Site percolation model for latex film formation in soft polymer matrix

The UV-visible (UVV) technique was used to monitor latex film formation in a soft polymer matrix. Various film samples were prepared by increasing the amount of poly(methyl methacrylate) (PMMA) particles in a poly(isobutylene) (PIB) matrix. These samples were then annealed above the glass transition temperature to promote latex film formation. Transmitted photon intensities, Itr, were measured for each film. It is observed that Itr decrease as the latex content is increased, which was explained by the increase in scattered light intensity, Isc. The drastic increase in Isc above a certain latex content is attributed to the site percolation of latex particles in the PIB matrix. The percolation threshold and the critical exponent were measured and found to be 0.3 and 0.4, respectively. The increase in Itr by annealing of film samples above Tg was explained with the void closure process below 0.8 occupation probability. When the film is occupied completely with the latex particles, interdiffusion of polymer chains was observed. Viscous flow and chain diffusion activation energies were determined and found to be 8 and 51 kcal/mol, respectively.     

Film formation from pure and mixed latices; transient fluorescence study

A fast transient fluorescence technique was used to study latex film formation induced by organic solvent vapor. Mixtures of pyrene (P)- and naphthalene (N)-labeled and/or pure naphthalene-labeled latex films were prepared separately from poly(methyl methacrylate) (PMMA) particles. Then these pure and mixed latex films were exposed to vapor of various chloroform-heptane mixtures in seven different experiments. In both films, fluorescence lifetimes from N were monitored during vapor-induced film formation. It was observed that N lifetimes decreased as the vapor exposure time is increased. A Stern-Volmer kinetic analysis was used for low quenching efficiencies to interpret the decrease in N lifetimes. A Prager-Tirrell model was employed to obtain back-and-forth frequencies, nu, of reptating PMMA chains during latex film formation induced by solvent vapor. In both pure and mixed latex films, nu values were found to be correlated with the chloroform content in the vapor mixture. It was observed that polymer interdiffusion obeyed a t1/2 law during film formation.     

Interdiffusion of polymer chains during latex coating

The fluorescence method was used to study the interdiffusion of polymer chains during annealing of latex above its glass transition temperature (T_g). The latex film was prepared from mixture of naphthalene (N) (donor) and pyrene (P) (acceptor)-labeled poly(methyl methacrylate) (PMMA) latex particles. Heptane was used as the coalescent agent. A steady-state fluorescence technique was employed to measure the amount of direct nonradiative energy transfer from N to P during the interdiffusion of polymer chains across the particle–particle junction. Various latex films with different latex contents were used to measure the percentage critical occupation for the reliable steady-state fluorescence measurements. Diffusions activation energies in these latex films were measured and found to be around 30 kcal/mol, which was attributed to the backbone motion of PMMA chains.     

Effect of Molecular Weight on Packing during Latex Film Formation

A UV-visible technique is used to study the evolution of transparency during film formation from latex particles. Latex particles with high and low molecular weight (HM and LM) polymethyl methacrylate (PMMA) are used to prepare films. Two sets of films with different latex content were prepared from HM and LM particles separately, by annealing PMMA particles above the glass transition temperature. Transmitted photon intensity, I(tr), from HM and LM films increased as the annealing temperature was increased. The increase in the transmitted photon intensity is attributed to the latex content (film thickness) for the annealed film samples. It is suggested that as the latex particles are packed (film thickness is increased) fewer voids or cracks are formed in the films. Positive and negative absorption coefficients are measured below and above 210 and 180 degrees C annealing temperatures for the HM and LM films. Packing coefficients are obtained for films in various latex contents. It is observed that LM particles are packed much easier than HM particles. Copyright 2001 Academic Press.     

In vitro cytotoxicity evaluation of natural rubber latex film surface coated with PMMA nanoparticles

In order to increase surface roughness of the sulphur-prevulcanized natural rubber (SPNR) film and, hence, decrease the direct contact between the rubber and skin, the poly(methyl methacrylate) (PMMA) latex particles were deposited onto the SPNR film grafted with polyacrylamide (SPNR-g–PAAm). The surface coverage of PMMA particles on the SPNR-g–PAAm increased with increasing latex immersion time, particle size and concentration. Prior to the in vitro cytotoxicity evaluation on L-929 fibroblasts, the SPNR and SPNR-g–PAAm coated with PMMA particles were extracted by using the culture medium. Results showed that the cytotoxicity effect could be significantly reduced by coating PMMA particles onto the rubber film. At the extract concentrations of ≤12.5% for 24 h at 37 °C, no toxicity potential was detected. The study will be helpful for development of gloves designed for the hypersensitive person.     

Fast transient fluorescence technique (FTRF) for studying vapor-induced latex film formation

A fast transient fluorescence (FTRF) technique was used to study latex film formation induced by organic solvent vapor. Seven different films with the same latex content were prepared separately from poly(methyl methacrylate) (PMMA) particles and exposed to vapor of various chloroform-heptane mixtures in seven different experiments. Latex films were prepared from pyrene (Py)-labeled latex particles and fluorescence lifetimes of Py were monitored during vapor-induced film formation. It was observed that pyrene lifetimes decreased as vapor exposure time increased. A Stern-Volmer kinetic analysis was used for low quenching efficiencies to interpret the decrease in pyrene lifetimes. A Prager-Tirrel model was employed to obtain back-and-forth frequencies, nu, of the reptating PMMA chains during latex film formation induced by solvent vapor. nu values were found to be correlated with chloroform content in vapor mixture. It was observed that polymer interdiffusion obeyed a t(1/2) law during film formation. The results of optical transmission experiments were found to support these findings.     

Study of bulk morphology of polymer latex films using laser confocal fluorescence microscopy

Ｐｏｌｙｍｅｒｆｉｌｍｆｏｒｍａｔｉｏｎｆｒｏｍｅｉｔｈｅｒｌａｔｅｘｏｒｓｏｌｕｔｉｏｎｉｓｑｕｉｔｅａｎｉｎｔｅｒｅｓｔｉｎｇｂｕｔｃｏｍｐｌｉｃａｔｅｄｓｕｂｊｅｃｔｄｅａｌｉｎｇｗｉｔｈｄｉｆｆｕｓｉｏｎ,ｉｎｔｅｒｐｅｎｅｔｒａｔｉｏｎａｎｄｃｏａｇｕｌａｔｉｏｎｏｆｐｏｌｙｍｅｒｃｈａｉｎｓ,ａｎｄｅｓｐｅｃｉａｌｌｙｃｏｒｒｅｌａｔｅｄｔｏｔｈｅｐｒｏｐｅｒｔｉｅｓｏｆｔｈｅｆｉｎａｌｌｙｆｏｒｍｅｄｆｉｌｍ.Ｍａｎｙｓｔｕｄｉｅｓ[1—3]ｈａｖｅｂｅｅｎｃａｒｒｉｅｄｏｕｔｏｎｌａｔ…     

聚合物纳米微粒静电组装行为及其表征

使用2,2′-偶氮二异丁基脒二盐酸盐自由基引发剂,改变甲基丙烯酰氧乙基十六烷基二甲基溴化铵阳离子功能单体的量与苯乙烯进行乳液聚合获得不同粒径的阳离子乳胶粒,使用十二烷基硫酸钠为乳化剂和过硫酸钾为引发剂制备阴离子聚合物乳胶粒.采用基于静电相互作用的异凝聚法将以上2种带有相反电荷的乳胶粒组装,获得了表面粗糙程度不同的复合微粒.对异凝聚过程中复合液透光率和微粒大小及分布进行跟踪测试,并用透射电子显微镜表征了阳离子微粒、阴离子微粒以及复合微粒的形态和大小.结果表明,在一定范围内可以通过控制阴离子乳胶粒与阳离子乳胶粒的复合比例改变单个复合微粒表面阳离子小微粒的数目.     

Film Formation from Nanosized Copolymeric Latex Particles: A Photon Transmission Study

The photon transmission technique was used to monitor the evolution of transparency during film formation from nanosized copolymeric latex particles. The latex films were prepared from poly(methyl methacrylate-co-butyl methacrylate) (P(MMA-co-BMA)) particles which were produced by microemulsion polymerization. These films were annealed at elevated temperatures in various time intervals above the glass transition temperature (T(g)) of P(MMA-co-BMA). It is observed that the transmitted photon intensity (I(tr)) from these films increased as the annealing temperature increased. There are three different film formation stages. These stages are explained by the void closure, healing, and interdiffusion processes, respectively. The activation energies for viscous flow (DeltaH approximately 16 kcal/mol), minor chains (DeltaE(H) approximately 27 kcal/mol), and backbone motion (Delta E(b) approximately 132 kcal/mol) were obtained using various models. Void closure (tau(v), T(v)) and healing points (tau(H), T(H)) were determined. Using the time-temperature pairs, void closure and healing activation energies were measured and found to be 21 and 30 kcal/mol, respectively. Copyright 2001 Academic Press.     

Prevulcanisation of skim latex: morphology and its use in natural rubber based composite material

The prevulcanisation of skim latex, a by-product of field natural rubber (NR) latex concentrated by centrifugation, using sulphur and peroxide systems was investigated. Compared to the peroxide prevulcanisation, the lower swelling ratio of film casted from sulphur-prevulcanised skim (SPVS) latex was observed. The latter was then employed for preparation of NR/SPVS core–shell particles by using heterocoagulation technique whose driving force was an interpolymer complex between poly(ethylene oxide) (PEO) moieties of a non-ionic surfactant (Nonidet) adsorbed on small SPVS particles and the indigenous surfactant (protein–lipid) on a large NR particle. The value of zeta potential of heterocoagulated particle and the better oil resistance of films casted from the composite latex when compared to that of the NR film revealed the NR/SPVS core–shell structure.     

复合微乳液聚合制备P(MMA-UA)纳米乳胶粒子的研究

将聚氨酯预聚体可聚合乳化剂 (APUA)和甲基丙烯酸甲酯 (MMA)的复合微乳液体系 ,分别用水溶性过硫酸钾 (K2 S2 O8)和油溶性偶氮二异丁腈 (AIBN)作引发剂 ,进行微乳液聚合研究 ,制备了P(MMA UA)复合纳米乳胶粒子 .研究了APUA用量、聚合温度对聚合动力学的影响 ;用透射电子显微镜 (TEM)观察了不同乳化剂浓度及引发剂体系对胶粒形态、大小及分布的影响 .结果表明 ,用可聚合乳化剂APUA可制得稳定性很好的P(MMA UA)纳米级核 壳型乳胶粒子 ,乳胶粒径在 5 0nm左右 .随着乳化剂用量增加 ,粒子变小 ;不同类型的引发剂对胶乳的性质有较大影响 ,以APUA为乳化剂 ,K2 S2 O8为引发剂 ,在聚合反应过程中或在聚合反应后的放置中 ,会出现P(MMA UA)的纳米水凝胶 (Nanogel)现象 .     

Synthesis of nano-ZnO/poly(methyl methacrylate) composite microsphere through emulsion polymerization and its UV-shielding property

Nano-ZnO/poly(methyl methacrylate)(PMMA) composite latex microspheres were synthesized by in-site emulsion polymerization. The interfacial compatibility between nano-ZnO particles and PMMA were improved by treating the surface of nano-ZnO particles hydrophobically using methacryloxypropyltrimethoxysilane (MPTMS). TEM indicated that nano-ZnO particles present in nanosphere and have been encapsulated in the PMMA phase. FT-IR confirmed that MPTMS reacted with the nano-ZnO particle and copolymerized with MMA. It was clearly found from SEM that ZnO nanoparticles can be homogeneously dispersed in the PVC matrix. The absorbance spectrum of the nanocomposite polymer suggested that increasing the amount of nano-ZnO in composite particles could enhance the UV-shielding properties of the polymers. The nano-ZnO/PMMA composite particle could eliminate aggregation of ZnO nanoparticle and improve its compatibility with organic polymer. This means that the composite particles can be widely applied in lots of fields.     

EFFECT OF THE PHASE STRUCTURE EVOLUTION ON THE PROPERTIES OF FILMS FORMED FROM PBA/P(St-co-MMA) COMPOSITE LATEX

A group of heterogeneous latexes poly(butyl acrylate)/poly(styrene-co-methyl methacrylate)(PBA/P(St-co-MMA)) were prepared by a semi-continuous seeded emulsion polymerization process under monomer starved conditions.The glass transition temperature(T_g)and the mechanical properties of the film formed from the composite latex changed with the evolution of the particle morphology.A photon transmission method was used to monitor the phase structure evolution of films which were prepared from core-shell PBA/...     

悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

Latex interpenetrating polymer networks of epoxidised natural rubber/poly(methyl methacrylate): an insight into the mechanism of epoxidation

Composite latex particles consisting of epoxidised natural rubber (ENR) and poly(methyl methacrylate) (PMMA) were synthesised to obtain interpenetrating polymer networks. Among the ENR latices having 9 to 36 mol% epoxide, prepared by in situ reaction using performic acid, the ENR latex with 25 mol% epoxide was selected for prevulcanisation by sulphur or γ-radiation system. The swelling ratios of sheets cast from the sulphur-prevulcanised ENR (SPENR) latices decreased with increasing prevulcanisation time while those cast from the γ-radiation-prevulcanised ENR latices were also inversely proportional to the irradiation dose. By applying the phase transfer/bulk polymerisation/transmission electron microscopy (TEM) technique, a homogeneous network structure in each of the SPENR particles and also a relative dense network near the surface in γ-radiation (RV) ENR particle were noticed. When 10 to 30 wt% of MMA swollen in ENR particles was polymerised, the mesh structure was observed in each particle. The dense network near the RVENR particle surface might be used as additional evidence that the degree of epoxidation and, hence, the presence of swollen n-butyl acrylate in the outer zone were higher than in the internal region.     

The characterization of latex particles prepared by pulsed electron beam induced emulsion polymerization

The emulsion polymerization of styrene (St) and methyl methacrylate (MMA) induced by 10 MeV pulsed electron beams (PEB) was investigated. The monomer conversion of MMA and St was found to be very low so that the final prepared poly(methyl methacrylate) (P(MMA)) and polystyrene (PS) latex particles exhibit porous structures, as verified by TEM and SEM observations. The results of dynamic light scattering (DLS) and gel permeation chromatography (GPC) showed that both the particle size and the molecular weight of PS and PMMA latexes decrease with the increase of the absorbed dose. However, the molecular weights and the particle sizes of the PS and PMMA latexes change differently with the irradiation time. This work indicated that emulsion polymerization induced by high energy electron beam has an advantage over that induced by γ-ray or chemical initiators in the preparation of latex with a low molecular weight and porous structure.     

Preparation and clinical application of immunomagnetic latex

Magnetic poly(methyl methacrylate) (PMMA)/poly(methyl methacrylate‐co‐methacrylic acid) [P(MMA–MAA)] composite polymer latices were synthesized by two‐stage soapless emulsion polymerization in the presence of magnetite (Fe₃O₄) ferrofluids. Different types and concentrations of fatty acids were reacted with the Fe₃O₄ particles, which were prepared by the coprecipitation of Fe(II) and Fe(III) salts to obtain stable Fe₃O₄ ferrofluids. The Fe₃O₄/polymer particles were monodisperse, and the composite polymer particle size was approximately 100 nm. The morphology of the magnetic composite polymer latex particles was a core–shell structure. The core was PMMA encapsulating Fe₃O₄ particles, and the shell was the P(MMA–MAA) copolymer. The carboxylic acid functional groups (COOH) of methacrylic acid (MAA) were mostly distributed on the surface of the composite polymer latex particles. Antibodies (anti‐human immunoglobulin G) were then chemically bound with COOH groups onto the surface of the magnetic core–shell composite latices through the medium of carbodiimide to form the antibody‐coated magnetic latices (magnetic immunolatices). The MAA shell composition of the composite latex could be adjusted to control the number of COOH groups and thus the number of antibody molecules on the magnetic composite latex particles. With a magnetic sorting device, the magnetic immunolatices derived from the magnetic PMMA/P(MMA–MAA) core–shell composite polymer latex performed well in cell‐separation experiments based on the antigen–antibody reaction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1342–1356, 2005     

Kinetics of latex formation of PBMA latex in the presence of alkali soluble resin using atomic force microscopy

 The effect of alkali-soluble resin (ASR), poly(ethylene-co-acrylic acid), EAA, postadded to emulsifier-free monodisperse poly(butyl methacrylate) (PBMA) latexes on the kinetics of film formation was investigated using atomic force microscopy (AFM). Corrugation height of latex particles in films was monitored at various annealing temperatures as a function of annealing time. Enhanced polymer diffusion was found in a latex film containing ASR regardless of anneal-ing temperature. With increasing annealing temperature, a much higher rate of polymer diffusion was found in latex films containing ASR. These results can be interpreted that the low molecular weight and low Tg EAA resin adsorbed at the particle surface is more susceptible to diffusion than that of the PBMA in the film formation stage, thus it enhances the mobility of PBMA polymer. Received: 30 October 1997 Accepted: 20 March 1998     

Dispersion polymerization of methyl methacrylate in supercritical CO2 in the presence of non-fluorous random copolymers

A series of non-fluorous random copolymers, composed of 3-[tris(trimethylsilyloxy)silyl] propyl methacrylate and 2-dimethylaminoethyl methacrylate, poly(SiMA-co-DMAEMA) with different comonomer ratios were prepared and utilized as stabilizers for the free radical dispersion polymerization of methyl methacrylate (MMA) in supercritical carbon dioxide (scCO₂). It was demonstrated that the composition and concentration of the stabilizer have a dramatic effect on the morphology of resulting poly methyl methacrylate (PMMA) latex. When the copolymeric stabilizer poly(SiMA-co-DMAEMA) (71:29) was employed, free-flowing spherical PMMA particles were produced in high yield. As the concentration of stabilizer increases, the resulting size of colloidal particles decreases. In addition, the monomer concentration and initial pressure affected the particle diameter of PMMA.     

The effect of clay on the morphology of multiphase latex particles

The effect of montmorrilonite clay (MMT) platelets on the morphology of polystyrene/poly(methyl methacrylate) (PMMA) composite latex particles prepared via PMMA-seeded (semi-) batch emulsion polymerization of styrene was studied. It was found that the particle morphology obtained greatly depended on the ability of the clay platelets to diffuse through the polymer particle. Indeed, when the reactions were strictly under kinetic control, i.e., where the clay platelets were unable to diffuse during polymerization, anisotropic core-shell-like morphologies with split core were observed. A better mobility of the clay platelets could more or less restrict the diffusion of the second-stage polymers within the host polymer, leading to original kinetically controlled morphologies. In the case of a full migration of the clay platelets to the particle surface, the penetration of the second-stage polymer species in the seed latex was found to be more limited, enhancing the formation of secondary particles.