碱性离子液体催化甘油合成1,2-甘油碳酸酯(英)

以离子液体为催化剂,在无溶剂体系中,考察了生物质平台化合物甘油转化1,2-甘油碳酸酯的反应.与酸性离子液体和常用无机碱性催化剂相比,碱性离子液体咪唑基1-丁基-3-甲基咪唑([Bmim]Im)、氢氧化1-丁基-3-甲基咪唑([Bmim]OH)、咪唑基1-烯丙基-3-甲基咪唑([Amim]Im)、氢氧化1-烯丙基-3-甲基咪唑([Amim]OH)在甘油与碳酸二甲酯的酯交换反应中表现出优异的活性.其中,以[Bmim]Im离子液体为催化剂时甘油转化率为98.4%和甘油碳酸酯选择性接近100%.另外,该离子液体可以回收重复利用3次后甘油转化率仍可达92%,甘油碳酸酯选择性可近100%.此碱性离子液体催化方法具有反应结果较好、产物分离简单、条件温和以及环境友好等特点.     

咪唑根碱性离子液体在水介质Knoevenagel反应中的催化作用

报道了咪唑根1-丁基-3-甲基咪唑([Bmim]Im)碱性离子液体的合成与表征,该离子液体具有强碱性和较好的热稳定性.碱性离子液体[Bmim]Im用于催化水介质中Knoevenagel反应,发挥了碱催化剂与相转移催化剂双重作用.此外,离子液体[Bmim]Im及其水溶液还具有良好的循环使用性能.水介质、低催化剂用量、室温...     

离子液体在番茄红素提取中的应用研究

以1-丁基-3-甲基咪唑四氟硼酸盐([Bmim]BF4)、1-丁基-3-甲基咪唑六氟磷酸盐([Bmim]PF6)、1-乙基-3-甲基咪唑四氟硼酸盐([Emim]BF4)、1-乙基-3-甲基溴盐([Emim]Br)、1-丁基-3-甲基咪唑硫酸一氢盐([Bmim]HSO4)离子液体为萃取剂,并用超声波辅助萃取新鲜番茄中的番茄红素.对离子液体超声波辅助萃取新鲜番茄中的番茄红素的条件进行了优化,优化后的提取条件为:以[Bmim]BF4为萃取溶剂,离子液体浓度:V乙醇/V[Bmim]BF4=3,在固定超声温度为40℃,超声萃取时间10min,超声波功率380W,料液比1:5 (g/mL)时,效果最佳.     

吡咯烷酮酸性离子液体中硼酸酯的催化合成

研究了硼酸与频哪醇和环己醇在离子液体1-甲基-2-吡咯烷酮硫酸氢盐（[Hnmp]HSO4）、1-丁基-3-甲基咪唑四氟硼酸盐（[Bmim]BF4）及1-丁基-3-甲基咪唑六氟磷酸盐([Bmim]PF6)中生成2-环己氧基-4,4,5,5-四甲基-1,3,2-二氧硼烷的酯化反应。 考察了不同离子液体、反应温度、反应时间和离子液体与反应物物质的量比等对反应的影响。 结果表明,当n(硼酸)∶n(频哪醇)∶n(环己醇)∶n([Hnmp]HSO4)=1∶1∶1∶1,反应温度为70 ℃和反应时间为4 h时,硼酸酯的产率为72.5%,离子液体重复使用4次,催化活性无明显降低。     

离子液体/H_2O_2体系脱硫实验研究

选取四种不同种类离子液体(ILs),1-丁基-3-甲基咪唑溴化物([Bmim]Br)、1-丁基-3-甲基咪唑四氟硼酸盐([Bmim]BF_4)、1-丁基-3-甲基咪唑硫酸氢盐([Bmim]HSO_4)、1-丁基-3-甲基咪唑磷酸二氢盐([Bmim]H_2PO_4)与30%H_2O_2溶液在温和条件下对两种高硫脱灰煤样(LS、QX)进行脱硫实验研究。用化学法测定脱硫前后煤样形态硫含量,并利用傅里叶变换红外光谱(FT-IR)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)及热重(TG)对脱硫前后的煤样进行表征。结果表明,离子液体的加入使H_2O_2氧化脱硫能力增强,煤中硫铁矿硫和有机硫化物硫被显著脱除;经ILs/H_2O_2体系作用后的煤样中小粒径的颗粒减少,颗粒间的缝隙增大,煤表面的凹坑明显,热重实验结果表明,ILs/H_2O_2体系作用后的煤样相对于原煤热失重增大,部分挥发性物质释放峰温提前。     

不同离子液体中硝基苯的电化学还原

研究了硝基苯在N-甲基咪唑对甲基苯磺酸([Mim][PhSO3])和1-丁基-3-甲基咪唑六氟磷酸([Bmim][PF6])两种离子液体中的电化学还原反应.循环伏安法测试显示,硝基苯在[Mim][PhSO3]中只出现一个还原峰,是一个受扩散控制的不可逆电化学反应,而在[Bmim][PF6]中出现两对氧化还原峰,表明其还原产物随离子液体性质的不同而异.     

先锋褐煤在离子液体中温和加氢转化研究

对先锋褐煤在离子液体1-丁基-3-甲基咪唑四氟硼酸盐([Bmim]BF₄)中于温和条件下(350 ℃)的加氢液化行为进行了研究.主要考察了催化剂FeS、ZnCl₂、AlCl₃和FeCl₃对先锋褐煤在离子液体[Bmim]BF₄中液化性能的影响规律,并对液化产物进行了红外光谱分析.研究发现,先锋褐煤在离子液[Bmim]BF₄、催化剂和四氢萘(THN)作用下具有较好的液化性能.在350 ℃、[Bmim]BF₄和ZnCl₂作用下,先锋褐煤的液化产物产率为66.2%,主要的液化产物为四氢呋喃可溶物(THFS)、四氢呋喃不溶而N-甲基吡咯烷酮可溶的产物(NS).液化产物的红外光谱分析结果表明,催化剂的种类显著影响液化产物的分布和结构.     

壳聚糖在4种咪唑型离子液体中溶解性的研究

研究、比较了壳聚糖在4种咪唑型离子液体氯化1-丁基-3-甲基咪唑([BMIM]Cl)、1-丁基-3-甲基咪唑醋酸盐([ BMIM] Ac)、1-乙基-3-甲基咪唑醋酸盐([EMIM] Ac)和氯化1-烯丙基-3-甲基咪唑([AMIM] Cl)中的溶解性,提出了可能的溶解机理,并利用红外光谱(FTIR)、热重分析(TGA...     

[Amim]Cl离子液体中微波辐射加热促进稻草秸秆酸水解制备还原糖

在1-烯丙基-3-甲基咪唑氯盐([Amim]Cl)离子液体介质中,用微波辐射加热促进稻草秸秆纤维素的酸水解,探讨了微波辐射加热及离子液体对酸催化植物纤维素水解的促进作用;并对水解产物中的还原糖进行了测定,着重考察了离子液体用量、硫酸浓度、微波功率、反应温度、反应时间等因素对还原糖收率的影响.结果表明,在[Amim]Cl...     

离子液体中微波辅助的 Lewis 酸催化纤维素制备 5-羟甲基糠醛

 以离子液体 1-丁基-3-甲基咪唑氯为溶剂, 以 CrCl3•6H2O 为催化剂, 直接转化纤维素生成 5-羟甲基糠醛 (HMF). 考察了微波辐射条件、反应温度、反应时间及催化剂用量对 HMF 产率的影响. 结果表明, 在最佳条件下, HMF 产率可达 55%.     

催化热解生物质制取富氢气体的研究

在实验室自制的固定床反应器上, 考察了秸秆和锯屑的热解行为, 研究了热解产物分布特别是富氢气体的体积分数和产率, 着重研究了（5种金属氧化物和2种碳酸盐催化剂）的催化效果。结果表明,温度从500 ℃提高到850 ℃, 秸秆和锯屑的热解气产率分别从29.0%提高到40.6%, 35.0％提高到46.5%, 而对应的富氢气体的体积分数分别从41.2％提高到48.2%, 40.6％提高到47.0%；在5种金属氧化物中，Cr2O3显示了最好的催化效果，在750 ℃时对应的热解气产率与不使用催化剂相比提高了10％，富氢气体的体积分数提高了13％；催化剂（CaCO3和Na2CO3）占生物质的质量分数对热解气和富氢气体产率有明显的影响，当质量分数从0增加到30％时， 热解气和富氢气体产率增加较明显，而后其值的增加可以忽略， 因此推荐使用的催化剂质量分数为30％。     

餐饮垃圾热解制取生物燃油的实验研究

主要研究温度、餐饮垃圾种类以及催化剂对餐饮垃圾热解所制生物燃油的产率和品质的影响。结果表明,猪肉和米饭的最佳产油温度均为410℃,白菜的最佳产油温度为450℃。米饭、白菜、猪肉的产油率分别为45.02%、25.60%、71.26%。采用氧弹热量计对其热值进行测定,米饭和白菜热解油的高位热值较低,分别为18.30MJ/kg和17.49MJ/kg;而猪肉热解油的高位热值为36.57 MJ/kg, 并且黏稠度较高。催化剂Co-MCM-41的催化效果明显,使餐饮垃圾的产油率由41.99%提高到66.30%,同时使热解油中的含氧化合物明显降低,而烷烃类和烯烃类的含量明显增加,高位热值由30.30MJ/kg提高到32.74MJ/kg。通过物理吸附仪对新制备的和使用一次后再生的催化剂Co-MCM-41进行表征,结果表明,催化剂Co-MCM-41再生后孔容、孔径和比表面积变化不大,性质基本不变,活性依然存在。
     

The thermochemistry of solvation of imidazolium-based ionic liquids in benzene

ABSTRACT

The present work is devoted to the thermochemical study of solvation of ionic liquids (IL) in benzene. The solution enthalpies of 1-ethyl-3-methylimidazolium tricyanomethanide [EMIM][C(CN)₃], 1-butyl-3-methylimidazolium tetrafluoroborate [BMIM][BF₄], 1-hexyl-3-methylimidazolium hexafluorophosphate [HMIM][PF₆], 1-octyl-3-methylimidazolium tetrafluoroborate [OMIM][BF₄], 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [EMIM][NTf₂], 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [BMIM][NTf₂] and 1-butyl-3-methylimidazolium trifluoromethanesulfonate [BMIM][TfO] in benzene were measured. The solvation enthalpies of imidazolium-based IL were calculated. Molar refractions of imidazolium-based IL form literature data on density and refractive indexes of IL were also calculated. The linear correlation between solvation enthalpy and molar refraction of IL was observed. This correlation can be used to calculate the vaporization enthalpy of imidazolium-based IL from solution calorimetry data.     

Microwave pyrolysis of straw bale and energy balance analysis

The compressed wheat and corn straw bale were pyrolyzed on a microwave heating device self-designed and built with respect to the time-resolved temperature distribution, mass loss and product properties. Considering scale up and technology promotion of microwave pyrolysis (MWP), the investigations on electricity consumption and energy balance of MWP were carried out emphatically. The results indicated that MWP had obvious advantages over conventional pyrolysis, such as heating rapid and more valuable products obtained. The distribution of pyrolysis products such as gas, liquid and char was close to 1:1:1 due to the medium pyrolysis temperature and the slow heating rate, which was not favorable for the formation of gas and/or liquid products. The content of H₂ attained the highest value of 35 vol.% and syngas (H₂ and CO) was greater than 50 vol.%. The electricity consumption of MWP was between 0.58 and 0.65 kW h (kg straw)⁻¹ and with the increase of microwave power, the electricity consumption required for pyrolysis of unit mass of straw increased. The minimum microwave power for MWP was about 0.371 kW (kg straw)⁻¹ and the proportion of heat loss and conversion loss of electricity to microwave energy occupied in the total input energy was 42%. Data and information obtained are useful for the design and operation of pyrolysis of large-sized biomass via microwave heating technology.     

Enhanced saccharification of lignocellulosic biomass with1-allyl-3-methylimidazolium chloride（Amim Cl） pretreatment

A simple and efficient method of enhancing biomass saccharification by microwave-assisted pretreatment with dimethyl sulfoxide/1-allyl-3-methylimidazolium chloride is proposed. Softwood（pine wood（PW））, hardwoods（poplar wood, catalpa bungi, and Chinese parasol）, and agricultural wastes（rice straw, wheat straw, and corn stover（CS）） were exploited. Results showed that the best pretreatment effect was in PW with 54.3% and 31.7% dissolution and extraction ratios, respectively. The crystal form of cellulose in PW extract transformed from I to II, and the contended cellulose ratio and glucose conversion ratio reached 85.1% and 85.4%, respectively. CS after steam explosion achieved a similar pretreating effect as PW, with its cellulose hydrolysis ratio reaching as high as 91.5% after IL pretreatment.     

添加乙酸乙酯对生物油稳定性的影响

以稻草秸秆快速热裂解生物油为样品,选取乙酸乙酯作为添加剂,按不同质量分数(分别为1%、6%、11%、16%和21%)添加到生物油中,考察原始生物油(空白组)及乙酸乙酯组生物油理化特性随贮存时间的变化规律。结果表明,随着乙酸乙酯添加质量分数增大,各乙酸乙酯组(1%、6%、11%、16%和21%)生物油最终pH值比空白组分别提高0.66%、2.33%、3.65%、4.32%和6.31%;最终含水率比空白组分别降低10.90%、20.17%、28.19%、30.27%和35.10%;最终运动黏度比空白组分别降低13.69%、39.08%、57.99%、66.00%和73.58%。FT-IR和GC-MS分析结果表明,添加乙酸乙酯能抑制生物油老化反应。此外,GC-MS分析结果还证实乙酸乙酯可以减少生物油内有机酸含量。     

Modification of Rice Straw for Heavy Metal Ion Adsorbents by Microwave Heating

Summary: Cellulose in rice straw was chemically modified by phosphorylation using conventional heating or microwave heating. Rice straw pretreated by NaOH solution gave the highest phosphorus content when it was phosphorylated using microwave heating at 450 watt (7.07%P, ion exchange capacity 2.60 meq/g). The 3 hour-reaction in oil bath yielded the modified rice straw with lower of phosphorus content (6.32%P) and higher ion exchange capacity (2.99 meq/g) than that of microwave heating. The feasibility of the modified rice straw as cation sorbents for removing heavy metal was investigated. Cd²⁺, Cr³⁺ and Pb²⁺ were used as sorbates. In sorption test of 40 ppm with 2.0 g/L of the modified rice straw, both modified rice straws could adsorb metal ions faster than the commercial ion exchange resin (dowax) at the time less than 60 min. The modified rice straw prepared by microwave heating (A-MCW2) could remove 90% of Cd²⁺ and Cr³⁺ in 60 minutes and remove 99% of Pb²⁺ after 30 min.     

Scale-up of microwave heating process for the production of bio-oil from sewage sludge

A pilot-scale microwave heating apparatus was constructed for the production of bio-oil from sewage sludge, and the effects of important microwave processing parameters and chemical additives on the quality and yield of bio-oils were investigated. It was found that bio-oil was mainly formed at the pyrolysis temperature range of 200–400 °C. A higher heating rate (faster pyrolysis) not only increased the yield of bio-oil, but also improved the quality of bio-oil according to the elemental composition and calorific values. The maximum bio-oil yield was 30.4% of organic fraction, obtained from the pyrolysis of original sewage sludge at microwave radiation power of 8.8 kW and final pyrolysis temperature of 500 °C. All of five simple additives (KOH, H₂SO₄, H₃BO₃, ZnCl₂, and FeSO₄) reduced the bio-oil yield, but the composition and property of bio-oil varied with the additive types greatly. KOH, H₂SO₄, H₃BO₃ and FeSO₄ were found to improve the quality of bio-oils remarkably according to the calorific value, density, viscosity and carbon content of bio-oils, but ZnCl₂ treatment went against that. GC–MS analysis of the bio-oils showed that, alkali treatment promoted the formation of alkanes and monoaromatics, while acid treatment favored the formation of heterocyclics, ketones, alcohols and nitriles. Compared with sulfate slat FeSO₄, chloride salt ZnCl₂ was a better catalyst for selective catalytic pyrolysis of sewage sludge. The addition of ZnCl₂ only promoted the formation reactions of a few kinds of nitriles and ketones remarkably. It is technologically feasible to produce bio-oil form microwave-induced pyrolysis of sewage sludge by optimizing pyrolysis conditions and selecting appropriate additives.     

Microwave activation in ionic liquids induces high temperature-high speed electrochemical processes

Self-focusing of intense microwave radiation at the tip of a 25 microm diameter platinum disk microelectrode immersed into the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM(+)PF(6)(-)) containing 1 mM ferrocene causes dramatically (two orders of magnitude) enhanced voltammetric current signals and temperatures in excess of 600 K (at the electrode surface)--extreme conditions sufficient for condensed phase pyrolysis processes to occur.     

Microwave-assisted separation of ionic liquids from aqueous solution of ionic liquids

Microwave-assisted separation has been applied to recover ionic liquid (IL) from its aqueous solution as an efficient method with respect to time and energy compared to the conventional vacuum distillation. Hydrophilic ILs such as 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim][BF(4)]), 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([Bmim][TfO]) and 1-ethyl-3-methylimidazolium methylsulfate ([Emim][MS]) could be recovered in 6 min from the mixture of ILs and water (1:1, w/w) under microwave irradiation at constant power of 10 W while it took at least 240 min to obtain ILs containing same water content (less than 0.5 wt%) by conventional vacuum oven at 363.15 K with 90 kPa of vacuum pressure. Energy consumptions per gram of evaporated water from the homogeneous mixture of hydrophilic ILs and water (1:1, w/w) by microwave-assisted separation were at least 52 times more efficient than those in conventional vacuum oven. It demonstrated that microwave-assisted separation could be used for complete recovery of ILs in sense of time and energy as well as relevant purity.