表面相变及Pt负载的BiOBr纳米片的协同光催化效应

通过热处理手段考察了BiOBr纳米片的表面相变过程。通过XRD,Raman,SEM,TEM,UV-Vis-DRS等手段对不同热处理温度下样品的结构进行表征。结果表明,高温热处理下(≥400℃),BiOBr相向Bi24O31Br10相转变,可形成BiOBr/Bi24O31Br10异质结。通过气相乙醛的降解,并与商用P25 TiO2做比较来评估催化剂的光催化性能,测得活性顺序为:P25 TiO2BiOBrBiOBr/Bi24O31Br10。能带结构分析可知BiOBr与Bi24O31Br10间形成I型异质结不利于电荷分离,因而活性降低。然而,当同样条件下于上述催化剂表面负载Pt后,测得光催化活性顺序为:(BiOBr/Bi24O31Br10)-PtBiOBr-PtP25 TiO2-Pt。(BiOBr/Bi24O31Br10)-Pt的最高活性归因于BiOBr/Bi24O31Br10异质结与Pt负载的协同分离光生载流子过程,即与BiOBr/Bi24O31Br10界面的光生空穴转移,BiOBr/Pt及Bi24O31Br10/Pt界面的光生电子转移、累积及开启双电子还原O2的一系列过程有关。     

钛酸铋系化合物的光催化性能研究

采用化学溶液分解法制备了钛酸铋化合物: Bi₁₂TiO₂₀, Bi₄Ti₃O₁₂和Bi₂Ti₂O₇, 并采用XRD表征了其结构. 用TEM观察发现其平均粒径＞100 nm, UV-Vis漫反射谱测定显示它们在可见光区均呈现极强的吸收特征. 紫外光照射下甲基橙的光催化降解脱色实验表明, 三种钛酸铋化合物均具有较强的光催化活性, 其中, Bi₁₂TiO₂₀的光催化活性最强, 几乎与P-25相同. 钛酸铋化合物光催化性能的不同在于它们具有不同的晶相结构和电子结构.     

Bi2Ti2O7/TiO2/Bi4Ti3O12多异质结的构筑及其增强的可见光催化性能

以静电纺丝技术制备的TiO₂纳米纤维为基质,硝酸铋为铋源,KOH为矿化剂,成功制备了多异质结Bi₄Ti₃O₁₂/TiO₂/Bi₂Ti₂O₇复合纳米纤维光催化剂。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外可见漫反射光谱(UV-Vis DRS)等一系列表征,对其物相组成、微观形貌和光学性质等进行分析。结果表明： TiO₂纳米纤维的介入,将Ⅰ型异质结Bi₂Ti₂O₇/Bi₄Ti₃O₁₂分离为2个Ⅱ型异质结Bi₂Ti₂O₇/TiO₂和Bi₄Ti₃O₁₂/TiO₂。Bi₂Ti₂O₇、Bi₄Ti₃O₁₂和TiO₂三者的协同作用,有效提高了可见光吸收能力,改变了光生载流子的传输路径,降低了光生电子与空穴的复合几率,从而获得高效的光催化降解CH₃CHO性能。可见光照8 h,Bi₄Ti₃O₁₂/TiO₂/Bi₂Ti₂O₇复合纳米纤维对CH₃CHO的降解率达到87.1%。     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附-脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

Ce掺杂Bi2MoO6/TiO2纳米纤维异质结的制备及可见光催化性能

以静电纺丝技术制备的TiO₂纳米纤维为基质,通过溶剂热法制备了异质结型稀土Ce掺杂Bi₂MoO₆/TiO₂复合纳米纤维。利用X射线衍射（XRD）、扫描电子显微镜（SEM）、X射线光电子能谱（XPS）、透射电镜（TEM）、紫外-可见漫反射光谱（UV-Vis DRS）以及荧光光谱（PL）等分析测试手段对样品的物相、形貌和光学性能等进行表征。以罗丹明B为模拟有机污染物,研究了样品的可见光催化性能。结果表明：在稀土掺杂样品中,Ce离子进入Bi₂MoO₆晶格,部分取代Bi³⁺,导致晶胞膨胀,晶格畸变,形成缺陷;与TiO₂复合形成异质结,有利于光生电荷的产生、转移和有效分离,从而提高TiO₂纳米纤维的光催化活性。可见光照射180 min,罗丹明B的降解率达到95.1%。经5次循环光催化降解活性基本不变,样品具有良好的光催化稳定性。     

Pt/SrZr0.95Y0.05O3-TiO2-xNx复合催化剂的制备及模拟太阳光催化产氢活性研究

利用共沉淀法和固相法制备出SrZr_0.95Y_0.05O₃微粒,采用溶胶包覆法使其与含氮TiO₂溶胶复合,并原位光沉积Pt颗粒组装成异质结复合催化剂,采用XRD、TG-DTA、紫外可见漫反射光谱(UV-Vis DRS)和荧光光谱(FS)等技术对其进行了表征和分析,以草酸为牺牲剂,模拟太阳光下光催化产氢为探针,评价了催化剂的光催化活性。研究了不同氮源剂、烧结温度、载铂含量对催化剂光催化产氢活性的影响。结果表明,在模拟太阳光照射下,单独的SrZr_0.95Y_0.05O₃和TiO₂几乎不产生氢气;而将两者采用溶胶包覆法复合并掺氮后,所制备出的复合催化剂表现出一定程度的产氢活性,在氮源剂为三乙胺、400 ℃焙烧下具有最佳的产氢活性,催化活性的提高源于复合催化剂中形成的异质结抑制了光生载流子的快速复合以及氮掺杂引起对可见光的响应;进一步负载铂后,其产氢量得到大幅度的提高,其最佳负载量为1wt%,6 h内产氢量达到12.5 mmol,是未负载的样品的22倍多,这是由于铂负载进一步抑制了光生载流子的复合,从而大大地提高了光催化活性。     

Bi2MoO6/BiVO4异质结的水热合成和可见光催化活性

采用一步水热法制备Bi₂MoO₆/BiVO₄复合光催化剂. 利用X 射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、高分辨透射电子显微镜(HRTEM)等手段对其晶体结构和微观结构进行了表征. 结果表明, Bi₂MoO₆纳米粒子沉积在BiVO₄纳米片表面从而形成异质结结构. 紫外-可见漫反射光谱(UV-Vis DRS)表明所制备的Bi₂MoO₆/BiVO₄异质结较纯相Bi₂MoO₆和BiVO₄对可见光吸收更强. 由于形成异质结结构及其光吸收性能使Bi₂MoO₆/BiVO₄ 光催化活性有较大提高. 可见光下(λ>420 nm)光催化降解罗丹明B (RhB)实验结果表明,Bi₂MoO₆/BiVO₄光催化活性较纯相Bi₂MoO₆和BiVO₄高. Bi₂MoO₆/BiVO₄样品光催化性能提高的原因是Bi₂MoO₆和BiVO₄形成异质结, 从而有效抑制光生电子-空穴对的复合, 增大了可见光吸收范围及比表面积.     

Bi2WO6量子点(QDs)修饰Bi2MoO6-xF2x异质结的构筑及其催化活性增强机理

采用简单沉积-沉淀法合成了Bi₂WO₆@Bi₂MoO_6-xF_2x（BWO/BMO6-xF2x）异质结,借助XRD、XPS、TEM、SEM、EDS、UV-Vis-DRS、PC和EIS等测试技术对其组成、形貌、光吸收特性和光电化学性能等进行系统表征,并以模型污染物罗丹明B（RhB）的光催化降解作为探针反应来评价Bi₂WO₆@Bi₂MoO_6-xF_2x异质结的光催化活性增强机制。形貌分析表明,所得Bi₂MoO₆微球由大量厚度为20~50 nm的纳米片组成;FE-SEM和HR-TEM分析表明,尺寸约为10 nm的Bi₂WO₆量子点均匀沉积在Bi₂MoO_6-xF_2x微球表面,形成新颖的Bi₂WO₆@Bi₂MoO_6-xF_2x异质结;与纯Bi₂MoO₆或者Bi₂WO₆相比,1∶1Bi₂WO₆@Bi₂MoO_6-xF_2x异质结表现出更好的光催化活性和光电流性质,其对RhB光催化降解的表观速率常数分别为纯BMO和BWO的6.4和11.6倍。PC和EIS图谱分析表明,Bi₂WO₆量子点表面沉积显著提高Bi₂MoO_6-xF_2x光生电子/空穴的分离效率和迁移速率;活性物种捕获实验证明了·O₂^-和h⁺是主要的活性物种。根据实验结果,探讨了F^-掺杂和Bi₂WO₆量子点之间的协同效应对Bi₂MoO₆的光催化活性的影响机制。     

一锅法制备S型异质结光催化剂Fe2O3/Fe2TiO5及其高效降解有机污染物性能

首次采用简单的一锅法制备了Fe₂O₃/Fe₂TiO₅异质结纳米材料。构建S型异质结后,与纯的Fe₂O₃和Fe₂TiO₅相比,Fe₂O₃/Fe₂TiO₅复合材料表现出更高的光催化降解速率和效率。经过2.5 h的光照后,Fe₂O₃/Fe₂TiO₅可以降解接近100%的亚甲基蓝（MB）。在Fe₂O₃/Fe₂TiO₅复合材料中,Fe₂O₃和Fe₂TiO₅之间形成了内建电场,可以促进光生电子-空穴对的分离。因此,具有更高能量的Fe₂TiO₅导带中的电子和具有更高能量的Fe₂O₃价带中的空穴可以得到有效的保留,从而使它们更加有效地扩散到催化剂表面,并参加降解反应。此外,Fe₂O₃/Fe₂TiO₅复合材料具有很好的光催化稳定性。     

Near infrared study of aqueous rare-earth ethylsulfates

The near infrared spectra of aqueous solutions of the ethylsulfates of La, Nd, Gd, Tb, Er, Yb, Lu, Y, and Na have been determined from about 0.2 mol-dm^–3 to nearly saturation. The extinction coefficients of water have been calculated taking into account the absorption of ethylslfate anions determined in separate experiments. Their values appeared to be nearly the same as that of pure water. The relative contents of free OH groups in 0.5 and 0.7M solutions have been estimated from the absorbances at 1160 nm. They were lower in solutions of the heavy rare-earth ethylsulfates (Tb, Er, Yb, Lu) than in equimolar solutions of the lighter ones (La, Nd), confirming our previous view that secondary hydration of the heavy trivalent rare-earth cations is distinctly stronger than that of the lighter ones. A comparison of the spectra of these aqueous ethylsulfates with those of perchlorates shows that the structure-breaking ability of the C₂H₅SO ₄ ^– ion is much smaller than that of perchlorate anion.     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

Li_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3,Na_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3的离子交换研究

研究了在不同温度下的NaNO3和AgNO3水溶液中Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3离子交换行为.实验表明Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3均显示出了高选择性与Na+和Ag+进行离子交换的特征,且对Ag+的选择性高于Na+.升高温度可显著提高Ag/Li和Ag/Na的交换反应速度.     

电感耦合等离子体光谱法测定铜冶炼烟尘中锌

本实验介绍了电感耦合等离子体光谱法测定铜冶炼烟尘中锌含量的分析方法。针对样品碳,硅含量高的特点,有针对性的研究了样品的消解方法,确定采用盐酸、硝酸、氢氟酸、高氯酸对铜冶炼烟尘样品进行消解。同时进行了干扰试验,确定样品中高含量的铜,铅,砷等对样品测定结果没有影响。并对仪器的工作参数进行了优化。方法检出限为为0.011 mg/L,测定下限为0.019 mg/L,3个样品的相对标准偏差在0.54%~0.92%之间,加标回收率在96%~101.14%之间。该方法样品消解完全,流程短,操作简单,快速,测定准确度高,可以满足铜冶炼烟尘中锌含量的测定。     

Near infrared study of aqueous lanthanide perchlorates

The near infrared spectra of water in aqueous solutions of La(ClO₄)₃, Pr(ClO₄)₃, Nd(ClO₄)₃, Gd(ClO₄)₃, Er(ClO₄)₃, Yb(ClO₄)₃, Lu(ClO₄)₃, and NaClO₄ have been measured in the concentration range from 0.3 to 2.5 mol-dm^–3, at 25°C. The relative contents of free OH groups in the 1.0, 1.6, and 2.2M solutions have been calculated from extinction coefficients for water at 1160 nm. They increase with increasing salt concentration and are greater in solutions of the lighter lanthanide perchlorates at any fixed molarity. The results are discussed in terms of the stoichiometry and structure of hydrated cations of trivalent lanthanides.     

Syntheses and characterization of two oxoborates, (Pb3O)2(BO3)2MO4 (M=Cr, Mo)

Two oxoborates, (Pb₃O)₂(BO₃)₂MO₄ (M=Cr, Mo), have been prepared by solid-state reactions below 700 °C. Single-crystal XRD analyses showed that the Cr compound crystallizes in the orthorhombic group Pnma with a=6.4160(13) Å, b=11.635(2) Å, c=18.164(4) Å, Z=4 and the Mo analog in the group Cmcm with a=18.446(4) Å, b=6.3557(13) Å, c=11.657(2) Å, Z=4. Both compounds are characterized by one-dimensional chains formed by corner-sharing OPb₄ tetrahedra. BO₃ and CrO₄ (MoO₄) groups are located around the chains to hold them together via Pb–O bonds. The IR spectra further confirmed the presence of BO₃ groups in both structures and UV–vis diffuse reflectance spectra showed band gaps of about 1.8 and 2.9 eV for the Cr and Mo compounds, respectively. Band structure calculations indicated that (Pb₃O)₂(BO₃)₂MoO₄ is a direct semiconductor with the calculated energy gap of about 2.4 eV.     

Decomposition of P2S2N4(Si(CH3)3)4A12C14 as Studied by FT-Raman and Quantum Chemistry Means

The dimeric title compound decomposes upon heating to give the monomer and desulphurized monomer as shown by FT-Raman and quantum chemical means.     

Microstructures of Some Bi-W-Nb-O Phases

Microstructures of three Bi-W-Nb-O phases have been examined by using high-resolution transmission electron microscopy. Bi₁₇W₂Nb₃O₃₉ and Bi₁₇WNb₃O₃₆ have incommensurate superstructures derived from the defect fluorite-type δ-Bi₂O₃ and can be regarded as intermediate phases between the type II solid solutions in the Bi-Nb-O and Bi-W-O systems. Bi₈W₂Nb₂O₂₃ has a Bi₂WO₆-like subunit cell with a stepped superstructure. Formation mechanisms of various superstructures are discussed.     

Reactivity of Binary Mixtures of La(III) Oxide and Cu(II) Oxalate or Nitrate and Synthesis of La(III) Cuprate

Reactivity of mixtures of La(III) oxide and Cu(II) oxalate/nitrate in hydrated as well as anhydrous state was studied using TG, DTA and XRD. Cu(II) oxide formed in the endothermic decomposition of mixture containing hydrated Cu(II) nitrate and La(III) oxide could not form La₂CuO₄ while Cu(II) oxide formed in the exothermic decomposition of mixture containing hydrated/anhydrous Cu(II) oxalate and La(III) oxide reacts with La(III) oxide and develops the phases CuLaO₃ and La₂CuO₄. The maximum reactivity with respect to the formation of La₂CuO₄phase was observed in mixture containing anhydrous Cu(II) oxalate. This revised version was published online in July 2006 with corrections to the Cover Date.     

Theoretical study of the triplet excited state of PtPOP and the exciplexes M-PtPOP (M = Tl, Ag) in solution and comparison with ultrafast X-ray scattering results

The [Pt₂(H₂P₂O₅)₄]⁴⁻ ions in the ground and excited states and the excited-state complexes M-[Pt₂(H₂P₂O₅)₄]³⁻ and M₂-[Pt₂(H₂P₂O₅)₄]²⁻ (M = Ag, Tl) were studied in solution with various density functional theory (DFT) functionals from Gaussian 09 and Amsterdam Density Functional (ADF) programs. Calculated results were compared with ultrafast X-ray solution scattering data. Time dependent DFT (TD-DFT) calculations with the B3PW91 functional and unrestricted open shell calculations with the mPBE functional produce good agreement with the experimental results. Compared to gas phase calculations, the surrounding solvent is found to play an important role to shorten the Pt-Pt and M-Pt (M = Ag, Tl) bond lengths, lowering the molecular orbital energies and influences the molecular orbital transitions upon excitation, which stabilizes the excited transient molecules in solution.