Matrix solid-phase dispersion extraction of organophosphorus pesticides from propolis extracts and recovery evaluation by GC/MS

Five organophosphorus pesticides (dichlorvos, diazinon, malathion, methyl parathion and coumaphos) were extracted from propolis by matrix solid-phase dispersion (MSPD) extraction using octadecylsilica (C18, 1.0 g) as dispersant material. The kind of solvent elution (acetonitrile or ethyl acetate), volume (8 mL and 15 mL), and adsorbent used to clean-up the extracts (graphitized carbon, florisil™ and silica) were optimized using fortified propolis samples (5.0 μg g⁻¹). Recovery was determined by gas chromatography with mass spectrometric detection in selected ion monitoring mode (GC/MS-SIM) and statistical analysis was done to determine better extraction conditions. Relatively high recovery and lower relative standard deviation values (3.1–14.6%) were obtained when analytes were eluted with ethyl acetate from the MSPD column. Diazinon, malathion, methyl parathion, and coumaphos show recoveries of 72.7%, 84.6%, 62.6%, and 78.3%, respectively. In contrast, the recovery for dichlorvos was 53.8%. Additional adsorbents tested for clean-up and increase in solvent elution did not affect recoveries positively and caused a high background in chromatograms. Thus, final conditions were 1 mL of sample, 1 g C18 and 8 mL of ethyl acetate.     

Matrix solid-phase dispersion extraction of carbadox and olaquindox in feed followed by hydrophilic interaction ultra-high-pressure liquid chromatographic analysis

A new method involving matrix solid-phase dispersion (MSPD) extraction and hydrophilic interaction ultra-high-pressure liquid chromatography (HILIC-UHPLC) with photodiode array detection was developed for the determination of carbadox and olaquindox in feed. Separation of carbadox and olaquindox was achieved within 1 min on the 1.7 microm Acquity UPLC BEH HILIC column by using isocratic elution with a mobile phase consisting of 10 mmol L(-1) ammonium acetate in acetonitrile-water (95:5, v/v) at a flow rate of 0.5 mL min(-1). Optimization of MSPD extraction parameters, such as type of solid sorbent and elution solvent were carried out. Optimal conditions selected for MSPD extraction were: 0.25 g of feed sample, 0.5 g of octadecylsilica as solid sorbent and 10 mL of acetonitrile-methanol (8:2, v/v) as eluting solvent. Both analytes provided average recoveries from spiked feed samples ranging from 89.1 to 98.4% with relative standard deviations less than 10%. Obtained performance characteristics are comparable to those achieved by liquid-liquid extraction-HPLC with the advantages of being simpler and significantly faster.     

Optimization of the matrix solid-phase dispersion sample preparation procedure for analysis of polycyclic aromatic hydrocarbons in soils: comparison with microwave-assisted extraction

A fast and simple preparation procedure based on the matrix solid-phase dispersion (MSPD) technique is proposed for the first time for the isolation of 16 polycyclic aromatic hydrocarbons (PAHs) from soil samples. Naphthalene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benz[a]anthracene, chrysene, benzo[e]pyrene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenzo[a,h]anthracene, benzo[g,h,i]perylene, and indeno[1,2,3-c,d]pyrene were considered in the study. Extraction and clean-up of samples were carried out in a single step. The main parameters that affect extraction yield, such as dispersant, type and amount of additives, clean-up co-sorbent and extractive solvent were evaluated and optimized. The addition of an alkali solution in MSPD was required to provide quantitative recoveries. Analytical determinations were carried out by high performance liquid chromatography (HPLC) with fluorescence detection. Quantification limits (between 0.01 and 0.6 ng g(-1) dry mass) were well below the regulatory limits for all the compounds considered. The extraction yields for the different compounds obtained by MSPD were compared with the yields obtained by microwave-assisted extraction (MAE). To test the accuracy of the MSPD technique, the optimized methodology was applied to the analysis of standard reference material BCR-524 (contaminated industrial soil), with excellent results.     

Application of matrix solid-phase dispersion to the determination of a new generation of fungicides in fruits and vegetables

A method based on matrix solid-phase dispersion (MSPD) and gas chromatography to determine eight fungicides in fruits and vegetables is described. Fungicide residues were identified and quantified using nitrogen-phosphorus detection and electron-capture detection connected in parallel and confirmed by mass spectrometric detection. The method required 0.5 g of sample, C18 bonded silica as dispersant sorbent, silica as clean-up sorbent and ethyl acetate as eluting solvent. Recoveries from spiked orange, apple, tomato, artichoke, carrot and courgette samples ranged from 62 to 102% and relative standard deviations were less than 15% in the concentration range 0.05-10 mg kg(-1). Detection and quantitation limits ranged 3-30 microg kg(-1) and 10-100 microg kg(-1), respectively, with linear calibration curves up to 10 mg kg(-1). The analytical characteristics of MSPD compared very favourably with the results of a classical multiresidue method, which uses ethyl acetate and anhydrous sodium sulphate for the extraction.     

水果蔬菜中多种杀菌剂的基质固相分散液相色谱测定方法研究

采用基质固相分散(MSPD)代替液液分配和固相萃取,从蔬菜水果中提取、净化10种常用杀菌剂农药残留,用C18硅胶交联剂作为固相吸附剂,乙酸乙酯作为洗脱液,用HPLC/PDA和LC-MS进行分析检测。10种杀菌剂在0.5~5 mg/kg含量的添加回收率在65%~110%之间,相对标准偏差小于10%,使用HPLC、PDA和LC-MS的检出限分别在0.02~0.2 mg/kg和0.002~0.01 mg/kg之间。该方法节省溶剂,提取和净化一步完成,适用于新鲜水果和蔬菜中10种杀菌剂的残留分析。     

Matrix Solid-Phase Dispersion Extraction and UPLC Determination of Sudan Dyes in Chili Powder

A new method involving matrix solid-phase dispersion (MSPD) extraction and UPLC in conjunction with photodiode array detection was developed for the rapid and simple determination of Sudan dyes in chili powder. Separation of Sudan I, Sudan II, Sudan III, and Sudan IV was achieved within 2 min on the 1.7 μm Acquity UPLC BEH C18 column by using gradient elution with a mobile phase consisting of acetonitrile–water at a flow rate of 0.5 mL min⁻¹. Optimization of MSPD extraction parameters, such as type of solid sorbent and elution solvent were carried out. Optimal conditions selected for MSPD extraction were 0.25 g of sample, 0.5 g of silica gel as solid sorbent, and 7 mL of acetonitrile–methanol (9:1, v/v) as eluting solvent. Limits of detection ranged between 0.25 and 0.30 mg kg⁻¹ depending on the dye involved. All analytes provided average recoveries from spiked (at 1, 1.5, and 2 mg kg⁻¹) chili powder samples ranging from 81 to 106%. The method was applied to the analysis of chili powder samples obtained from different countries.

     

Matrix Solid-Phase Dispersion Extraction and UPLC Determination of Sudan Dyes in Chili Powder

A new method involving matrix solid-phase dispersion (MSPD) extraction and UPLC in conjunction with photodiode array detection was developed for the rapid and simple determination of Sudan dyes in chili powder. Separation of Sudan I, Sudan II, Sudan III, and Sudan IV was achieved within 2 min on the 1.7 μm Acquity UPLC BEH C18 column by using gradient elution with a mobile phase consisting of acetonitrile–water at a flow rate of 0.5 mL min^?1. Optimization of MSPD extraction parameters, such as type of solid sorbent and elution solvent were carried out. Optimal conditions selected for MSPD extraction were 0.25 g of sample, 0.5 g of silica gel as solid sorbent, and 7 mL of acetonitrile–methanol (9:1, v/v) as eluting solvent. Limits of detection ranged between 0.25 and 0.30 mg kg^?1 depending on the dye involved. All analytes provided average recoveries from spiked (at 1, 1.5, and 2 mg kg^?1) chili powder samples ranging from 81 to 106%. The method was applied to the analysis of chili powder samples obtained from different countries.     

Development of a matrix solid-phase dispersion method for the determination of polycyclic aromatic hydrocarbons in sewage sludge samples

A new, single-step extraction and purification method based on matrix solid-phase dispersion (MSPD) was developed to determine 17 polycyclic aromatic hydrocarbons (PAHs) in sewage sludge samples. The MSPD method consists of sample homogenisation, exhaustive extraction and clean-up by a single process. The different operational parameters of the method, such as the type of dispersant, type and amount of additives, clean-up co-sorbent and extractive solvent were evaluated. Reversed-phase (C18) and polymeric (Oasis HLB and Oasis MAX) materials, as well as normal phase sorbents (Florisil, silica, neutral alumina) and an inert support (sand) were tested to assess the sorbents effect on the yield and selectivity of the MSPD process. Analysis of extracts was performed by high performance liquid chromatography (HPLC) coupled with fluorescence detection.Quantification limits obtained for all of these considered compounds (between 0.0001 and 0.005 μg g⁻¹ dry mass) were well below of the limits recommended in the EU. The extraction yields for the different compounds obtained by MSPD ranged from 76.3% to 103.6%. On the other hand, the extraction efficiency of the optimised method is compared with that achieved by microwave-assisted extraction and the method was applied to the analysis of real sewage sludge samples. A certified reference material (sewage sludge (BCR 088)) and a reference material (sewage sludge (RTC-CNS312-04)) were used to validate the proposed method.     

Determination of Procymidone, Pentachloroaniline and Methyl-pentachloro-phenylsulfide Residues in Wine by MSPD-GC-ECD

A rapid method based on matrix solid-phase dispersion (MSPD) was developed for the determination of procymidone, pentachloroaniline and methyl-pentachloro-phenylsulfide in wine. After the optimisation of different parameters such as the type of adsorbent, the extraction solvent, and the extraction assistance by sonication. The analysis of samples was accomplished using gas chromatography with electron-capture detector (GC-ECD). Spiked blank samples were used as standards to counteract the matrix effect observed in the chromatographic determination. The recovery of the method was in the range 82.4–93.7% and a good linear relationship (R ² ≥ 0.9992) with relative standard deviations lower than 8%. The limits of detection (LOD) ranged from 0.1 to 0.4 μg L^?1. The proposed method was applied to the analysis of these compounds in commercial wine samples.     

Comparison of extraction techniques for quantitative analysis of pendimethalin from soil and rice grain

The paper exploits the development, optimization, and comparison of fast, efficient, quantitative analytical extraction techniques such as ultrasonic-assisted extraction (UAE) and matrix solid-phase dispersion (MSPD) for proficient extraction of pendimethalin from soil and rice samples. Residues of pendimethalin were quantified using high-performance liquid chromatography. Impact of several experimental parameters of UAE and MSPD techniques on extraction of pendimethalin from soil and rice samples was also evaluated. Under the optimized conditions, the mean percent recoveries obtained from both methods were in the range of 80.3–101.3 and 81.7–103.1, respectively, with relative standard deviation <10. Linearity was in the range of 0.003–5.0?µg?mL^?1 with limit of detection and limit of quantification as 0.001 and 0.003?µg?g^?1, respectively. MSPD method was found superior in terms of low solvent consumption, small sample size, and reduced matrix coextracts due to simultaneous extraction and cleanup steps. Both extraction methodologies were successfully applied in monitoring routine soil and rice samples, in which pendimethalin residues (0.003–0.007?µg?g^?1) were detected in few rice samples while residues in soil samples were below the quantification limit.     

Miniaturized matrix solid phase dispersion procedure and solid phase microextraction for the analysis of organochlorinated pesticides and polybrominated diphenylethers in biota samples by gas chromatography electron capture detection

This work has developed a miniaturized method based on matrix solid phase dispersion (MSPD) using C18 as dispersant and acetonitrile–water as eluting solvent for the analysis of legislated organochlorinated pesticides (OCPs) and polybrominated diphenylethers (PBDEs) in biota samples by GC with electron capture (GC-ECD). The method has compared Florisil^®-acidic Silica and C18 as dispersant for samples as well as different solvents. Recovery studies showed that the combination of C18–Florisil^® was better when using low amount of samples (0.1 g) and with low volumes of acetonitrile–water (2.6 mL). The use of SPME for extracting the analytes from the solvent mixture before the injection resulted in detection limits between 0.3 and 7.0 μg kg⁻¹ (expressed as wet mass). The miniaturized procedure was easier, faster, less time consuming than the conventional procedure and reduces the amounts of sample, dispersant and solvent volume by approximately 10 times. The proposed procedure was applied to analyse several biota samples from different parts of the Comunidad Valenciana.     

Optimization of a matrix solid-phase dispersion method with sequential clean-up for the determination of alkylphenol ethoxylates in biological tissues

A modified Matrix Solid-Phase Dispersion (MSPD) method with sequential clean-up has been developed to isolate and purify alkylphenol ethoxylates (APEs) and alkylphenols in biological tissues. Elution profile, sequential clean-up adsorbent and experimental set up were optimized. Octadecylsilica was used as the solid-phase for matrix dispersion. Methanol was found to be the optimal eluting solvent for APEs. Aluminium oxide was quite efficient for removing the coeluting interferences. Quantitative analysis was done by reversed-phase HPLC with fluorescence detection. The optimized procedure was applied to analyze both fish and mussel samples. Average recoveries for all spiked tissue samples were greater than 90%. Typical limits of detection amount to tens of ppbs on a wet weight basis.     

Response surface optimization for determination of pesticide multiresidues by matrix solid-phase dispersion and gas chromatography

An optimized multiresidue analysis method based on matrix solid-phase dispersion (MSPD) and gas chromatography (GC) is proposed for the determination of organochlorines and pyrethroids in the tea samples. Response surface methodology (RSM) was used to optimize the extraction conditions of MSPD, such as the sorbent type, eluent composition, dichloromethane concentration and eluting volume. Desirability function approach was employed to optimize the pesticide recoveries and matrix cleanup. Compromising the recoveries and cleanup degree, MSPD was carried out with Florisil as the sorbent and n-hexane-dichloromethane (1:1, v/v) as the eluent. The pesticide recoveries in tea samples were better than 80% spiked in the concentration range of 0.01-0.05mg/kg and the relative standard deviations were lower than 7%. The quantification limits of the pesticides were in the range of 0.002-0.06mg/kg, which were lower than the maximum residue limits of the pesticides in tea samples established by the European Union.     

Selective enrichment of the degradation products of organophosphorus nerve agents by zirconia based solid-phase extraction

Selective extraction and enrichment of nerve agent degradation products has been achieved using zirconia based commercial solid-phase extraction cartridges. Target analytes were O-alkyl alkylphosphonic acids and alkylphosphonic acids, the environmental markers of nerve agents such as sarin, soman and VX. Critical extraction parameters such as modifier concentration, nature and volume of washing and eluting solvents were investigated. Amongst other anionic compounds, selectivity in extraction was observed for organophosphorus compounds. Recoveries of analytes were determined by GC-MS which ranged from 80% to 115%. Comparison of zirconia based solid-phase extraction method with anion-exchange solid-phase extraction revealed its selectivity towards phosphonic acids. The limits of detection (LOD) and limit of quantification (LOQ) with selected analytes were achieved down to 4.3 and 8.5 ng mL(-1), respectively, in selected ion monitoring mode.     

Simultaneous determination of eight pesticide residues in coconut using MSPD and GC/MS

A simple and effective extraction method based on matrix solid-phase dispersion (MSPD) was developed to determine dimethoate, malathion, lufenuron, carbofuran, 3-hydroxycarbofuran, thiabendazole, difenoconazole and trichlorfon in coconut pulp using gas chromatography-mass spectrometry with selected ion monitoring (GC/MS, SIM). Different parameters of the method were evaluated, such as type of solid-phase (C(18), alumina, silica-gel and Florisil), the amount of solid-phase and eluent (dichloromethane, acetone, ethyl acetate, acetonitrile, n-hexane and n-hexane:ethyl acetate (1:1, v/v)). The best results were obtained using 0.5 g of coconut pulp, 1.0 g of C(18) as dispersant sorbent, 1.0 g of Florisil as clean-up sorbent and acetonitrile saturated with n-hexane as eluting solvent. The method was validated using coconut pulp samples fortified with pesticides at different concentration levels (0.25-1.0 mg kg(-1)). Average recoveries (four replicates) ranged from 70.1% to 98.7%, with relative standard deviations between 2.7% and 14.7%, except for lufenuron and difenoconazole, for which recoveries were 47.2% and 48.2%, respectively. Detection and quantification limits for coconut pulp ranged from 0.02 to 0.17 mg kg(-1) and from 0.15 to 0.25 mg kg(-1), respectively.     

Fast and selective extraction of chloramphenicol from soil by matrix solid‐phase dispersion using molecularly imprinted polymer as dispersant

The molecularly imprinted polymer (MIP) was synthesized and used as dispersant of matrix solid‐phase dispersion (MSPD) for the extraction of chloramphenicol (CAP) in soil samples. The satisfactory recovery of CAP was obtained by the optimized extraction conditions: 1:2 as the ratio of sample to MIPs; 5 min as the dispersion time; 30% aqueous methanol as washing solvent and methanol as elution solvent. The CAP extracted from soil was determined by LC‐MS/MS. The slight ion suppression phenomenon was observed for the CAP when the sample was cleaned up by MSPD with MIP as dispersant, when compared with C18 as MSPD dispersant, which caused significant ion suppression. LOD of CAP is 4.1 ng/g. RSDs of intra‐ and inter‐day tests ranging from 3.1 to 6.2% and from 3.9 to 8.3% are obtained. At all three fortified levels (20, 100 and 500 ng/g), recoveries of CAP are in the range of 86.9–92.6%. The effect of ageing time of spiked soil sample on the CAP recovery was examined. The CAP recovery decreased from 91.0 to 36.9% when the ageing time changed from 1 day to 4 wk.     

Response surface optimization for determination of pesticide residues in grapes using MSPD and GC-MS: assessment of global uncertainty

In this work, a simple and low-cost method based on matrix solid-phase dispersion (MSPD) and gas chromatography to determine eight multi-class pesticides such as vinclozolin, dichlofluanid, penconazol, captan, quinoxyfen, fluquinconazol, boscalid, and pyraclostrobin in grapes is described. Fungicide residues were identified and quantified using gas chromatography–mass spectrometry in selected ion monitoring mode (GC-MS, SIM). The experimental variables that affect the MSPD method, such as the amount of solid phase, solvent nature and elution volume were optimized using an experimental design. The best results were obtained using 0.5 g of grapes, 1.0 g of silica as clean-up sorbent, 1.50 g of C₁₈ as bonded phase and 10 mL of dichloromethane/ethyl acetate (1:1, v/v) as eluting solvent. Significant matrix effects observed for most of the pesticides tested were eliminated using matrix-matched standards. The pesticide recoveries in grapes samples were better than 80% except for captan. Intra-laboratory precision in terms of Horwitz ratio of the pesticides evaluated was below 0.5, suggesting ruggedness of the method. The quantification limits of the pesticides were in the range of 3.4–8.7 μg kg⁻¹, which were lower than the maximum residue limits (MRLs) of the pesticides in grapes samples established by the European legislation. Decision limits (CCα) and detection capability (CCβ) have been calculated. The expanded uncertainties at two levels of concentration were <20% for all analytes.     

Carbon molecular sieve based micro‐matrix‐solid‐phase dispersion for the extraction of polyphenols in pomegranate peel by UHPLC‐Q‐TOF/MS

A rapid, simple, and efficient sample extraction method based on micro‐matrix‐solid‐phase dispersion (micro‐MSPD) was applied to the extraction of polyphenols from pomegranate peel. Five target analytes were determined by ultra‐HPLC coupled with Q‐TOF/MS. Carbon molecular sieve (CMS) was firstly used as dispersant to improve extraction efficiency in micro‐MSPD. The major micro‐MSPD parameters, such as type of dispersant, amount of dispersant, grinding time, and the type and the volume of elution solvents, were studied and optimized. Under optimized conditions, 26 mg of pomegranate peel was dispersed with 32.5 mg of CMS, the grinding time was selected as 90 s, the dispersed sample was eluted with 100 μL of methanol. Results showed that the proposed method was of good linearity for concentrations of analytes against their peak areas (coefficient of determination r² > 0.990), the LOD was as low as 3.2 ng/mL, and the spiking recoveries were between 88.1 and 106%. Satisfactory results were obtained for the extraction of gallic acid, punicalagin A, punicalagin B, catechin, and ellagic acid from pomegranate peel sample, which demonstrated nice reliability and high sensitivity of this approach.     

Optimization of matrix solid-phase dispersion conditions for UV filters determination in biota samples

A low solvent consumption method for the determination of eight ultraviolet (UV) filters, displaying low to medium polarities, in freeze-dried samples of marine bivalves and fish is proposed. Matrix solid-phase dispersion (MSPD) and gas chromatography with mass spectrometry (GC-MS) were used as sample preparation and determination techniques, respectively. This work describes the influence of several parameters (type and amount of dispersant and clean-up sorbents, as well as elution solvent) on the yield and the selectivity of the MSPD extraction. Under optimized conditions, samples (0.5?g) were ground with 2?g of Florisil in a mortar with a pestle and transferred into a polypropylene syringe, which contained 1?g of C18 as clean-up sorbent. Analytes were eluted with 5?mL of acetonitrile. This extract was concentrated to dryness, re-constituted with 1?mL of ethyl acetate and injected in the GC-MS system without any further clean-up. The global average recoveries, measured for three different biota samples, spiked at three different levels (between 50 and 1000?ng?g^?1), ranged from 80% to 101% with associated standard deviations below 10%. The inter-day precision of the method varied from 4% to 15% and the achieved LOQs (defined for a signal to noise ratio of 10) ranged from 4 to 28?ng?g^?1, referred to the freeze-dried matrix. Octocrylene (OCR) was found in some samples of fish and mussels at concentrations between 15 and 20?ng?g^?1, referred to dry mass.     

Multiwalled carbon nanotubes as efficient adsorbent for solid-phase extraction of chemical warfare agents and related chemicals from water

Optimization of extraction and enrichment parameters of chemical warfare agents and their related chemicals from water are presented using multiwalled carbon nanotubes (MWCNTs) as solid-phase extractant. Selected analytes were O,O'-dialkyl alkylphosphonates, nerve agent and mustards. Extraction parameters, including sample volume, nature and volume of washing and eluting solvent, were optimized. Recoveries of analytes were determined by GC-MS and ranged from 81 to 104%. A comparison with C(18), hydrophilic-lipophilic balance and active carbon sorbents demonstrated the superiority of MWCNTs for non-toxic analogues of nerve agents. Optimized conditions involve 40?mg MWCNTs as the sorbent, 5.0?mL water as the washing solvent, 3?mL ethyl acetate as the eluent and sample loading of 10?mL water spiked at 0.1?μg/mL. The limits of detection (LOD) were achieved down to 1 and 0.05?ng/mL in full scan and selected ion-monitoring modes, respectively.