Ferric hydrous oxide sols I. Monodispersed basic iron(III) sulfate particles

The methods of preparation of basic ferric sulfate sols consisting of particles uniform in shape of extremely narrow size distribution are described in detail. To produce such sols, acidic solutions containing ferric ions and sulfate ions were aged at elevated temperatures for a few hours. Solids formed from solutions containing a mixture of a ferric salt with a metal sulfate consisted of Fe₃(SO₄)₂(OH)₅· 2H₂O, which is the basic formulation for the alunite mineral group, whereas particles formed from ferric sulfate solutions also included Fe₄(SO₄)-(OH)₁₀ in varying proportions. The morphology of the particles was strongly dependent on the [Fe³⁺]: [SO₄²⁻] ratio in solution. Changes in the cation (K⁺, NH₄⁺, Na⁺) of the sulfate salt used in the mixture with ferric nitrate solutions greatly affected the particle size and also exhibited some effect on the lattice parameters. Certain cations (Mg²⁺, Ni²⁺, Cu²⁺) completely inhibited particle formation. During the first few hours of growth of the Fe₃(SO₄)₂-(OH)₅· 2H₂0 particles their diameters increased essentially linearly with time, indicating that the rate determining step was the surface reaction. The relevance of these systems to the study of corrosion of iron and steel is discussed.     

Precipitation of monodispersed basic iron(III) sulfate (sodium jarosite) particles

Uniform sodium jarosite particles were obtained by forced hydrolysis of ferric salt solutions to which copper sulfate, sodium sulfate, and sodium nitrate were added. It was found that at the same concentrations of ferric and sulfate ions the particle size and yield decreased with the lowering of the concentration of sodium ions, but the morphology remained the same. At a sufficiently small content of sodium in the reacting solution, no precipitation of sodium jarosite particles was observed. Finally, chemical and XRD analyses showed that small amounts of copper ions are incorporated in the crystal lattice which, with the change in the Na⁺/H₃O⁺ ratio, slightly affected the structure of this mineral, but not its other properties. Received: 12 July 2000 Accepted: 18 August 2000     

Sorption Properties of Hematite for Copper Ions

Sorption properties of commercial hematite (α-Fe₂O₃) for divalent copper ions were studied. This was done with a model solution of copper(II) sulfate additionally containing 400 mg L^–1 of sodium sulfate. It was shown that the hematite sample under study is a good sorbent for removal of divalent copper ions from aqueous solutions. The process of Cu²⁺ sorption is described by the Langmuir equation. The parameters of this equation were determined at various pH values of the model solution and compared with similar published parameters for other hematite samples.     

Solubility of dimethyldisulfide (DMDS) in aqueous solutions of Fe(III) complexes of trans-1,2-cyclohexanediaminetetraacetic acid (CDTA) using the static headspace method

Total reduced sulfurs quartet (H₂S, CH₃SH, CH₃SCH₃ and CH₃S₂CH₃) is part of a well-known environmental problem afflicting pulp mills exploiting the Kraft mill sulfate-pulp process. Utilization of ferric chelate complex of trans-1,2-cyclohexanediaminetetraacetic acid (CDTA) for the oxidative scrubbing of H₂S and CH₃SH in Kraft mill streams is beneficial from the standpoints of iron protection against precipitation and oxygen-mediated regenerative oxidation of the ferrous chelate CDTA. The remaining two sulfur-bearing compounds, considered not oxidizable by CDTA–Fe(III), undergo only physical absorption in such solutions, so their solubility in aqueous CDTA–Fe(III) alkaline solutions is a crucial parameter for designing the complete scrubbing-absorption process. This investigation was carried out to determine the Henry's law constants of dimethyldisulfide (DMDS) in pure water, in aqueous iron-free CDTA solutions and CDTA–Fe(III) complex solutions using the static headspace method with an estimated accuracy of 2%. Experiments with aqueous solutions of chelate concentrations varying between 38 and 300 mol m⁻³ were carried out at temperatures between 298 and 333 K and atmospheric pressure. It was shown that DMDS solubility decreases with increasing temperature for all systems and is not much influenced by the CDTA concentration and solution pH.     

New approaches to reprocessing of oxide nuclear fuel

Dissolution of UO₂, U₃O₈, and solid solutions of actinides in UO₂ in subacid aqueous solutions (pH 0.9–1.4) of Fe(III) nitrate was studied. Complete dissolution of the oxides is attained at a molar ratio of ferric nitrate to uranium of 1.6. During this process actinides pass into the solution in the form of U(VI), Np(V), Pu(III), and Am(III). In the solutions obtained U(VI) is stable both at room temperature and at elevated temperatures (60 °C), and at high U concentrations (up to 300 mg mL^?1). Behavior of fission products corresponding to spent nuclear fuel of a WWER-1000 reactor in the process of dissolution the simulated spent nuclear fuel in ferric nitrate solutions was studied. Cs, Sr, Ba, Y, La, and Ce together with U pass quantitatively from the fuel into the solution, whereas Mo, Tc, and Ru remain in the resulting insoluble precipitate of basic Fe salt and do not pass into the solution. Nd, Zr, and Pd pass into the solution by approximately 50 %. The recovery of U or jointly U + Pu from the dissolution solution of the oxide nuclear fuel is performed by precipitation of their peroxides, which allows efficient separation of actinides from residues of fission products and iron.     

基于非手性邻苯酚胺衍生物的半醌Fe(III)络合物的镜面对称性破缺及其绝对构型关联

以2- 苯胺基-4,6- 二叔丁基苯酚(H₂L)和FeCl₂·4H₂O为原料制备了一对手性半醌Fe(III) 络合物Λ-mer-[Fe(L^ISQ)₃]和Δ-mer-[Fe(L^ISQ)₃] (L^ISQ: 2-苯亚胺基-4, 6-二叔丁基苯酚, mer: 经式构型), 通过单晶X射线衍射分析结合单晶压制片膜的固体圆二色(CD)光谱确定了该络合物的绝对构型, 在此基础上建立了此类半醌络合物[M(L^ISQ)₃] (M=Cr, Fe, Co)的惟手性金属中心绝对构型与固体CD光谱之间的关联. 此外, 还对10份合成的[Fe(L^ISQ)₃]的大宗产物粉末与单晶的固体CD谱进行了比对分析, 以及对1 份合成产物进行10 次重结晶的固体CD 光谱表征. 研究表明该化合物在结晶过程中发生了镜面对称性破缺(MSB), 对映体过量(ee) 值在15%-100%之间.     

Iron (III) Ion Selective Electrode Based on Dithia 12-Crown-4

An iron (III) ion selective PVC membrane electrode based on 1,7-dithia 12-crown-4 as a neutral carrier was prepared. Monovalent responses with a Nerstian slope of 56+1 mV/decade was observed for the Fe (III) ion-selective electrode within the concentration range 10^?3–10^?5 M Fe (NO₃)₃. The monovalent responses may be attributed to the formation of Fe (OH)₂⁺ or Fe (OH)₂(H₂O)⁺₄ species in aqueous solutions and the absorption of these ions into the PVC electrode membrane. The electrode exhibited good selectivity for Fe (III) in comparison with various alkali, alkali-earth and some heavy metal ions. The effects of the composition of the membrame, addition of STPB (sodium tetraphenyl borate), the concentration of internal solution of the electrode and anions in the test solutions were discussed.     

Spectrophotometric determination of thiocyanate ions in stratal waters

The formation of [FeSCN]²⁺ complex in hydrochloric and sulfuric acid medium was studied by spectrophotometry using iron(III) sulfate and ammonium iron(III) sulfate solutions as reactants. A method for the determination of 10–200 μg SCN^? in 25 mL water solutions containing ammonium iron(III) sulfate in sulfuric acid medium was developed; its determination limit is 2.6 μg (P = 0.99, n = 9). The method was applied for the analysis of model water samples with macro- and micro-component compositions similar to that of water from the Arigol licensed area. Operational control of the accuracy rate was performed by the standard addition method. The developed method can be applied to analyze water samples containing 1–90 mg/L thiocyanate ions.     

Effect of the nature of the salt precursor of an oxide-hydroxide sorbent on the sorption of oxalate ions

Generalizations are made on the effect of the nature of a precursor (the original salt of a metal) on the sorption activity of hydrogels of oxidehydroxides (OHes) towards oxalate ions using the example of an OH obtained by the alkaline hydrolysis of chloride, perchlorate, and sulfate of Fe(III); chloride, sulfate, and nitrate of Al; and nitrate of Zr(IV). It is established that the sorption of C₂O ₄ ^2? on the studied OHes is described by the Langmuir equation. We find that the sorption activity depends on the nature of the precursor: Al₂(SO₄)₃ > Al(NO₃)₃ > AlCl₃ > ZrO(NO₃)₂ > Fe₂(SO₄)₃ > FeCl₃ > Fe(ClO₄)₃.     

Extraction of triply charged metal cations in aqueous phase-separating system antipyrine–sulfosalicylic acid–water

Extraction of macro amounts of triply charged metal cations (0.01–0.05 mol L^?1) in aqueous phase-separating system antipyrine–sulfosalicylic acid–water containing no organic solvent is studied. Optimum conditions for phase separation are established and the influence of the concentrations of the major components, inorganic acids (H₂SO₄, HCl), salting-out agents, and the volume of the aqueous phase on the process in question is determined. It was found that the optimum antipyrine/sulfosalicylic acid ratio in the system was (1.5–2.0): 1.0. The introduction of inorganic salting-out agents causes the volume of the organic phase (0.8–1.8 mL) to increase to 2 mL and more. The extractability series of triply charged metal ions is as follows: Tl > Fe > Sc > In > Ga. It was shown that inorganic salts and hexamine influence the degree of extraction of metal cations and that inorganic acids and water affect the distribution mechanism and the composition of the complexes. The half-extraction pH values (pH₁/₂) of the cations are calculated and correlations between the pH₁/₂ values, the ionic radii of the cations, and the polarization ability of the metal ions are established.

     

Three-dimensional 3d–4f hetero-bimetallic coordination polymers through hydrogen bonds: synthesis,structures and mössbauer spectrum analysis

Four cyano-bridged 3d–4f hetero-bimetallic Ln(III)–Fe(III) assemblies, {[Ln(DMF)₄(H₂O)₃(µ-CN)Fe(CN)₅]· H₂O} _n (Ln?=?Ce (1), Nd (2), Sm (3) and Gd (4); DMF?=?N,N-dimethylformamide), have been synthesized. X-ray crystallographic analysis of both 3 and 4 reveals three-dimensional network structures resulting from hydrogen bonds in the crystals. With respect to the coordination number on Sm(III) atoms, 3 is different from previously reported structures. Structural comparison indicates that the differences in magnetic properties between 3 and 4 do not derive from structural factors. Mössbauer spectra at both 298 and 10?K reveal that the characteristic quadrupole splitting for low-spin Fe(III) ions (S?=?1/2) remains unchanged, indicating that the spin state of Fe(III) ions in 1–4 is not affected by temperature. The magnetic anisotropy derived from the ground states of Ln(III) ions with odd 4f ⁿ electrons (n?=?1, 3, 5 and 7), ²F_5/2,⁴I_9/2, ⁶H_5/2 and ⁸S_7/2 for Ce(III), Nd(III), Sm(III) and Gd(III), respectively, dominates the exchange interaction in the Ln(III)–NC–Fe(III) systems.     

Separation of Mercury with an Ammonium Sulfate‐Ammonium Thiocyanate‐Ethyl Violet Flotation System

The separation behavior of mercury by a flotation system consisting of ammonium sulfate, ammonium thiocyanate and ethyl violet, and the conditions for the separation of Hg(II) with other common metal ions have been studied. The studies show that in aqueous solutions, Hg(II) combines with NH₄SCN and ethyl violet(EV) into dissoluble ternary ion‐association complex [Hg(SCN)4^2?]?(EV)₂. In the presence of ammonium sulfate, the precipitate is floats well on the surface of the water phase and separates from water thoroughly. It shows that Hg(II) can be separated completely from Cd(II), Fe(II), Co(II), Ni(II), Mn(II) and Al(III) by flotation at pH1.0. The flotation mechanism of Hg(II) is described in this paper.     

The enthalpy of formation of magnesium sulfate ion pairs

The enthalpies of dilution of lithium, sodium, potassium, and magnesium chloride and sulfate solutions in the range 0.1 to 1.0 m have been measured at 30°C with a microcalorimeter. The relative apparent enthalpies φ_L of these solutions have been determined with the aid of an extended form of the Debye-Hückel limiting law $$\phi _L = S_H I^{1/2} [1/(1 + I^{1/2} ) - (\sigma /3)] + {\rm B}{\rm I} + CI^{3/2} $$ whereS _H is the limiting-law slope, σ = 3/I^3/2 × [(1+I^1/2 ? 1/(1+I^1/2 ? 2 ln (2+I^1/2)], andB andC are empirical constants. This equation fits the experimental results to within a standard deviation of 2 cal-mole^?1 for all the salts. The measured φ_L for the MgSO₄ solutions were compared to those calculated using the additivity principle, φ_L(MgCl₂) + φ_L(Na₂SO₄) ? 2φ_L(NaCl), and the extended Debye-Hückel equation. The results of this comparison have been used to calculate the ΔH _A ^o for the formation of MgSO ₄ ⁰ . A value of ΔH _A ^o = 1.15 to 1.36 was obtained, depending upon the φ_L estimates for the free ions Mg²⁺ and SO ₄ ^2? . The results are briefly discussed and compared to the results obtained by other workers.     

The Effect of Adsorption of Ions of the Hexacyanoferrate(II)/(III) Redox Pair on Self-Assembly of Octanethiol at Its Adsorption from Aqueous Solutions on Gold Electrode

The effect of components of the redox pair K₃[Fe(CN)₆]/K₄[Fe(CN)₆] on the dynamics of formation of octanethiol (OT) monolayers from aqueous thiol-containing solutions of 0.1 М NaClO₄ is studied by cyclic voltammetry (CVA). The formation of OT monolayers is shown to depend on the presence of ions of hexacyanoferrate(II)/(III) in solution. Being added to solution, the components of the [Fe(CN)₆]^3–/4– redox pair sharply increase the time of formation of the insulating monolayer OT films and make them less stable. The destabilizing and inhibiting action of [Fe(CN)₆]^3–/4– ions becomes stronger as their concentration in solution increases. The adsorption activity of individual components of the redox pair is assessed. The strong and approximately equal adsorption activity of ions [Fe(CN)₆]^3– and [Fe(CN)₆]^4– on gold in the presence of octanethiol is observed. At the same time, OT and the hexacyanoferrate(II)/(III) ions can be placed in the following row: OT > [Fe(CN)6]^3– ≈ [Fe(CN)₆]^4–. Recommendations are given on how to eliminate the interfering action of the K₃[Fe(CN)₆]/K₄[Fe(CN)₆] redox-pair ions when studying the insulating properties of thiol monolayers on gold.     

Evidence of quasi-intramolecular redox reactions during thermal decomposition of ammonium hydroxodisulfitoferriate(III), (NH4)2[Fe(OH)(SO3)2]·H2O

Synthesis of ammonium hydroxodisulfitoferriate(III), (diammonium catena-{bis(μ ²-sulfito-κO,κO)-μ ²-hydroxo-κ²O}ferrate(III) monohydrate) (NH₄)₂[Fe(OH)(SO₃)₂]·H₂O (compound 1) and its thermal behavior is reported. The compound is stable in air. Its thermal decomposition proceeds without the expected quasi-intramolecular oxidation of sulfite ion with ferric ions. The disproportionation reaction of the ammonium sulfite, formed from the evolved NH₃, SO₂ and H₂O in the main decomposition stage of 1, results in the formation of ammonium sulfate and ammonium sulfide. The ammonium sulfide is unstable at the decomposition temperature of 1 (150 °C) and transforms into NH₃ and H₂S which immediately forms elementary sulfur by reaction with SO₂. The formation and decomposition of other intermediate compounds like (NH₄)₂S_nO_x (n = 2, x = 3 and n = 3, x = 6) results in the same decomposition products (S, SO₂ and NH₃). Two basic iron sulfates, formed in different ratios during synthesizing experiments performed under N₂ or in the presence of air, have been detected as solid intermediates which contain ammonium ions. The final decomposition product was proved to be α-Fe₂O₃ (mineral name hematite).

     

Removal of Lead(II), Cadmium(II), and Arsenic(III) from Aqueous Solution Using Magnetite Nanoparticles Prepared by Green Synthesis with Box–Behnken Design

Two types of magnetite (Fe₃O₄) nanoparticles were investigated as adsorbents for the simultaneous removal of Pb(II), Cd(II), and As(III) metal ions from aqueous solution. Magnetite nanoparticles were prepared by two synthesis procedures, both using water as solvent, and are referred to as conventional Fe₃O₄ nanoparticles and green Fe₃O₄ nanoparticles. The latter used Citrus limon (lemon) aqueous peel extract as the surfactant. Box–Behnken experimental design was used to investigate the effects of parameters such as initial concentration (20–150?mg?L^?1), pH (2–9), and biomass dosage (1–5?g?L^?1) on the removal of Pb(II), Cd(II), and As(III) ions. The optimum parameters for removal of the studied metal ions from aqueous solutions, including the initial ion concentration (20?mg?L^?1), pH (5.5) and adsorbent dose (5?g?L^?1), were determined. The pseudosecond-order model exhibited the best fit for the kinetic studies, while adsorption equilibrium isotherms were best described by Langmuir and Freundlich models. The optimum conditions were applied for the treatment wastewater. The removal efficiencies of Pb(II), Cd(II), and As(III) using the conventional and green synthesized Fe₃O₄ nanoparticles were 59.4?±?4.3, 18.7?±?1.9 and 17.5?±?1.6, and 98.8?±?5.6, 46.0?±?1.3, and 48.2?±?2.6%, respectively. These results demonstrate the potential of magnetite nanoparticles synthesized using C. limon peel extract as highly efficient adsorbents for the removal of Pb(II), Cd(II), and As(III) ions from aqueous solution.     

Activation of sulfite by ferric ion for the degradation of 2,4,6-tribromophenol with the addition of sulfite in batches

In this work, the removal of 2,4,6-tribromophenol (TBP) by ferric ion-activated sulfite [Fe(III)/S(IV)] process was systematically investigated with determining the intermediate products and evaluating the influences of some operational conditions and water matrices. Our results show that batching addition of S(IV) benefits the S(IV) utilization efficiency and TBP removal, with SO₄^?? being the primary reactive radical accounting for TBA degradation. The maximum TBP removal in the Fe(III)/S(IV) process was observed at pH 4.0 and oxygen is essential in this process. With increasing Fe(III) and S(IV) dosages from 0.05 and 0.1 mmol/L to 0.2 and 2.0 mmol/L, respectively, TBP removal followed trends of first increase then decrease. As the acute toxicity of the TBP solution was significantly reduced, the Fe(III)/S(IV) process was believed to be a good choice in the treatment of TBP.     

Separation and determination of some trivalent metal ions using rhodamine B grafted polyurethane foam

The incorporation of rhodamine B into polyurethane foam matrix was prepared by mixing the rhodamine B with polyol (polyether) prior to the addition of diisocyanate reagent to form the polyurethane foam material. Rhodamine B grafted polyurethane foam (Rod.B-PUF) was found to be very suitable for the separation and preconcentration of trivalent metal ions e.g. bismuth (III), antimony (III) and iron (III) from thiocyanate solutions. Bismuth and antimony were separated from concentrated acid medium (1–6 M H₂SO₄). Iron (III) was separated from pH 1 to 3. The kinetics of sorption of the Bi (III), Sb (III) and Fe (III) onto the Rod.B-PUF was found to be fast, the extraction is accomplished from 5 to 10 min with average values of half-life of sorption (t_1/2) of 2.9 min. The average values of the Gibbs free energy (ΔG) for the sorption of metal ions onto Rod.B-PUF are ?6.6 kJ mol^?1, which reflect the spontaneous nature of sorption process. The sorption mechanism of the metal ion onto Rod.B-PUF was also discussed.     

Thin-layer chromatography of inorganic ions on polyethyleneimine cellulose in sulfuric acid and acid-ammonium sulfate media

Summary The thin-layer chromatographic behavior of 49 inorganic ions on polyethyleneimine (PEI) cellulose, a weakly basic anion-exchanger, has been systematically studied in sulfuric acid and ammonium sulfate media (both 0.01–1.0 moldm⁻³). The sorption on the cellulose decreases with increasing concentration of the acid or sulfate for most of the ions and to a lesser extent for Hg(II), Bi(III), Th(IV), Nb(V), and U(VI). The R_f values of Pd(II), Ru(III), Au(III), Pt(IV), and Ta(V) are extremely low in both systems. Ba(II), Pb(II), Sb(III), Mo(VI), and W(VI) are also strongly retained on the layer. Oxy-anions such as As(III) and Se(VI) are not adsorbed on the cellulose to any great extent, but Re(VII) distributes on the plate with a R_f value of about 0.5. The characteristic retention on PEI-cellulose layer of several polyvalent ions, which form anionic sulfato complexes, can be observed in ammonium sulfate media. Possibilities for separations of analytical interest are also demonstrated in both systems.     

Dimere low-spin Eisen(III)-Phthalocyanine: Synthese und Eigenschaften ferromagnetisch gekoppelter μ-Oxodi(acidophthalocyaninatoferrate(III))

Dimeric Low-Spin Iron(III) Phthalocyanines: Synthesis and Properties of Ferromagnetically Coupled μ-Oxodi(acidophthalocyaninatoferrates(III)) μ-Oxodi(phthalocyaninatoiron(III)) ([(FePc^2?)₂O]) dissolved in pyridine reacts with different Tetra(n-butyl)ammonium salts yielding partly solvated Di(tetra(n-butyl)ammonium)-μ-oxodi(acidophthalocyaninatoferrates(III)) ((ⁿBu₄N)₂[(Fe(X)Pc^2?)₂O]; X^? = CN^?, Im^?, NCO^?, NCS^?, NO₂^?). The uv-vis. spectra show the typical B, Q, N and L regions of the Pc^2? ligand scarcely influenced by the axial ligands X. In comparison with [(FePc^2?)₂O] mainly the B region is hypsochromically shifted due to strong excitonic coupling (> 3 kK). Two regions of weak absorbance at ca. 7.6–8.7 and 11.4–13.0 kK are assigned to trip-doublet transitions. The m.i.r. and resonance Raman spectra are dominated by the fundamental vibrations of the Pc^2? ligand being characteristic for hexa-coordinated low-spin Fe^III phthalocyanines. Internal vibrations of the ambident axial ligands X are in accordance with the proposed Fe? X bond. The i.r. active asym. (Fe? O? Fe) stretching vibration is observed in the region 631–690 cm^?1. Fe? X stretching vibrations are only present in the f.i.r. spectra. The magnetic properties and Mößbauer spectra are interpreted in terms of an electronic model which assumes that a S′ = 1 ground state arises from strong ferromagnetic coupling of the low-spin Fe^III centres. Both spin-Hamiltonian and ligand-field models have been employed to fit the variable temperature susceptibility data. These low-spin μ-oxo Fe^III dimers are rare compared to the many known examples of coupled high-spin species including the parent, [(FePc^2?)₂O].