氮化硅陶瓷高温蠕变行为及Y_2O_3和CeO_2的影响

通过对材料高温下三点弯曲试样中心挠度与时间关系的分析,给出了通过挠度来表征材料高温蠕变性能的方法和表达式,并实际分析了3种不同添加剂氮化硅材料的高温蠕变性能。指出以Y2O3,CeO2为添加剂的氮化硅陶瓷经过热处理后比以MgO为添加剂的氮化硅陶瓷具有更好的抗高温蠕变性能。这主要是由于前者热处理后在晶界析出二次小晶粒,使晶界玻璃相大为减少,有效地抑制了高温下晶界的滑移。此外,Y,Ce与Si,N,O形成的玻璃相高温粘度高,也对材料抗高温变形有利。材料高温下往往是因为变形超过允许极限而失效。此时,通过挠度-时间关系可以很好地反映这一变化过程,并可初步判断材料使用的上限温度。     

Y2O3和CeO2对氮化硅烧结性能的影响

研究了Y2O3,CeO2的添加量在不同烧结温度下对Si3N4烧结性能的影响，分析了其助烧作用及晶界二次小晶粒形成的机制。结果表明，添加Y2O3,CeO2的Si3N4其烧结性能良好。Y2O3添加5％（此时Al2O3含量为4％）及CeO2为8％时对制品烧结促进作用最大。热处理后在Si3N4晶界获得结晶完美的二次小晶粒，使晶界玻璃相大为下降，为Si3N4高温力学性能的提高奠定结构基础。     

某些陶瓷的晶界

用高分辨电子显微镜观察、研究了某些陶瓷的晶界。结果表明:在小于5°小角度晶界的Si_3N_4中无玻璃相存在,玻璃相只存在于大角度晶界中间。大量非晶相存在降低材料高温强度。但是,通过选择较好的添加剂和使玻璃相晶化均可改善Si_3N_4陶瓷的高温力学性能。在β″—Al_2O_3和YBa_2Cu_3O_(7-x)陶瓷中,晶界的情况不同于Si_3N_4陶瓷,这里即使在大角度晶界上亦可以不存在玻璃相。     

Eu3+-Tb3+共掺杂SiO2-B2O3-Na2O-Y2O3-P2O5玻璃陶瓷的制备与发光性能

采用高温熔融法制备Eu3+?Tb3+共掺杂SiO2?B2O3?Na2O?Y2O3?P2O5前驱体玻璃。对前驱体玻璃粉末进行差示扫描量热(DSC)分析,确定玻璃陶瓷样品的热处理温度。前驱体玻璃热处理后,采用X射线衍射(XRD)和扫描电镜(SEM)分析可知前驱体玻璃中有Na3.6Y1.8(PO4)3晶粒析出。利用荧光光谱对玻璃陶瓷样品的发光性能进行表征,同时分析了Tb3+离子的荧光衰减曲线,确定Eu3+、Tb3+离子的发光机理以及能量传递过程。通过对Eu3+?Tb3+共掺杂玻璃陶瓷样品的发射光谱采集并用色坐标软件和色温计算程序,获得玻璃陶瓷样品的色坐标和相关色温。     

Al2O3-30％TiCN-0.2％Y2O3复相陶瓷的氧化性研究

对热压法制备的Al2O3-30％TiCN-0.2％Y2O3复合陶瓷抗高温氧化性能的研究。结果表明：该材料在空气中静态氧化时的氧化增重符合抛物线规律，氧化产物主要随氧化时间增加，氧化温度的提高而增加，该材料具有较好的抗氧化性能。Al2O3-30％TiCN-0.2％Y2O3复相陶瓷的氧化产物为TiO2。由于氧化产物TiO2存在以及氧化反应的体积膨胀效应，使氧化膜中产生残余应力并导致氧化膜的破坏，适当的氧化处理可使Al2O3-30％TiCN-0.2％Y2O3陶瓷材料的抗弯强度得到一定程度的提高，强度提高可达4．5％。     

掺杂Sm_2O_3的Y_2O_3-2TiO_2系微波介质陶瓷的性能研究

以具有中介电常数的新型Y2O3-2TiO2系微波介质陶瓷为基体,选用Sm2O3作为掺杂改性剂,通过传统固相法制备成陶瓷。重点研究了不同Sm2O3掺杂量对基体Y2O3-2TiO2微波介质陶瓷物相组成和介电性能的影响。采用X射线衍射和扫描电子显微镜分别对其物相组成和显微结构进行了分析,用阻抗分析仪和网络分析仪测试其介电性能。结果表明:掺杂Sm2O3未改变材料的主晶相,仍为A2B2O7烧绿石结构,Sm3+取代Y3+占据A位;掺杂有效降低了陶瓷的烧结温度,掺杂量为5%(质量分数)时,烧结温度为1330℃,材料的综合性能最佳,εr=23,tanδ=0.0046,Q×f=6713 GHz。     

RE2O3-Al2O3-SiO2玻璃连接氮化硅合成复相陶瓷的研究

采用Ｙ２Ｏ３－Ａｌ２Ｏ３－ＳｉＯ２－Ｘ稀土玻璃进行氮化硅复相陶瓷的连接。用四点弯曲方法测定不同连接工艺下的连接强度。并对连接界面进行ＳＥＭ、ＥＰＭＡ和ＸＲＤ分析。液相钎料玻璃在界面上与氮化硅反应，形成氮化硅／Ｓｉ２Ｎ２Ｏ／Ｙ（Ｌａ）－Ｓｉａｌｏｎ玻璃／Ｙ（Ｌａ）－Ｓｉａｌｏ玻璃的梯度层界面。接头强度随着保温时间、妆温度的增加，先增后。 在ＹＡＳ钎料中添加氧化镧，可以提高接头的高温强度。ＬａＹＯ３的     

Y2O3薄膜处理对3Cr25Ni7N合金的抗高温氧化性能的影响

采用电沉积-热解法在3Cr25Ni7N合金表面制备了Y2O3薄膜,并研究了薄膜处理对合金在1000℃空气中的抗高温氧化性能的影响。氧化动力学曲线、SEM及XRD分析结果表明,Y2O3薄膜处理使合金表面氧化膜以尖晶石结构为主,氧化膜致密,有效地抑制了Cr2O3的挥发反应,且氧化膜与基体的附着性好,因此合金在高温下的抗氧化性能得到提高,这与氧化钇薄膜在较低温度下抗高温氧化性能提高的机制是不同的。在不同温度下,Y2O3薄膜处理均可以有效提高合金的抗高温氧化性能。     

第四组元对Y_2O_3-Al_2O_3-SiO_2钎料连接氮化硅陶瓷的影响

在Y2 O3 Al2 O3 SiO2 (YAS)钎料中添加TiO2 (YT)和Si3N4(YN) ,并进行氮化硅陶瓷的连接。用四点弯曲方法测定不同连接工艺下的连接强度 ,并对连接界面进行SEM ,EPMA和XRD分析。接头强度随着保温时间、连接温度的增加 ,而逐渐增加。在达到峰值后 ,连接强度逐渐降低。在YAS中添加TiO2 ,可以形成Si3N4/Y Sialon玻璃 TiN/TiN/Y Sialo玻璃的梯度层界面 ;而在YAS钎料中添加Si3N4,可以降低接头界面的热应力 ,改善接头强度。微观分析表明 :接头强度的变化主要与界面反应有关。     

SrAl_2O_4∶Eu的荧光效应及其陶瓷漫反射特性

采用SrAl2 O4∶Eu荧光材料为主相制备具有紫外线转换功能的陶瓷泵浦腔材料。研究了SrAl2 O4∶Eu粉体制备与荧光性能的关系 ,考察其与低折射率玻璃复合制成陶瓷的漫反射性能及反射谱特性。结果显示SrAl2 O4∶Eu基陶瓷作为泵浦腔用材料在技术上是可行的。     

2-Formyl-3-Methoxymethylindole, 3-Ethoxymethyl-2-Formylindole and 2-Formyl-3-Methylindole

Base-catalysed hydrolysis of 2-formyl-3-methyl-1-phenyl-sulphonylindole results in the formation of 3-alkoxy-methyl-2-formylindoles. Cleavage of the 1-phenyl-sulphonyl group with sodium amalgam produces 2-hydroxymethyl-3-methylindole.     

Methanesulfonates of high-valent metals: syntheses and structural features of MoO2(CH3SO3)2, UO2(CH3SO3)2, ReO3(CH3SO3), VO(CH3SO3)2, and V2O3(CH3SO3)4 and their thermal decomposition under N2 and O2 atmosphere

Oxide methanesulfonates of Mo, U, Re, and V have been prepared by reaction of MoO(3), UO(2)(CH(3)COO)(2)·2H(2)O, Re(2)O(7)(H(2)O)(2), and V(2)O(5) with CH(3)SO(3)H or mixtures thereof with its anhydride. These compounds are the first examples of solvent-free oxide methanesulfonates of these elements. MoO(2)(CH(3)SO(3))(2) (Pbca, a=1487.05(4), b=752.55(2), c=1549.61(5) pm, V=1.73414(9) nm(3), Z=8) contains [MoO(2)] moieties connected by [CH(3)SO(3)] ions to form layers parallel to (100). UO(2)(CH(3)SO(3))(2) (P2(1)/c, a=1320.4(1), b=1014.41(6), c=1533.7(1) pm, β=112.80(1)°, V=1.8937(3) nm(3), Z=8) consists of linear UO(2)(2+) ions coordinated by five [CH(3)SO(3)] ions, forming a layer structure. VO(CH(3)SO(3))(2) (P2(1)/c, a=1136.5(1), b=869.87(7), c=915.5(1) pm, β=113.66(1)°, V=0.8290(2) nm(3), Z=4) contains [VO] units connected by methanesulfonate anions to form corrugated layers parallel to (100). In ReO(3)(CH(3)SO(3)) (P1, a=574.0(1), b=1279.6(3), c=1641.9(3) pm, α=102.08(2), β=96.11(2), γ=99.04(2)°, V=1.1523(4) nm(3), Z=8) a chain structure exhibiting infinite O-[ReO(2)]-O-[ReO(2)]-O chains is formed. Each [ReO(2)]-O-[ReO(2)] unit is coordinated by two bidentate [CH(3)SO(3)] ions. V(2)O(3)(CH(3)SO(3))(4) (I2/a, a=1645.2(3), b=583.1(1), c=1670.2(3) pm, β=102.58(3), V=1.5637(5) pm(3), Z=4) adopts a chain structure, too, but contains discrete [VO]-O-[VO] moieties, each coordinated by two bidentate [CH(3)SO(3)] ligands. Additional methanesulfonate ions connect the [V(2)O(3)] groups along [001]. Thermal decomposition of the compounds was monitored under N(2) and O(2) atmosphere by thermogravimetric/differential thermal analysis and XRD measurements. Under N(2) the decomposition proceeds with reduction of the metal leading to the oxides MoO(2), U(3)O(7), V(4)O(7), and VO(2); for MoO(2)(CH(3)SO(3))(2), a small amount of MoS(2) is formed. If the thermal decomposition is carried out in a atmosphere of O(2) the oxides MoO(3) and V(2)O(5) are formed.     

Synthesis and structure of 2-ethoxy- and 2-aminomethylidene-3-fluoroalkyl-3-oxopropionates

Condensation of ethyl 3-polyfluoroalkyl-3-oxopropionates with excess triethyl orthoformate gave ethyl 3-polyfluoroalkyl-2-ethoxymethylidene-3-oxopropionates which reacted with primary aliphatic, aromatic, and heterocyclic amines to form ethyl 2-alkyl(aryl, hetaryl)aminomethylidene-3-polyfluoroalkyl-3-oxopropionates. According to the X-ray diffraction and IR data, the latter exist in the crystalline state as the corresponding E isomers, while in solution (NMR data), as mixtures of Z and E isomers. Condensation of ethyl 2-ethoxymethylidene-3-oxopropionates with secondary heterocyclic amines (morpholine and pyrrolidine) led to the formation of 2-morpholino(pyrrolidin-1-yl)methylidene-3-fluoroalkyl-3-oxopropionates which were shown to exist as Z isomers both in the crystalline state and in solution.     

Kinetics of gas‐phase reactions of CH3OCH2CF3, CH3OCH3, CH3OCH2CH3, CH3CH2OCH2CH3, and CHF2CF2OCH2CF3 with NO3 radicals at 298 K

Rate constants for the gas‐phase reactions of CH₃OCH₂CF₃ (k₁), CH₃OCH₃ (k₂), CH₃OCH₂CH₃ (k₃), and CH₃CH₂OCH₂CH₃ (k₄) with NO₃ radicals were determined by means of a relative rate method at 298 K. NO₃ radicals were prepared by thermal decomposition of N₂O₅ in a 700–750 Torr N₂O₅/NO₂/NO₃/air gas mixture in a 1‐m³ temperature‐controlled chamber. The measured rate constants at 298 K were k₁ = (5.3 ± 0.9) × 10^?18, k₂ = (1.07 ± 0.10) × 10^?16, k₃ = (7.81 ± 0.36) × 10^?16, and k₄ = (2.80 ± 0.10) × 10^?15 cm³ molecule^?1 s^?1. Potential energy surfaces for the NO₃ radical reactions were computationally explored, and the rate constants of k₁–k₅ were calculated according to the transition state theory. The calculated values of rate constants k₁–k₄ were in reasonable agreement with the experimentally determined values. The calculated value of k₅ was compared with the estimate (k₅ < 5.3 × 10^?21 cm³ molecule^?1 s^?1) derived from the correlation between the rate constants for reactions with NO₃ radicals (k₁–k₄) and the corresponding rate constants for reactions with OH radicals. We estimated the tropospheric lifetimes of CH₃OCH₂CF₃ and CHF₂CF₂OCH₂CF₃ to be 240 and >2.4 × 10⁵ years, respectively, with respect to reaction with NO₃ radicals. The tropospheric lifetimes of these compounds are much shorter with respect to the OH reaction. © 2009 Wiley Periodicals, Inc. Int J Chem Kinet 41: 490–497, 2009     

Eu3+掺杂Y2O3-Al2O3-SiO2玻璃的制备与荧光性能研究

采用高温熔融法制备了Eu³⁺掺杂Y₂O₃-Al₂O₃-SiO₂荧光玻璃,探讨了成分对该体系玻璃形成能力的影响,并对不同Eu³⁺掺杂浓度下的荧光性能进行了研究.结果表明,熔融温度为1500℃条件下,SiO₂含量对该体系的玻璃形成能力影响明显,Y/Al摩尔比为3/5时,SiO₂含量在52%-68%(摩尔分数)范围内时可以获得玻璃.掺杂Eu³⁺的Y₂O₃-Al₂O₃-SiO₂玻璃具有荧光性能,在395nm波长激发下,在588 nm和614 nm处出现明显的发射峰.随着Eu³⁺掺杂浓度的增加,该荧光玻璃的发射波长不变,但发射强度有所变化;当Eu³⁺掺杂浓度为1.5%(摩尔分数)时,特征发射峰强度最大.     

Michael condensation of 3-arylidene-3H-pyrrol-2-ones and 3-arylidene-3H-furan-2-ones with cyclohexanone

The Michael condensation in the series of 5-aryl-3-arylidene-3H-pyrrol-2-ones and 5-aryl-3-arylidene-3H-furan-2-ones, containing an activated C=C bond, with cyclohexanone was investigated. It was shown that the condensation products were 1,5-dicarbonyl compounds containing a heterocyclic fragment. The enolization of one of the oxo groups, leading to the formation of hydroxypyrrole or hydroxyfuran structures, was demonstrated by the spectral data. __________ Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 6, pp. 823–827, June, 2007.     

Preparation and Characterization of FeCo-Al2O3 and Al2O3 Aerogels

Nanocrystalline γ-Al₂O₃ and FeCo-Al₂O₃ nanocomposites containing FeCo alloy nanoparticles well dispersed in the nanocrystalline γ-Al₂O₃ matrix were successfully obtained by the sol-gel method using aluminum tri-sec-butoxide and iron and cobalt nitrates as precursors. The gels were submitted to high temperature supercritical drying which allowed to obtain aerogels with high surface areas and pore volumes.