoma Using Fullerene‐C60‐modified Glassy Carbon Electrode

A fullerene‐C₆₀‐modified glassy carbon electrode has been examined for the simultaneous determination of 2′‐deoxyadenosine (2′‐dAdo) and adenine in human blood and urine using Osteryoung square‐wave voltammetry (OSWV) at pH 7.2. Compared to bare glassy carbon electrode (GCE), the modified electrode displays a shift of the oxidation potential in the negative direction with significant increase in the peak current for both the analytes. At modified electrode well‐defined anodic peaks at potential of 1248 mV and 994 mV are observed for 2′‐dAdo and adenine respectively. Linear calibration curves were obtained within the concentration range 10 nM to 100 μM for both the compounds in 0.1 M phosphate buffer solution (PBS) with the limit of detection 0.8×10^?8 M and 0.95×10^?8 M for 2′‐dAdo and adenine respectively. The analytical utility of the present method is demonstrated by quantitative detection of 2′‐dAdo and adenine in human urine of normal subjects as well as in patients with hepatocellular carcinoma. Interfering effect of some coexisting metabolites has also been reported.