巯丙基功能化介孔纳米二氧化硅的合成

用三种不同的方法将巯基丙基三甲氧基硅烷(MPTMS)引入二氧化硅网络中, 合成了粒径为50-200 nm的巯丙基功能化的介孔纳米二氧化硅, 并利用透射电子显微镜, 热重分析等手段对其形貌与性能进行了表征. 在巯丙基官能团的作用下介孔纳米二氧化硅的形貌发生了重大改变, 由非常规则的六角形变为纳米棒. 控制反应时间可以调节介孔纳米二氧化硅的粒径大小, 用三乙醇胺代替氢氧化钠可以合成直径在100 nm以下的功能化介孔二氧化硅粒子. 为了保护巯基官能团, 选用了酸醇提取法去除模板. 另外, 对介孔二氧化硅粒子的形成机制也进行了探讨.     

树枝状多孔二氧化硅纳米粒子的制备及其在先进载体中的应用

树枝状多孔二氧化硅纳米粒子具有中心辐射状孔道结构且孔道尺寸从粒子内部到粒子表面逐渐增加,是一种具有新颖结构的多孔材料。和传统的具有二维六方有序孔道结构的介孔二氧化硅粒子相比,这种粒子具有三维开放性的树枝状骨架结构,因而具有独特的结构优势,即高的孔渗透性和高的粒子内表面的可接触性,从而有利于物质（分子或纳米粒子）沿着中心辐射状的孔道进行输送,在树枝状粒子的内部负载或者与内部的活性位点发生反应。因此,这种粒子是一种很有前景的载体平台,可以用来构筑新型的吸附剂、纳米催化剂和基因药物的递送系统等。本综述首先介绍了一系列的合成方法和对树枝状骨架结构的调控策略,探讨了树枝状多孔结构对物理化学性能的影响,描述了其在催化、纳米生物医学、环境能源等领域的应用性能,并对树枝状多孔二氧化硅粒子的合成方向和应用前景进行了展望。     

有序介孔氧化硅薄膜制备及其组装化学

本文综述了近年来利用有机模板法合成有序介孔二氧化硅薄膜的研究进展，重点阐述了两相界面外延生长和蒸发诱导自组装两种制备方法及其合成机理。此外，讨论了有序介孔二氧化硅薄膜的组装化学，包括金属元素掺杂，纳米粒子在介孔薄膜中的组装，以及有机物/二氧化硅纳米复合薄膜的制备，并对介孔二氧化硅薄膜未来的发展趋势做了展望。     

中空纳米二氧化硅微球的制备及表征

本文介绍了一种制备中空纳米二氧化硅微球的新方法。利用模板首先合成介孔纳米二氧化硅微球,再用水热反应法,成功制备了非功能化和巯基、氨基功能化中空纳米二氧化硅微球。利用透射电子显微镜,热重分析等手段对其形貌进行了表征。另外,对中空介孔纳米二氧化硅微球的形成机制进行了探讨。     

固定化金属离子亲和发光二氧化硅纳米粒子的制备及其用于磷酸化蛋白免疫印迹标记

发展了一种能够识别磷酸化蛋白的固定化金属离子亲和发光二氧化硅纳米粒子用于免疫印迹(Western Blot)磷酸化蛋白的标记。首先通过反相微乳液Stöber方法合成了掺杂异硫氰酸荧光素硅烷化衍生物的发光二氧化硅(FITC@SiO₂)球形纳米粒子,粒子平均粒径为60 nm。然后通过共聚反应在FITC@SiO₂纳米粒子表面生成一层聚合物用于保护纳米粒子,并引入N,N-(双羧甲基)-L-赖氨酸功能基团用于螯合金属离子,从而实现固定化金属离子亲和作用。以α-酪蛋白作为实验模型,用高效液相色谱-质谱研究了螯合不同金属离子的发光纳米粒子对磷酸化蛋白的识别作用。结果表明,螯合了Ti⁴⁺金属离子的发光二氧化硅FITC@SiO₂纳米粒子对α-酪蛋白酶解液中的磷酸化肽段的富集作用最强。利用这种发光二氧化硅FITC@SiO₂纳米粒子对磷酸化肽段的特异性识别性能,可用于Western Blot实验中标记磷酸化蛋白的条带。结果显示,α-酪蛋白的电泳条带可以被亲和发光二氧化硅FITC@SiO₂纳米粒子标记,而作为对照的牛血清白蛋白则没有被标记。     

基于姜黄素负载的上转换纳米传感体系测定生物样品中的铜离子

通过高温共沉淀法制备了发光效率高、形貌规则、粒径均一的上转换纳米粒子；采用反相微乳法合成二氧化硅壳层(SiO₂)，实现上转换纳米粒子从油相到水相的转移；将介孔二氧化硅壳层(mSiO₂)包覆在上转换纳米粒子表面，荧光响应分子姜黄素被负载在m SiO₂的孔道中。基于荧光共振能量转移的原理，构建“Turn on”纳米传感体系，并用于Cu²⁺的检测，检测线性范围为10～50μmol/L，检出限为0.5μmol/L。本方法可实现大鼠血清样品中Cu²⁺的检测。     

孔蛋白-磷脂仿生膜的葡萄糖氧化酶电化学

采用孔蛋白（MspA）和双肉豆蔻磷脂酰胆碱（DMPC）在玻碳（GC）基底表面成功构建有仿生特性的纳米通道膜,同时将葡萄糖氧化酶（GOD）修饰于膜上. 使用循环伏安法研究GOD/MspA-DMPC/GC电极的GOD直接电化学过程以及其对氧气和葡萄糖的响应. 研究发现,MspA与DMPC形成的仿生纳米通道膜内,GOD在接近生物体系FAD/FADH标准电位处实现了自身两质子、两电子表面控制的电化学反应. MspA与DMPC的仿生纳米通道膜体系为GOD提供了理想活性环境.     

树枝状介孔二氧化硅的研究进展

介绍了树枝状介孔二氧化硅的三种合成方法,分别是微乳液合成、两相界面合成及球形胶束自组装合成法,为精确调节树枝状介孔二氧化硅的结构,探讨了不同方法可能的形成机理。由于球形胶束自组装合成法的绿色经济,重点讨论了球形胶束自组装合成法的发展及形成机理。介绍了树枝状介孔二氧化硅纳米材料在催化和生物医学方面的应用效果,并对树枝状介孔二氧化硅的合成方法和在催化、生物医学和能源领域的应用前景进行了展望。     

具有可控分散性的不同粒径氨基酸双功能化介孔二氧化硅纳米颗粒

通过表面活性剂,共结构导向剂（CSDAs）和硅源的自组装合成了具有分散性的不同粒径氨基酸双功能化介孔二氧化硅纳米颗粒. 通过表面活性剂头部与带相反电荷的CSDAs之间的静电相互作用使氨基和羧基基团均匀排列在介孔孔道表面. 通过调节助溶剂或分散剂的加入量来控制颗粒粒径,调节合成溶液pH改变纳米颗粒表面羧基和氨基基团的电荷切换性及其量来控制颗粒的分散性.     

自下而上法制备金-介孔二氧化硅复合纳米管用作还原4-硝基苯酚的催化剂（英文）

采用自下而上方法制备了金-介孔二氧化硅复合纳米管,其中金纳米粒子作为催化剂嵌在介孔二氧化硅纳米管管壁内侧.金纳米颗粒的团聚、脱落和晶粒尺寸生长都可以被有效限制,而且催化剂负载量和尺寸大小均可实现简单控制.管壁中的介孔孔道、纳米管末端开口以及一维中空管道可以协同促进反应物扩散,从而提高4-硝基苯酚还原反应活性.循环实验证明这种复合纳米管催化剂具有良好的可重复使用性,而且在反应过程中未出现金纳米粒子脱落或团聚现象.     

Reagentless Glucose Biosensor Based on the Direct Electrochemistry of Glucose Oxidase on Carbon Nanotube‐Modified Electrodes

The direct electrochemistry of glucose oxidase (GOD) was revealed at a carbon nanotube (CNT)‐modified glassy carbon electrode, where the enzyme was immobilized with a chitosan film containing gold nanoparticles. The immobilized GOD displays a pair of redox peaks in pH 7.4 phosphate buffer solutions (PBS) with the formal potential of about ?455 mV (vs. Ag/AgCl) and shows a surface‐controlled electrode process. Bioactivity remains good, along with effective catalysis of the reduction of oxygen. In the presence of dissolved oxygen, the reduction peak current decreased gradually with the addition of glucose, which could be used for reagentless detection of glucose with a linear range from 0.04 to 1.0 mM. The proposed glucose biosensor exhibited high sensitivity, good stability and reproducibility, and was also insensitive to common interferences such as ascorbic and uric acid. The excellent performance of the reagentless biosensor is attributed to the effective enhancement of electron transfer between enzyme and electrode surface by CNTs, and the biocompatible environment that the chitosan film containing gold nanoparticles provides for immobilized GOD.     

New approach to the immobilization of glucose oxidase on non-porous silica microspheres functionalized by (3-aminopropyl)trimethoxysilane (APTMS)

The immobilization and encapsulation of glucose oxidase (GOD) onto the mesoporous and the non-porous silica spheres prepared by co-condensation of tetraethylorthosilicate (TEOS) and (3-aminopropyl)trimethoxysilane (APTMS) in the water-in-oil (W/O) emulsion system were studied. The terminal amine group was used as the important functionality for GOD immobilization on the silica substrate. When only TEOS is used as a silica source, the disordered mesoporous silica microspheres are obtained. As the molar ratio of APTMS to TEOS (R_AT) increases, the surface area and pore volume of the silica particles measured by nitrogen adsorption and desorption method and SEM decrease rapidly. Particularly, the largest change of the surface morphology is observed between R_AT = 0.20 and R_AT = 0.25. The amount and the adsorption time of immobilized enzyme were measured by UV spectroscopy. About 20 wt% of GOD was immobilized into the silica substrates above R_AT = 0.60 and was completely adsorbed into the substrate of R_AT = 0.80 with lapse of 4 h after addition. In the measurement of the thermal stability, GOD dissolved in buffer solution loses nearly all of its activity after 30 min at 65 °C. In contrast, GOD immobilized on the surface-modified silica particles still retains about 90% of its activity after the same treatment. At this temperature, the immobilized glucose oxidase retained half of its initial activity after 4 h. It is shown that the suitable usage of functionalizing agent like APTMS as well as the control of surface morphology is very important on the immobilization of enzyme.     

Direct electrochemistry of glucose oxidase immobilized on a hexagonal mesoporous silica-MCM-41 matrix

The direct electrochemistry of glucose oxidase (GOD) immobilized on a hexagonal mesoporous silica modified glassy carbon electrode was investigated. The adsorbed GOD displayed a pair of redox peaks with a formal potential of -417 mV in 0.1 M pH 6.1 phosphate buffer solution (PBS). The response showed a diffusion-controlled electrode process with a two-electron transfer coupled with a two-proton transfer reaction process. GOD immobilized on a hexagonal mesoporous silica retained its bioactivity and stability. In addition, the immobilized GOD could electrocatalyze the oxidation of glucose to gluconlactone by taking ferrocene monocarboxylic acid (FMCA) as a mediator in N(2) saturated solutions, indicating that the electrode may have the potential application in biosensors to analyze glucose. The sensor could exclude the interference of commonly coexisted uric acid, p-acetaminophenol and ascorbic acid and diagnose diabetes very fast and sensitively. This work demonstrated that the mesoporous silica provided a novel matrix for protein immobilization and the construction of biosensors.     

Preparation of GOD/Sol‐Gel Silica Film on Prussian Blue Modified Electrode for Glucose Biosensor Application

A novel amperometric glucose biosensor was fabricated by in situ incorporating glucose oxidase (GOD) within the sol‐gel silica film on a Prussian blue (PB) modified electrode. The method is simple and controllable, which combined the merits of in situ immobilizing biomolecules in sol‐gel silica film by electrochemical method and the synergic catalysis effects of PB and GOD molecules. Scanning electron microscopy (SEM) showed that the GOD/sol‐gel silica film was homogeneous with a large number of three‐dimensional nanopores, which not only enhanced mass transport, but also maintained the active configuration of the enzyme molecule and prevented the leakage of enzyme, therefore improved the stability and sensitivity of the biosensor. The fabricated biosensor showed fast response time (10 s), high sensitivity (26.6 mA cm^?2 M^?1), long‐term stability, good suppression of interference, and linear range of 0.01 mM–5.8 mM with a low detection limit of 0.94 μM for the detection of glucose. In addition, the biosensor was successfully applied to determine glucose in human serum samples.     

二茂铁功能化Fe3O4/碳纳米管/壳聚糖复合膜葡萄糖生物传感电极的研究

采用交联法制备了羧基二茂铁功能化Fe₃O₄纳米粒子（FMC-AFNPs）复合材料,并将该复合纳米材料与多壁碳纳米管（MWNTs）、壳聚糖（CS）及葡萄糖氧化酶（GOD）混合修饰于自制的磁性玻碳基底(MGC)表面,制备了GOD/FMC-AFNPs/MWNTs/CS复合膜生物传感器电极. 实验结果表明,FMC-AFNPs复合材料有效地克服了二茂铁在电极表面的泄漏,且FMC-AFNPs/MWNTs/CS复合膜良好的生物兼容性较大地改善了固定化GOD的生物活性. MWNTs具有良好的导电性和大比表面积,在修饰膜内可作为电子传递“导线”,极大地促进电极的电子传递速率,提高电极的电催化活性和灵敏度. 该电极的葡萄糖检测的线性范围为1.0×10^-5 ~ 6.0×10^-3 molL^-1,检测限为3.2×10^-6 mmolL^-1（S/N=3）,表观米氏常数为5.03×10^-3 mmolL^-1,且有较好的稳定性和重现性.     

Glucose biosensor enhanced by nanoparticles

Glucose biosensors have been formed with glucose oxidase (GOD) immobilized in composite immobilization membrane matrix, which is composed of hydrophobic gold, or hydro-philic gold, or hydrophobic silica nanoparticles, or the combination of gold and silica nanoparticles, and polyvinyl butyral (PVB) by a sol-gel method. The experiments show that nanoparticles can significantly enhance the catalytic activity of the immobilization enzyme. The current response can be increased from tens of nanoamperometer (nA) to thousands of nanoamperometer to the same glucose concentration, and the electrodes respond very quickly, to about 1 min. The function of nanoparticles effect on immobilization enzyme has been discussed.     

基于Dy_2(MoO_4)_3-AuNPs复合纳米材料的葡萄糖生物传感器

采用水热法合成了纳米材料钼酸镝[Dy_2(MoO_4)_3],并制备了Dy_2(MoO_4)_3-AuNPs复合材料,利用该复合材料固定葡萄糖氧化酶(GOD)构建了葡萄糖生物传感器.通过透射电子显微镜(TEM)、紫外-可见光谱(UV-Vis)和能谱分析(EDS)等手段对所制备的材料进行了表征,并利用电化学阻抗谱(EIS)和循环伏安(CV)曲线研究了该传感器的电化学性能.结果表明,Dy_2(MoO_4)_3-AuNPs复合材料具有较好的生物相容性,能增强固定化的GOD的生物活性,并促进GOD在电极表面的电子传递速率;该传感器在葡萄糖浓度为0.01~1.0 mmol/L范围内葡萄糖浓度与响应电流呈较好的线性关系,最低检出限为3.33μmol/L(S/N=3),该生物传感器还具有较好的稳定性和重现性.     

Novel Composite of Multiwalled Carbon Nanotubes and Gold Nanoparticles Stabilized by Chitosan and Hydrophilic Ionic Liquid for Direct Electron Transfer of Glucose Oxidase

A novel composite was fabricated through dispersing multiwalled carbon nanotubes (MWNTs) in gold nanoparticle (GPs) colloid stabilized by chitosan and ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium tetrafluoroborate, BMIMBF₄). Transmission electron microscopy (TEM) experiment showed that the GPs highly dispersed on the MWNTs probably due to the electrostatic interaction among GPs, MWNTs and the imidazolium cation of BMIMBF₄. X‐ray photoelectron spectroscopy (XPS) indicated that thus‐formed gold nanostructure was mediated by BMIMBF₄. When glucose oxidase (GOD) was immobilized on the composite (MWNTs‐GPs) its ultraviolet‐visible absorption spectrum kept almost unchanged. The immobilized GOD coated glassy carbon electrode (GOD/MWNTs‐GPs/GC) exhibited a pair of well‐defined peaks in 0.10 M pH 7.0 phosphate buffer solution (PBS), with a formal potential of ?0.463 V (vs. SCE). The electrochemical process involved two‐electron transfer. The electron transfer coefficient was ca.0.56 and the electron transfer rate constant was 9.36 s^?1. Furthermore, the immobilized GOD presented good catalytic activity to the oxidation of glucose in air‐saturated PBS. The K_m and I_m values were estimated to be 13.7 μM and 0.619 μA. The GOD/MWNTs‐GPs/GC electrode displayed good stability and reproducibility.     

Direct Electrochemistry of Glucose Oxidase Immobilized on Titanium Carbide‐Au Nanoparticles‐Fullerene C60 Composite Film and Its Biosensing for Glucose

The direct electrochemistry of glucose oxidase (GOD) immobilized on the designed titanium carbide‐Au nanoparticles‐fullerene C₆₀ composite film modified glassy carbon electrode (TiC‐AuNPs‐C₆₀/GCE) and its biosensing for glucose were investigated. UV‐visible and Fourier‐transform infrared spectra of the resulting GOD/TiC‐AuNPs‐C₆₀ composite film suggested that the immobilized GOD retained its original structure. The direct electron transfer behaviors of immobilized GOD at the GOD/TiC‐AuNPs‐C₆₀/GCE were investigated by cyclic voltammetry in which a pair of well‐defined, quasi‐reversible redox peaks with the formal potential (E^0′) of ‐0.484 V (vs. SCE) in phosphate buffer solution (0.05 M, pH 7.0) at the scan rate of 100 mV·s^?1 were obtained. The proposed GOD modified electrode exhibited an excellent electrocatalytic activity to the reduction of glucose, and the currents of glucose reduction peak were linearly related to glucose concentration in a wider linearity range from 5.0 × 10^?6 to 1.6 × 10^?4 M with a correlation coefficient of 0.9965 and a detection limit of 2.0 × 10^?6 M (S/N = 3). The sensitivity and the apparent Michaelis‐Menten constant (K_M^app) were determined to be 149.3 μA·mM^?1·cm^?2 and 6.2 × 10^?5 M, respectively. Thus, the protocol will have potential application in studying the electron transfer of enzyme and the design of novel electrochemical biosensors.     

纳米增强型毛细管酶柱用于葡萄糖液滴生物传感器的研究

葡萄糖的检测在临床医学以及食品工业等领域中十分重要.以往的检测方法主要包括化学发光法_{[1]、吸光光度法[2]、电化学法[3]和荧光法[4]等.固定化酶柱的制作是发展葡萄糖传感器的关键技术之一.传统的固定化方法主要是将具有生物活性的酶通过物理吸附、共价键合和交联的方法固定于载体基质上或包埋于有机聚合物的基质中.近期研究[5,6]表明,采用溶胶凝胶(Sol-gel)法将蛋白质和酶等生物活性物质包埋于无机陶瓷或玻璃材料内,保持生物组分的活性,且SiO2作为基质材料具有较好的坚固性、抗磨性、化学惰性以及高的光稳定性和透过性,但目前该法多用于电化学型生物传感器[7,8].本文利用纳米颗粒的比表面积大和吸附能力强等特点,将酶吸附在SiO2纳米颗粒表面,用易成膜的聚乙烯醇缩丁醛(PVB)作辅助基质在毛细管上固定酶,并采用分立式酶柱,克服了以往混合型酶柱普遍存在的酶促效率不高和使用寿命较短的局限性.所制得的酶柱具有表面反应活性高、表面活性中心多和催化效率高等特点.结合自行设计的液滴光化学传感装置[9,10],建立了一种高效、快速、微量的葡萄糖实时检测方法.}