pH/Cl-复合探针技术对钢筋混凝土电化学除氯的原位检测

采用恒电流法电化学除氯处理受氯离子污染的钢筋混凝土试样,并用pH/Cl^-复合探针原位检测电化学除氯过程钢筋混凝土不同位置孔隙液的氯离子含量与pH值分布,同时用线性极化曲线和交流阻抗谱图等电化学技术考察钢筋的腐蚀性能,探讨电化学除氯过程的混凝土微环境和钢筋腐蚀速率. 研究结果表明：在电化学除氯过程,混凝土孔隙液的氯离子浓度逐降,而pH值在初期略有升高,随之其pH值略降;电化学除氯施加的阴极电流,使钢筋处于阴极极化状态而得到保护;除氯停止（即退极化）后钢筋的腐蚀电位明显正移,腐蚀电流降低,极化电阻升高,表明电化学除氯能改善钢筋的腐蚀环境,降低钢筋的腐蚀速率.     

Fabrication of IrO2 H+ Sensor and Its Application in the Measurement of pH at Steel/Concrete Interface

Corrosion of steel reinforcement is the most serious threat to the service life of modem reinforced concrete structure and the corrosion behavior of the steel reinforcement has a close dependence on the chemical environment at the steel/concrete interface. Among all the species which can affect the corrosion rate, H⁺ is of the greatest influence on the stability of the steel bars. However, the in-situ measurement of pH value at steel/concrete interface is still underway. In this paper fabrication of Ir oxide electrode which serves as the pH probe working at the steel/concrete interface was explored.     

动力学分光光度法快速测定高pH值

传统的pH值玻璃电极传感器在pH 1·0~12·0的范围内具有很好的准确性,但在pH<1·0和pH>12·0的条件下会产生“酸误”和“碱误”[1-3]。氢氧化钠是最常用的化学试剂之一,因此它的准确测定在各种工业过程如产品的质量控制,环境污染控制,以及设备腐蚀控制过程中等具有重要作用。已     

Fluorescent pH probes for alkaline pH range based on perylene tetra-(alkoxycarbonyl) derivatives

The pH detection in the alkaline range is particularly important in many fields such as leather processing, waste water treatment, paper industry, and metal mining and finishing. Compared with traditional analysis methods such as colorimetric sensors and electrochemical sensors, the fluorescence and colorimetric probes for pH measurements have attracted much more attention due to their advantages of high sensitivity, excellent selectivity, noninvasiveness, low cost, fast response time, the possibility of continuously measurement, etc. However, there are few fluorescent probes fiting for alkaline pH monitoring. Acturally, the design and synthesis of them were more significant for new probes producing. In this study, the design, synthesis, and practical application of two novel fluorescent pH probes for alkaline pH assay were discussed. Both of the two probes were derived from perylene tetra-(alkoxycarbonyl). The red or blue shift of the absorption/fluorescence spectrum was caused by the introduction of electron donor amino or oxygen ring in the bay region. Due to electronic separation of the OH group from the electron-withdrawing core, the probes have high pKa values and cover the pH range from 8 to 12. They exist in either fluorescent acid form or non-fluorescent basic form. It was investigated that the amino substituent at bay region had a higher pKa value than O-heterocyclic annulated perylene, which showed that the adjustable pKa value could be achieved by the modification of electron withdrawing groups. The probes would have a wide use for testing strips measurements and monitoring pH changes in concrete.     

Effect of drop size on the degradation of VX in concrete

The effect of drop size on the degradation rate of VX, O-ethyl S-[2-(diisopropylamino)ethyl]methylphosphonothioate, in fresh concrete has been examined using (31)P NMR. Drops of neat VX, ranging in size from 4 microL to 0.2 microL, applied to small concrete coupons (8 mm x 15 mm) were observed to degrade at different rates, with the 1 microL and smaller drops reacting in less than 4 days, and the larger droplets reacting in less than 11 days. Additionally, 4 microL VX predissolved in hexane to evenly spread it over the concrete coupon likewise reacted faster, degrading in less than 5 days. The fresh concrete, less than 2 months old, exhibited significantly faster VX degradation for all drop sizes than that observed for "aged" concrete in a previous study where VX persisted for months. The enhanced reactivity of the "fresh" concrete for VX was maintained for at least a 1-year period. The pH of water containing crushed "fresh" and "aged" concrete was 10.0 and 9.0, respectively. The higher pH of the "fresh" concrete is one reason for its enhanced reactivity toward VX. An additional contribution to the enhanced reactivity of the "fresh" concrete is suggested by the increased mobility of its sorbed VX as evidenced by its significantly narrower peak in (31)P NMR spectra.     

Decontamination of uranium-contaminated concrete

This study examined the decontamination method by washing with nitric acid for uranium contaminated concrete pieces produced from the decommissioning of a uranium conversion plant and evaluated the amount of waste sludge generated from the treatment. In addition, carbonate solution, nitric acid and sulfuric acid were used as the extraction reagents for the uranium, and their efficiencies were also compared. For concrete pieces coated with and without epoxy, the separation method of cement paste from aggregates was preferable to the leaching of uranium from concrete because of its simpler decontamination process. When concrete pieces with epoxy were heated for 2 h at 400 °C, pulverized and sequentially washed with 0.1, 2.0 and 1.0 M of nitric acid, their radioactivity reached below the limit value of uranium for self-disposal. Unlike previous results, uranium dissolved in 1 and 2 M sulfuric acid solutions was not removed by strong anion exchange resins such as IRA 910 and Ag1×8.     

Remediation of soil/concrete contaminated with uranium and radium by biological method

Biological method was studied for remediation of soil/concrete contaminated with uranium and radium. Optimum experiment conditions for mixing ratios of penatron and soil, and the pH of soil was obtained through several bioremediations with soil contaminated with uranium and radium. It was found that an optimum mixing ratio of penatron for bioremediation of uranium soil was 1 %. Also, the optimum pH condition for bioremediation of soil contaminated with uranium and radium was 7.5. The removal efficiencies of uranium and radium from higher concentration of soil were rather reduced in comparison with those from lower concentration of soil. Meanwhile, the removal of uranium and radium in concrete by bioremediation is possible but the removal rate from concrete was slower than that from soil. The removal efficiencies of uranium and radium from soil under injection of 1 % penatron at pH 7.5 for 120 days were 81.2 and 81.6 %, respectively, and the removal efficiencies of uranium and radium from concrete under the same condition were 63.0 and 45.2 %, respectively. Beyond 30 days, removal rates of uranium and radium from soil and concrete by bioremediation was very slow.     

Applicability of dynamic change of pH in the capillary zone electrophoresis of proteins

A method to extend the separation power of CZE is described. The method is based on the separation of sample components at two different pH values during one separation run, and involves dynamic buffering of the pH inside a separation capillary by controlling the flow of H+ ions from the anodic electrode chamber. By changing the anolyte in the chamber, a dynamic pH step is generated, which proceeds rapidly along the capillary and establishes the required new pH value. The use of the method has been demonstrated by the cationic separation of a model mixture of proteins.     

Measurement of cellular stimulation through monitoring pH changes by bead injection fluorescence microscopy

This work presents a method for extracellular and intracellular pH measurements in live cells based on a combination of the bead injection (BI) technique and fluorescence microscopy. For extracellular pH measurement, cells are grown on fluorescent beads, packed into a small column by a sequential injection instrument, and fluorescence intensity from the beads stained by the indicator is recorded by a fluorescence microscope. The method is applied to quantifying carbachol stimulation of Chinese hamster ovary (CHO) cells transfected with the m1 muscarinic receptor and is verified by a glucose depletion experiment. The results yield an EC(50) value of 1 muM for carbachol, which is in reasonable agreement with the literature value 3 muM determined by an existing potentiometric technique for measuring acid release. The intracellular measurement utilizes CHO M1 cells growing on non-fluorescent beads. For this method the cells rather than the beads are stained by incubating them in a solution of the fluorescent pH indicator BCECF. The cells are also stimulated with carbachol and the intracellular pH dependent fluorescence from the cells is recorded. The results show dependence between intracellular pH changes and carbachol concentration and yield an EC(50) value of 4 muM.     

Effect of pH on the Hydrothermal Synthesis of BN Nanocrystals

Boron nitride (BN) has been synthesized using hydrothermal synthesis method. The experimental results showed that the pH value of the reaction solution has an important effect on the yield and phases of BN samples. As the pH value decreased, the content of cBN increased and the yield improved. The increase in cBN content is resulted from the conversion of oBN into cBN under hydrothermal condition, and the growth of cBN nanocrystals may due to the decrease in the reaction speed, thus the crystalline perfection of BN improved when the pH value decreased.     

Estimation of uncertainty in routine pH measurement

A procedure for estimation of measurement uncertainty of routine pH measurement (pH meter with two-point calibration, with or without automatic temperature compensation, combination glass electrode) based on the ISO method is presented. It is based on a mathematical model of pH measurement that involves nine input parameters. Altogether 14 components of uncertainty are identified and quantified. No single uncertainty estimate can be ascribed to a pH measurement procedure: the uncertainty of pH strongly depends on changes in experimental details and on the pH value itself. The uncertainty is the lowest near the isopotential point and in the center of the calibration line and can increase by a factor of 2 (depending on the details of the measurement procedure) when moving from around pH 7 to around pH 2 or 11. Therefore it is necessary to estimate the uncertainty separately for each measurement. For routine pH measurement the uncertainty cannot be significantly reduced by using more accurate standard solutions than ±0.02 pH units – the uncertainty improvement is small. A major problem in estimating the uncertainty of pH is the residual junction potential, which is almost impossible to take rigorously into account in the framework of a routine pH measurement.¹ Received: 11 August 2001 Accepted: 22 February 2002     

pH荧光纳米传感器的研制及表征

利用溶胶-凝胶技术制得了单分散性很好的二氧化硅纳米微球,通过共价偶联方式引入对pH变化敏感的荧光素异硫氰酸酯（FITC）,这种FITC功能化二氧化硅纳米微球（FITC功能化硅微球）可作为pH荧光纳米传感器。当pH值从4.0变至7.5时,荧光强度增大约30倍。该传感器灵敏度高,响应速度快,容易制备,光稳定性好,可望用于单细胞的pH分析。     

Simple Method for Stabilizing Solution pH in an Electrochemical Cell

A method is proposed for stabilizing solution pH inside an electrochemical cell. During the working electrode polarization, an electrolyte of the same composition as that of the working one, but with a different pH value is continuously added into the cell. Its pH value and rate of addition are selected so as to compensate variations in the electrolyte's acidity occurring in the cell.     

Influence of pH for the determination of serum albumin by a dye-binding method in the presence of a detergent

In the dye-binding method, the absorbance increase caused by a protein error of a pH indicator is observed only in a restricted pH range. However, this pH range in the presence of a detergent has not yet been examined. Thus, the author investigated the pH (pH(UL)) where the absorbance increase becomes zero by a calculation based on the chemical equilibrium of a protein error of a pH indicator, and by experiments using four sulfonephthalein dyes. The pH(UL) value changed only with the detergent concentration, but did not change at all due to the dye, buffer solution or protein concentrations. Although the pH(UL) value was different according to the kind of dye used, it correlated well with the pK(D) values (dissociation constant) of BPB, BCG, BCP and BTB. The characteristics of pH(UL) in the reactions of the four dyes indicated good agreement with that obtained by a calculation.     

The pH inside a swollen polyelectrolyte gel: poly(N-vinylimidazole)

The pH inside a dissolved polyelectrolyte coil or a swollen ionic polymer network is not accessible to direct measurement. It is here calculated through a simple model, based on Donnan equilibrium, counterion condensation (for charge density exceeding the critical value), and balance of mobile ions, without any assumption on the pKa of the ionizable groups. The data needed for the calculation with this model are polymer concentration, pH value in the initial solution, and pH value in the bath at equilibrium. All three can be determined experimentally by a batch method where the polymer is immersed in a different pot for each starting pH. The model is applied to a sample system, namely, chemically cross-linked poly(N-vinylimidazole) immersed in acidic baths of different pH values. The imidazole units are basic and become protonated by the acid, thus changing the pH of the initial bath. The model shows how the pH developed inside the swollen gel is several units higher than the pH of the bath at equilibrium, both with or without the correction for counterion condensation. Consequently, when the pKa of the polyelectrolyte is determined in the usual way (with the pH measured in the external bath), it gives an apparent value that is several units below the pKa determined from the actual pH inside the swollen gel at equilibrium. The inclusion of the counterion condensation decreases very slightly the polymer basicity. Surface effects and intramolecular association between protonated and unprotonated imidazole rings are discussed to explain the pKa behavior in the limit of low degree of ionization.     

Improved traceability of pH measurements

Traceability is a prerequisite for the comparability and uniformity of measurements. Although pH-measurements are carried out on a large scale in laboratory and industry, the problems involved in the traceability of pH values have not adequately been solved in the past. The comparability of pH measurements is limited, among other parameters, by the accuracy of the pH values of the standard buffer solutions used to calibrate the pH meter-electrode assemblies. The measured pH(X) value must be traceable to primary standard pH(PS) values through an unbroken chain of comparisons, all values having stated uncertainties. A new primary standard measurement device for pH is used to certify primary pH reference materials from which these secondary reference materials can be derived.     

pH位移法评定阻垢剂的阻垢性能

介绍了一种评定阻垢剂性能的新方法，即在某一pH范围内，通过测定加入阻垢剂后Ca(HCO3）2过饱和溶液的起始PH与一定时间后的稳定PH之差，根据差值的变化评定阻垢的阻垢性能，通过与国内普遍采用的评定阻垢剂性能的方法－静态阻垢法和鼓泡法的比较，证明此法简便、快捷，重现性好，可信度高。     

Measurement uncertainty in the pH measurement procedure

A measured value without even an approximate knowledge of the uncertainty is worthless. The uncertainty is part of every measured value and specification of the uncertainty is part of every analytical procedure. The uncertainty makes the value independent of its origin. The basis for estimation of the uncertainty is the "Guide to the Expression of Uncertainty in Measurement ". For some procedures, however, for example pH measurement, several problems arise in practice. This article describes a practical and inexpensive way of calculating the uncertainty of pH values.     

Secondary pH standards and their uncertainty in the context of the problem of two pH scales

Establishing a traceability route with all measurement and uncertainty relationships determined is an important aspect of traceability, and seems to be particularly striking in pH measurement. In this paper the issue of evaluation of secondary pH standards measured with reference to a primary standard in a differential cell with free diffusion type liquid junctions is considered. Relatively high uncertainty, U=0.015, has been assigned to such standards in the recent IUPAC Recommendations on pH (2001), because of a specific residual liquid-junction potential treated statistically as a contribution to the combined uncertainty. Close inspection of the problem leads to the conclusion that a correction for the residual liquid-junction potential should be applied to the measured value of a secondary pH standard. This can be considered as a correction for a known systematic effect on the traceability route. With available experimental data it is demonstrated that such a correction can reasonably be made for well-studied standard buffer systems. In this way the uncertainty associated with secondary pH standards is kept to a low level, and, what is more, the problem of two pH scales, a multi-standard scale and a single-standard scale, gains a proper solution. The need for different treatment of residual liquid-junction potentials at different levels in the measurement hierarchy is noted. Much attention is also given to rational categorization of pH standards in the hierarchy.     

Protein error of pH indicators in the presence of detergents.

The characteristics of color development due to a protein error in the dye-binding method in the presence of a non-ionic detergent has been investigated by the calculations based on the chemical equilibrium of a protein error. The calculation results were compared with those obtained using three pH indicators (Bromophenol Blue, Bromocresol Green and Bromocresol Purple) and three non-ionic detergents in the pH region from 1 to 13. In the experiments, the color development increased with the lower concentrations of the detergents, but decreased at higher concentrations. The pH where the color development reached a maximum value shifted to a higher pH as the detergent was added. These experimental results were reproduced by the calculation when the molar absorptivity of the dye-protein complex was assumed to increase due to adding the detergent. Such agreement between the experimental and the calculated results indicates that the characteristics of the color development in the dye-binding method in the presence of a non-ionic detergent can be analyzed by calculations based on the chemical equilibrium of a protein error.