工业高碳富钙型灰对准东混煤结渣特性的影响

结合灰熔融测定、固定床和一维沉降炉实验,详细研究两种工业高碳富钙型灰(除尘灰和烘干灰)分别作为添加剂对高、低钠混煤结渣特性的影响。结果表明,原混煤在取样温度1000℃时已存在大量无定型硅,升高温度这些组分极易诱发低温共融反应。添入5%除尘灰后混煤煤灰的软化温度提高幅度高达100℃,能使混煤煤灰中CaO/SiO_2质量比达到2.5,促使新相硅酸二钙和钙铝榴石生成,能够有效改善混煤的高温结渣倾向。沉降炉实验工况下探针收集灰样中主要物相均为钙铝黄长石,掺入两种添加剂后均可促使含硅物相演变为结晶矿物相,抑制非晶相含硅组分诱发的低温熔融,但添入5%烘干灰后探针表面结渣倾向改善的效果不显著。     

高碱煤含钠矿物沉积层的高温熔融及多相反应过程分析

采用纯矿物试剂模拟燃用高碱煤时炉内受热面典型的灰沉积层化学组成,利用热机械分析（TMA）、TG-DSC分析、高温煅烧实验结合XRD、SEM-EDS表征方法研究了不同Na₂SO₄含量灰沉积层的高温熔融过程及矿物间的多相反应机理。结果表明,掺混Na₂SO₄后沉积层熔化特征温度显著降低,Na₂SO₄的主要反应途径与掺混比例有关,当掺混比低于20%时,Na₂SO₄与SiO₂、CaO、Al₂O₃反应主要转变为CaSO₄和钠的硅铝酸盐;掺混比大于40%时则主要与CaSO₄生成低熔点的钠钙复合硫酸盐。富Na₂SO₄沉积层颗粒在800℃时开始黏结;900-950℃时,霞石、钠长石等钠的硅铝酸盐发生低温共熔,同时Na₂SO₄和CaSO₄生成的复合硫酸盐开始熔融,逐渐形成液相;1200-1250℃时,镁黄长石与含钙矿物发生强烈共熔,温度超过1300℃后矿物完全熔融成为自由液相。     

煤灰中矿物质组成对煤灰熔融温度的影响

选取九种不同灰熔融温度的煤样,利用X射线衍射分析方法,研究了煤灰的矿物质组成及含量对灰熔融温度的影响,以及弱还原性气氛下不同温度煤灰熔融过程中的矿物演变过程及其对灰熔融温度的影响。结果表明,815℃煤灰的主要晶体矿物质组成为石英、硬石膏、赤铁矿、氢氧钙石和石灰等。一般情况下,煤灰中氢氧钙石含量低,硬石膏和赤铁矿含量高的煤,灰熔融温度较低。在还原性气氛下,随着温度的升高,煤灰中的石英、硬石膏、氢氧钙石等结晶矿物含量逐渐减少,生成新的矿物质。莫来石的生成是导致煤灰熔融温度高的主要原因。低灰熔融温度煤灰在加热过程中,在1 100℃时,钙长石和铁钙辉石的生成起到了降低煤灰熔融温度的作用。     

准东煤掺烧高岭土对固钠率及灰熔融特性影响研究

选择常见的黏土矿物高岭土作为准东煤添加剂掺烧,研究了不同掺混比例、不同燃烧温度下添加剂的固钠率和煤灰熔融特性的变化,结合XRD谱图和三元相图研究了灰中矿物在高温下的演变过程。结果表明,固钠率随高岭土掺混比例增加逐渐增大,在0~2%时增长较快,2%~5%增长较慢,随燃烧温度升高略微下降;掺混后煤灰熔点随掺混比例先缓慢减小,再快速减小,后快速增加,在3%时达到1 200 ℃左右;XRD和三元相图分析结果表明,煤灰熔融特性变化是由于灰中硅钙石、钙黄长石和钙长石矿物比例的变化引起,发生低温共熔现象是导致掺混比例为3%和4%时煤灰熔点最低的主要原因;当掺混比例为2%时,固钠率在60%以上且灰熔点在1 300 ℃左右,利于固态排渣,当掺混比例为3.0%~4.0%时,灰熔点在1 200 ℃左右,利于液体排渣。     

水泥生料的燃烧固硫特性及其微观反应机理研究

采用SC-132定硫仪对水泥生料的燃烧固硫特性进行了评价，利用XRD、SEM对煅烧样品进行矿相组成分析及矿物形态分析，讨论了水泥生料高温固硫的微观反应机理。结果表明，高温段固硫物相的热稳定性是影响水泥生料固硫效率的决定因素。水泥生料在较宽温度范围内具有85%以上的固硫效率。850 ℃时已有CaSO4形成， 1 050 ℃时CaSO4开始分解。1050℃～1250℃生成耐高温的硫硅酸钙、硫铝酸钙等复合矿物。1300℃时铁铝酸盐固熔体等将硫酸盐的表面包裹，抑制其高温分解，使水泥生料在1300℃时仍有较高的固硫效率。     

添加煤灰及混合氧化物对石油焦CO_2高温气化反应的影响

以化学组成相近的燃烧煤灰、气化煤灰和混合氧化物为添加剂,分别通过干混法和湿混法加入石油焦中,并借助热重分析仪在1200-1400℃下进行CO_2气化实验,研究高温下煤灰掺混方式、含量及物相组成对石油焦CO_2气化的影响,并使用混合氧化物替代实际煤灰研究其对石油焦的高温气化催化作用。结果表明,石油焦气化反应速率随煤灰添加量的增加而提升;气化温度为1200、1300℃时,使用干混法和气化煤灰对石油焦的气化促进作用较弱;但气化温度为1400℃时,改变煤灰和石油焦的掺混方式及其中活性金属存在方式,对石油焦气化反应几乎没有影响。这是高温下煤灰熔融,导致液态熔体与石油焦表面接触良好、活性金属自由度高以及传质阻力增加共同作用的结果。此时混合氧化物的催化指数与混合物中铁钙含量具有线性关系,即添加高铁钙含量的煤灰可以促进石油焦CO_2气化反应。     

添加煤灰及混合氧化物对石油焦CO2高温气化反应的影响

以化学组成相近的燃烧煤灰、气化煤灰和混合氧化物为添加剂,分别通过干混法和湿混法加入石油焦中,并借助热重分析仪在1200-1400 ℃下进行CO₂气化实验,研究高温下煤灰掺混方式、含量及物相组成对石油焦CO₂气化的影响,并使用混合氧化物替代实际煤灰研究其对石油焦的高温气化催化作用。结果表明,石油焦气化反应速率随煤灰添加量的增加而提升;气化温度为1200、1300 ℃时,使用干混法和气化煤灰对石油焦的气化促进作用较弱;但气化温度为1400 ℃时,改变煤灰和石油焦的掺混方式及其中活性金属存在方式,对石油焦气化反应几乎没有影响。这是高温下煤灰熔融,导致液态熔体与石油焦表面接触良好、活性金属自由度高以及传质阻力增加共同作用的结果。此时混合氧化物的催化指数与混合物中铁钙含量具有线性关系,即添加高铁钙含量的煤灰可以促进石油焦CO₂气化反应。     

煤的高温灰在加热过程中的行为研究

本文选用两种不同成份的高温灰,对煤灰的加热行为和熔融性质进行试验研究。结果表明,在氧化气氛中,在高温作用下,灰中无机组份彼此之间要发生复杂反应和相变转移。1200℃时煤灰内矿物只有石英、斜长石、赤铁矿和莫来石存在。在还原气氛条件下,煤灰在低于灰熔点温度前已形成大量液相。本文对不同温度下形成的煤灰矿物组成用X射线衍射分析和扫描电子显微镜,观察其物相变化趋势。     

水蒸气气化条件下碳酸钾对煤灰烧结和矿物质演化的影响

在水蒸气气化气氛（水蒸气-氢气-一氧化碳-二氧化碳混合气氛）下考察了反应压力对负载碳酸钾煤灰烧结温度的影响，建立了包含煤的灰分、煤灰化学组成、催化剂负载量及反应压力因素的煤灰烧结温度预测关系式，预测结果与实测烧结温度的误差在±15℃（2%）范围内。利用X射线衍射仪和FactSage热力学计算软件对不同气氛和压力下煤灰中的矿物组成及含量的变化规律进行了分析。结果表明，碳酸钾与煤灰中的硬石膏、方解石反应生成硫酸钾和碳酸钾钙；水蒸气气化气氛下硫酸钾和赤铁矿被还原，碳酸钾钙的分解温度随反应压力的增大而升高；负载催化剂煤灰中氢氧化钾的量随温度和压力的提高而增加，不同压力下煤灰的最低烧结温度与氢氧化钾的含量有关，当氢氧化钾的含量达到一定值时，不同压力下对应的温度与实验测得的煤灰烧结温度接近。     

高温气化条件下Na_2O对煤灰中矿物质演化行为的影响

利用XRD和FT-IR考察了高温弱还原气氛下Na_2O对两种硅铝含量不同的煤灰中矿物质组成的影响,揭示了Na_2O影响煤灰熔融特性的本质。通过Fact Sage计算了高温下矿物质反应的ΔG,探讨了Na_2O影响煤灰中矿物质组成的机理。结果表明,Na_2O对煤灰矿物质组成的影响与原煤灰的硅铝含量密切相关。硅铝总含量82.89%的煤灰,Na_2O含量为5%-20%时,钠长石和霞石的生成是煤灰熔融温度降低的主要原因;当Na_2O含量大于20%时,导致煤灰熔融温度降低的原因是霞石的生成。硅铝总含量47.85%的煤灰,Na_2O含量小于10%时,没有含钠矿物质生成;当Na_2O含量大于10%时,主要生成菱硅钙钠石、青金石和含钠的硅铝酸盐矿物,导致煤灰熔融温度降低。Fact Sage计算表明生成含Na矿物质反应的ΔG较小,其在高温下更容易发生。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.