Conductive Nanocomposites Based on Cellulose Nanofibrils Coated with Polyaniline-DBSA Via In Situ Polymerization

Summary: Cellulose nanofibrils (CNF) were extracted by acid hydrolysis from cotton microfibrils and nanocomposites with polyaniline doped with dodecyl benzenesulphonic acid (PANI-DBSA) were obtained by in situ polymerization of aniline onto CNF. The ratios between DBSA to aniline and aniline to oxidant were varied in situ and the nanocomposites characterized by four probe DC electrical conductivity, ultraviolet-visible-near infrared (UV-Vis - NIR) and Fourier-transform infrared (FTIR) spectroscopies and X-ray diffraction (XRD). FTIR and UV-Vis/NIR characterization confirmed the polymerization of PANI onto CNF surfaces. Electrical conductivity of about 10⁻¹ S/cm was achieved for the composites; conductivity was mostly independent of DBSA/aniline (between 2 and 4) and aniline/oxidant (between 1 and 5) molar ratios. X-ray patterns of the samples showed crystalline peaks characteristic of cellulose I for CNF samples, and a mixture of both characteristic peaks of PANI and CNF for the nanocomposites. Field emission scanning electron microscopy (FESEM) characterization corroborated the abovementioned results showing that PANI coated the surface of the nanofibrils.     

聚苯胺/离子液体/蒙脱土纳米复合材料的制备及其导电性能研究

采用1-羧甲基-3-甲基咪唑氯化盐离子液体对钠化蒙脱土进行插层改性,然后用苯胺的盐酸溶液进行二次插层,以过硫酸铵为氧化剂,盐酸溶液为掺杂剂,使进入离子液体/蒙脱土(CMMIm/MMT)层间的苯胺(An)发生氧化聚合反应,制备了一种具有良好导电性的聚苯胺/离子液体/蒙脱土复合材料(PANI/CMMIm/MMT).用红外光谱、X-射线衍射,热重分析和DSC对样品进行了表征.结果表明当离子液体/蒙脱土用量为7.5%、盐酸浓度为1mol/L、过硫酸铵与苯胺的摩尔比为1∶1、0℃下反应6h时制备的PANI/CMMIm/MMT纳米复合材料电导率最高,达到了0.3S/cm,是相同条件下聚苯胺/钠化蒙脱土纳米复合材料电导率的2.5倍,聚苯胺的7.5倍.     

Synthesis and characterization of red mud/polyaniline composites: Electrical properties and thermal stability

New types of conducting composites using red mud as an inorganic substrate and polyaniline as the conducting phase were prepared. Red mud/polyaniline (RM/PANI) composites were synthesized in acidic aqueous solution by the chemical oxidative polymerization of aniline using ammonium peroxydisulfate as the oxidant. The composites exhibit conductivities in the 0.42-5.2 S cm⁻¹ range, depending on the amount of polyaniline. They were characterized by infrared and UV-vis spectroscopy, scanning electron microscopy and X-ray diffraction. The IR and X-ray results show that PANI is deposited on the RM surface. The composites have a globular structure and the PANI globules synthesized on the surface of RM are smaller than those prepared under the same conditions without the substrate. Thermogravimetric analysis was used for investigation of the thermal stability of the composites. The thermal stability of the conductivity of RM/PANI composites was studied by ageing at 125 °C, the conductivity being measured in situ during this process.     

Preparation and characterization of polyaniline-containing Na-AlMCM-41 as composite material with semiconductor behavior

Composite material formed from a mesoporous aluminosilicate, Na-AlMCM-41, with conducting polyaniline (PANI) has been synthesized by an in situ polymerization technique. Studies of aniline adsorption over mesoporous Na-AlMCM-41 synthesized in our laboratory allowed us to find the modes in which aniline interacts with the active sites of Na-AlMCM-41. In order to obtain the best reaction conditions to polymerize aniline onto Na-AlMCM-41, aniline was first polymerized to produce pure PANI. Hence, the oxidative in situ polymerization was carried out by two procedures, differing in the polymerization time and in static or stirring conditions. Studies of infrared spectroscopy and UV-vis spectroscopy indicated that higher polymerization time and static conditions allowed us to obtain mainly polyaniline in emeraldine form on the host. The N(2) isotherm of the polyaniline/Na-AlMCM-41 composite (PANI/MCM) indicated that the shape was similar to that of MCM, but the shift to saturation transition to lower partial pressure shows that the channels are occupied by PANI and they are now narrowed. The thermal properties of PANI, Na-AlMCM-41, and composite were investigated by TGA analyses and we found that the polymer shows higher thermal stability when it is forming the composite. Scanning electron microscopy indicated that PANI is not on the outer surface of the host. Conductivity studies show that PANI/Na-AlMCM-41 exhibits semiconductor behavior at room temperature and its conductivity was 7.0 x 10(-5) S/cm, smaller than that of pure polyaniline. PANI/Na-AlMCM-41 conductivity shows an increase as temperature increases. Magnetic measurements at room temperature confirmed that the composite has paramagnetic behavior; at lower temperatures the composite became diamagnetic.     

Effects of polymerization media on the nanoscale conductivity and current-voltage characteristics of chemically synthesized polyaniline films

A current sensing atomic force microscope (CS-AFM) was used to probe the conducting homogeneity and band structures of fully doped polyaniline (PANI) films prepared from in situ chemical polymerization/deposition of aniline on indium tin oxide in various inorganic acids. The charge transport properties of PANI films depend on the film thickness as well as polymerization medium. Fluctuations in conductivity are observed on all acid-doped PANI films and the conducting homogeneity was dependent on the film thickness: the conductivity of thick film is more uniform. The current-voltage (I-V) characteristics of all thick (>200 nm) films displayed a metal-like behavior and conductivity as high as 40 S/cm was detected in high conducting regions of film thicker than 400 nm. Whereas thin (<120 nm) films revealed insulating, semiconducting, and semimetal conducting, wide distribution in conductivity and interband distances (estimated from the I-V ordI/dV-V curves) was found. The interband distances is 0-1.35, 0-1.0, and 0-0.78 eV for thin PANI film prepared from HCl(aq), HClO(4)(aq), and H2SO4(aq), respectively. PANI film (260 nm) prepared from H2SO4(aq) revealed fiberlike morphology, and compared to PANI films prepared from HCl(aq) and HClO4(aq) with similar thickness, it has higher average nanoscale conductivity but lower bulk conductivity. This result could be direct evidence which supports that the bulk conductivity of PANI depended on the carriers hopping between the conducting domains.     

Strong adhesion and smooth conductive surface via graft polymerization of aniline on a modified glass fiber surface

The goal of this paper is to prepare surface-conductive glass fibers. The fibers were first hydroxylated, after which they were reacted with 3-bromopropyltrichlorosilane to form a bromopropylsilane monolayer, which was further reacted with aniline to substitute the bromine atoms. The surface-bound aniline molecules were used as active sites for the graft polymerization of polyaniline (PANI). The composition, structure and the morphology of the modified glass fiber surface were examined by X-ray photoelectron spectroscopy, scanning electron microscopy, and Fourier transform infrared spectroscopy. The method generated a smooth and homogenous thin layer of PANI on the surface of the glass fiber with a surface conductivity of about 6 S/cm, hence larger than the usual value ( approximately 1 S/cm) of the bulk polyaniline.     

Preparation and characterization of PVC/PANI conductive composite with extremely low percolation threshold

Aniline was polymerized in the presence of poly(vinyl chloride) (PVC) powders in hydrochloric acid to in situ prepare poly(vinyl chloride)/polyaniline (PVC/PANI) composite particles. UV‐vis spectra and FT‐IR spectra indicate PANI in PVC/PANI composite particles possessed a higher oxidation state with decreased aniline content in reactants. Both conductivity and impact strength of the dodecylbenzenesulfonic acid (DBSA) doped PANI composites (PVC/PANI‐DBSA), which were compression molded from the in situ prepared PVC/PANI particles, increase with the pressing temperature and decrease with the increase of DBSA doped PANI (PANI‐DBSA) loading. An excellent electric conductivity of 5.06 × 10^?2 S/cm and impact strength of 0.518 KJ/m² could be achieved for the in situ synthesized and subsequently compression molded composite. Copyright © 2004 John Wiley & Sons, Ltd.     

Chemically modified polyaniline nanocomposites by poly(2-acrylamido-2-methyl-1-propanesulfonicacid)/graphene nanoplatelet

New conducting polyaniline (PANI) nanocomposites that were chemically modified by poly(2-acrylamido-2-methyl-1-propanesulfonicacid) (PMP) and graphene nanoplatelets (GNPs) were prepared via in situ deposition. PMP was first synthesized using GNPs, and aniline hydrochloride monomer was then polymerized in the presence of PMP-GNPs. The nanopolymer composites were characterized, and its structural morphology was analyzed via transmission electron microscopy and scanning electron microscopy. Fourier transformation infrared spectroscopy results indicate a strong interaction between PANI, PMP, and GNPs. To understand the conduction behavior of the composites, temperature-dependent DC electrical conductivity was measured between 295 K and 503 K, and the mechanism of transport properties of the new composites was analyzed by Mott’s variable range of hopping model. The PANI/PMP-GNP showed higher conductivity than pure PANI polymer. The high electrical conductivity of the nanocomposites may be useful in fabricating multifunctional materials in bulk for future technological applications.     

Synthesis of ordered mesoporous zirconium phosphate films by spin coating and vapor treatments

Ordered mesoporous zirconium phosphate films were prepared on a silicon substrate by spin coating using a mixture of zirconium isopropoxide, triethyl phosphate, Pluronic P123 triblock copolymer, nitric acid, ethanol, and water. The spin-on film was consecutively treated with vapors of phosphoric acid and ammonia. The post-vapor treatments effectively enhanced the thermal stability of an ordered mesostructure when heated to 500 degrees C. XRD and TEM analyses show that the calcined zirconium phosphate film has a hexagonal structure with straight channels parallel to the film surface. The zirconium phosphate film exhibited high proton conductivity of 0.02 S/cm parallel to the film surface at 80% RH and 25 degrees C.     

Post-synthetic Modification of Covalent Organic Frameworks through in situ Polymerization of Aniline for Enhanced Capacitive Energy Storage

Covalent organic frameworks (COFs) having layered architecture with open nanochannels and high specific surface area are promising candidates for energy storage. However, the low electrical conductivity of two-dimensional COFs often limits their scope in energy storage applications. The conductivity of COFs can be enhanced through post-synthetic modification with conducting polymers. Herein, we developed polyaniline (PANI) modified triazine-based COFs via in situ polymerization of aniline within the porous frameworks. The composite materials showed high conductivity of 1.4–1.9×10⁻² S cm⁻¹ at room temperature with a 20-fold enhancement of the specific capacitance than the pristine frameworks. The fabricated supercapacitor exhibited a high energy density of 24.4 W h kg⁻¹ and a power density of 200 W kg⁻¹ at 0.5 A g⁻¹ current density. Moreover, the device fabricated using the conducting polymer-triazine COF composite could light up a green light-emitting diode for 1 min after being charged for 10 s.     

A Conductive polylactic acid/polyaniline porous scaffold via freeze extraction for potential biomedical applications

This paper reports for the first time a simple yet effective method for fabricating a conductive and highly porous scaffold material made up of polylactic acid (PLA) and conducting polyaniline (PANI). The electrical percolation state was successfully obtained at 3 wt% of PANI inclusions and reached a conductivity level of useable tissue engineering applications at 4 wt%. In addition, preliminary bioactivity test results indicated that the protonating agent could form a chelate at the scaffold surface leading to good in-vitro apatite forming ability during biomimetic immersion. This new conductive scaffold has potential as a suitable biomedical material that requires electrical conductivity.     

Facile synthesis of polyaniline nanofibers using chloroaurate acid as the oxidant

This work demonstrated a facile route to the synthesis of polyaniline (PANI) nanofibers by polymerization of aniline using chloroaurate acid (HAuCl(4)) as the oxidant. The reduction of AuCl(4)(-) is accompanied by oxidative polymerization of aniline, leading to uniform PANI nanofibers with a diameter of 35 +/- 5 nm and aggregated gold nanoparticles which can precipitate from the liquid phase during the reaction. The resultant PANI nanofibers and gold particles were characterized by means of different techniques, such as UV-vis, FTIR spectroscopy, and scanning and transmission electron microscopy methods. It is found that the gold aggregates are capped with polyaniline, and the conductivity of the fibers is around 0.16 S/cm.     

An elastomeric conducting composite based on polyaniline coated nylon fiber and chloroprene rubber

Chloroprene rubber-polyaniline (PANI) coated nylon fiber composites containing PANI powder were prepared by mechanical mixing on a two-roll mill. PANI was synthesized by chemical polymerization of aniline in presence of hydrochloric acid. PANI coated nylon fiber was prepared by in situ polymerization of aniline on nylon fiber. The cure parameters cure kinetics, filler dispersion, mechanical properties, DC electrical conductivity and thermal degradation parameters of the composites were evaluated. Cure rate index and cure reaction constants indicated that the rate of cure reaction changes on filler addition. Filler addition at higher loadings led to agglomeration. The tensile strength and modulus values increased suggesting a reinforcement effect. The conductivity, thermal characteristics and thermal degradation kinetic parameters are also presented.     

Reduction of silver nitrate by polyaniline nanotubes to produce silver-polyaniline composites

Polyaniline (PANI) nanotubes were prepared by oxidation of aniline in 0.4 M acetic acid. They were subsequently used as a reductant of silver nitrate in 1 M nitric acid, water or 1 M ammonium hydroxide at various molar ratios of silver nitrate to PANI. The resulting PANI-silver composites contained silver nanoparticles of 40–60 nm size along with macroscopic silver flakes. Under these experimental conditions, silver was always produced outside the PANI nanotubes. Changes in the molecular structure of PANI were analyzed by FTIR spectroscopy. Silver content in the composites was determined as a residue by thermogravimetric analysis, and confirmed by density measurements. The highest conductivity of a composite, 68.5 S cm⁻¹, was obtained at the nitrate to PANI molar ratio of 0.67 in water. Also, the best reaction yield was obtained in water. Reductions performed in an acidic medium gave products with conductivity of 10⁻⁴–10⁻² S cm⁻¹, whereas the reaction in alkaline solution yielded non-conducting products.     

Influence of graphene reinforcement in conductive polymer: Synthesis and characterization

Lightweight conductive polymers are considered for lightning strike mitigation in composites by synthesizing intrinsically conductive polymers (ICPs) and by the inclusion of conductive fillers in insulating matrices. Conductive films based on polyaniline (PANI) and graphene have been developed to improve through‐thickness conductivity of polymer composites. The result shows that the conductivity of PANI enhanced by blending polyvinylpyrrolidone (PVP) and PANI in 3:1 ratio. Conductive composite thin films are prepared by dispersing graphene in PANI. The conductivity of composite films was found to increase by 40× at 20 wt% of graphene inclusion compared with PVP and PANI blend. Fourier‐transform‐infrared (FTIR) spectra confirmed in situ polymerization of the polymer blend. The inclusion of graphene also exhibits an increase in Tg by 21°C. Graphene additions also showed an increase in thermal stability by approximately 148°C in the composite films. The mechanical result obtained from DMA shows that inclusion of graphene increases the tensile strength by 48% at 20 wt% of graphene reinforcement. A thin, highly conductive surface that is compatible with a composite resin system can enhance the surface conductivity of composites, improving its lightning strike mitigation capabilities.     

Polyaniline-coated coconut fibers: Structure,properties and their use as conductive additives in matrix of polyurethane derived from castor oil

Electrically conducting fibers based on coconut fibers (CF) and polyaniline (PANI) were prepared through in situ oxidative polymerization of aniline (ANI) in the presence of CF using iron (III) chloride hexahydrate (FeCl_3.6H₂O) or ammonium persulfate (APS) as an oxidant. The PANI-coated coconut fibers (CF-PANI) displayed various morphologies, electrical conductivities and percentages of PANI on the CF surface. For both systems, a PANI conductive layer was present on the CF surface, which was responsible for an electrical conductivity of around 1.5 × 10⁻¹ and 1.9 × 10⁻² S cm⁻¹ for composites prepared with FeCl₃.6H₂O and APS, respectively; values that are similar to that of pure PANI. In order to modify the structure and properties of polyurethane derived from castor oil (PU) both CF-PANI and pure PANI were used as conductive additives. The PU/CF-PANI composites exhibited higher electrical conductivity than pure PU and PU/PANI blends. Additionally, the PU/CF-PANI composites showed a variation in electrical resistivity according to the compressive stress applied, indicating that these materials could be applied for pressure-sensitive applications.     

Electrical Properties Investigation in PA12/PANI Composites

Summary: Volume conducting PA-12 based composites powders were chemically prepared by in situ polymerization and aniline doping at room temperature. These kinds of polyamide / PANI composites were investigated regarding their electrical properties. Their ac and dc electrical properties measured in the frequency range of 10⁻²–10⁷ Hz are reported and the frequency dependence of electrical conductivity was investigated as a function of PANI concentration leading to the determination of the conductivity. The experimental conductivity was found to increase continuously with PANI content and explained by percolation theory with a relatively low percolation threshold of about 0.4 wt.%. The dielectric behavior of various PANI polymer composites has been characterized by the critical frequency ω_c (denoting the crossover from the dc plateau of the conductivity to its frequency dependent ac behaviour). Modelling the conductivity behavior versus volume fraction using Slupkowski approach has revealed that the considered parameters are not sufficient to describe the electrical conductivity behavior.     

BrΦnsted酸性离子液体掺杂聚苯胺的无溶剂制备及其表征

首先合成了两种带—SO3H官能团的Brφnsted酸离子液体([MIMPS][HSO4]和[PYPS][HSO4]),然后分别以这两种带—SO3H官能团的Brφnsted酸性离子液体做为掺杂剂,在无溶剂条件下通过机械化学聚合反应制备了掺杂导电态聚苯胺.由于带—SO3H官能团的Brφnsted酸性离子液体中H+可以单独以离子形式存在,因此可形成质子化导电态的翠绿亚胺盐,并以红外光谱、紫外可见-近红外、X-射线衍射、循环伏安和四探针技术等测试方法对聚苯胺进行了结构和性能表征.PANI-[MIMPS][HSO4]的结晶性、电导率和电化学活性要优于PANI-[PYPS][HSO4].     

Synthesis of polyaniline and application in the design of formulations of conductive paints

Polyaniline (PANI) is prepared by chemical polymerization of aniline in acidic medium using ammonium peroxydisulfate ((NH₄)₂S₂O₈) as oxidant. The polymer, with a conductivity of 25–30 S/cm, is used to formulate conducting paints. A stable paint with a conductivity of 10^?3 S/cm is obtained. Copyright © 2004 John Wiley & Sons, Ltd.     

合成聚苯胺/碳化钨复合材料及聚合机理探讨

采用在原位聚合苯胺的反应介质中分散碳化钨(WC)的方法制备了掺杂聚苯胺/碳化钨(PANI/WC)复合物,并研究了苯胺在WC表面的聚合机理.通过扫描电镜(SEM)、透射电镜(TEM)、傅立叶红外光谱(FTIR)、拉曼光谱(Raman)和X射线衍射(XRD)对复合物进行了表征.结果表明,苯胺的聚合倾向于在WC颗粒表面进行,形成了PANI包覆WC的复合材料;WC粒子与PANI大分子之间存在强的相互作用,并且复合前后WC的晶型并未发生变化,WC的存在导致红外光谱有明显的蓝移现象,复合后在3446 cm-1处的红外吸收峰变得很弱;在拉曼光谱中,代表醌环C N键的伸缩振动峰红移了9 cm-1,并且强度也有很大程度提高.说明PANI与WC之间有化学键的作用,它们之间的化学键作用发生在C N键的N原子上.聚合反应优先在WC粒子表面进行,生成PANI包覆结构,并提出了PANI/WC复合物的形成机制.