Effect of the surface coverage of endcapped C18-silica on the excess adsorption isotherms of commonly used organic solvents from water in reversed phase liquid chromatography

The excess adsorption isotherms of methanol, ethanol, 2-propanol, acetonitrile, and tetrahydrofuran from water were measured on five different silica-based packing materials by the minor disturbance method. These materials were prepared with the same lot of 5-microm particles (average pore size 90 A), all endcapped with trimethylchlorosilane (TMS), and bonded to octadecyl chains with different surface coverages (0, 0.42, 1.01, 2.03, and 3.15 micromol/m2). The relative adsorption of one eluent by respect to a second one informs on the heterogeneity of the material (alkyl-bonded and bare silica regions) and on the accessibility of the unreacted silanol groups to the mobile phase. It is shown that the total surface area of the adsorbent decreases with increasing degree of surface coverage with octadecyl chains and that the relative surface area of the regions occupied by accessible silanol groups to the regions occupied by alkyl-bonded groups decreases. For the five columns, an average of 10% of the adsorbent surface area is covered of bare silica accessible to the liquid phase, with a minimum of 5% with tetrahydrofuran and a maximum of 12% with ethanol or 2-propanol. Increasing the surface coverage by the C18 chains causes a significant increase of the attraction potential of the hydrophobic surface toward the organic solvent. This result is confirmed by the increase of the number of adsorbate monolayers with increasing bonding density of the octadecyl chains. This number is twice larger for the 315C18 column than for the C1 column.     

Adsorption mechanism in reversed-phase liquid chromatography. Effect of the surface coverage of a monomeric C18-silica stationary phase

The effect of the bonding density of the octadecyl chains onto the same silica on the adsorption and retention properties of low molecular weight compounds (phenol, caffeine, and sodium 2-naphthalene sulfonate) was investigated. The same mobile phase (methanol:water, 20:80, v/v) and temperature (T = 298 K) were applied and two duplicate columns (A and B) from each batch of packing material (neat silica, simply endcapped or C1 phase, 0.42, 1.01, 2.03, and 3.15 micromol/m2 of C18 alkyl chains) were tested. Adsorption data of the three compounds were acquired by frontal analysis (FA) and the adsorption energy distributions (AEDs) were calculated using the expectation-maximization method. Results confirmed earlier findings in linear chromatography of a retention maximum at an intermediate bonding density. From a general point of view, the saturation capacity of the adsorbent tends to decrease with increasing bonding density, due to the vanishing space intercalated between the C18 bonded chains and to the decrease of the specific surface area of the stationary phase. The equilibrium constants are maximum for an intermediary bonding density (approximately 2 micromol/m2). An enthalpy-entropy compensation was found for the thermodynamic parameters of the isotherm data. Weak equilibrium constants (small deltaH) and high saturation capacities (large deltaS) were observed at low bonding densities, higher equilibrium constants and lower saturation capacities at high bonding densities, the combinations leading to similar apparent retention in RPLC. The use of a low surface coverage column is recommended for preparative purposes.     

Influence of the degree of coverage of C18-bonded stationary phases on the mass transfer mechanism and its kinetics

The influence of the degree of coverage of a silica surface with bonded C18 alkyl chains on the mass transfer mechanism in RPLC was investigated. Five packing materials were used, prepared with the same batch of silica particles (5 microm diameter, 90 A average pore size): one column was packed with the silica derivatized by trimethylchlorosilane (TMS) (C1, 3.92 micromol/m2), and the other four with the silica first derivatized with octadecyl-dimethyl-chlorosilane (C18, 0.42, 1.01, 2.03, and 3.15 micromol/m2), and then endcapped with TMS. A solution of methanol and water (25/75, v/v) was used as the mobile phase. The experimental HETP curves were acquired for each column by measuring the first moment and the second central moment of phenol and correcting them for the influence of the temperature increase due to the heat generated by the friction of the stream against the bed. The different kinetic parameters of the mass transfer in these packed chromatographic columns were identified (longitudinal diffusion, eddy diffusion, film mass transfer, and transparticle mass transfer) and quantified by fitting the experimental data to a new general HETP equation recently derived [F. Gritti, G. Guiochon, Anal. Chem., in press (AC-060203R).]. The agreement was excellent and allowed the comparison of the kinetic parameters among the six columns used. The highest column efficiency measured at conventional or fast flow rates (>0.5 ml/min) is obtained for the most retentive column, which has a surface coverage of 2.03 micromol/m2. The smallest HETP measured is as low as 10 microm, only twice the average particle diameter dp, due to the large contribution of surface diffusion (90%) to the particle effective diffusivity. However, no significant difference was observed between the efficiencies of the columns packed with C1 and C18 derivatized silica.     

Limits of the numerical estimation of the adsorption energy distribution from adsorption isotherm data using the expectation-maximization method

The limits of the use of the expectation-maximization (EM) method for the study of the heterogeneity of adsorbent surfaces were tested by calculating the adsorption energy distribution of systems having known degrees of heterogeneity. Connecting on-line two different columns allows the simulation of a heterogeneous system. The two columns used were endcapped, C(18)-bonded silica used as stationary phases and having different degrees of C(18) chain coverages (0.42 and 2.03 micromol/m(2)). The adsorption constants of phenol measured by frontal analysis (FA) are significantly different on these two columns. On each column, the adsorption behavior was best accounted for by a bi-Langmuir isotherm model, corresponding to a heterogeneous surface with a bimodal energy distribution. The difference between the adsorption energies on the weak adsorption sites of the two columns is 1.5 kJ/mol. The energy difference of their high energy sites is 2.2 kJ/mol. The EM method can readily distinguish between adsorption sites having energies that differ by more than 5 kJ/mol after more than 10 million iterations, but it cannot distinguish between adsorption sites for which this energy difference is less than 2 kJ/mol, even after 100 million iterations. For highly heterogeneous systems, (e.g., those with more than three different types of adsorption sites), the EM program does not converge necessarily towards the actual energy distribution function but toward a simpler one, having fewer adsorption sites that are almost equally spaced in the energy space. This failure of the EM program is related to the fact that, despite the excellent precision of the FA measurements (<1%), any series of adsorption data can be represented by several distinct AEDs. Thus, the degree of heterogeneity of RPLC adsorbents determined with the EM method might often be minimized, resulting in erroneous values of the isotherm parameters.     

Experimental evidence of the influence of the surface chemistry of the packing material on the column pressure drop in reverse-phase liquid chromatography

The permeabilities of six columns packed with different packing materials (neat silica, C(1) endcapped silica at 3.92 micro mol/m(2), C(18) bonded and endcapped silica with 0.42, 1.01, 2.03, and 3.15 micro mol/m(2) of C(18) bonded chains) were measured. All these materials derive from the same batch of spherical particles, 5 micro m in diameter. The columns have the same tube inner diameter (phi=0.460+/-0.003 cm) and length (L=15.000+/-0.003 cm). The experimental conditions were the same, flow-rate (F(v)=1.000+/-0.003 mL/min) and temperature (295 K). Nevertheless, it was found that the column permeability decreases significantly, by about 25%, from the neat silica column to the one packed with the highest density of C(18)-bonded silica (3.15 micro mol/m(2)). The results measured on two duplicate columns were very reproducible. Accurate (+/-0.5 %) measurements of the hold-volumes with concentrated and dilute solutions of NO(3)(-) showed that the columns had all nearly the same external porosity. The result cannot be explained by the error made on the volume of the column tube either as it was measured accurately for all the columns. The residual explanation is that the interstitial velocity distribution between the packed particles depends on the chemical nature of the external surface of these particles.     

Adsorption of organic matter at mineral/water interfaces. IV. Adsorption of humic substances at boehmite/water interfaces and impact on boehmite dissolution

The adsorption of Suwannee River fulvic acid (SRFA) and Pahokee peat humic acid (PPHA) at the boehmite (gamma-AlOOH)/water interface and the impact of SRFA on boehmite dissolution have been examined over a wide range of solution pH conditions (pH 2-12), SRFA surface coverages (Gamma(SRFA), total SRFA binding site concentration normalized by the boehmite surface area) of 0.0-5.33 micromol m(-2), and PPHA surface coverages (Gamma(PPHA), PPHA binding site concentration normalized by boehmite surface area) of 0.0-4.0 micromol m(-2), using macroscopic adsorption and in situ attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy. At relatively high SRFA surface coverages (Gamma(SRFA) = 5.33 micromol m(-2)), in situ ATR-FTIR spectral features of adsorbed SRFA are very similar to those measured for SRFA in solution at approximately 1-3 pH units higher. At sub-monolayer surface coverages (Gamma(SRFA) = 1.20 and 2.20 micromol m(-2)), several new peaks and enhancements of the intensities of a number of existing peaks are observed. The latter spectral changes arise from several nonorganic extrinsic species (i.e., adsorbed carbonate and water, for alkaline solution conditions), partially protonated SRFA carboxyl functional groups (near-neutral pH conditions), and small quantities of inner-spherically adsorbed SRFA carboxyl groups and/or Al(III)-SRFA complexes (for acidic conditions). The spectra of PPHA adsorbed at boehmite/water interfaces also showed changes generally consistent with our observations for SRFA sorbed on boehmite. These observations confirm that SRFA and PPHA are predominantly adsorbed at the boehmite/water interface in an outer-sphere fashion, with minor inner-sphere adsorption complexes being formed only under quite acidic conditions. They also suggest that the positively charged boehmite/water interface stabilizes SRFA and PPHA carboxyl functional groups against protonation at lower pH. Measurements of the concentration of dissolved Al(III) ions in the absence and presence of SRFA showed that the boehmite dissolution process is clearly inhibited by the adsorption of SRFA, which is consistent with previous observations that outer-spherically adsorbed organic anions inhibit Al-(oxyhydr)oxide dissolution.     

A chromatographic estimate of the degree of surface heterogeneity of RPLC packing materials. III. Endcapped amido-embedded reversed phase

The difference in adsorption behavior between a conventional monomeric endcapped C18 stationary phase (3.43 micromol/m2) and an endcapped polymeric RP-Amide phase (3.31 micromol/m2) was investigated. The adsorption isotherms of four compounds (phenol, caffeine, sodium 2-naphthalene sulfonate, and propranololium chloride) were measured by frontal analysis (FA) and the degree of heterogeneity of each phase for each solute was characterized by their adsorption energy distributions (AED), derived using the Expectation-Maximization method. The results show that only certain analytes (phenol and 2-naphthalene sulfonate) are sensitive to the presence of the polar embedded amide groups within the RP phase. Their binding constants on the amide-bonded phase are significantly higher than on conventional RPLC phases. Furthermore, an additional type of adsorption sites was observed for these two compounds. However, these sites having a low density, their presence does not affect much the retention factors of the two analytes. On the other hand, the adsorption behavior of the other two analytes (caffeine and propranololium chloride) is almost unaffected by the presence of the amide group in the bonded layer. Strong selective interactions may explain these observations. For example, hydrogen-bond interactions between an analyte (e.g., phenol or naphthalene sulfonate) and the carbonyl group (acceptor) or the nitrogen (donor) of the amido-embedded group may take place. No such interactions may take place with either caffeine or the cation propranololium chloride. This study confirms the hypothesis that analytes have ready access to locations deep inside the bonded layer, where the amide groups are present.     

Reducing residual silanol interactions in reversed-phase liquid chromatography. Thermal treatment of silica before derivatization

This study describes the thermal pretreatment of a silica gel between 150 and 800 degrees C before derivatization with dimethyloctadecylchlorosilane as a means of reducing residual silanol activity in HPLC bonded stationary phases. A time study was done from 12 to 48 h to find the optimum time needed for dehydroxylation. With increasing pretreatment temperatures, the number of reactive silanols is reduced from 8 micromol/m2 to essentially zero at 1000 degrees C (where sintering occurs). The effects of the thermal pretreatments were observed with diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and solid state cross polarization magic angle spinning (CP-MAS) 29Si NMR. Following derivatization, residual silanol activity and pH stability were tested by packing columns with the derivatized silica and carrying out a series of reversed-phase liquid chromatography (RPLC) experiments. Residual silanol activity was greatly reduced when the silica was pretreated at 800 degrees C, leading to less peak tailing for basic solutes. In a strongly basic mobile phase (pH 11.5) the pretreated silica was surprisingly stable, although bond cleavage of C18 groups from the surface was observed.     

Influence of stationary phase solvation on shape selectivity and retention in reversed-phase liquid chromatography

In the past few decades, shape selectivity has drawn a great deal of attention from chromatographers. The chemistry and characteristics of bonded stationary phases such as phase type, length of bonded phase, surface coverage, and silica surface material have an effect on the shape selectivity of the columns. Although the effects of bonded phase shape selectivity are relatively well understood, one remaining question is the effect of intercalated solvent on shape selectivity. The intercalation of organic modifier and water molecules into the stationary phase is believed to introduce more rigidity into bonded alkyl chains in RPLC. The use of gas chromatography (GC) opens a new dimension to approach this question. C18 columns 4 cm in length were prepared in our laboratory and used in both LC and GC experiments. Shape selectivity and thermodynamic constants for the transfer of a solute from the mobile phase to the stationary phase have been determined as a function of monomeric octadecyl stationary phase bonding densities over the range of 1.44-3.43 micromol/m2 and a polymeric phase (nominal surface coverage 4.77 micromol/m2). Comparing LC and GC experiments, we observed: (a) similar relationships between shape and phenyl selectivities with monomerically bonded C18 phase densities; (b) different correlation of thermodynamic quantities (DeltaH degrees , DeltaS degrees , and DeltaG degrees ) versus bonded phase densities. The effects of high temperature and residual silanol groups are sources of difficulty in elucidation of the intercalated mobile phase role in selectivity and retention for GC measurements.     

Effects of the thermal heterogeneity of the column on chromatographic results

The influence of the thermal heterogeneity of HPLC columns on retention data was investigated. The retention factor of the retained compound phenol was measured at 24 increasing values of the flow rate, from 0.025 to 4.9 mL/min, on six different packing materials prepared with the same batch of silica particles (5 microm diameter, 90 A pore size). One column was packed with the neat silica particles, another with the silica endcapped with trimethylchlorosilane (TMS)(C(1), 3.92 micromol/m(2)), and the other four with silica first derivatized with octadecyl-dimethyl-chlorosilane (C(18), 0.42, 1.01, 2.03, and 3.15 micromol/m(2)), and second endcapped with TMS. Four different sources of heat contributing to raise the column temperature were considered: (1) the heat supplied by the hot high-pressure pump chamber to the solvent; (2) the adiabatic (dS=0) compression of the solvent in the high-pressure pump; (3) the isenthalpic (dH=0) decompression of the solvent during its migration along the porous chromatographic bed; and (4) the heat released by the friction of the solvent percolating through the column bed. The main contributions appear to be the heat supplied to the solvent by the HP pump and the friction heat. The average column temperature (ACT) was indirectly derived from the measurements of the first moment, mu(1), of phenol peak, of the column pressure drop, DeltaP, and of the retention factors of the phenol peak apices as a function of the flow rate applied. If the column is placed in a still-air bath at 298 K (and its temperature is not externally controlled), a longitudinal temperature gradient is established along the column and the average column temperature is about 6 K higher when this column is operated at 4.9 mL/min than when the flow rate is only 0.025 mL/min. If the column is placed in a heated air bath (temperature controlled at 316 or 338 K), the ACT changes by less than 3 K over the whole flow rate range applied.     

Physical origin of peak tailing on C18-bonded silica in reversed-phase liquid chromatography

Single component isotherm data of caffeine and phenol were acquired on two different stationary phases for RPLC, using a methanol/water solution (25%, v/v, methanol) as the mobile phase. The columns were the non-endcapped Waters Resolve-C18, and the Waters XTerra MS C18. Both columns exhibit similar C18 -chain densities (2.45 and 2.50 micromol/m2) and differ essentially by the nature of the underivatized solid support (a conventional, highly polar silica made from water glass, hence containing metal impurities, versus a silica-methylsilane hybrid surface with a lower density of less acidic free silanols). Thirty-two adsorption data points were acquired by FA, for caffeine, between 10(-3) and 24 g/l, a dynamic range of 24,000. Twenty-eigth adsorption data points were acquired for phenol, from 0.025 to 75 g/l, a dynamic range of 3000. The expectation-maximization procedure was used to derive the affinity energy distribution (AED) from the raw FA data points, assuming a local Langmuir isotherm. For caffeine, the AEDs converge to a bimodal and a quadrimodal distribution on XTerra MS-C18 and Resolve-C18, respectively. The values of the saturation capacity (q(s,1) approximately equal to 0.80 mol/l and q(s,2) approximately equal to 0.10 mol/l) and the adsorption constant (b1 approximately equal to 3.11/mol and b2 approximately equal to 29.1 l/mol) measured on the two columns for the lowest two energy modes 1 and 2, are comparable. These data are consistent with those previously measured on an endcapped Kromasil-C18 in a 30/70 (v/v), methanol/water solution (q(s,1) = 0.9 mol/l and q(s,2) = 0.10 mol/l, b1 = 2.4 l/mol and b2 = 16.1 l/mol). The presence of two higher energy modes on the Waters Resolve-C18 column (q(s,3) approximately equal to 0.013 mol/l and q(s,4) approximately equal to 2.6 10(-4) mol/l, b3 approximately equal to 252 l/mol and b4 = 13,200 l/mol) and the strong peak tailing of caffeine are explained by the existence of adsorption sites buried inside the C18-bonded layer. It is demonstrated that strong interactions between caffeine and the water protected bare silica surface cannot explain these high-energy sites because the retention of caffeine on an underivatized Resolve silica column is almost zero. Possible hydrogen-bond interactions between caffeine and the non-protected isolated silanol groups remaining after synthesis amidst the C18-chain network cannot explain these high energy interactions because, then, the smaller phenol molecule should exhibit similarly strong interactions with these isolated silanols on the same Resolve-C18 column and, yet, the consequences of such interactions are not observed. These sites are more consistent with the heterogeneity of the local structure of the C18-bonded layer. Regarding the adsorption of phenol, no matter whether the column is endcapped or not, its molecular interactions with the bare silica were negligible. For both columns, the best adsorption isotherm was the Bilangmuir model (with q(s,1) approximately equal to 2 and q(s,2) approximately equal to 0.67 mol/l, b1 0.61 and b2 approximately equal to 10.3 l/mol). These parameters are consistent with those measured previously on an endcapped Kromasil-C18 column under the same conditions (q(s,1) = 1.5 and q(s,2) = 0.71 mol/l, b1 = 1.4 l/mol and b2 = 11.3 l/mol). As for caffeine, the high-energy sites are definitely located within the C18-bonded layer, not on the bare surface of the adsorbent.     

Tris(2-methyl-8-quinolinolato)gallium(III) as a fluorescent probe for sensitive silanol-testing.

The peak shape of tris(2-methyl-8-quinolinolato)gallium(III) by reversed-phase high-performance liquid chromatography was found to be very sensitive to trace amounts of silanol groups on the surface of octadecylsylanized silica gel (ODS silica gel). The variation of the peak of the gallium(III) complex can be used as a probe of the residual silanol groups in an ODS column. The chromatographic peak parameters of the complex were compared with the silanol activities output by some silanol-detecting tests using nitrogen-containing compounds as probes. The comparison was performed with several commercially available ODS columns and laboratory-packed columns in which the amount of silanol groups was controlled by mixing fully endcapped ODS materials and a non-endcapped ODS material. The peak height was the most effective parameter among the peak parameters, and much more sensitive than the silanol-detecting tests using nitrogen-containing compounds, in detecting a trace amount of silanol groups that could not be detected by other silanol-detecting tests.     

Effect of long-term storage and use on the properties of reversed-phase liquid chromatographic columns

In order to study column deterioration as a result of long-term storage and/or usage in liquid chromatography analyses, 55 pairs (same batch) of different commercial reversed-phase C(18) columns were examined using an already existing column characterisation system. After initial testing, one column was stored and the other was used to analyse different pharmaceuticals. All columns were characterized by four chromatographic parameters reflecting hydrophobicity, silanol activity, metal impurity and steric selectivity at the beginning and at the end of the test. An F-value was calculated to express the change of column properties with one single number. After performing analyses, higher F-values were obtained as compared to the non-used, stored columns. Although the time during which the columns were used to perform analyses was relatively short, an obvious influence was noticed, mainly resulting from small changes in silanol activity and hydrophobicity. Most of the affected columns have no endcapping and/or no base deactivation, making them more vulnerable for degradation, resulting in higher silanol activity and faster ageing. This effect is observed less with columns equipped with polar-embedded groups and/or polar endcapping, protecting the column by blocking the silanol groups and attracting a shielding water layer. Also columns with higher coverages and bulky or long chains show more resistance towards degradation.     

Physisorbed water layer formation on fully hydroxylated mesoporous silicas

Kinetic adsorption isotherms were obtained by gravimetric determination of water adsorption into fully hydroxylated mesoporous silicas using samples exposed to controlled humidity air at 22+/-2 degrees C. Twenty kinetic isotherms at several relative humidities (11, 33, 43, 51, 75, and 85%) were obtained with 11 different batches of silica using this simple procedure to obtain quantitative information on the formation of H2O adsorbates. The H2O surface concentrations obtained from the plateau data of individual kinetic adsorption isotherms at 43 and 51% RH, typically precise to about +/-1%, show that a complete monolayer is formed with negligible second-layer adsorption at these relative humidities. This monolayer has a surface concentration of 7.68+/-0.30 micromol H2O/m2, which is lower than the quasi-equilibrium concentration at these relative humidities obtained by the conventional equilibrium-isotherm procedure. Comparison with the Kiselev-Zhuravlev concentration of silanol groups on fully hydroxylated silicas (7.6+/-0.8 micromol SiOH/m2) confirms 1:1 H2O:SiOH stoichiometry of this monolayer. The presence of partial-layer structures at 2.85+/-0.1 and 5.7+/-0.1 micromol H2O/m2 is suggested by isotherms at 11 and 33% RH, respectively, while a bilayer at approximately 14+/-1 micromol H2O/m2 is suggested by kinetic isotherms at 75 and 85% RH.     

Effect of high pH column regeneration on the separation performances in reversed phase chromatography of peptides

Caustic regeneration procedures are often used in chromatographic purification processes of peptides and proteins to remove irreversibly bound impurities from the stationary phase. Silica-based materials are the most commonly used materials in reversed phase chromatography of peptides. Their limited chemical stability at high pH can be, however, problematic when high pH column regeneration (i.e. cleaning in place) is required. The effect of cleaning in place on the surface chemistry of the stationary phase has been investigated using the Tanaka test. It has been shown that the high pH treatment does not significantly affect the hydrophobicity of the material, but it strongly increases its silanol activity. A representative peptide purification process has been used to investigate the impact of cleaning in place on the separation performance. It has been shown that the caustic regeneration increases the peptide retention at high pH (pH 6.5), due to the interactions between the peptide and the negatively charged silanol groups. These unwanted interactions reduce the separation performances by decreasing the selectivity between the late eluting impurities and the main peptide. However, it has been shown that the effect of the silanol groups on the peptide adsorption and on the separation performance can be minimized by carrying out the purification process at low pH (pH ∼ 2). In this case, the silanol groups are protonated and their electrostatic interactions with the positively charged analyte (i.e. peptides) are suppressed. In these conditions, the peptide adsorption and the impurity selectivity is not changing upon high pH column regeneration and the separation performance is not affected.     

Proton-arsenic adsorption ratios and zeta potential measurements: implications for protonation of hydroxyls on the goethite surface

Successfully modeling the surface charge of goethite and anion adsorption on goethite using a surface complexation model (SCM) alone cannot verify the assumptions of this model. In this study, the assumptions of 2-pK triple layer model (TLM) and two-site 1-pK basic stern model (BSM) were assessed with respect to their ability to interpret both the proton-anion adsorption ratios of dimethylarsinate (DMA), monomethylarsonate (MMA), and arsenate and their effect on the zeta-potential. The proton-DMA adsorption ratio is around 0.9 at pH 4.25 and 1.1 at pH 6.75 at DMA surface coverage ranging from 0 to 2 micromol m(-2), and the zeta-potential is independent of DMA adsorption at these two pH values. The proton-MMA adsorption ratio increases to 1.5 at pH 4 and 2.1 at pH 6.75 as the MMA surface coverage decreases to 0.5 micromol m(-2). The zeta-potential is less dependent on MMA adsorption at a surface coverage range of 0 to 1.8 micromol m(-2), and it then decreases with a further increase in the MMA surface coverage at pH 4 and 6.75. The proton-arsenate adsorption ratio decreases to 2 as the arsenate surface coverage approaches zero, and the zeta-potential decreases linearly with the increasing arsenate surface coverage at pH 4 and 6.75. Neither the 2-pK TLM nor the 1-pK BSM give a consistent interpretation of both the proton-arsenic adsorption ratio and the effect of arsenic on the zeta-potential. The results suggest that the 1-pK MUSIC model in which each type of surface hydroxyls has its own intrinsic proton-affinity constant and only one type of surface hydroxyls is involved in DMA, MMA, and arsenate adsorption is preferably pursued. The protonation degree of reactive hydroxyls estimated from proton-arsenic adsorption ratios is 0.2 at pH 4 and 0 at pH 6.75 in 0.001 M NaNO(3).     

Influence of the pressure on the properties of chromatographic columns .III. retention volume of thiourea, hold-up volume, and compressibility of the C18-bonded layer

The influence of the average column pressure (ACP) on the elution volume of thiourea was measured on two RPLC columns, packed with Resolve-C18 (surface coverage 2.45 micromol/m2) and Symmetry-C18 (surface coverage 3.18 micromol/m2), and it was compared to that measured under the same conditions on an underivatized silica (Resolve). Five different methanol-water mixtures (20, 40, 60, 80 and 100% methanol, v/v) were used. Once corrected for the compressibility of the mobile phase, the data show that the elution volume of thiourea increases between 3 and 7% on the C18-bonded columns when the ACP increases from 50 to 350 bar, depending on the methanol content of the eluent. No such increase is observed on the underivatized Resolve silica column. This increase is too large to be ascribed to the compressibility of the stationary phase (silica + C18 bonded chains) which accounts for less than 5% of the variation of the retention factor. It is shown that the reason for this effect is of thermodynamic origin, the difference between the partial molar volume of the solute in the stationary and the mobile phase, Delta V, controlling the retention volume of thiourea. While Delta V is nearly constant for all mobile phase compositions on Resolve silica (with Delta V approximately equal to -4 mL/mol), on RPLC phases, it significantly increases with increasing methanol content, particularly above 60% methanol. It varies between -5 mL/mol and -17 mL/mol on Resolve-C18 and between -9 mL/mol and -25 mL/mol on Symmetry-C18. The difference in surface coverage between these two RP-HPLC stationary phases increases the values of Delta V by about 5 mL/mol.     

Effect of the endcapping of reversed-phase high-performance liquid chromatography adsorbents on the adsorption isotherm

The retention mechanisms of n-propylbenzoate, 4-t ert-butylphenol, and caffeine on the endcapped Symmetry-C(18) and the non-endcapped Resolve-C(18) are compared. The adsorption isotherms were measured by frontal analysis (FA), using as the mobile phase mixtures of methanol or acetonitrile and water of various compositions. The isotherm data were modeled and the adsorption energy distributions calculated. The surface heterogeneity increases faster with decreasing methanol concentration on the non-endcapped than on the endcapped adsorbent. For instance, for methanol concentrations exceeding 30% (v/v), the adsorption of caffeine is accounted for by assuming three and two different types of adsorption sites on Resolve-C(18) and Symmetry-C(18), respectively. This is explained by the effect of the mobile phase composition on the structure of the C(18)-bonded layer. The bare surface of bonded silica appears more accessible to solute molecules at high water contents in the mobile phase. On the other hand, replacing methanol by a stronger organic modifier like acetonitrile dampens the differences between non-endcapped and endcapped stationary phase and decreases the degree of surface heterogeneity of the adsorbent. For instance, at acetonitrile concentrations exceeding 20%, the surface appears nearly homogeneous for the adsorption of caffeine.     

Comparison of the chromatography of octadecyl silane bonded silica and polybutadiene-coated zirconia phases based on a diverse set of cationic drugs

In this study, we compare the separation of basic drugs on several octadecyl silane bonded silica (ODS) phases and a polybutadiene-coated zirconia (PBD-ZrO2) phase. The retention characteristics were investigated in detail using a variety of cationic drugs as probe solutes. The ODS phases were selected to cover a relatively wide range in silanol activity and were studied with ammonium phosphate eluents at pH 3.0 and 6.0. Compared to any of the ODS phases, the PBD-ZrO2 phase showed very significant differences in selectivities towards these drugs. Due to the presence of both reversed-phase and ion-exchange interactions between the stationary phase and the basic analyte on ODS and PBD-ZrO2, mixed-mode retention takes place to some extent on both types of phases. However, very large differences in the relative contributions from ion-exchange and reversed-phase interactions on the two types of phases led to quite different selectivities. When phosphate is present in the eluent and adsorbs on the surface, the PBD-ZrO2 phase takes on a high negative charge over a wide pH range due to phosphate adsorption on its surface. On ODS phases, ion-exchange interactions result from the interactions between protonated basic compounds and ionized residual silanol groups. Since the pH of the eluent influences the charge state of the silanol groups, the ion-exchange interactions vary in strength depending on pH. At pH 6.0, the ion-exchange interactions are strong. However, at pH 3.0 the ion-exchange interactions on ODS are significantly smaller because the silanol groups are less dissociated at the lower pH. Thus, not only are the selectivities of the ODS and PBD-ZrO2 phases different but quite different trends in retention are observed on these two types of phases as the pH of the eluent is varied. More importantly, by using the large set of "real" basic analytes we show the extreme complexity of the chromatographic processes on the reversed stationary phases. Both the test condition and solute property influence the column performance. Therefore, use of only one or two probe solutes is not sufficient for column ranking.