Comparative study of the sol–gel based solid phase microextraction fibers in extraction of naphthalene, fluorene, anthracene and phenanthrene from saffron samples extractants

We are introducing a method for the determination of some polycyclic aromatic hydrocarbons in aqueous saffron sample by direct immersion solid phase microextraction (SPME) and gas chromatography. A sol–gel technique is used for the preparation of the SPME fibers. Three kinds of sol–gel coatings on the fibers were tested and compared. They are composed of poly(dimethyl siloxane) (PDMS), poly(ethylene glycol) (PEG), and a poly(ethylene glycol) modified with multi-walled carbon nanotubes (PEG/CNTs). The effects of fiber coating, desorption time, desorption temperature, extraction time, stirring speed and salting effect were optimized. Under the optimal conditions, the detection limits (at S/N?=?3) are 7–50, 5–50, and 1–10?pg?mL^–1, respectively, for SPME fibers made from PDMS, PEG and PEG/CNTs. The relative standard deviations for one type of fiber are from 2.1% to 9.6% for all fibers (at n?=?5), and in the range from 1.9% to 9.8% from batch to batch (for n?=?3).

Solid-phase microextraction of Methylene Blue using carboxy graphene-modified steel wires, and its detection by electrochemiluminescence

We report on a new solid phase for microextraction (SPME) of Methylene Blue (MB). It was obtained by immobilizing carboxy graphene (G-COOH) on a stainless steel wire. Scanning electron micrography showed the surface to be homogeneous, porous and wrinkled. The effects of sample solution pH, extraction time, stirring rate, desorption time and of desorption solvent on the efficiency of extraction of MB were optimized. The new SPME was coupled to electrochemiluminescence detection of MB and gave a linear analytical range from 2.7 nM to 1.3 μM, and the detection limit is 0.89 nM which is better than other methods. When considering the enrichment factor of ~20, the resulting detection limit is estimated to be 45 pM. The new SPME fiber was successfully applied to the analysis of MB in spiked real water samples. Recoveries range from 95.7 % to 113.0 %, and relative standard deviations are <5.0 %, which showed the good reproducibility of the method.

An inorganic–organic hybrid material based on ZnO nanoparticles anchored to a composite made from polythiophene and hexagonally ordered silica for use in solid-phase fiber microextraction of PAHs

We report on an inorganic–organic hybrid nanocomposite that represents a novel kind of fiber coating for solid-phase microextraction (SPME) of polycyclic aromatic hydrocarbons (PAHs). The material is composed of ZnO nanoparticles, polythiophene and hexagonally ordered silica, and displays good extraction capability due to its nanostructure. The nanocomposite was synthesized by an in-situ polymerization technique, and the ZnO nanoparticles were anchored to the pores in the walls. The ZnO/polythiophene/hexagonally ordered silica (ZnO/PT/SBA-15) nanocomposite was then deposited on a stainless steel wire to obtain the fiber for SPME of PAHs. Optimum conditions include an extraction temperature of 85 °C (for 30 min only), a desorption temperature of 260 °C (for 2 min), and a salt concentration (NaCl) of 20 % (w/v). The detection limits are between 8.2 and 20 pg mL^?1, and the linear responses extend from 0.1 to 10 ng mL^?1. The repeatability for one fiber (for n?=?5), expressed as relative standard deviation, is between 4.3 and 9.1 %. The method offers the advantage of being simple to use, rapid, and low-cost (in terms of equipment). The thermal stability of the fiber and high relative recovery (compared to conventional methods) represent additional attractive features.

Ultrasound-assisted emulsification–microextraction for the sensitive determination of ethyl carbamate in alcoholic beverages

A method based on ultrasound-assisted emulsification–microextraction (USAEME) was proposed in this contribution for the determination of ethyl carbamate (EC) in alcoholic beverages using gas chromatography coupled to triple quadrupole mass spectrometry. To achieve the determination of EC in alcoholic beverages, the influences on the extraction efficiency of type and volume of extraction solvent, temperature, ionic strength, alcohol content, and extraction time were studied, once the extraction solvent had been selected. The optimized conditions were 200.0 μL of chloroform at 30 °C during 5 min with 15 % (m/v) sodium chloride addition. The detection limit, relative standard deviations, linear range, and recoveries under the optimized conditions were 0.03 μg L^?1, 4.2–6.1 %, 0.1–50.0 μg L^?1, and 80.5–87.9 %, respectively. Moreover, the feasibility of the present method was also validated by real samples. To the best of our knowledge, this is the first time that USAEME has been applied to determine a strongly hydrophilic compound in alcoholic beverages.

One-pot microwave-assisted solvent-free synthesis,theoretical and experimental studies on barrier rotation of C–N bond of N-alkenyl-1,2,3-triazoles

The reactions on benzotriazoles continue to happen to reach interesting varieties of their derivatives. This study reports a fast one-pot microwave-assisted solvent-free synthesis of N-alkenyl-1,2,3-benzotriazole (3, 5, and 7) and 1-(2-Alkyloxycarbonyl-vinyl)-1H-[1–3] triazole-4-carboxylic acid methyl ester (8 and 9) derivatives by nucleophilic addition reactions of 1,2,3-benzotriazole (C₆H₅N₃) (1) and 1H-[1–3] triazole-4-carboxylic acid methyl ester (C₄H₄N₃O₂) (1′) with R-propiolates (R = Me, Et; 2 & 4) and phenylacetylene 6 in good yields. The values of activation energy for rotation around C–N bond in the synthesized N-alkenyl-1,2,3-triazole compounds were studied by DFT-B3LYP/6-31G* method.     

Theoretical study on the mechanism of C2Cl3 + NO2 reaction

The radical-molecule reaction of C₂Cl₃ with NO₂ is explored at the B3LYP/6-311G(d,p) and CCSD(T)/6-311+G(d,p) (single-point) levels. On the singlet potential energy surface (PES), the association between C₂Cl₃ and NO₂ is found to be carbon-to-nitrogen attack forming the adduct C₂Cl₃NO₂ (1) without any encounter barrier, followed by isomerization to C₂Cl₃ONO (2). Starting from 2, the most feasible pathway is the N–O1 bond cleavage which lead to P ₁ (C₂Cl₃O + NO). Much less competitively, 2 transforms to the three-membered ring isomer c-OCCl₂C–ClNO (4 ^a ) which can easily interconvert to c-OCCl₂C–ClNO 4 ^b . Then 4 (4 ^a , 4 ^b ) takes direct C1–C2 and C2–O1 bonds cleavage to give P ₂ (COCl₂ + ClCNO). The lesser competitive channel is the 4 ^a isomerizes to the four-membered ring intermediate O-c-CNClOCCl₂ (5) followed by dissociation to P₃ (CO + ClNOCCl₂). The concerted 1,2-Cl shift along with C1–O1 bond rupture of 4 ^b to form ONC(O)CCl₃ (6) followed by dissociation to P ₄ (ClNO + OCCCl₂) is even much less feasible. Moreover, some of P ₃ and P ₄ can further dissociate to P ₅ (ClNO + CO + CCl₂). Compared with the singlet pathways, the triplet pathways may have less contribution to the title reaction. Our results are in marked difference from previous theoretical studies which showed that two initial adducts C₂Cl₃–NO₂ and C₂Cl₃–ONO are obtained. Moreover, in the present paper we focus our main attentions on the cyclic isomers in view of only the chain-like isomers are considered by previous studies. The present study may be helpful for understanding the halogenated vinyl chemistry.     

Fibers coated with a graphene-polyaniline nanocomposite for the headspace solid-phase microextraction of organochlorine pesticides from seawater samples

We have prepared a fiber for solid-phase microextraction of organochlorine pesticides. A graphene-polyaniline composite was electrochemically deposited on a platinum fiber by exploiting the unique properties of polyaniline and graphene. The modified fiber displays thermal stability up to 320 °C and can be used more than 70 times. It possesses high extraction efficiency due to the high specific surface of graphene. The Pt fiber was used for the extraction and subsequent GC determination of the pesticides heptachlor, aldrin, endrin and p,p’-DDT in aqueous samples. The effects of extraction time, extraction temperature, stirring rate, salinity and headspace volume were optimized. Calibration plots are linear (with an R² of 0.990) in the 0.2 to 250 μg L^–1 concentration range, and the limits of detection are below 11 ng L^–1 (at an S/N of 3). The relative standard deviations for three replicate measurements with a single fiber were <11.0 %. The recovery of the pesticides from spiked seawater samples ranged from 81 % to 112 %.

Extraction behavior of copper(II) ion with a hydrophobic amino-functionalized ionic liquid

We have prepared the hydrophobic amino-functionalized ionic liquid (IL) 1-(2-aminoethyl)-3-butylimidazolium hexafluorophosphate and investigated its extraction behavior for copper(II) ion as a model cation. The IL, due to the presence of an amino group, is capable of complexing Cu(II) in a ratio of 6:1. The parameters affecting the extraction efficiency were optimized. The IL-based liquid–liquid microextraction was successfully applied to the analysis of Cu(II) in an environmental water standard reference material. The results are promising in terms of liquid–liquid microextraction, separation, and preconcentration of Cu(II).

Synthesis and characterization of glycol-modified vanadium(V) oxoisopropoxide and their oximato derivatives: sol–gel transformations of [VO(OPr i )3], [VO{OCH2CH2OCH2CH2O}{OPr i }] and [VO{OCH2CH2OCH2CH2O}{ON=C(CH3)(C4H3S-2)}] to vanadia

Reaction of [VO(OPr ⁱ )₃] (1) with [O(CH₂CH₂OH)₂] in 1:1 molar ratio in anhydrous benzene yield glycol-modified precursor, [VO{OCH₂CH₂OCH₂CH₂O}{OPr ⁱ }] (2). Further reactions of (2) with internally functionalized oximes in anhydrous benzene yield heteroleptic complexes of the type [VO{OCH₂CH₂OCH₂CH₂O}{ON=C(R)(Ar)}] (3–8) {where R=CH₃, Ar=C₄H₃O-2 (3), C₄H₃S-2 (4), C₅H₄N-2 (5); and when R=H, Ar=C₄H₃O-2 (6), C₄H₃S-2 (7), C₅H₄N-2 (8)}. All these derivatives have been characterized by elemental analyses, molecular weight measurements and spectroscopic techniques. The crysoscopic molecular weight measurement as well as FAB mass study suggests dimeric nature of (2). However, FAB mass spectrum of (4), and the crysoscopic molecular weight measurements of (3), (4), (5) and (6) indicate the monomeric behavior of the oximato derivatives (3–8). Hexa-coordination around vanadium(V) has been proposed for both monomeric and dimeric derivatives. Sol–gel transformations of (1), (2) or (4) to vanadia [(a), (b) or (c), respectively] have been carried out at low sintering temperature (600 °C). The XRD patterns of (a), (b) or (c) indicate formation of a single orthorhombic phase in all the three cases. The SEM images suggest grain like [for (a) and (b)] and rod like [for (c)] morphology of the crystallites. IR, Raman spectra as well as EDX analyses indicate formation of pure vanadia. Absorption spectra of the vanadia (b) and (c) suggest energy band gaps of 2.53 and 2.65 eV, respectively.     

Determination of organochlorine pesticide residues in rice by gas chromatography-mass spectrometry following directly suspended droplet microextraction

A simple and efficient approach as directly suspended droplet microextraction (DSDME) was applied to the determination of organochlorine pesticides in rice prior to analysis by gas chromatography-mass spectrometry (GC-MS). The extraction parameters such as organic solvent type and volume, extraction time, and ion strength were systemically optimized. Furthermore, method linearity, recovery, limits of detections (LODs), and precision were also investigated. The proposed method provided good linearity (R ² = 0.9900–0.9996). LODs determined by GC-MS in selected-ion monitoring (SIM) mode were between 0.0005–0.033 mg/kg. The relative standard deviations (RSDs) varied from 2.0–14.0%, while the enrichment factors were between 221–550. The experimental results suggest that DSDME followed by GC-MS is a simple, sensitive, low-cost and little solvent consumption for the determination of organochlorine pesticides in rice, and has high enrichment factors suitable to trace analysis.     

Multiple stage pentaquadrupole mass spectrometry for generation and characterization of gas-phase ionic species. The case of the PyC2H 5 +· isomers

Eleven isomers with the PyC₂H ₅ ^+· composition, which include three conventional (1–3) and eight distonic radical cations (4–11), have been generated and in most cases successfully characterized in the gas phase via tandem-in-space multiple-stage pentaquadrupole MS² and MS³ experiments. The three conventional radical cations, that is, the ionized ethylpyridines C₂H₅-C₅H₄N^+· (1–3), were generated via direct 70-eV electron ionization of the neutrals, whereas sequences of chemical ionization and collision-induced dissociation (CID) or mass-selected ion-molecule reactions were used to generate the distonic ions H₂C^·?C₅H₄N⁺?CH₃ (4–6), CH₃?C₅H₄N⁺?CH ₂ ^· (7–9), C₅H₅N⁺?CH₂CH ₂ ^· (10), and C₅H₅N⁺?CH^·?CH₃ (11). Unique features of the low-energy (15-eV) CID and ion-molecule reaction chemistry with the diradical oxygen molecule of the isomers were used for their structural characterization. All the ion-molecule reaction products of a mass-selected ion, each associated with its corresponding CID fragments, were collected in a single three-dimensional mass spectrum. Ab initio calculations at the ROMP2/6–31G(d, p)//6–31G(d, p)+ZPE level of theory were performed to estimate the energetics involved in interconversions within the PyC₂H₅ ^+· system, which provided theoretical support for facile 4?7 interconversion evidenced in both CID and ion-molecule reaction experiments. The ab initio spin densities for the a-distonic ions 4–9 and 11 were found to be largely on the methylene or methyne formal radical sites, which thus ruled out substantial odd-spin derealization throughout the neighboring pyridine ring. However, only 8 and 9 (and 10) react extensively with oxygen by radical coupling, hence high spin densities on the radical site of the distonic ions do not necessarily lead to radical coupling reaction with oxygen. The very typical “spatially separated” ab initio charge and spin densities of 4–11 were used to classify them as distonic ions, whereas 1–3 show, as expected, “localized” electronic structures characteristic of conventional radical ions.     

Determination of nickel using cold-induced aggregation microextraction based on ionic liquid followed by flame atomic absorption spectrometry

Cold-induced aggregation microextraction (CIAME) combined with flame atomic absorption spectrometry (FAAS) was applied to preconcentration and determination of nickel(II) ions in natural water samples. The proposed method used 1-hexyl-3-methylimidazolium hexafluorophosphate ([Hmim][PF ₆ ]) as the extraction solvent and 1-(2-thiazolylazo)-2-naphthol (TAN) as the complexing agent. The extraction solvent was dissolved in the sample solution at 45°C. After dissolving, the solution was cooled in the ice bath and a cloudy solution of IL fine droplets was formed due to the decrease of IL solubility. After centrifugation, the fine droplets of extractant phase were settled at the bottom of the conical-bottom centrifuge tube. Analysis was carried out by a FAAS. Several important parameters influencing the CIAME extraction efficiency such as pH, complexing agent concentration, extraction solvent volume, salt effect, solution temperature, extraction time, centrifugation time and heating time were investigated and optimized. Under the optimum conditions, the limit of detection (LOD) was 0.8 ng/mL, and the relative standard deviation (RSD) was 3.4% for 50 ng/mL of nickel. The performance of the method was evaluated for extraction and determination of nickel in tap, mineral and seawater samples, and satisfactory results were obtained.     

Aromatic stability energy studies on five-membered heterocyclic C4H4M (M = O, S, Se, Te, NH, PH, AsH and SbH): DFT calculations

Energetic, geometric and magnetic criteria were applied to examine the stability and/or aromatic character for the cyclic molecules C ₄ H ₄ M (M = O, S, Se, Te, NH, PH, AsH and SbH) at B3LYP/6-311++G^** and MP2/6-311++G^** levels of theory. The isodesmic reactions and nuclear independent chemical shifts (NICS) calculations were utilized to examine the molecules for energetic and magnetic criteria, respectively. The isodesmic reaction energies reveal that thiophene (C ₄ H ₄ S, ?23.269 kcal/mol) and pyrrole (C ₄ H ₄ NH, ?20.804 kcal/mol) have the greatest aromatic stabilization energies and tellurophene (C ₄ H ₄ Te, ?15.114 kcal/mol) and stibole (C ₄ H ₄ SbH, ?1.169 kcal/mol) have the lowest aromatic stabilization energies in their corresponding groups at MP2/6-311++G^**. The NICS calculations confirmed the results obtained through isodesmic reaction energies.     

A strategy to enhance the thermal stability of a nanostructured polypyrrole-based coating for solid phase microextraction

We report on a nanostructured self-doped polypyrrole (SPPy) film that was prepared by an electrochemical technique in an electrolyte containing fluorosulfonic acid as the sulfonation reagent. The film was applied as a new fiber material for solid-phase microextraction (SPME) of the pesticides lindane, heptachlor, aldrin, endosulfans I and II prior to their quantitation by GC with electron capture detection. The SPPy nanoparticles have a diameter of <100?nm. The introduction of covalently bound sulfo groups into the backbone of the polymer resulted in improved temperature resistance (~350?°C) and satisfactory extraction efficiency. The thermal stability of the SPPy fiber is superior to common polypyrrole fibers. Extraction was optimized by means of the Taguchi orthogonal array experimental design with an OA₁₆ (4⁵) matrix including extraction temperature, extraction time, salt concentration, stirring rate, and headspace volume. The method displays good repeatability (RSD?<?6%) and linearity (in the range from 0.78 to 100?ng?mL^?1; with an R² of >0.998. The detection limits are <0.23?ng?mL^?1. The method was successfully applied to the analysis of the pesticides in skimmed milk and fruit juice samples, and recoveries are from 84?±?1 to 105?±?1%.

Theoretical studies on electronic structures and spectroscopic properties of a series of novel β-diketonate Os(II) complexes

The geometries, electronic structures, and spectroscopic properties of a series of [Os^(II)(CO)₃(tfa)(acac(X)₂)] (tfa = trifluoroacetate; acac = acetoylacetonate; X = H (1), CF₃ (2), C₆H₅ (3), and C₁₀H₇ (4)) complexes have been investigated theoretically. The ground and excited state geometries were optimized at the B3LYP/LANL2DZ and CIS/LANL2DZ levels, respectively. The optimized geometry structural parameters agreed well with the corresponding experimental results. As indicated in this paper, the highest occupied molecular orbitals were dominantly localized on the Os atom, ctfa (abbv. of CO and tfa), and acac ligand for 1 and 2, acac ligand and X substituent for 3 and 4, while the lowest unoccupied molecular orbitals were mainly composed of acac ligand and X substituent. Under the time-dependent density functional theory (TDDFT) level with the polarized continuum model (PCM), the absorption and phosphorescence in CH₂Cl₂ media were calculated based on the optimized ground- and excited-state geometries, respectively. The calculated results show that the lowest energy absorptions at 317 (1), 342 (2), 377 (3), and 420 nm (4) are attributed to a change of ππ*/MLCT mixing transition to pure ππ* transition for 1–4, while their phosphorescence emission have similar transition properties. This indicates that the absorption and emission transition characters could be altered by adjusting the π electron-donating ability.     

LC Method for Analysis of Three Flavonols in Rat Plasma and Urine after Oral Administration of Polygonum aviculare Extract

A high-performance liquid chromatographic method has been developed for the simultaneous analysis of the flavonols myricitrin (1), avicularin (2), and juglanin (3) in rat plasma and urine after oral administration of the total flavonoids from Polygonum aviculare. Samples were prepared by solid-phase extraction then separated on a C₁₈ reversed-phase column by use of a mobile-phase gradient prepared from methanol and aqueous formic acid solution. The flow rate was 1 mL min^?1. Detection was performed at 254 nm. The calibration range was 11–1,100 μg mL^?1 for both 2 and 3 in plasma; in urine the calibration ranges for 1, 2, and 3 were 32–1,600, 11–1,100, and 22–1,100 μg mL^?1, respectively. Intra-day and inter-day RSD were less than 4.33 and 3.62% for 2 and 3, respectively, in plasma, and no more than 4.03 and 2.22% for all the analytes in urine. The analytical sensitivity and selectivity of the assay enabled successful application to pharmacokinetic studies of flavonols 1–3 in rats.     

Silver(I) Compounds with Perfluorinated Aromatic Thiols C6F5C6F4SH,C10F7SH,and C6F5SH as Precursors for Silver Nanoparticles

Silver(I) compounds with perfluorinated aromatic thiols (4-nonafluorodiphenylthiol C₆F₅C₆F₄SH (HL¹), 2-heptafluoronaphthalenethiol C₁₀F₇SH (HL²), and pentafluorothiophenol C₆F₅SH (HL³), namely AgL¹ (I), AgL² (II), AgL³ (III), were prepared. The thermal properties of compounds I–III and the composition of thermolysis products were studied. By powder X-ray diffraction and electron microscopy, it was shown that thermolysis of compounds I–III under argon and thermolysis of compound III in air yield Ag nanoparticles.     

Divalent Pb(0) compounds

Density functional theory (DFT) calculations have been carried out on four novel dicoordinated lead compounds PbL₂ where L is an N-heterocyclic ylidene or a five-membered cyclic ylidene (1Pb, 2Pb, 4Pb, 5Pb) and for a plumbylene-coordinated carbone CL₂ (3Pb). The theoretically predicted equilibrium geometries and the first and second proton affinities of 1Pb?C5Pb are reported. Geometry optimizations have also been carried out for the complexes with one and two BH₃ ligands 1Pb(BH ₃ )?C5Pb(BH ₃ ) and 1Pb(BH ₃ ) ₂ ?C5Pb(BH ₃ ) ₂ , and for the transition metal complexes 1PbW(CO) ₅ ?C5PbW(CO) ₅ and 1PbNi(CO) ₃ ?C5PbNi(CO) ₃ . The results suggest that the molecules 1Pb, 2Pb and 4Pb possess properties which identify them as divalent Pb(0) compounds (plumbylones). This comes to the fore by the theoretically predicted second PAs which are very large for a lead compound and (for 1Pb and 4Pb) by the BDE of the second BH₃ ligand. Compound 3Pb should be considered as a plumbylene-coordinated divalent C(0) compound (carbone) which has a very high second PA of 195.1?kcal/mol. The geometry optimization of 5Pb gives an equilibrium structure which identifies the molecules as divalent Pb(II) compound, i.e., as a plumbylene.     

Bis(tetraphenylantimony) succinate,malate, and tartrate: Syntheses and structures

The reactions of pentaphenylantimony with succinic, malic, and tartaric acids (mole ratio 2: 1) in toluene afford bis(tetraphenylantimony) succinate (I), malate (II), and tartrate (III) in yields of 98, 92, and 94%, respectively. According to the X_ray diffraction analysis results, molecules I and II are centrosymmetric. In compound II, the hydroxy group in the acid residue is disordered over two positions. Crystal III includes two types of crystallographically independent molecules (a and b). The antimony atoms in compounds I, II, IIIa, and IIIb have distorted trigonal bipyramidal coordination modes. The axial angles C_axSbO_ax are 166.80(8)° (I); 174.8(2)° (II); 176.4(4)°, 177.4(3)° (IIIa); and 173.3(4)°, 172.7(4)° (IIIb). The equatorial angles C_eqSbC_eq vary in the ranges 99.3(1)°–154.5(1)° (I); 115.2(2)°–123.3(2)° (II); 115.7(4)°–123.3(4)° 115.2(5)°–125.6(5)° (IIIa); and 107.9(4)°-129.1(4)°, 113.7(4)°-124.8(5)° (IIIb). The Sb-C and Sb-O bonds are 2.138(3)-2.176(3), 2.319(2) Å (I); 2.111(6)–2.163(5), 2.243(4) Å (II); 2.072(13)–2.169(11), 2.252(7), 2.284(7) Å (IIIa); and 2.047(11)–2.190(11), 2.224(7), 2.256(7) Å (IIIb). The intramolecular distances Sb…O=C are 2.528(3) (I); 3.267(7) (II); 3.381(7), 3.436(7) (IIIa); and 3.351(7), 3.162(7) Å (IIIb). For structures I, II, and III, the CIF files are CCDC 929151, 941542, and 941543, respectively.     

Comparison of novel pyridine-functionalized mesoporous silicas for Au(III) extraction from natural samples

A technique for solid-phase extraction utilizing pyridine-functionalized nanoporous silica (MCM-41, MCM-48 and SBA-15) was developed for the determination of gold in different samples using flame atomic absorption spectrometry. The effects of concentration and volume of eluent, pH of the solution, flow rate of extraction, sample volume and of potentially interfering ions on the efficiency of preconcentration and recovery was investigated. The limit of detection is lower than 45 pg mL^?1. Under optimal conditions, the accuracy and precision (RSD%) of the method were calculated to be >99.5% and <0.7% for the two MCMs (41 and 48) and >89.5%, and <1.5% for SBA-15, respectively. The SPE technique was used to determine the concentration of gold in natural and industrial wastewater with satisfactory results.