Design of Micro‐interdigitated Electrodes and Detailed Impedance Data Analysis for Label‐free Biomarker Quantification

Electrical impedance based biosensing is a label‐free technique that is gaining momentum in biology/medicine. The electrical impedance, typically measured using an array of micro‐fabricated interdigitated electrode array (IDE), is a byproduct of the interaction between electric fields and target bio‐molecules/cells. In current impedance based biosensing, it has been focused on utilizing the magnitude of the impedance (|Z|) to detect/quantify bio‐molecules. There were no reports on designing IDE electrodes, sensitivity analysis and detailed impedance data analysis. To address this issue, we have designed and fabricated IDE array and performed model experiments. We have found that depending on the frequency of the external electric potential, there is a variation of electric field across the array of IDEs from first pair to last pair. We then developed impedance data analysis technique (using (|Z|) and its phase (φ)) to analyze the complex impedance data, and finally, we have utilized Warburg theoretical circuit model to calculate the capacitance and resistance of the individual IDE pairs in the constant phase impedance region. Using the capacitance values, we have developed a procedure to determine the sensitivity of the IDE array. We have found that sensitivity of the IDE array does not depend on the sample conductivity.     

Characterisation of the interdigitated electrode array with tantalum silicide electrodes separated by insulating barriers

A novel design of an interdigitated electrode array impedimetric sensor is proposed with electrode digits separated by an insulating barrier. This configuration results in that the major part of the electric current between electrodes follows close to the surface of the barrier and not through the solution thus permitting to enhance the sensitivity to possible chemical reactions on its surface. As a model system the effect of electrostatically assembled polyelectrolyte layers deposited using layer-by-layer method on the sensor impedance was studied. The sensitivity of the devices depends on the barrier height and is considerably enhanced comparing to conventional flat sensor structures. Devices may be used as a transducer for direct label-free biosensor development.     

Theory of Frequency-Dependent Polarization of General Planar Electrodes with Zeta Potentials of Arbitrary Magnitude in Ionic Media: 2. Applications and Results from Homogeneous and Array Systems of Electrodes

The expressions obtained in the previous paper for electrode polarization are applied to a homogeneous planar electrode and a planar array of electrodes used in the generation of nonuniform fields. The effective far field experienced outside the double layer is computed for both electrodes, and sample spectra are provided. The effective far field expression contains the electrode impedance and the effects of concentration polarization due to the static double layer on the electrode generated by the ζ potential. The effective far field results are compact and contain simple integrals that can be evaluated numerically.     

Electrochemical Sensor Design Using Coplanar and Elevated Interdigitated Array Electrodes. A Computational Study

The time dependent diffusion equation for an interdigitated array (IDA) of coplanar and elevated electrodes is solved numerically by extrapolation of the fully implicit method using a problem adapted space grid. The simulations are performed for IDA electrodes in generator‐collector mode. The influence of the electrode height and the height of the diffusion space on the sensitivity and the response time is investigated.     

白血病细胞酶联免疫酶催化银沉积于插指电极阵列电化学免疫分析新方法

建立了一种检测白血病细胞表面抗原的细胞酶联免疫电化学分析新方法. 该方法兼有细胞酶联免疫分析抗原、抗体结合的特异性和插指电极阵列酶催化银沉积电化学分析的灵敏性. 在聚苯乙烯微孔板中包被白血病细胞, 先后加入鼠抗人抗体及碱性磷酸酶(ALP)标记的马抗鼠抗体, ALP催化抗坏血酸磷酸酯(AAP)水解成抗坏血酸(AA), AA使银离子还原成银单质并沉积到插指电极阵列表面, 导致插指电极阵列上相邻两个梳齿导通. 通过对电导率的测定, 可实现对细胞表面抗原的高灵敏分析. 此分析方法灵敏度高(可检测出50个左右的HL-60细胞)、特异性好, 且可用于大量样品的分析, 为白血病等肿瘤疾病的早期诊断和免疫分型提供了新技术. 此外, 该方法也可用于细胞表面分子基因工程抗体活性的检测.     

Electrochemical Detection of Protons Produced in an Electrode Reaction Using Interdigitated Microarray Electrodes

This work describes the use of interdigitated array electrodes (IDAE) for proton detection. Methanol electrooxidation in sulfuric acid solution was exemplified. Reduction currents originating in the reaction product generated by methanol electrooxidation on a Pt generator electrode were observed at the Pt collector electrode, the potential of which was fixed in the hydrogen evolution region. In order to reduce the background current of hydrogen evolution, an Hg‐plated Pt collector electrode was fabricated. Compared to the Pt collector electrode, the reduction current observed at the Hg collector electrode was extremely small. The product detected was found to be a proton from the current responses observed at Pt and Hg collector electrodes.     

Electrochemical Detection of MS2 Phage Using a Bead‐based Immunoassay and a NanoIDA

A microbead based sandwich immunoassay for MS2 bacteriophage was developed using an interdigitated array (IDA) electrode with nanoscale dimensions (220 nm electrode width, 620 nm gap). The IDA was fabricated using an electron beam lithographic lift‐off technique. After an antibody‐assisted capture of MS2 using paramagnetic microbeads, a β‐galactosidase labeled secondary antibody was used to convert p‐aminophenyl‐β‐D ‐galactopyranoside (PAPG) into the redox active p‐aminophenol (PAP). Amperometric detection of PAP with IDA electrodes at +300 and ?200 mV vs. a Ag/AgCl reference electrode was used to measure the result, detecting MS2 concentrations as low as 10 ng/mL.     

Simulation of Redox‐Cycling Phenomena at Interdigitated Array (IDA) Electrodes: Amplification and Selectivity

We present Finite Element Method (FEM) simulations of interdigitated array (IDA) electrode geometries to study and verify redox selectivity and redox cycling amplification factor. The simulations provide an adequate explanation of an earlier found, but poorly understood, high amplification factor (65×) in a 1 μm‐spaced IDA microdevice. Moreover, using the FEM calculations we present selectivity measurements with IDA electrodes in a mixture of two redox species, as for example dopamine and ferricyanide. We show that it is possible to electrochemically detect dopamine in presence of the stronger reductor ferricyanide, which is impossible with direct amperometric detection, with the use of IDA electrodes with proper polarization potential of the collector electrode. Using our simulations, we show that a theoretical selectivity of dopamine over ferricyanide of 11 can be achieved.     

Polarisation-independent blue-phase liquid crystal microlens array with different dielectric layer

A fast response (sub-milliseconds) and polarisation-independent blue-phase liquid crystal (BPLC) microlens array with periodical double layer electrodes using different dielectric layers is proposed. The bottom double layer electrodes are coated with transparent and different dielectric layers to generate linearly varying electric potential from the centre to the edge, while the top planar electrode iridium tin oxide (ITO) electrode has a constant potential. As a result, gradient vertical electric fields are generated, and a gradient refractive index profile is obtained. When the applied voltage is changed, the focal length of the BPLC microlens array can be tuned from ∞ to 12.05 mm while keep a low operating voltage (~35V_rms). Besides, the driving mode (simplification driving) and fabrication process (using printing method or mold-pressing method) of the BPLC microlens array is very simple. The simulation results show that the BPLC microlens array is insensitive to the polarisation of incident light while keeping parabolic-like phase profile.     

Biohybrid microarrays – Impedimetric biosensors with 3D in vitro tissues for toxicological and biomedical screening

To investigate the effectiveness of potential anti-cancer therapeutics or therapies, efficient screening methods are required. On the one hand, multicellular 3D aggregates (spheroids) are a powerful in vitro model for simulating the in vivo situation and on the other hand, planar electrode structures are generally highly suitable for automation and parallel testing. Here, the detection of the effect of active substances on spheroids positioned on electrodes of substrate integrated electrode arrays is exemplarily investigated. As a 3D tissue model a reaggregation system of T47D clone 11 tumor cells is used. The effect of cytotoxins (DMSO, Triton X-100) on spheroids can be detected by recording the effective impedance of planar electrodes covered by spheroids. The equivalent circuit model parameter of electrodes covered by cytotoxin treated spheroids are determined from recorded impedance spectra and compared to the parameter of electrodes covered by control spheroids as well as not covered electrodes. Spheroids on electrodes mainly influence the electrode impedance in the frequency range of 10 kHz to 1 MHz. The results are discussed in view of an optimal electrode/spheroid-interface for sensing the effects of therapeutics with high sensitivity.     

Biohybrid microarrays--impedimetric biosensors with 3D in vitro tissues for toxicological and biomedical screening

To investigate the effectiveness of potential anticancer therapeutics or therapies, efficient screening methods are required. On the one hand, multicellular 3D aggregates (spheroids) are a powerful in vitro model for simulating the in vivo situation and on the other hand, planar electrode structures are generally highly suitable for automation and parallel testing. Here, the detection of the effect of active substances on spheroids positioned on electrodes of substrate integrated electrode arrays is exemplarily investigated. As a 3D tissue model a reaggregation system of T47D clone 11 tumor cells is used. The effect of cytotoxins (DMSO, Triton X-100) on spheroids can be detected by recording the effective impedance of planar electrodes covered by spheroids. The equivalent circuit model parameter of electrodes covered by cytotoxin treated spheroids are determined from recorded impedance spectra and compared to the parameter of electrodes covered by control spheroids as well as not covered electrodes. Spheroids on electrodes mainly influence the electrode impedance in the frequency range of 10 kHz to 1 MHz. The results are discussed in view of an optimal electrode/spheroid-interface for sensing the effects of therapeutics with high sensitivity.     

A new floating electrode structure for generating homogeneous electrical fields in microfluidic channels

In this article a new parallel electrode structure in a microfluidic channel is described that makes use of a floating electrode to get a homogeneous electrical field. Compared to existing parallel electrode structures, the new structure has an easier production process and there is no need for an electrical connection to both sides of the microfluidic chip. With the new chip design, polystyrene beads suspended in background electrolyte have been detected using electrical impedance measurements. The results of electrical impedance changes caused by beads passing the electrodes are compared with results in a similar planar electrode configuration. It is shown that in the new configuration the coefficient of variation of the impedance changes is lower compared to the planar configuration (0.39 versus 0.56) and less dependent on the position of the beads passage in the channel as a result of the homogeneous electrical field. To our knowledge this is the first time that a floating electrode is used for the realization of a parallel electrode structure. The proposed production method for parallel electrodes in microfluidic channels can easily be applied to other applications.     

Hydrodynamic voltammetry at an interdigitated electrode array in a flow channel: Part I. Numerical simulation

This paper describes the numerical simulation of convective diffusion at an interdigitated electrode array, consisting of multiple pairs of microelectrodes held at alternating applied potentials on one wall of a flow channel. The downstream microelectrode of each pair detects species generated at the upstream microelectrode. Concentration profiles in the channel, amperometric response, and signal-to-noise ratios for the detector electrodes are calculated. The simple backward implicit finite difference (BIFD) simulation approach is applicable for a wide range of channel conditions. The upper number of electrode pairs treatable is limited only by computational time. The agreement of the simulation with previous results for a single pair of electrodes under comparable conditions is very good. Substantial improvements in signal-to-noise ratio are predicted for the multi-electrode interdigitated electrode array relative to a single generator-detector pair of equal overall area. Electrode dimensions are discussed for optimum signal/noise ratio. Relative enhancement increases significantly with the number of generator-detector pairs.     

A new dynamic electrochemical transduction mechanism for interdigitated array microelectrodes

A dynamic electrochemical transduction mechanism for interdigitated array microelectrodes using an electrical charge pumping method is presented in this paper. In this dynamic transduction mechanism, a charged external capacitor is used as the charge supplier for the electrochemical reaction of the reversible redox species at the interdigitated array electrodes. The charges stored in the capacitor are consumed as the electrochemical reaction current, which causes the capacitor potential decay. The theoretical analysis has shown that the species concentration has a decisive effect on the capacitor potential decay, and therefore the characteristics of the capacitor potential decay are recorded and analyzed to evaluate the concentration of redox species. The new transduction mechanism has the advantages of achieving high sensitivity with small sensor area and simplifying the measurement instrumentation. As a demonstration device, interdigitated array microelectrodes (approximately 0.2 mm(2) electrode surface area) have been fabricated and successfully characterized using p-aminophenol as the redox species under this dynamic mechanism. The detection limit of p-aminophenol was calculated to be approximately 4 x 10(-7) M for the sensor with the new dynamic transduction mechanism.     

Dielectrophoretic cell trapping for improved surface plasmon resonance imaging sensing

The performance of conventional surface plasmon resonance (SPR) biosensors can be limited by the diffusion of the target analyte to the sensor surface. This work presents an SPR biosensor that incorporates an active mass‐transport mechanism based on dielectrophoresis and electroosmotic flow to enhance analyte transport to the sensor surface and reduce the time required for detection. Both these phenomena rely on the generation of AC electric fields that can be tailored by shaping the electrodes that also serve as the SPR sensing areas. Numerical simulations of electric field distribution and microparticle trajectories were performed to choose an optimal electrode design. The proposed design improves on previous work combining SPR with DEP by using face‐to‐face electrodes, rather than a planar interdigitated design. Two different top‐bottom electrode designs were experimentally tested to concentrate firstly latex beads and secondly biological cells onto the SPR sensing area. SPR measurements were then performed by varying the target concentrations. The electrohydrodynamic flow enabled efficient concentration of small objects (3 μm beads, yeasts) onto the SPR sensing area, which resulted in an order of magnitude increased SPR response. Negative dielectrophoresis was also used to concentrate HEK293 cells onto the metal electrodes surrounded by insulating areas, where the SPR response was improved by one order of magnitude.     

Chiral analysis of neurotransmitters using cyclodextrin-modified capillary electrophoresis equipped with microfabricated interdigitated electrodes

We present cyclodextrin-modified capillary electrophoresis equipped with a microfabricated chip consisting of an array of eight interdigitated microband platinum electrodes (IDs) for simultaneous analysis of three chiral models: epinephrine, norepinephrine and isoproterenol. The IDE chip, positioned very close to the capillary outlet, served as an amplification/detection system. Emerging neurotransmitters at the IDE surface were oxidized at +1.1 V by seven electrodes of the array and then detected by the remaining electrode, poised at +0.0 V. There was an amplification effect on the detecting electrode owing to the recycle between the reduced and oxidized forms of the optical isomers at the electrode surface. The detecting "amplification" current response was governed by the applied potential, the detecting electrode position, the number of adjacent electrodes used for recycling and the distance between the oxidative and reductive electrodes. The six chiral forms of the three neurotransmitters were resolved using 25 mM heptakis(2,6,di-o-methyl)-beta-cyclodextrin with a detection limit of approximately 5 microM. The scheme detected a reduced compound at a reducing potential instead of conventional oxidation detection to alleviate electrode fouling and electroactive interferences. The concurrent oxidation/reduction detection of compounds also facilitated and ascertained peak identification as interfering compounds were unlikely to have the same oxidative/reductive characteristics and mobilities as the analytes of interrogation.     

Biophysical measurement of red blood cells by laboratory on print circuit board chip

Microfluidic impedance pulse sensor has emerged as an easily handled and low‐cost platform in the electrical analysis of biological cells. In the conventional method, impedance sensor demanded expensive patterning metal electrodes on the substrate, which are directly in touch with electrolytes in order to measure the microfluidic channel impedance change. In this article, a cost‐effective microfluidic impedance sensor built upon a dielectric film coated printed circuit board is introduced. Impedance electrodes are protected by a dielectric film layer from electrochemical erosion between electrodes and electrolyte. Human red blood cells from adult and neonatal were utilized to demonstrate the feasibility of the proposed device in the electroanalysis of biological cells.     

Detection of chlorinated quinones using interdigitated electrodes coupled with capillary electrophoresis

An array of eight interdigitated microband gold electrodes (IDEs) has been developed together with electrophoretic separation for analysis of chlorinated hydroquinones (ClHQs) and benzoquinones (ClBQs). The IDE chip positioned very close to the separation capillary outlet served as an amplification/detection system without the requirement for frequent "capillary-electrode" alignment. ClHQs, electrophoretically migrating to the IDE surface, were oxidized at +1.1 V by seven electrodes of the array and then detected by the remaining electrode, poised at -0.1 V. Conversely, ClBQs were detected at +1.1 V by the detecting electrode after having been reduced at the 7 adjacent electrodes poised at -0.1 V. There was an amplification effect on both the detecting electrode as well as the adjacent electrodes because of the recycle between ClHQs and ClBQs. The detecting "amplification" current response was dependent on the potentials applied, the position of the detecting electrode on the array, the number of adjacent electrodes being used for recycling and the distance between the oxidative and reductive electrodes. Micellar electrokinetic chromatography (MEKC) separation of the analytes was achieved using 30 mM sodium dodecyl sulfate (SDS) with a detection limit in the range of 2-20 micro M. In addition to a facile "capillary-electrode" alignment, the important aspect described here was the capability of detecting through recycling a reduced compound (in the case of ClHQs) at a negative potential to circumvent fouling and electroactive interferences. An appealing feature was also the concurrent oxidation/reduction detection for each compound to ascertain peak assignment, as interfering compounds are less likely to exhibit the same oxidative/reductive characteristics and electrophoretic mobilities as the target analytes.     

On the Integration of Dielectrometry into Electrochemical Impedance Spectroscopy to Obtain Characteristic Properties of a Dielectric Thin Film

We demonstrate a novel impedimetric approach providing unprecedented insight into characteristic properties of dielectric thin films covering electrode surfaces. The concept is based on the joint interpretation of electrochemical impedance spectroscopy (EIS) together with dielectrometry (DEM) whose informative value is mutually interconnected. The advantage lies in the synergistic compensation of individual shortcomings adversely affecting conventional impedimetric analysis strategies relying exclusively on either DEM or the traditional EIS approach, which in turn allows a reliable determination of thickness and permittivity values. The versatility of the method proposed is showcased by an in-situ growth-monitoring of a nanoporous, crystalline thin film (HKUST-1) on an interdigitated electrode geometry.     

Probing Biomolecular Interactions at Conductive and Semiconductive Surfaces by Impedance Spectroscopy: Routes to Impedimetric Immunosensors,DNA‐Sensors,and Enzyme Biosensors

Impedance spectroscopy is a rapidly developing electrochemical technique for the characterization of biomaterial‐functionalized electrodes and biocatalytic transformations at electrode surfaces, and specifically for the transduction of biosensing events at electrodes or field‐effect transistor devices. The immobilization of biomaterials, e.g., enzymes, antigens/antibodies or DNA on electrodes or semiconductor surfaces alters the capacitance and interfacial electron transfer resistance of the conductive or semiconductive electrodes. Impedance spectroscopy allows analysis of interfacial changes originating from biorecognition events at electrode surfaces. Kinetics and mechanisms of electron transfer processes corresponding to biocatalytic reactions occurring at modified electrodes can be also derived from Faradaic impedance spectroscopy. Different immunosensors that use impedance measurements for the transduction of antigen‐antibody complex formation on electronic transducers were developed. Similarly, DNA biosensors using impedance measurements as readout signals were developed. Amplified detection of the analyte DNA using Faradaic impedance spectroscopy was accomplished by the coupling of functionalized liposomes or by the association of biocatalytic conjugates to the sensing interface providing biocatalyzed precipitation of an insoluble product on the electrodes. The amplified detections of viral DNA and single‐base mismatches in DNA were accomplished by similar methods. The changes of interfacial features of gate surfaces of field‐effect transistors (FET) upon the formation of antigen‐antibody complexes or assembly of protein arrays were probed by impedance measurements and specifically by transconductance measurements. Impedance spectroscopy was also applied to characterize enzyme‐based biosensors. The reconstitution of apo‐enzymes on cofactor‐functionalized electrodes and the formation of cofactor‐enzyme affinity complexes on electrodes were probed by Faradaic impedance spectroscopy. Also biocatalyzed reactions occurring on electrode surfaces were analyzed by impedance spectroscopy. The theoretical background of the different methods and their practical applications in analytical procedures were outlined in this article.