Extraction and spectrophotometric determination of titanium(IV) with malachite green and p-chloromandelic acid, with application to mild steels

A very sensitive, selective and simple method for extraction and spectrophotometric determination of titanium(IV) with an alpha-hydroxy acid has been developed. p-Chloromandelic acid reacts with titanium in weakly acidic aqueous solution at room temperature to form a complex anion extractable into chlorobenzene with Malachite Green as counter-ion. Titanium is determined indirectly by measuring the absorbance of Malachite Green in the extract at 630 nm. The calibration graph is linear for titanium(IV) over the range 0.25-7.5muM (0.05-1.44 mug); the apparent molar absorptivity is 1.31 x 10(5) l.mole(-1).cm(-1). The method has been successfully applied to the determination of titanium in mild steels.     

Extraction-spectrophotometric determination of germanium(IV) with mandelic acid and malachite green

A method has been developed for determination of germanium, based on complexation with mandelic acid and extraction of the ion-associate formed with Malachite Green (MG) into chlorobenzene. A weakly acidic aqueous solution (pH 2.5-3.5) at room temperature is used and indirect determination is achieved by measuring the absorbance of MG in the extract, at 628 mn. The calibration graph is linear over the range (0.17-8.63) x 10(-6) (0.05-2.50 mug of germanium); the apparent molar absorptivity is 1.33 x 10(5) 1.mole(-1).cm(-1). The interferences from Fe, Ti, Sn(IV), Mo, and SB(III) can be eliminated by addition of trans-1,2-diaminocyclohexanetetra-acetic acid and sodium diethyldithiocarbamate.     

Manual and fia methods for the determination of cadmium with malachite green and iodide

A sensitive and rapid spectrophotometric method for the determination of cadmium is described, based on the formation of a blue complex at pH 4 between the anionic iodide complex of cadmium(II) and Malachite Green; the colour is stabilized with poly(vinyl alcohol). The calibration graph for measurement at 685 nm is linear over the range 1-50 mug of cadmium per 25 ml of final solution, with a relative standard deviation of +/-1.7% for 1 mug/ml cadmium. The molar absorptivity is 6.1 x 10(4) 1.mole(-1).cm(-1). The method can be successfully adapted for FIA, the peak height being proportional to the cadmium concentration over the range 0.1-3 mug/ml; a two-channel manifold is used and an improvement in selectivity is obtained. The use of a gradient tube is demonstrated to give a good calibration for Cd(II) over the range 2 x 10(-2) -2 x 10(-6)M.     

Solvent extraction-spectrophotometric determination of phosphate with molybdate and malachite green in river water and sea-water

Molybdophosphate, formed between orthophosphate and molybdate in sulphuric acid solution, is extracted into a mixture of toluene and 4-methylpentan-2-one (1:3 v v ) with Malachite Green as counter-ion. A single extraction with equal phase volumes gives an apparent molar absorptivity for phosphate of 2.3 x 10(5) l.mole(-1).cm(-1) at 630 nm; the absorbance of the reagent blank is 0.03. With an organic to aqueous phase-volume ratio of 1:10, the molar absorptivity is 2.5 x 10(5) l.mole(-1).cm(-1) and the absorbance of the reagent blank 0.08. By the proposed method, ng ml levels of phosphorus can be determined, and the detection limit is about 0.1 ng ml . The standard deviation and relative standard deviation for the determination of phosphorus in tap water (4.3 ng ml ) are 0.05 ng ml and 1.1%, respectively. The method can also be applied to the determination of phosphorus in river water and sea-water.     

Screening and confirmation of triphenylmethane dyes and their leuco metabolites in trout muscle using HPLC-vis and ESP-LC-MS.

An extraction and clean-up protocol for the determination of Malachite Green and Crystal Violet and the corresponding leuco compounds in trout muscle has been developed. Final determination is by HPLC with visible (screening) or ESP-MS (confirmation) detection. In both cases lead(IV) oxide was used on-line to oxidise the leuco compounds back to the parent after chromatographic separation and prior to detection. The procedure was validated down to 2 micrograms kg-1. Intra- and inter-batch precision was measured at 3 levels for all compounds. Recoveries were in the range 66-116% with RSD of 1-17% for determination by HPLC with visible detection. For LC-MS determination, recoveries were in the range 61-94% with RSD of 4-15%. Limited surveillance data indicated that Malachite Green usage was more effectively monitored by including the leuco compound as well as the parent (9 positives for the leuco compound as opposed to 1 for Malachite Green out of 31 samples analysed).     

Extractive spectrophotometric determination of uranium with Malachite Green

A sensitive spectrophotometric method based on the extraction of a uranium-benzoate-Malachite Green complex by chlorobenzene is described. The absorption maximum is at 635 nm and the molar absorptivity is 8.3 x 10(4) 1 mole(-1), cm(-1). A preliminary separation of uranium by extraction with methyl isobutyl ketone from acid-deficient aluminium nitrate solution is used to avoid interferences. An aliquot of the extract is then diluted with chlorobenzene and shaken with benzoate buffer containing Malachite Green (MG). The method has been applied for the determination of uranium in a synthetic leach solution. The complex extracted is probably [MG(2)(C(6)H(5)COO)(3)][MG(+)].     

A highly sensitive spectrophotometric method for determination of micro amounts of arsenic

A highly sensitive spectrophotometric method for determination of arsenic, based on the formation of an ion-association complex between arsenoantimonomolybdenum blue and Malachite Green, has been developed. The ion-association complex is soluble in the presence of Triton X-305, so arsenic can be determined directly in aqueous solution. The apparent molar absorptivity for arsenic is 1.13 x 10(5) l.mole(-1).cm(-1) at 640 nm. Beer's law is obeyed for 0-5 mug of arsenic. The lower limit of determination (absorbance = 0.01) is 4 ng ml in the final solution.     

A novel and highly sensitive catalytic method with oscillopolarographic detection for the determination of ultratrace amounts of iridium

Iridium(IV) has a strong catalytic effect on the slow redox reaction between Malachite Green and periodate ion in pH 4.2 acetate buffer solution at 100 degrees , and Malachite Green exhibits a sensitive single-sweep oscillopolarographic wave at -0.65 V vs. SCE. This provides the basis for a novel and highly sensitive and selective catalytic method with oscillopolarographic detection for iridium. The effect of pH, potassium periodate and Malachite Green concentrations, reaction temperature and reaction time and other variables are investigated. The detection limit is 8 ng/l. with a fixed-reaction time of 10 min. A linear calibration graph from 24 to 1600 ng/l. is obtained. Possible interferences by co-existing ions are examined.     

Ultrasonic enhancement of leaching and in situ derivatization of haloacetic acids in vegetable foods prior to gas chromatography-electron capture detection

With a new oxidant for post-column chemical derivation, a novel approach was developed for the determination of Malachite Green (MG) and Leucomalachite Green (LMG) in fish by high-performance liquid chromatography (HPLC). A C(8) column was used for separation, and elution was performed with a pH 2.5 phosphate buffer (0.02molL(-1)) containing 40% acetonitrile. When the eluate was combined with 3.0x10(-4)molL(-1) iodine solution, LMG was converted to MG and detected at 618nm after post-column derivatization. The recoveries of MG and LMG were ranged from 67.3% to 73.9% and 84.7% to 92.1%, respectively, which were obtained by measuring the amount of MG and LMG in the samples with solvent calibration curve. The decision limit (CCalpha) and the detection capability (CCbeta) obtained for MG and LMG were in the range of 0.10-0.17 and 0.13-0.23mugkg(-1) in grass carp, shrimp and shellfish. This method appeared suitable for the control of MG and LMG residues in aquatic products.     

Rapid flow injection spectrophotometric determination of monofluorophosphates in toothpastes after on-line hydrolysis by alkaline phosphatase immobilized on a cellulose nitrate membrane

A new, rapid flow injection (FI) method is reported for the spectrophotometric determination of monofluorophosphate (MFP) ions in toothpastes. MFP ions are hydrolyzed on-line by alkalinephosphatase (APase) immobilized on a cellulose nitrate membrane, prior to injection in the FI system. The yielded orthophosphate ions are determined spectrophotometrically (lambda(max) = 690 nm) using the molybdenum blue approach. The chemical and FI variables that affected the enzymatic reaction were studied and optimized. A study of interferences was also carried out. The proposed method is very precise (s(r) = 0.7% at 1.0 x 10(-4) mol l(-1) MFP, n = 12), fast (sampling rate of 72 h(-1)) and allows the determination of MFP ions in the range of 4.0 x 10(-5) to 6.0 x 10(-4) mol l(-1) with a satisfactory 3sigma detection limit of 4.0 x 10(-6) mol l(-1). The application of the proposed FI method to toothpaste samples yielded accurate results (e(r) < 2.0%) compared with a potentiometric reference procedure.     

New phase separator for extraction-spectrophotometric determination of anionic surfactants with Malachite Green by flow injection analysis

A simple flow injection spectrophotometric method for the determination of anionic surfactants in river water was studied. A three-channel flow system was assembled. The distilled water as a carrier and 5x10(-5) mol l(-1) Malachite Green (MG) dissolved in 0.1 mol l(-1) CH(3)COONa-CH(3)COOH buffer solution (pH 5) were delivered at 1.94 ml min(-1). The mixed solvent (toluene+methylisobutyl ketone (MIBK)=1+1) was pumped at 0.78 ml min(-1). Other conditions were the extraction coil 0.5 mm i.d.x3 m, the reaction temperature 20 degrees C and the sample size 200 mul. The calibration graph was linear in the range 0.1-0.4 ppm at 626 nm. The detection limit (S/N=3) was 18 ppb and a sample frequency of 20 h(-1) was attained. The relative standard deviation (n=7) for 0.4 ppm standard sodium dodecylsulfate (SDS) solutions was 1.1%. And also, new phase separator with a convenient connector was designed. This Fl method was applied to the determination of anionic surfactants in river water.     

Microscopic location of photosensitive Malachite Green surfactant in mixed micelle and its photoinduced enhancement of solubilizing power

A Malachite Green derivative carrying a long alkyl chain affords photogenerated amphiphilicity by UV irradiation. The behavior of the photoresponsive Malachite Green surfactant was studied in mixed micelle solutions containing cetyltrimethylammonium chloride. We found that the Malachite Green surfactant increases the solubility of oily substance by UV irradiation. The role of the Malachite Green surfactant has been investigated by dynamic light scattering and spectroscopic analysis. The Malachite Green surfactant causes an increase in the micelle size, and its hydrophilic head group lies at the micellar interface. The mechanism of the photoinduced uptake of oily substances is discussed at the viewpoint of the microscopic location of the Malachite Green surfactant in the micelle.     

Differential pulse polarographic determination of trace amounts of vanadium and molybdenum in various standard alloys and environmental samples after preconcentration of their morpholine-4-carbodithioates on microcrystalline naphthalene or morpholine-4-dithiocarbamate cetyltrimethyl-ammonium bromide-naphthalene adsorbent

A highly selective, sensitive, and fairly rapid and economical differential pulse polarographic (DPP) method has been reported for the determination of trace amounts of vanadium and molybdenum in standard alloys and various environmental samples. The morpholine-4-carbodithioates of these metals were retained (>99% recovery) quantitatively on microcrystalline naphthalene in the pH range 4.5-6.9 for vanadium and 1.5-4.5 for molybdenum. These metals were determined by DPP after desorption with 10 ml of 1 M HCl. Vanadium and molybdenum may also be preconcentrated by passing their aqueous solutions under similar conditions on morpholine-4-dithiocarbamate CTMAB-naphthalene adsorbent packed in a column at a flow rate of 1-5 ml min(-1) and determined similarly. The detection limits are 0.20 ppm for vanadium and 0.04 ppm for molybdenum at minimum instrumental settings (signal to noise ratio=2). The linearity is maintained in the following concentration ranges, vanadium 0.50-10.0 and molybdenum 0.10-9.0 ppm, with a correlation factor of 0.9996 (confidence interval of 95%, slopes 0.0196 and 0.01497 muA mug(-1), intercepts 3.65x10(-3) and -1.92x10(-3) respectively) and relative standard deviation of 1.1% in the microcrystalline method, while in the column method, the linearity is maintained in the concentration ranges, 0.50-6.5 for vanadium and 0.10-5.5 ppm for molybdenum with correlation factor of 0.9994 (with confidence interval of 95%, slopes 0.0194, 0.015 muA mug(-1), intercepts 3.60x10(-3) and -1.90x10(-3) respectively) and relative standard deviation of 1.4%. Various parameters such as the effect of pH, reagent, naphthalene and CTMAB concentrations, volume of aqueous phase and interference of a large number of metal ions on the estimation of vanadium and molybdenum have been studied in detail to optimize the conditions for their voltammetric determination at trace level in various standard alloys and environmental samples.     

Differential pulse polarographic determination of trace selenium(IV) and molybdenum(VI) using the catalytic hydrogen wave

In the presence of selenium(IV) and molybdenum(VI) a new polarographic peak appears which corresponds to a hydrogen catalytic wave. By differential pulse polarography a single, sharp peak at about -1.1 V is obtained, allowing trace determination of selenium(IV) and molybdenum(VI) in the range 1x10(-6)-5.0x10(-9) M with a linear calibration and a detection limit of 1.5x10(-9) M. The optimum conditions are found to be 0.1 M KNO(3) and a pH of about 3.2 (Britton-Robinson buffer). There is no serious interference from some ions when present at 1.0-40 times that of molybdenum. At higher amounts of interfering ions the interference is eliminated by the addition of EDTA.     

Extractive-spectrophotometric determination of molybdenum as an ion-association complex with thiocyanate and adogen

A selective and sensitive method is described for the determination of trace amounts of molybdenum, based on its reaction with thiocyanate and its extraction (into toluene) as an ion-association complex formed with adogen (methyltrioctylammonium chloride). The molar absorptivity is 2.13 x 10(4) l.mole(-1).cm(-1) at lambda(max) 467 nm. The method has been applied to molybdenum determination in steels.     

Spectrophotometric determination of rhenium with dithio-oxamide in strongly alkaline medium

The interaction between rhenium(VII) and dithio-oxamide in strongly alkaline medium in presence of tin(II) chloride as reluctant has been studied. A purple complex is obtained, with lambda(max) 526 nm and (max) = 4.0 x 10(3) l.mole(-1).cm(-1). The reaction has been applied to the determination of rhenium in tungsten-rhenium alloy after its anodic electrochemical dissolution in alkaline medium. A 1000-fold excess of molybdenum or tungsten does not interfere. A modification of the proposed method can be used as a spot-test for rapid control of rhenium content in industrial solutions.     

Spectrophotometric estimation of molybdenum with disodiom cis-1,2-dicyanoetfaylene-1,2-dithiolate

A rapid spectrophotometnc method is described for estimation of molybdenum by use of the molybdenum-dicyanoethytene dithiolate complex. The bright green complex has its absorption maximum at 665 nm and in 50% aqueous acetonitrilc is stable for several days at 3M hydrochloric add concentration, The estimation is more sélective if longer wavelengths and high acidity are used. Beer's law is obeyed over the range 1-16 ppm molybdenum, optimum range 4-16 ppm. The overall formation constant Of the complex with metal to ligand ratio of 1:4 is 5 +/- 2 x 10(18). The molar absorptivity is 5.05 x 10(3) l.mole(-1).cm(-1).     

Solvent extraction and photometric determination of molybdenum (VI) with 2-aminobenzenethiol

A new extractive photometric method is described for estimation of molybdenum with 2-aminobenzenethiol. The green complex in chloroform has its absorbance maximum at 700 nm and is stable for 2 hr when extracted from a solution of optimum pH range 1.4-2.8. The extraction is quantitative. The sensitivity is 0.0075 microg cm (2). Beer's law is obeyed over the range 0.25-10 ppm with optimum range 0.5-4.5 ppm. The molar absorptivity is 7.08 x 10(4) 1.mole(-1). cm(-1). The overall stability constant is 2.0 x 10(8) at 25 +/- 0.1 degrees.     

Extraction-spectrophotometric determination of boron and antimony in carbon and low-alloy steels with mandelic acid and malachite green

A very simple and sensitive extraction method using mandelic acid and Malachite Green has been applied to the determination of boron and antimony in steels (carbon and low-alloy). When chlorobenzene is used as the solvent, boron and antimony are simultaneously extracted as ion-pairs of their mandelates with Malachite Green from weak acidic media, but only the boron compound is extracted in the presence of tartrate. Antimony is determined from the difference in absorbance of the extracts. In the case of benzene, boron alone was extracted and determined. Large amounts of iron(II) and other metal cations do not interfere, so the steel samples are dissolved in dilute sulphuric acid. Very low boron (0.0009-0.0091%) and antimony (0.002-0.02%) contents in steel are easily determined without any pretreatment.     

Liquid-liquid extraction of molybdenum thiocyanate with hexamethyl phosphortriamide and direct spectrophotometric determination in the organic phase

A sensitive and selective method for estimation of trace molybdenum with fairly common reagents has been developed. The Mo-thiocyanate complex is extracted with hexamethyl phosphortriamide and chloroform from 0.75-1.5M hydrochloric acid. The molar absorptivity is 1.76 x 10(4) 1.mole(-1).cm(-1). The system obeys Beer's law at 460nm over the molybdenum concentration range 0.75-5ppm. The method is simple, rapid, and requires no additional reducing agent. It is generally free from interference by most of the metals commonly associated with molybdenum, including rhenium. Molybdenum in alloy steel has been successfully determined.