Specific properties of in situ ruthenium‐catalyzed polyamide 12/polydimethylsiloxane compatibilized blend

The main objective of this work focused on the chemical modification of polyamide 12 (PA12) properties through the reaction with a hydride‐terminated polydimethylsiloxane (PDMS‐SiH). The investigated PA12/PDMS‐SiH blend was compatibilized by ruthenium derivative catalyzed hydrosilylation reaction in molten state. This original route enhanced interfacial adhesion and avoid PDMS‐SiH leaching phenomenon between the two immiscible phases. More specifically, the size of PDMS‐SiH domains in the blend decreased from around 4 μm to 800 nm and from 30 to 1 μm after compatibilization with 10 and 20 wt % PDMS‐SiH, respectively. For the best compatibilized PA12/PDMS‐SiH blend, the introduction of PDMS lowered the surface free energy and the PA12‐based blend turned from hydrophilic to hydrophobic behavior, as evidenced by the water contact angle measurements. Gas permeability and CO₂/H₂ and CO₂/He gas selectivity were also improved with the increase in PDMS content. Besides, the mechanical properties were enhanced with 13% increase in Young's modulus after in situ compatibilization with 15 wt % PDMS‐SiH. Thermal stability was also improved after compatibilization as the initial degradation temperature of reactive blends obviously increased compared with nonreactive ones. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 978–988     

Effects of molecular weight of nitrocellulose on structure and properties of polyurethane/nitrocellulose IPNs

Semi‐interpenetrating polymer network (semi‐IPN) coatings were prepared by using castor oil‐based polyurethane (PU) and nitrocellulose (NC) with various viscosity‐average molecular weights (M_η) from 6 × 10⁴ to 42 × 10⁴, and coated on a regenerated cellulose (RC) film to obtain water‐resistant film. The PU/NC coatings and coated films, which were cured at 80°C for 5 min and 2 min, respectively, were investigated by infrared (IR) and ultraviolet (UV) spectroscopy, X‐ray diffraction, swelling test, strength test, dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The results show that the crosslink densities of the PU/NC semi‐IPNs were smaller than that of pure PU, and decreased with the decrease of M_η of nitrocellulose (NC M_η), indicating NC molecules cohered intimately with PU, and hindered the PU network formation. The physical and mechanical properties of the films coated with PU/NC coatings were significantly improved. With the increase of NC M_η, the strength and thermal stability of the coated films increased, but the pliability, water resistivity, and optical transmission decreased slowly. The PU/NC coating with low NC M_η more readily penetrated into the RC film, and reacted with cellulose, resulting in a strong interfacial bonding and dense surface caused by intimate blend of PU/NC in the coated films. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1623–1631, 1999     

Novel method for the preparation of poly(urethane–imide)s and their properties

A polymer blend consisting of polyimide (PI) and polyurethane (PU) was prepared by means of a novel approach. PU prepolymer was prepared by the reaction of polyester polyol and 2,4-tolylenediisocyanate (2,4-TDI) and then end-capped with phenol. Poly(amide acid) was prepared from pyromellitic dianhydride (PMDA) and oxydianiline (ODA). A series of oligo(amide acid)s were also prepared by controlling the molar ratio of PMDA and ODA. The PU prepolymer and poly(amide acid) or oligo(amide acid) solution were blended at room temperature in various weight ratios. The cast films were obtained from the blend solution and treated at various temperatures. With the increase of polyurethane component, the films changed from plastic to brittle and then to elastic. The poly(urethane–imide) elastomers showed excellent mechanical properties and moderate thermal stability. The elongation of films with elasticity was more than 300%. The elongation set after the breaking of films was small. From the dynamic mechanical analysis, all the samples showed a glass transition temperature (T_g) at ca. −15°C, corresponding to T_g of the urethane component, suggesting that phase separation occurred between the two polymer components, irrespective of polyimide content. TGA and DSC studies indicated that the thermal degradation of poly(urethane–imide) was in the temperature range 250–270°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3745–3753, 1997     

Effect of silane coupling agent on mechanical interfacial properties of glass fiber‐reinforced unsaturated polyester composites

A silane coupling agent, γ‐methacryloxypropyltrimethoxysilane, for the surface modification of glass fibers was varied between 0.1 and 0.8 wt %. To understand the role of interfacial adhesion of glass fiber/unsaturated polyester composites, contact angles of the silane‐treated glass fibers were measured by the wicking method on the basis of the modified Washburn equation with deionized water, diiodomethane, and ethylene glycol as testing liquids. As a result, silane‐treated glass fibers led to increased surface free energy, mainly because of their increased specific or polar component. The mechanical interfacial behaviors based on the interlaminar shear strength (ILSS) of the composites determined by short‐beam tests and the critical stress‐intensity factor (K_IC) were also improved in the case of silane‐treated composites. The surface free energy and the mechanical interfacial properties especially showed the maximum value in the presence of 0.4 wt % silane coupling agent. It revealed that the increase of a specific component of the surface free energy or hydrogen bonding between the glass fibers and the coupling agents plays an important role in improving the degree of adhesion at interfaces in a composite system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 55–62, 2003     

Preparation of high‐temperature polyurethane by alloying with reactive polyamide

A series of novel poly(urethane amide) films were prepared by the reaction of a polyurethane (PU) prepolymer and a soluble polyamide (PA) containing aliphatic hydroxyl groups in the backbone. The PU prepolymer was prepared by the reaction of polyester polyol and 2,4‐tolylenediisocyanate and then was end‐capped with phenol. Soluble PA was prepared by the reaction of 1‐(m‐aminophenyl)‐2‐(p‐aminophenyl)ethanol and terephthaloyl chloride. The PU prepolymer and PA were blended, and the clear, transparent solutions were cast on glass substrates; this was followed by thermal treatments at various temperatures to produce reactions between the isocyanate group of the PU prepolymer and the hydroxyl group of PA. The opaque poly(urethane amide) films showed various properties, from those of plastics to those of elastomers, depending on the ratio of the PU and PA components. Dynamic mechanical analysis showed two glass‐transition temperatures (T_g's), a lower T_g due to the PU component and a higher T_g due to the PA component, suggesting that the two polymer components were phase‐separated. The rubbery plateau region of the storage modulus for the elastic films was maintained up to about 250 °C, which is considerably higher than for conventional PUs. Tensile measurements of the elastic films of 90/10 PU/PA showed that the elongation was as high as 347%. This indicated that the alloying of PU with PA containing aliphatic hydroxyl groups in the backbone improved the high‐temperature properties of PU and, therefore, enhanced the use temperature of PU. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3497–3503, 2002     

Amine‐cured epoxy/clay nanocomposites. II. The effect of the nanoclay aspect ratio

The thermophysical and mechanical properties of a nanocomposite material composed of amine‐cured diglycidyl ether of bisphenol A (DGEBA) reinforced with organomontmorillonite clay are reported. The storage modulus at 100 °C, which was above the glass‐transition temperature (T_g), increased approximately 350% with the addition of 10 wt % (6.0 vol %) of clay. Below the T_g, the storage modulus at 30 °C increased 50% relative to the value of unfilled epoxy. It was determined that the T_g linearly increased as a function of clay volume percent. The tensile modulus of epoxy at room temperature increased approximately 50% with the addition of 10 wt % of clay. The reinforcing effect of the organoclay nanoplatelets is discussed with respect to the Tandon–Weng and Halpin–Tsai models. A pseudoinclusion model is proposed to describe the behavior of randomly oriented, uniformly dispersed platelets in nanocomposite materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4391–4400, 2004     

Influence of carboxyl‐terminated (butadiene‐co‐acrylonitrile) loading on the mechanical and thermal properties of cured epoxy blends

A mixture of epoxy with liquid nitrile rubber, carboxyl‐terminated (butadiene‐co‐acrylonitrile) (CTBN) was cured under various temperatures. The cured resin was a two‐phase system, where spherical rubber domains were dispersed in the matrix of epoxy. The morphology development during cure was investigated by scanning electron microscope (SEM). There was slight reduction in the glass transition temperature of the epoxy matrix (T_g) on the addition of CTBN. It was observed that, for a particular CTBN content, T_g was found to be unaffected by the cure temperature. Bimodal distribution of particles was noted by SEM analysis. The increase in the size of rubber domains with CTBN content is due probably to the coalescence of the rubber particles. The mechanical properties of the cured resin were thoroughly investigated. Although there was a slight reduction in tensile strength and young's modulus, appreciable improvements in impact strength, fracture energy, and fracture toughness were observed. Addition of nitrile rubber above 20 parts per hundred parts of resin (phr) made the epoxy network more flexible. The volume fraction of dispersed rubbery phase and interfacial area were increased with the addition of more CTBN. A two‐phase morphology was further established by dynamic mechanical analysis (DMA). © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2531–2544, 2004     

In situ compatibilization of PET/PS blends through carbamate‐functionalized reactive copolymers

To investigate the effect of reactive compatibilization in the immiscible poly(ethylene terephthalate) (PET)/polystyrene (PS) blend, poly(styrene‐co‐methacryloyl carbamate) (PSM) was synthesized as a reactive compatibilizer. The interfacial reaction of the carbamate group in PSM with OH/COOH in PET was confirmed by atomic force microscopy. The interfacial roughness developed rapidly with an increase in the methacryloyl carbamate (MAC) content and then leveled off above the optimum content (3.8 wt %). These results were well‐reflected in the interfacial adhesion, morphology, and mechanical properties of the PET/PS blends, showing a maximum value at the optimum MAC content. The existence of a maximum value is believed to stem from a reciprocal relationship between the sufficient formation of in situ copolymer and the fast diffusion rate of reactive polymers at the interface. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1396–1404, 2000     

Interfacial adhesion mechanisms in incompatible semicrystalline polymer systems

The mechanism of adhesion at semicrystalline polymer interfaces between isotactic polypropylene (iPP) and linear low‐density polyethylene (PE) was studied with transmission electron microscopy (TEM) and an asymmetric‐double‐cantilever‐beam test. From the TEM images, both the interfacial width and the lamellar thickness of the polymers were extracted. During annealing, the interfacial width increased with the annealing temperature, and this indicated the accumulation of amorphous polymers at the interface. The interfacial strength, determined from the critical fracture energy (G_c), also increased with the annealing temperature and reached a maximum above the melting temperatures of iPP and PE, whereas the smallest G_c value was obtained below the melting temperatures of the two materials. A mechanism of interfacial strengthening was proposed accounting for the competition between the interdiffusion of PE and crystallization of iPP. As the annealing temperature increased, the rates of PE diffusion and iPP crystallization increased. Although the crystallization of iPP hindered the interdiffusion of PE, both the interfacial width and the fracture energy increased with the temperature, and this indicated that PE interdiffusion dominated iPP crystallization. Below the critical temperature, the fracture surfaces of both iPP and PE were smooth, and chain pullout dominated the fracture mechanism. Above the critical temperature, iPP crystallization still hindered the interdiffusion, and crazes could be seen on the iPP side. Above the melting temperatures of the two materials, ruptured surfaces could also be seen on the PE side, and crazing was the fracture mechanism. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2667–2679, 2004     

Phase behavior and crystallization of a poly(ethylene oxide)/cellulose acetate butyrate blend

The phase behavior of a partially miscible blend of poly(ethylene oxide) (PEO) and cellulose acetate butyrate (CAB) and the crystalline microstructure of PEO in the blend were studied with differential scanning calorimetry (DSC), optical microscopy, and synchrotron small‐angle X‐ray scattering (SAXS) methods. PEO/CAB showed a lower critical solution temperature (LCST) of 168 °C at the critical composition of PEO of 60 wt %. All blend compositions showed a single glass‐transition temperature (T_g) when they were prepared at temperatures lower than the LCST. However, with increasing CAB content, T_g of the blend changed abruptly at 70 wt % CAB; that is, a cusp existed. Below 70 wt % CAB, the change in T_g with blend composition was predicted by the Brau–Kovacs equation, whereas this change was predicted by the Fox equation at higher CAB contents. A gradual but small depression of the melting point of PEO in the blend with an increasing amount of CAB suggested that the PEO/CAB blends exhibited a weak intermolecular interaction. From DSC and SAXS experiments, it was found that amorphous CAB was incorporated into the interlamellar region of PEO for blends with less than 20 wt % CAB, whereas it was segregated to exist in the interfibrillar region in PEO for other blends with larger amounts of CAB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1673–1681, 2002     

Thermodynamic analysis of the phase separation during the polymerization of a thermoset system into a thermoplastic matrix. II. Prediction of the phase composition and the volume fraction of the dispersed phase

A thermodynamic simulation of the phase‐separation process of an off‐critical blend, based on a thermoplastic matrix with a reactive epoxy system undergoing polycondensation at a constant temperature, was performed. The model considered the composition dependence of the interaction parameter, χ(T,Φ₂) (where T is the temperature and Φ₂ is the volume fraction of polystyrene), along with the polydispersity of both polymers. For every level of conversion, the simulation provided the amount, composition, stoichiometric ratio, and conversion of each phase present. The accuracy of the model was proved by the good agreement between the experimental and predicted glass‐transition temperatures and heat capacity changes at the glass‐transition temperatures for both phases. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1361–1368, 2004     

Effect of compatibilizer on morphology and properties of HDPE/Nylon 6 blends

The compatibilization effect of linear low‐density polyethylene‐grafted maleic anhydride (LLDPEgMA) and high‐density polyethylene‐grafted maleic anhydride (HDPEgMA) on high‐density polyethylene (HDPE)/polyamide 6 (Nylon 6) blend system is investigated. The morphology of 45 wt %/55 wt % polyethylene/Nylon 6 blends with three compatibilizer compositions (5 wt %, 10 wt %, and 15 wt %) are characterized by atomic force microscopic (AFM) phase imaging. The blend with 5 wt % LLDPEgMA demonstrates a Nylon 6 continuous, HDPE dispersed morphology. Increased amount of LLDPEgMA leads to sharp transition in morphology to HDPE continuous, Nylon 6 dispersed morphology. Whereas, increasing HDPEgMA concentration in the same blends results in gradual morphology transition from Nylon 6 continuous to co‐continuous morphology. The mechanical properties, oxygen permeability, and water vapor permeability are measured on the blends which confirm the morphology and indicate that HDPEgMA is a better compatibilizer than LLDPEgMA for the HDPE/Nylon 6 blend system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 281–290     

Thermal stability and toughening of epoxy resin with polysulfone resin

The cure behavior, thermal stability, and mechanical properties of diglycidylether of bisphenol A (DGEBA)/polysulfone (PSF) blends initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate as a cationic latent catalyst were investigated. The DGEBA/PSF content was varied within 100/0–100/40 wt %. Latent properties were studied through the measurement of the conversion as a function of the curing temperature, and the cure activation energy (E_a) was studied by the Kissinger method with a dynamic differential scanning calorimetry analysis. The thermal stabilities, largely based on the integral procedural decomposition temperature (IPDT) and decomposed activation energy (E_t), were investigated by the measurement of thermogravimetric analysis. For the mechanical properties of the casting specimens, the critical stress intensity factor (K_IC) test was performed, and their fractured surfaces were examined with scanning electron microscopy. E_a, IPDT, E_t, and K_IC increased with PSF increasing in the neat epoxy resin up to 30 wt %. However, there was a marginal decrease in the blend system in both the thermal and mechanical properties due to the phase separation between DGEBA and PSF. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 121–128, 2001     

Thermal,mechanical, and morphological properties of novolac‐type phenolic resin blended with fullerenol polyurethane and linear polyurethane

Fullerenol polyurethane (C₆₀‐PU) and linear polyurethane (linear‐PU) modified phenolic resins were prepared in this study. Phenolic resin/C₆₀‐PU and phenolic resin/linear‐PU blends show good miscibility as a result of the intermolecular hydrogen bonding existing between phenolic resin and PU modifiers. DSC and thermogravimetric analysis methods were used to study the thermal properties of phenolic resin blended with different types of PUs. The intermolecular hydrogen bonding that existed between phenolic resin and C₆₀‐PU was investigated by Fourier transform infrared spectroscopy. The morphology and mechanical properties of phenolic resin/C₆₀‐PU and phenolic resin/linear‐PU blends were also investigated. The char yield of the modified phenolic resins decreased with increasing PU modifier content. Significant improvement in the toughness of the modified phenolic resins was observed. The improvements of impact strength were 27.4% for the phenolic resin/linear‐PU system and 54.3% for the phenolic resin/C₆₀‐PU system, respectively, both with 3 phr linear‐PU and C₆₀‐PU content. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2436–2443, 2001     

Free volume changes on optical switching in azobenzene‐polymethylmethacrylate blends studied by a pulsed low‐energy positron beam

Polymers including chromophores, which can be switched by light, have been studied extensively during the last years due to a host of potential applications which arise from the marked changes in physical properties on switching. Even though there is clear evidence that the free volume has a significant influence on the isomerization kinetics, the question of free volume changes on switching was only addressed recently. Using a pulsed low‐energy positron beam the ortho‐positronium lifetime τ₃ was taken as a very sensitive free volume probe, and no change in free volume was detected on isomerization in an azobenzene‐polymethylmethacrylate (PMMA) copolymer containing about 8 wt % of the azobenzene moiety. Here, we report for the first time on free volume changes in an azobenzene‐PMMA blend with an azobenzene moiety concentration as high as 40 wt %. Using the same pulsed low‐energy positron beam, small but significant changes of τ₃ were observed between the structurally relaxed dark and the UV‐illuminated states suggesting a decrease in free volume of the order of 10%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Organic–inorganic polymeric nanocomposites involving novel titanium tetraisopropylate in polyethylene–octene elastomer

The new nanocomposites, by means of an in situ sol–gel process consisting of metallocene polyethylene–octene elastomer (POE) and titanium tetraisopropylate (TTIP), were investigated. In addition, the acrylic acid grafted POE (POE‐g‐AA) was studied as an alternative to POE. Fourier transform infrared (FTIR) spectroscopy, a dynamic mechanical analyzer (DMA) spectrometer, an X‐ray diffractometer (XRD), differential scanning calorimetry (DSC), a thermogravimetric analyzer (TGA), an Instron mechanical tester, and a scanning electron microscope (SEM) were used to characterize and examine the samples. The results indicate that the POE‐g‐AA/TiO₂ hybrid could have a positive effect on the properties of the POE/TiO₂ hybrid because the carboxylic acid groups of acrylic acid should act as coordination sites for the titania phase to form a Ti? O? C chemical bond. The strength of interfacial bonding between the polymer chains and the ceramic phase depended on the amount of TiO₂, as shown by the change in glass‐transition temperature (T_g) with TiO₂ content. The result of mechanical and thermal tests showed that both the tensile strength and the T_g increased to a maximum value and then decreased with an increasing of TiO₂ because excess particles (e.g., greater than 10 wt % TiO₂) might cause separation or segregation between the organic and inorganic phases. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4272–4280, 2004     

A polymer of bisphenol A and bisphenol A diglycidyl ether and its blends with poly(styrene‐co‐acrylonitrile): In situ polymerization preparation,morphology, and mechanical properties

The poly(hydroxy ether of bisphenol A)‐based blends containing poly(acrylontrile‐co‐styrene) (SAN) were prepared through in situ polymerization, i.e., the melt polymerization between the diglycidy ether of bisphenol A (DGEBA) and bisphenol A in the presence of poly(acrylontrile‐co‐styrene) (SAN). The polymerization reaction started from the initial homogeneous ternary mixture of SAN/DGEBA/bisphenol A, and the phenoxy/SAN blends with SAN content up to 20 wt % were obtained. Both the solubility behavior and Fourier transform infrared (FTIR) spectroscopy studies demonstrate that no intercomponent reaction occurred in the reactive blend system. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electronic microscopy (SEM) were employed to characterize the phase structure of the as‐polymerized blends. All the blends display the separate glass transition temperatures (T_g's); i.e., the blends were phase‐separated. The morphological observation showed that all the blends exhibited well‐distributed phase‐separated morphology. For the blends with SAN content less than 15 wt %, very fine SAN spherical particles (1–3 μmm in diameter) were uniformly dispersed in a continuous matrix of phenoxy and the fine morphology was formed through phase separation induced by polymerization. Mechanical tests show that the blends containing 5–15 wt % SAN displayed a substantial improvement of tensile properties and Izod impact strength, which were in marked contrast to those of the materials prepared via conventional methods. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 525–532, 1999     

Dynamic mechanical properties of isotactic polypropylene/nitrile rubber blends: Effects of blend ratio,reactive compatibilization,and dynamic vulcanization

The effect of blend ratio and compatibilization on dynamic mechanical properties of PP/NBR blends was investigated at different temperatures. The storage modulus of the blend decreased with increase in rubber content and shows two T_g's indicating the incompatibility of the system. Various composite models have been used to predict the experimental viscoelastic data. The Takayanagi model fit well with the experimental values. The addition of phenolic modified polypropylene (Ph-PP) and maleic modified polypropylene (MA-PP) improved the storage modulus of the blend at lower temperatures. The enhancement in storage modulus was correlated with the change in domain size of dispersed NBR particles. The effect of dynamic vulcanization using sulfur, peroxide, and mixed system on viscoelastic behavior was also studied. Among these peroxide system shows the highest modulus. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2309–2327, 1997     

Low‐temperature route to thermoplastic polyamide elastomers

Thermoplastic polyamide elastomers were obtained by polymerization of aminobenzoyl‐substituted telechelics derived from poly(tetrahydrofuran)‐diols (number‐average molecular weight: 1400 or 2000 g mol^?1) with several diacid dichlorides (terephthaloyl dichloride, 4,4′‐biphenyldicarbonyl dichloride, or 2,6‐naphthalenedicarbonyl dichloride) and chlorotrimethylsilane in N,N‐dimethylacetamide at 0–20 °C. The as‐prepared polymers had melting temperatures above 190 °C and exhibited elastic properties at room temperature, as evidenced by dynamic mechanical analysis and stress–strain measurements. The polymer with 2,6‐naphthalenedicarboxamide hard segments had the widest rubbery plateau within the series, the highest extension at break, and good recovery properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1449–1460, 2004     

Anisotropic mechanical properties of thermoplastic elastomers in situ reinforced with thermotropic liquid‐crystalline polymer fibers revealed by biaxial deformations

The anisotropic mechanical properties of the thermoplastic elastomer (TPE) in situ reinforced with thermotropic liquid‐crystalline polymer (TLCP) fibers were investigated by uniaxial, strip‐biaxial, and equibiaxial tensile measurements. The in situ composite sheets were prepared from an immiscible blend of a TLCP, Rodrun LC3000, and a TPE, styrene‐(ethylene butylene)‐styrene (SEBS) triblock copolymer, by a melt extrusion process. The uniaxial orientation of the TLCP fibers in the TPE matrix generated during processing yielded a significant mechanical anisotropy in the composites. The biaxial tensile measurements clearly demonstrated the anisotropic mechanical properties of the composites: The modulus in the direction parallel to the machine direction (MD) was considerably higher than that in the transverse direction (TD), even at large deformations; in equibiaxial stretching, the yield strain in the MD was smaller than that in the TD; the composite containing 10 wt % of TLCP exhibited the highest mechanical anisotropy among the composites, with 0–30 wt % TLCP. The latter result was in accord with the SEM observation that the composite with 10 wt % of TLCP possessed the best fibrillar morphology and the highest degree of uniaxial orientation of the TLCP fibers. The yield strains in uni‐ and biaxial elongation for the composite containing 10 wt % of TLCP were almost the same as those for the neat styrene‐ethylene butylene‐styrene. The TLCP phase with good fibrillation did not appreciably alter the original yielding characteristics of the elastomer matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 135–144, 2005