Preparation of TiO<Subscript>2</Subscript>/activated carbon with Fe ions doping photocatalyst and its application to photocatalytic degradation of reactive brilliant red K2G

Titanium dioxide coated on activated carbon (AC) with Fe ions doping (Fe-TiO₂/AC) composite was prepared by an improved sol-gel method. The photocatalytic activities were tested by photocatalytic degradation of reactive brilliant red K2G in solution. The results show that in comparison with the agglomeration of pure TiO₂, the TiO₂ nanoparticles are well dispersed in the AC matrix, of which sizes are decreased with Fe ions doping. Additionally, the iron species on TiO₂ of composite are Fe₂O₃ and FeO, which do not affect the crystalline structures of TiO₂ nanoparticles. The AC matrix and iron doping content influence the fluorescence intensity of composite due to their effects on recombination probability of hole-electron pairs. Compared with TiO₂, 0.3% Fe-TiO₂, TiO₂/AC, 0.5% Fe-TiO₂/AC and 0.1% Fe-TiO₂/AC, the 0.3% Fe-TiO₂/AC shows the highest photoactivity with the complete mineralization of K2G for finite time due to the optimum Fe ions content and AC matrix. Furthermore, the kinetic constant (k = 0.0229 min⁻¹) of 0.3% Fe-TiO₂/AC composite is more than the sum of both TiO₂/AC (0.0154 min⁻¹) and 0.3% Fe-TiO₂ (0.0057 min⁻¹) because coexistence of the AC and Fe ions has an enlarging effect on improving the photoactivity of TiO₂. Supported by the Education Department Foundation of Hunan Province (Grant No. 08B063) and Science and Natural Science Foundation of Hunan Province (Grant No. 09JJ6101)     

The protection effect of β-CD on DNA damage induced by ultrafine TiO2

Under the photocatalysis of 365 nm ultraviolet radiation, ultrafine TiO2 caused the oxidative damage of Teasy plasmid DNA. The damage was determined by gel-electrophoresis. Then, a different dose of β-CD was added to the reaction, and the damage was restrained. The rate of damage restraining reached 97% when the mass of β-CD was 4 times as that of TiO2. Through UV scan and IR spectroscopy, it was found that the Ti-O of ultrafine TiO2 was bound with -OH of β-CD cavum and the -OH on the surface of ultrafine TiO2 disappeared, so the formation of · OH was controlled. The ultrafine TiO2 has been widely used, but it was determined to be carcinogenic by some research. The protection effect of β-CD to DNA in the molecular level takes a new look on the surface modification of nano particles to decrease the toxic effect.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

Effect of PEG with different <Emphasis Type="Italic">M</Emphasis><Subscript>W</Subscript> as template direction reagent on preparation of porous TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> with assistance of supercritical CO<Subscript>2</Subscript>

Titania–silica composite have been prepared using polyethylene glycol (PEG) with different molecular weights (M _w), PEG20000, PEG10000, and PEG2000, as template in supercritical carbon dioxide (SC CO₂). The composite precursors were dissolved in SC CO₂ and impregnated into PEG templates using SC CO₂ as swelling agent and carrier. After removing the template by calcination at suitable temperature, the titania–silica composite were obtained. The composite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and nitrogen sorption–desorption experiment. Photocatalytic activity of the samples has been investigated by photodegradation of methyl orange. Results indicate that there are many Si–O–Ti linkages in the TiO₂/SiO₂ composite; the PEG template has a significant influence on the structure of TiO₂/SiO₂. In addition, the TiO₂/SiO₂ prepared with PEG10000 exhibited high photocatalytic efficiency. So this work supplies a clue to control and obtain the TiO₂/SiO₂ composite with different photocatalytic reactivity with the aid of suitable PEG template in supercritical CO₂.     

FTIR-ATR <Emphasis Type="Italic">in situ</Emphasis> observation on the efflorescence and deliquescence processes of Mg(NO<Subscript>3</Subscript>)<Subscript>2</Subscript> aerosols

The efflorescence and deliquescence processes of Mg(NO₃)₂ aerosol particles deposited on ZnSe substrate have been investigated through in situ Fourier transform infrared-attenuated total reflection (FTIR-ATR) technique at the molecular level. At relative humidity (RH) of ∼3%, Mg(NO₃)₂ particles existed as amorphous states. The amorphous Mg(NO₃)₂ particles were transformed into crystalline Mg(NO₃)₂ · nH₂O (n ≤ 5) with slight increasing of RH. Thermodynamically stable Mg(NO₃)₂·6H₂O crystals were gradually formed on the particle surface and started to be dissolved at the saturation point (∼53% RH). At the same time, a continuous phase transition from Mg(NO₃)₂ · nH₂O (n≤5) to Mg(NO₃)₂·6H₂O occurred on the particle surface. This led the solid particles to completely deliquesce at 76% RH, which was much higher than the saturation point of 53% RH. In the efflorescence process, Mg(NO₃)₂ droplets entered into the supersaturated region due to the gradual evaporation of water. Finally, amorphous particles were formed when RH decreased below 5%. In the FTIR-ATR spectra of the supersaturated Mg(NO₃)₂ droplets, the absorbance of the symmetric stretching vibration of NO ₃ ⁻ (v ₁- NO ₃ ⁻ ) clearly became stronger. It resulted from the continuous formation of solvent share ion pairs (SIPs), and even the contact ion pairs (CIPs) between Mg²⁺ and NO ₃ ⁻ . Supported by the Trans-Century Program Foundation for the Talents by the Ministry of Education of China, the National Natural Science Foundation of China (Grant Nos. 20073004, 20473012, and 20673010), the 111 Project (B07012), and the State Key Laboratory of Physical Chemistry for Solid Surface of Xiamen University     

Hydrothermal synthesis,structure and photocatalytic property of nano-TiO<Subscript>2</Subscript>-MnO<Subscript>2</Subscript>

TiCl₄ and MnSO₄· H₂O as raw materials are hydrolyzed stiochiometrically, following the intermediate of oxide hydrating reacts at 150°C, 0.5 MPa in high-pressure reactor, after filtering, washing and drying, nanometric TiO₂-MnO₂ (Ti_1-X Mn _X O₂) is prepared. The effects of the reaction temperature and time on nanometric TiO₂-MnO₂ are also discussed. XRD shows that the product is TiO₂-MnO₂ with amorphous phase. After being sintered at above 780 °C, it transfers into Ti_1-X Mn _X O₂ with a rutile structure. TEM shows that TiO₂-MnO₂ is the spherical particle. And the average diameter of the particles is 20 nm. The optical absorbance was determined by UV-265 spectrophotometer after dispersing the sample in the mixture of water and glycerol with the ratio of 1 : 1 equably. It is found that the nano-material possesses the advantages of both nano-TiO₂ and nano-MnO₂, and it has strong absorption in the UV and visible region. Photodegradation of dyes in an aqueous solution is investigated using nanometricTiO₂-MnO₂ as a photocatalyst. The results show that after 60 min illumination, the decolorization rate of the acidic red B and acidic black 234 dye can be as high as 100%.     

Photocatalytic intercalated material based on HLaNb<Subscript>2</Subscript>O<Subscript>7</Subscript> as host and Cd<Subscript>0.8</Subscript>Zn<Subscript>0.2</Subscript>S as guest

A novel photocatalytic material (Pt,Cd0.8Zn0.2S)/HLaNb2O7 was fabricated by successive intercalation and exchange reactions. The (Pt,Cd0.8Zn0.2S)/HLaNb2O7 possessed a gallery height less than 0.5 nm and showed a broad absorption with wavelength over 370-500 nm. Using (Pt,Cd0.8Zn0.2S)/HLaNb2O7 as catalyst, the photocatalytic H2 evolution was more than 160 cm3·h-1·g-1 in the presence of Na2S as a sacrificial agent under irradiation with wavelength more than 290 nm from a 100-W mercury lamp. Furthermore, the catalyst showed photocatalytic activity even under visible light irradiation.     

Thermal oxide synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanowires

Fe₃O₄ nanorods and Fe₂O₃ nanowires have been synthesized through a simple thermal oxide reaction of Fe with C₂H₂O₄ solution at 200–600°C for 1 h in the air. The morphology and structure of Fe₃O₄ nanorods and Fe₂O₃ nanowires were detected with powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The influence of temperature on the morphology development was experimentally investigated. The results show that the polycrystals Fe₃O₄ nanorods with cubic structure and the average diameter of 0.5–0.8 μm grow after reaction at 200–500°C for 1 h in the air. When the temperature was 600°C, the samples completely became Fe₂O₃ nanowires with hexagonal structure. It was found that C₂H₂O₄ molecules had a significant effect on the formation of Fe₃O₄ nanorods. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ nanorods. Supported by the Fund of Weinan Teacher’s University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and the Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Influence of NH<Subscript>3</Subscript>-treating temperature on visible light photocatalytic activity of N-doped P<Subscript>25</Subscript>-TiO<Subscript>2</Subscript>

The influence of NH₃-treating temperature on the visible light photocatalytic activity of N-doped P₂₅-TiO₂ as well as the relationship between the surface composition structure of TiO₂ and its visible light photocatalytic activity were investigated. The results showed that N-doped P₂₅-TiO₂ treated at 600°C had the highest activity. The structure of P₂₅-TiO₂ was converted from anatase to rutile at 700°C. Moreover, no N-doping was detected at the surface of P₂₅-TiO₂. There was no simply linear relationship between the visible light photocatalytic activity and the concentration of doped nitrogen, and visible light absorption. The visible light photocatalytic activity of N-doped P₂₅-TiO₂ was mainly influenced by the synergistic action of the following factors: (i) the formation of the single-electron-trapped oxygen vacancies (denoted as V_o^·); (ii) the doped nitrogen on the surface of TiO₂; (iii) the anatase TiO₂ structure.     

Structural characterization and photocatalytic properties of novel Bi<Subscript>2</Subscript>FeVO<Subscript>7</Subscript>

Bi₂FeVO₇ was prepared by a solid-state reaction technique for the first time and the structural and photocatalytic properties of Bi₂FeVO₇ were studied. The results shows that this compound crystallized in the tetragonal crystal system with space group I4/mmm. Moreover, the band gap of Bi₂FeVO₇ was estimated to be about 2.22(6) eV. For the photocatalytic water splitting reaction, H₂ or O₂ evolution was observed from pure water with Bi₂FeVO₇ as the photocatalyst by ultraviolet light irradiation. Degradation of aqueous methylene blue (MB) dye by photocatalytic way over this compound was further studied under visible light irradiation. Bi₂FeVO₇ shows higher catalytic activity compared to TiO₂ (P-25) for MB photocatalytic degradation under visible light irradiation. Complete removal of aqueous MB was realized after visible light irradiation for 170 min with Bi₂FeVO₇ as the photocatalyst. The reduction of the total organic carbon (TOC) and the formation of inorganic products, SO ₄ ²⁻ and NO ₃ ⁻ revealed the continuous mineralization of aqueous MB during the photocatalytic course.     

Photocatalytic reduction of CO<Subscript>2</Subscript> over TiO<Subscript>2</Subscript> based catalysts

At present, carbon dioxide is considered the largest contributor among greenhouse gases. This review covers the current state of problem of carbon dioxide emissions from industrial and combustion processes, the principle of photocatalysis, existing literature related to photocatalytic CO₂ reduction over TiO₂ based catalysts and the effects of important parameters on the process performance including light wavelength and intensity, type of reductant, metal-modified surface, temperature and pressure. Presented at the 34th International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 21–25 May 2007.     

Synthesize TiO<Subscript>2</Subscript> microspheres self-assembled from nanorods via hydrothermal treatment

The TiO2 microspheres were deposited on the glass substrates under certain conditions via hydrothermal reaction using 0.15 mol·L-1 TiCl3 saturated NaCl aqueous solution adding urea as an additive.The TiO2 is characterized rutile by results of SEM, TEM and XRD techniques, the TiO2 microspheres are large scale assembled from TiO2 nanorods. The affections on the products by the factors of the contents of urea being an additive (the key techniques), the reaction temperature, the reaction time and the concentration of TiCl3 were studied. The optimum condition was found, and the mechanism of reactions was discussed also.     

Resonance scattering spectral detection of ultratrace IgG using immunonanogold-HAuCl<Subscript>4</Subscript>-NH<Subscript>2</Subscript>OH catalytic reaction

Nanogold particles of 10 nm were used to label goat anti-human IgG (GIgG) to obtain nanogold-labeled GIgG (AuGIgG). In a citrate-HCI buffer solution of pH 2.27, AuGIgG showed a strong catalytic effect on the reaction between HAuCl₄ and NH₂OH to form big gold particles that exhibited a resonance scattering (RS) peak at 796 nm. Under the chosen conditions, AuGIgG combined with IgG to form immunocomplex AuGIgG-IgG that can be removed by centrifuging at 16000 r/min. AuGIgG in the centrifuging solution also showed catalytic effect on the reaction. On those grounds, an immunonanogold catalytic RS assay for IgG was designed. With addition of IgG, the amount of AuGIgG in the centrifuging solution decreased; the RS intensity at 796 nm (I _{796 nm}) decreased linearly. The decreased intensity ΔI _{796 nm} was linear with respect to the IgG concentration in the range of 0.08–16.0 ng · mL⁻¹ with a detection limit of 0.02 ng · mL⁻¹. This assay was applied to analysis of IgG in sera with satisfactory sensitivity, selectivity and rapidity. Supported by the National Natural Science Foundation of China (Grant No. 20667001), Natural Science Foundation of Guangxi Province (Grant No. 0728213), and the Foundation of New Century Ten-Hundred-Thousand Talents of Guangxi Province     

Osmotic Coefficients of the Li<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript>+LiCl + H<Subscript>2</Subscript>O System at <Emphasis Type="Italic">T</Emphasis>=273.15 K

Osmotic coefficients and water activities for the Li₂B₄O₇+LiCl+H₂O system have been measured at T=273.15 K by the isopiestic method, using an improved apparatus. Two types of osmotic coefficients, φ _S and φ _E, were determined. φ _S is based on the stoichiometric molalities of the solute Li₂B₄O₇(aq), and φ _E is based on equilibrium molalities from consideration of the equilibrium speciation into H₃BO₃,B(OH)₄⁻ and B₃O₃(OH)₄⁻. The stoichiometric equilibrium constants K _m for the aqueous speciation reactions were estimated. Two types of representations of the osmotic coefficients for the Li₂B₄O₇+LiCl+H₂O system are presented with ion-interaction models based on Pitzer’s equations with minor modifications: model (I) represents the φ _S data with six parameters based on considering the ion-interactions between three ionic species of Li⁺, Cl⁻, and B₄O₇²⁻, and model (II) for represents the φ _E data based on considering the equilibrium speciation. The parameters of models (I) and (II) are presented. The standard deviations for the two models are 0.0152 and 0.0298, respectively. Model (I) was more satisfactory than model (II) for representing the isopiestic data.     

A kinetic study of the oxidation of <Emphasis Type="SmallCaps">l</Emphasis>-methionine by water soluble colloidal MnO<Subscript>2</Subscript>

Aqueous solution of water soluble colloidal MnO₂ was prepared by Perez-Benito method. Kinetics of l-methionine oxidation by colloidal MnO₂ in perchloric acid (0.93 × 10⁻⁴ to 3.72 × 10⁻⁴ mol dm⁻³) has been studied spectrophotometrically. The reaction follows first-order kinetics with respect to [H⁺]. The first-order kinetics with respect to l-methionine at low concentration shifts to zero order at higher concentration. The effects of [Mn(II)] and [F⁻] on the reaction rate were also determined. Manganese (II) has sigmoidal effect on the rate reaction and act as auto catalyst. The exact dependence on [Mn(II)] cannot be explained due to its oxidation by colloidal MnO₂. Methionine sulfoxide was formed as the oxidation product of l-methionine. Ammonia and carbon dioxide have not been identified as the reaction products. The mechanism with the observed kinetics has been proposed and discussed.     

Preparation of highly active photocatalyst anatase TiO<Subscript>2</Subscript> by mixed template method

TiO₂ nanocrystals with diameters 8–10 nm have been prepared through sol–gel method using a mixed template of polyethylene glycol (PEG) and cetytrimethylammonium bromide (CTAB) at low temperature. The samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution (HR) TEM and fourier transform infrared spectroscopy (FT-IR) etc. XRD analysis showed the TiO₂ photocatalysts prepared with mixed template are pure anatase. FTIR spectrum revealed that the cationic surfactant provides CTA⁺ molecules and bonds to Ti–O to prevent the condensation reaction. PEG plays a dispersant role in controlling the structure of nano-TiO₂ particles. CTAB and PEG incorporated with each other to restrain the growth of crystal nucleus and control the size of grain. The self-assembling process has been confirmed by HRTEM. PEG played different role in mixed template from the single template. The photocatalytic activity of samples was determined by using as a model reaction. The results showed that TiO₂ photocatalysts with mixed template have higher photocatalytic activity than P25.     

Sol–gel synthesis,characterization and photocatalytic activity of mesoporous TiO<Subscript>2</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3 </Subscript>granules

Mesoporous TiO₂/γ-Al₂O₃ composite granules were prepared by combining sol–gel/oil-drop method, using various titania solution. The product granules can be used as a photocatalyst or adsorbent in moving, fluidized bed reactors. The phase composition and pore structure of the granules can be controlled by calcination temperature and using different titania solution. In the photocatalysis of NH₃ decomposition, TiO₂/γ-Al₂O₃ granules using Degussa P25 powder treated thermally at 450 °C showed the highest catalytic ability. However, TiO₂/γ-Al₂O₃ granules using titania made by hydrothermal method had comparable performance in NH₃ decomposition.     

Synthesis and photocatalytic activity of TiO<Subscript>2</Subscript> nanoparticles fluorine-modified with TiF<Subscript>4</Subscript>

Fluorine-modified TiO₂ nan oparticles were synthesized by introducing TiF₄ as a fluorine source either before or after the sufficient hydrolysis and condensation of Ti(OEt)₄. The photocatalytic activity of the fluorine-modified catalysts was found to be greatly affected by the fluorine position in TiO₂ nanoparticles. When TiF₄ and Ti(OEt)₄ hydrolyzed with synchronization, the fluorine tended to be doped in the lattice. The formation of Ti³⁺ defects could result in charge recombination in bulk and bring down the photocatalytic activity. In contrast, if TiF₄ was introduced after the sufficient hydrolysis and condensation of Ti(OEt)₄. Ti−F bonds could exist mainly on the TiO₂ particles surface, which not only prevented the growth of anatase crystals but also facilitated the transfer of organic compounds from solution to catalyst surface by reducing the hydrophilic properties.     

Preparation of novel visible-light-driven In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaIn<Subscript>2</Subscript>O<Subscript>4</Subscript> composite photocatalyst by sol–gel method

Novel visible-light-activated In₂O₃–CaIn₂O₄ photocatalysts were developed in this paper through a sol–gel method. The photocatalytic activities of In₂O₃–CaIn₂O₄ composite photocatalysts were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 400 nm). The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and UV–vis diffused reflectance spectroscopy (DRS). The results revealed that the In₂O₃–CaIn₂O₄ composite samples with different In₂O₃ and CaIn₂O₄ content can be obtained by controlling the synthesis temperature, and the composite photocatalysts extended the light absorption spectrum toward the visible region. The photocatalytic tests indicated that the composite samples demonstrated high visible-light activity for decomposition of methyl orange. The significant enhancement in the In₂O₃–CaIn₂O₄ photo-activity under visible light irradiation can be ascribed to the efficient separation of photo-generated carriers in the In₂O₃ and CaIn₂O₄ coupling semiconductors.