Photocatalytic degradation of trichloroethylene on platinum ion-doped TiO<Subscript>2</Subscript> under visible light irradiation

Porous platinum ion-doped TiO₂ (Pt–TiO₂) was prepared by a sol–gel method and demonstrated to have superior photocatalytic activity for the photodegradation of gaseous trichloroethylene (TCE) under visible light (VL) irradiation from a xenon lamp equipped with 422-nm cut-off filter. Kinetic studies were performed to clarify the effect of the doping amounts, space times, VL intensity, and mole fractions of TCE, O₂, and H₂O on the degradation of TCE. Under ultraviolet (UV) irradiation, the photocatalytic activity of Pt–TiO₂ was the same as that of TiO₂, indicating that the doped Pt ion did not act as a recombination center for the photogenerated holes and electrons. Based on the kinetic data and reaction products, we conclude that the photocatalytic degradation of TCE on Pt–TiO₂ under VL irradiation proceeds similarly to TiO₂ under UV irradiation. We also performed the photocatalytic degradation of TCE at the space time of 7.5 × 10⁷ g s mol^?1 in a tubular reactor packed with the Pt–TiO₂ pellets which are more suitable than the Pt–TiO₂ powder for the practical remediation of the contaminated gas. TCE was completely degraded, i.e. 100% conversion was achieved under VL irradiation but only a small quantity of CO₂ was formed with the stoichiometric ratio of [CO₂]_formed/[TCE]_degraded of ca. 0.33. By switching the gas stream containing TCE to humid air, more CO₂ was formed, indicating that the dichloroacetates accumulated on the Pt–TiO₂ surface are photodegradable to CO₂ under VL irradiation.     

Photocatalytic degradation of trichloroethylene over BiOCl under UV irradiation

In this study, BiOCl samples were synthesized under different pH values and characterized by XRD, SEM, UV‐vis DRS, BET, photoelectrochemical measurement and PL. The photocatalytic performances of the as‐prepared samples were evaluated through the decomposition of trichloroethylene (TCE) under UV irradiation. The influences of several parameters such as solution pH and common inorganic anions on TCE removal were investigated. Results indicated that BiOCl‐0.6 exhibited better photocatalytic performance than BiOCl‐6.0 because of its higher migration ability of photo‐induced carrier. The photocatalytic degradation of TCE over BiOCl‐0.6 followed pseudo first‐order kinetics and appeared to be more efficient in acidic solution than in alkaline. TCE was almost completely dechlorinated in 120 minutes. The inhibiting effect of naturally occurring anions was in the order of HCO₃^‐ >SO₄^2‐ >NO₃^‐, while Cl^‐ exhibited a dual effect. Moreover, BiOCl‐0.6 exhibited superior reusability after three cycles of repetition tests.     

Photocatalytic degradation of trichloroethylene using N-doped TiO<Subscript>2</Subscript> prepared by a simple sol–gel process

Visible-light-driven N-doped TiO₂ was prepared by a simple sol–gel process using nitric acid not only as the acid catalyst of the sol–gel reaction but also as the source of nitrogen. The photocatalytic performance of the N-doped TiO₂ was investigated by using FTIR spectroscopy to monitor the degradation of trichloroethylene (TCE) during UV and visible irradiation. The photocatalytic degradation of TCE was well-reproduced several times. The activity of Ti–O–N species was supported experimentally. The N-doped TiO₂ was found to be responsive to visible light and was stable during repeated runs and maintained the nitrogen species and its activity for at least four months.     

Synthesis of immobilized TiO2 nanowires by anodic oxidation and their gas phase photocatalytic properties

In this paper, anodic oxidation method was successfully employed to the direct growth of immobilized TiO₂ nanowires on titanium foil in ethylene glycol electrolyte solution contained HF and water. The morphologies of the TiO₂ nanowires could be tuned by changing the content of HF and water. The structures, morphologies and optical properties of TiO₂ nanowires were characterized by SEM, XRD, UV–vis and PL. It was found that the nanowires originally grew from the splitting of TiO₂ nanotubes. The gas phase photocatalytic activities were investigated by photodegradation of gaseous toluene under UV irradiation, and irregular TiO₂ nanowires showed the best photocatalytic ability.     

SnO2/TiO2纳米管复合光催化剂的性能及失活再生

基于微波水热法和微乳液法合成SnO₂/TiO₂纳米管复合光催化剂. 通过X射线衍射（XRD）、配有能量色散X射线光谱仪（EDX）的透射电镜（TEM）和电化学手段对光催化剂进行表征. 以甲苯为模型污染物,考察光催化剂在紫外光（UV）和真空远紫外光（VUV）下的性能及失活再生. 结果表明,SnO₂/TiO₂纳米管复合光催化剂形成三元异质结（锐钛矿相TiO₂（A-TiO₂）/金红石相TiO₂（R-TiO₂）、A-TiO₂/SnO₂和R-TiO₂/SnO₂异质结）,促使光生电子-空穴对的有效分离,提高光催化活性. SnO₂/TiO₂表现出最佳的光催化性能,UV和VUV条件下的甲苯降解率均达100%,CO₂生成速率（k₂）均为P25的3倍左右. 但由于UV光照矿化能力不足,中间产物易在催化剂表面累积. 随着UV光照时间的增加,SnO₂/TiO₂逐渐失活,20 h 后k₂由138.5 mg·m^-3·h^-1下降到76.1 mg·m^-3·h^-1. 利用VUV再生失活的SnO₂/TiO₂,过程中产生的·OH、O₂^-·、O（¹D）、O（³P）、O₃等活性物质可氧化吸附于催化剂活性位的难降解中间产物,使催化剂得以再生,12 h后k₂恢复到143.6 mg·m^-3·h^-1. UV和VUV的协同效应使UV降解耦合VUV再生成为一种可持续的光催化降解污染物模式.     

Photocatalytic degradation of dichloroacetyl chloride adsorbed on TiO<Subscript>2</Subscript>

Dichloroacetyl chloride (DCAC) attracted our attention as an intermediate product of the photocatalytic degradation of trichloroethylene (TCE). The adsorption and photocatalytic reaction of DCAC on TiO₂ have been investigated by FTIR spectroscopy. The influence of the surface structure of several TiO₂s on the reaction mechanism was discussed in order to understand the complete degradation mechanism of TCE as well as DCAC. DCAC was transformed into dichloroacetic acid (DCAA) on the relatively hydrophobic TiO₂ surface by the small amount of the water molecules weakly adsorbed on the surface. This DCAA was degraded to phosgene, CO₂, and CO during UV irradiation. For the hydrophilic TiO₂, DCAC was mainly transformed into the dichloroacetate anion. UV irradiation allowed this species to produce chloroform in addition to phosgene, CO₂, and CO. It is suggested that DCAC easily reacts with the Ti–OH group on the hydrophilic TiO₂ and forms the bidentate titanium chelate of dichloroacetate, which efficiently degrades into chloroform.     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附-脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

Synthesis and Characterization of TiO2/YFeO3 and Its Photocatalytic Oxidation of Gaseous Benzene

YFeO₃ was prepared by coprecipitation method and citric acid method, and TiO₂/YFeO₃ heterosystem photocatalysts were synthesized by loading TiO₂ sol on the surface of YFeO₃via sol-gel method. Their photocatalytic activities were evaluated by the decomposition of gaseous benzene under UV light illumination. The prepared photocatalysts were characterized by nitrogen adsorption-desorption, X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and UV-Vis diffuse reflectance spectroscopy. Results revealed that the heterosystem photocatalysts prepared by coprecipitation method showed higher activity, and the maximum conversion of benzene could reach 44.7% within 180 min. The YFeO₃ samples prepared from coprecipitation method and citric acid method were absolutely in orthorhombic phase. The deposited titania was dispersed on the surface of carrier and a certain interaction existed between TiO₂ and YFeO₃. The two heterosystems photocatalysts had narrow band-gap energies.     

Photo Catalytic Degradation of Azo Dyes over Mn2+ Doped TiO2 Catalyst under UV/Solar Light:An Insight to the Route of Electron Transfer in the Mixed Phase of Anatase and Rutile

Mn²⁺ ion was doped into the TiO₂ matrix and its photocatalytic activity was evaluated for the degradation of a mono azo dye methyl orange (MO) and a di‐azo dye brilliant yellow (BY) under UV/solar light. X‐ray diffraction results revealed the phase transformation from anatase to rutile due to the inclusion of Mn²⁺ ion into the TiO₂ matrix. All the doped catalysts showed a red shift in the band gap to the visible region. The degradation reaction of the dyes was found to be dependent on its structure. It was found that mono azo dye degrades faster than di azo dye under UV/solar light. The rate constant under identical conditions calculated for the degradation of MO is 2.4 times (under UV light) and 4.5 times (under solar light) higher compared to BY. Among the photocatalysts studied, Mn²⁺(0.06 at.%)‐TiO₂ showed higher activity under both UV and solar light illumination. The synergestic effect in the bicrystalline framework of anatase and rutile effectively suppresses the charge carrier recombination and enhances the photocatalytic activity. The degradation reaction was followed by UV‐visible spectroscopy and the photoproducts formed were analyzed by GC‐MS techniques.     

Mass spectrometry on-line monitoring and MS2 product characterization of TiO2/UV photocatalytic degradation of chlorinated volatile organic compounds

On-line Mass Spectrometry and MS² are applied to monitor and identify the by-products and total mineralization products of TiO₂/UV photocatalytic degradation of four chlorinated volatile organic compounds (VOCs): trichloroethylene (TCE), tetrachloroethylene (TeCE), chloroform, and dichloromethane. Selected multiple ion mass spectrometry monitoring using characteristic 70 eV electron ionization ionic fragments monitors in real time the destruction of the starting VOC and the formation of by-products, i.e., the degrees of VOC mineralization, as a function of the flow and relative humidity of the carrier gas (synthetic air). Several by-products were detected: phosgene for TCE, TeCE, and chloroform; dichloroacetyl chloride for TCE; and trichloroacetyl chloride for TeCE. Cl₂ and CO₂ were also detected as final mineralization products of the four chlorinated VOCs. Structural characterization of by-products was accomplished via MS² collision-induced dissociation of molecular ions or characteristic ionic fragments.     

多孔超薄g-C3N4纳米片负载Pt复合材料的制备及其光催化性能

以三聚氰胺为前驱体,通过热氧化刻蚀法制备多孔超薄g-C₃N₄纳米片（CNHS）,将其与氯铂酸钾溶液混合后采用原位光化学还原法成功制备了CNHS负载Pt光催化剂（Pt-CNHS）。使用粉末X射线衍射、场发射扫描电子显微镜、X射线光电子能谱、透射电子显微镜、紫外可见漫反射光谱和N₂吸附-脱附测试等技术对所制备样品的结构、形貌、光吸收特性、光电化学性能和比表面积等进行系统分析。并以气相甲苯为目标降解物,研究其光催化性能。结果表明,相对于体相g-C₃N₄（CNB）和CNHS,Pt的引入可以有效增强催化剂对可见光的吸收能力、响应范围及载流子分离效率。与纯g-C₃N₄和CNHS相比,Pt-CNHS在紫外和可见光照射下均表现出更高的光催化降解气相甲苯的活性。此外,也对Pt-CNHS光催化剂在可见光照射下降解气相甲苯的反应历程做了初步研究。     

球磨法制备Y3+/TiO2光催化剂及处理海水养殖废水

采用机械球磨法制备Y~(3+)修饰TiO_2光催化剂,利用紫外-可见漫反射光谱(UV-Vis DRS)、X射线光电子能谱(XPS)、X射线粉末衍射(XRD)、扫描电镜(SEM)等对其进行表征,在紫外光下,以亚甲基蓝(MB)为去除物来考察催化剂活性并优化球磨工艺。将最佳条件下制得的Y~(3+)/TiO_2光催化剂负载于不同半径的塑料浮球上,分别在紫外光和模拟太阳光照射下处理海水养虾废水,通过CODCr(chemical oxygen demand)及三维荧光观察有机物含量变化。结果表明,当Y~(3+)的物质的量分数为2%,球磨时间4 h,球料质量比4∶1,转速为500 r·min~(-1)时,MB光催化降解反应速率常数可达0.111 3 min~(-1),是纯TiO 2的4.2倍。由UV-Vis DRS、XPS、N_2吸附-脱附、XRD、SEM等表征结果显示,2%Y~(3+)/TiO_2样品的禁带宽度降低至3.05 eV,光吸收发生红移,并产生可见光响应,表面吸附氧含量明显增加,比表面积增大到104 m~2·g~(-1)。采用纯TiO_2及2%Y~(3+)/TiO_2为光催化剂处理养虾废水,在可见光和紫外光下CODCr的去除率分别为14.7%和18.8%、26.9%和37.5%。考察3种直径分别为1、2、3 cm负载Y~(3+)/TiO_2浮球的光催化效果,显示直径为2 cm浮球效果最佳,CODCr去除率可达38.5%。     

Template‐free Fabrication of ZnS/TiO2 Photocatalyst with Macrochannels

Constructing a porous structure in photocatalysts is an effective strategy for improving the photocatalytic activity because of its enhanced molecule transfer capability and light capturing efficiency. In this work, a hierarchical macro‐/mesoporous ZnS/TiO₂ composite with macrochannels was successfully synthesized without using templates by the simple dropwise addition of an ethanol solution of tetrabutyl titanate and zinc acetate into a sodium sulfide aqueous solution, which was then calcined at 450°C. Compared with pure TiO₂, the ordered porous ZnS/TiO₂ composite exhibited an enhanced photocatalytic activity on methylene blue removal under UV‐light irradiation. The results indicate that the macro‐/mesoporous structure, the large specific surface area, and the heterostructure combination between ZnS and TiO₂ play a synergistic effect on the enhanced photocatalytic activity via improving the light absorption and the diffusion of organic molecules, providing more reactive sites for the photocatalytic reaction and improving the separation of photogenerated electron–hole pairs, respectively. Radical trapping experiments demonstrated that holes (h⁺) and superoxide anion radicals (O₂⁻) play an important role in the photocatalytic oxidation process.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.