Determination of Malathion Using Corona Discharge – Ion Mobility Spectrometry with Solid-Phase Microextraction

A corona discharge (CD) ion mobility spectrometer combined with solid-phase microextraction was constructed. The detection limit and stability of the system for malathion detection were improved using a novel sample introduction port through which the sample desorption was performed in high-temperature drift tube and the sample was introduced directly to the ionization area. The working parameters of the distance between CD needle tip and carrier gas outlet, the drift tube and carrier gas temperature, the carrier gas flow, and the voltage on CD needle were selected. When the extraction time for standard malathion was set to 5?min, the detection limit was 0.96?µg?L^?1 based on thrice the baseline noise, the linear range was 50–500?µg?L^?1, the correlation coefficient was approximately 0.9941, and the relative standard deviation was below 10%. Malathion-spiked lake water samples were analyzed using the developed system and the recovery was 92–102%. This method is suitable for the rapid detection of organophosphorus pesticide residues.     

A Polypyrrole-Based Sorptive Microextraction Coating for Preconcentration of Malathion from Aquatic Media

A new micro-solid phase extraction method was developed by combining solid-phase extraction and stir bar sorptive extraction to benefit from the advantages of both techniques. A polypyrrole coating was electrochemically synthesized on the surface of an already used graphite furnace, employed in electro-thermal atomic absorption spectroscopy. The cylindrical geometry of the graphite tube provided a rather huge surface area, suitable for sorptive extraction. The novel sorbent coating was examined as an extracting medium to isolate malathion. Effects of different parameters such as extraction time, salt concentration, sample volume, desorption solvent and time were investigated and optimized. Under the optimized conditions, the limit of detection and limit of quantification of the developed method were 5 and 20?ng?L^?1, respectively. The calibration curve showed linearity in the range of 0.1?C100???g?L^?1 (R ²?=?0.9968). The precision was evaluated at 0.1 and 1???g?L^?1 concentration levels and relative standard deviations (n?=?3) were found to be 10 and 7%, respectively. The developed method was successfully applied to the extraction of malathion from real river water and tap water samples, and relative recoveries at the spiked level of 0.1???g?L^?1 were 94 and 97%, respectively.     

Ultraviolet photolytic vapor generation from particulate ensembles for detection of malathion residues in aerosols

A method to selectively generate vapor signatures from malathion entrained within matrices of surface-impacted aerosol particles has been demonstrated. The method uses ultraviolet radiation (172 or 222 nm) from a continuous wave discharge lamp to photodissociate malathion molecules collected within and on surface-impacted particles, followed by detection via ion mobility spectrometry (IMS). Since surface heating does not occur, only those molecules whose photofragments exhibit high vapor pressure are introduced into the IMS instrument and then only those exhibiting high proton affinity are subsequently detected. This process produces less signal clutter than in pyrolysis-IMS, where the background aerosol is pyrolyzed along with the sample. Quantities of malathion as small as 50 ng could be detected when the malathion was entrained on a clean surface, and as small as 100 ng when co-entrained on a surface with much larger quantities of background aerosols such as diesel soot, road dust, Bacillus globigii, albumin, and cotton lint. This sensitivity indicates that, when combined with a particle collector as an effective pre-concentrator, detection of malathion aerosol concentrations of <0.01 mg/m³ will be possible. Since malathion can be viewed as a model compound, this technique is also extendable to the detection of organophosphate war chemicals.     

Analysis of Malathion pesticide residues in rice samples using ultrasound-assisted emulsification-microextraction coupled to UV photoionization source ion mobility spectrometry

The present paper describes the validation of ultrasound-assisted emulsification-microextraction method followed by ion mobility spectrometry (IMS) for determination malathion pesticides. Ultrasound radiation was applied for accelerating the emulsification of microliter organic solvent in aqueous solutions and enhancing the microextraction efficiency. This preconcentration step combined with IMS detection provided a precise and accurate method for determination of trace amounts of malathion pesticides. The effect of parameters influencing the extraction efficiency such as sonication time, type of extraction solvent, extraction solvent volume, and salt concentration were investigated and discussed. Under the optimum conditions, enrichment factors was 270 with corresponding LOD of 4 μg/L. Linearity with a coefficient of estimation (r²) were >0.99 in the concentration level range of 6–750 μg/L for extraction of Malathion in water samples. The applicability of the proposed method was evaluated by determination of the residues of the investigated pesticide in rice paddy water gathered from four stations during 60 days after spraying (June 2014), and in storage rice samples in Mazandaran province, Iran.     

Determination of carbamazepine in formulation samples using dispersive liquid–liquid microextraction method followed by ion mobility spectrometry

A simple, sensitive, fast and efficient method based on dispersive liquid–liquid microextraction (DLLME) followed by ion mobility spectrometry (IMS) has been proposed for preconcentration and trace detection of carbamazepine (CBZ) in formulation samples. In this method, 1 mL of methanol (disperser solvent) containing 80 μL of chloroform (extraction solvent) was rapidly injected by a syringe into a sample. After 5 min centrifugation, the preconcentrated carbamazepine in the organic phase was determined by IMS. Development of DLLME procedure includes optimization of parameters influencing the extraction efficiencies such as kind and volume of extraction solvent, disperser solvent and salt addition, centrifugation time and pH of the sample solution. The proposed method presented good linearity in the range of 0.05–10 μg mL^?1 and the detection limit was 0.025 μg mL^?1. The repeatability of the method expressed as relative standard deviation was 6 % (n = 5). This method has been applied to the analysis of carbamazepine formulation samples with satisfactory relative recoveries ≤75 %.     

Application of the molecularly imprinted solid-phase extraction to the organophosphate residues determination in strawberries

This study describe an analytical method employing gas chromatography (GC) using flame photometric detection that has been developed for the simultaneous determination of organophosphate pesticides (diazinon, disulfoton, parathion, chlorpyrifos and malathion) in strawberry samples. For this purpose, molecularly imprinted solid-phase extraction was applied as a sample preparation technique. The method was linear in the ranges from 0.10 to 1.00?μg?g^?1, for diazinon, disulfoton, parathion and chlorpyrifos, and 0.10 to 2.00?μg?g^?1 for malathion with r?>?0.99. The detection limits (LD) ranged from 0.02 to 0.05?μg?g^?1. Recovery studies yielded average recoveries in the range of 65.25 to 87.70?%. These results showed the potential of this technique for organophosphate residue monitoring in strawberry samples.     

Integrated explosive preconcentrator and electrochemical detection system for 2,4,6-trinitrotoluene (TNT) vapor

This article reports on an integrated explosive-preconcentration/electrochemical detection system for 2,4,6-trinitrotoluene (TNT) vapor. The challenges involved in such system integration are discussed. A hydrogel-coated screen-printed electrode is used for the detection of the thermally desorbed TNT from a preconcentration device using rapid square wave voltammetry. Optimization of the preconcentration system for desorption of TNT and subsequent electrochemical detection was conducted yielding a desorption temperature of 120 °C under a flow rate of 500 mL min⁻¹. Such conditions resulted in a characteristic electrochemical signal for TNT representing the multi-step reduction process. Quantitative measurements produced a linear signal dependence on TNT quantity exposed to the preconcentrator from 0.25 to 10 μg. Finally, the integrated device was successfully demonstrated using a sample of solid TNT located upstream of the preconcentrator.     

Solid phase micro-extraction coupled with ion mobility spectrometry for the analysis of ephedrine in urine

Quantitative solid phase micro-extraction (SPME) coupled with ion mobility spectrometry is demonstrated using the analysis of ephedrine in urine. Since its inception in the 1970's ion mobility spectrometry (IMS) has evolved into a useful technique for laboratories to detect explosives, chemical warfare agents, environment pollutants and, increasingly, for detecting drugs of abuse. Ephedrine is extracted directly from urine samples using SPME and the analyte on the fiber is heated by the IMS desorber unit and vaporized into the drift tube. The analytical procedure was optimized for fiber coating selection, extraction temperature, extraction time, sample pH, and analyte desorption temperature. The carryover effects, ion fragmentation characteristics, peak shapes, and drift times of ephedrine were also evaluated based on the direct interfacing of SPME to IMS. A limit of detection of 50 ng/mL of ephedrine in urine and a linear range of 3 orders of magnitude were obtained, showing that SPME-IMS compares well to other techniques for ephedrine and drug analysis presented in the literature.     

Determination of 26 polychlorinated biphenyls congeners in soil samples using microwave-assisted extraction with open vessel and gas chromatography

A procedure focused on microwave-assisted extraction in open vessel (MAE-OV) and gas chromatography with electron capture detection (GC-ECD) was used for the determination of 26 congeners of polychlorinated biphenyls (PCBs) in soil samples. The limit of detection (LOD) and limit of quantification (LOQ) were evaluated for commercial PCBs mixture Aroclor1260. LOD and LOQ were calculated for each PCB congener, in the ranges (0.03–0.27?ng?g^?1) and (0.11–0.70?ng?g^?1), respectively. After optimization, 26 PCBs congeners were successfully extracted from soil samples with recovery amounts ranging between 84.7% and 117.3% for all PCBs congeners. The evaluated method of MAE-OV showed good separation and extraction of all PCBs congeners from soil samples. Extraction parameters such as solvent choice, power and extraction time were investigated. This study indicated that MAE-OV could be an interesting alternative method to extract PCBs from soils, since it is economical, easy, fast and requires low amounts of solvents.     

Matrix solid-phase dispersion extraction of organophosphorous pesticides from beeswax

Beeswax is a complex mixture of lipophilic compounds and other components such as aliphatic alcohols and carotenoids. Then, extraction and clean-up for pesticide analysis in beeswax is a challenge. In this work, a multiresidue method for the analysis of dichlorvos (DCV), diazinon, malathion, methyl parathion and coumaphos (CMF) in beeswax was developed. The proposed approach is based on matrix solid-phase dispersion extraction. The adsorbent for sample clean-up was studied and a simplex-centroid cubic statistical design was applied to evaluate pure solvents and their binary and ternary mixtures to elute the analytes. Finally, Florisil and ethyl acetate were chosen as solid support and eluting solvent, respectively. After extraction, pesticides were separated and detected by gas chromatography/mass spectrometry. The method achieved acceptable recoveries (70–85%; except for DCV, 24–38%) with relative standard deviations below 5%. The repeatability of the method was lower than 8% and interday variability was below 12%. The limit of detection (LOD) for the analytes varies between 0.2 and 2.6 µg?kg^?1 and limit of quantification from 0.93 to 8.8 µg?kg^?1. LOD reached for CMF was below the maximum residue limit allowed by the legislation of the United States and Canada.     

Trace determination of malachite green in water samples using dispersive liquid–liquid microextraction coupled with high-performance liquid chromatography-diode array detection

A simple and reliable method has been developed for the rapid analysis of trace levels of malachite green from water samples using dispersive liquid–liquid microextraction and high-performance liquid chromatography-diode array detection. Factors relevant to the microextraction efficiency, such as the type and volume of extraction solvent, nature and volume of the disperser solvent, the effect of salt, sample solution temperature and the extraction time were investigated and optimised. Under the optimal conditions the linear dynamic range of malachite green was from 0.2 to 100.0?µg?L^?1 with a correlation coefficient of 0.9962. The detection limit and limit of quantification were 0.1?µg?L^?1 and 0.3?µg?L^?1, respectively. The relative standard deviation (RSD) was less than 2.6% (n?=?5) and the recoveries of malachite green (5.0?µg?L^?1) from water samples were in the range of 99.2?±?1.7%. Finally the proposed method was successfully applied for the analysis of malachite green from fish farming water samples.     

Microfabricated chemical preconcentrators for gas-phase microanalytical detection systems

The gas or vapor preconcentrator is an analytical device that significantly improves the detection limit of a microanalytical system by preconcentrating the analyte. The preconcentrator performs front-end sampling and preconcentration of analyte by collecting and concentrating analyte over a period of time. After the analyte-collection phase is complete, a heat pulse releases the analyte as a concentrated wave into the detector. Desirable features of the preconcentrator device include the capability of operating at high flow rates, thermal heating with short-time constants, and selective collection of the analyte(s) of interest. The preconcentrators presented in this review are used as a generic front-end modification to gas-phase microanalytical detection systems, such as gas chromatographs, mass spectrometers, ion-mobility spectrometers, and microelectromechanical system (MEMS)-based chemical sensors. The advantages of the detector in incorporating a preconcentrator device are enhanced sensitivity and improved selectivity. Target analytes concentrated by the preconcentrators described in this review include various organic compounds in gas or vapor phase, such as explosives 2,4,6-trinitrotouluene (TNT) and 1,3,5 trinitro-1,3,5-triazine (RDX), chemical agent dimethyl methylphosphonate (DMMP), a broad range of organic vapors, such as toluene, benzene, ethylene and acetone, and mixtures of these gas-phase organic compounds. We discuss examples of the current trends in microfabricated preconcentrator technology as well as several applications of microfabricated preconcentrators.     

Stochastic resonance algorithm applied to quantitative analysis for weak liquid chromatographic signal of pyrene in water samples

The phenomenon of stochastic resonance (SR), which was discovered in recent years, rendered an entirely new way for the detection of weak signals, and it has been widely studied in many different science fields. This phenomenon is manifest in nonlinear systems whereby a weak signal can be amplified when the noise, signal and nonlinear system attain the proper cooperation. The introduced algorithm was employed to detect pyrene in drinking water samples with solid-phase extraction–liquid chromatography. The weak chromatographic peak of the analyte was amplified significantly, and the profiles of the peaks were also satisfactory. The limit of detection and the limit of quantification were improved from 0.022?ng?mL^?1 and 0.08?ng?mL^?1 to 0.004?ng?mL^?1 and 0.01?ng?mL^?1, respectively. The results showed an excellent quantitative relationship between concentrations and chromatographic responses. It is expected that the SR will be an effective tool to detect weak chromatographic peaks quantitatively in trace analysis.     

用于水中有机磷农药检测的离子迁移率谱仪预富集进样方法

建立了检测水中有机磷农药的离子迁移率谱仪预富集进样方法。预富集器由表面覆盖有吸附薄膜的微热板、聚四氟乙烯电路板和管座组成,具有操作简单,无需有机溶剂,自加热,热容小,功耗低等优点。以马拉硫磷检测为例,分析了富集器解吸升温速率和离子迁移率谱仪半透膜温度对检测结果的影响。采用高温短时脉冲加热和低温维持加热相结合的解吸方式,既可形成较高的进样浓度脉冲,又可减少进入漂移管的杂质,有利于提高离子迁移率谱仪检测灵敏度。实验表明:采用所述预富集及两阶段加热解吸进样方法,对水中马拉硫磷的检出限为3.9μg/L,达到了国家标准对水中有机磷检测的要求。     

Immunomagnetic nanoparticle based quantitative PCR for rapid detection of Salmonella

We have developed a rapid and sensitive method for immunomagnetic separation (IMS) of Salmonella along with their real time detection via PCR. Silica-coated magnetic nanoparticles were functionalized with carboxy groups to which anti-Salmonella antibody raised against heat-inactivated whole cells of Salmonella were covalently attached. The immuno-captured target cells were detected in beverages like milk and lemon juice by multiplex PCR and real time PCR with a detection limit of 10⁴ cfu.mL^?1 and 10³ cfu.mL^?1, respectively. We demonstrate that IMS can be used for selective concentration of target bacteria from beverages for subsequent use in PCR detection. PCR also enables differentiation of Salmonella typhi and Salmonella paratyphi A using a set of four specific primers. In addition, IMS—PCR can be used as a screening tool in the food and beverage industry for the detection of Salmonella within 3–4 h which compares favorably to the time of several days that is needed in case of conventional detection based on culture and biochemical methods.

Determination of ochratoxin A in licorice root using inverse ion mobility spectrometry

Despite the recent, successful efforts to detect mycotoxins, new methods are still required to achieve higher sensitivity, more simplicity, higher speed, and higher accuracy at lower costs. This paper describes the determination of ochratoxin A (OTA) using corona discharge ion mobility spectrometry (IMS) in the licorice root. A quick screening and measuring method is proposed to be employed after cleaning up the extracted OTA by immunoaffinity columns. The ion mobility spectrometer is used in the inverse mode to better differentiate the OTA peak from the neighboring ones. After optimization of the experimental conditions such as corona voltage, injection port temperature, and IMS cell temperature, a limit of detection (LOD) of 0.010 ng is obtained. Furthermore, the calibration curve is found to be in the range of 0.01-1 ng with a correlation coefficient (R²) of 0.988. Licorice roots were analyzed for their OTA content to demonstrate the capability of the proposed method in the quantitative detection of OTA in real samples.     

Polypyrrole/montmorillonite nanocomposite as a new solid phase microextraction fiber combined with gas chromatography–corona discharge ion mobility spectrometry for the simultaneous determination of diazinon and fenthion organophosphorus pesticides

A novel solid phase microextraction (SPME) fiber was prepared and coupled with gas chromatography corona discharge ion mobility spectrometry (GC–CD–IMS) based on polypyrrole/montmorillonite nanocomposites for the simultaneous determination of diazinon and fenthion. The nanocomposite polymer was coated using a three-electrode electrochemical system and directly deposited on a Ni–Cr wire by applying a constant potential. The scanning electron microscopy images revealed that the new fiber exhibited a rather porous and homogenous surface. The thermal stability of the fabricated fiber was investigated by thermogravimetric analysis. The effects of different parameters influencing the extraction efficiency such as extraction temperature and time, salt addition, stirring rate, the amount of nanoclay, and desorption temperature were investigated and optimized. The method was exhaustively evaluated in terms of sensitivity, recovery, and reproducibility. The linearity ranges of 0.05–10 and 0.08–10 μg L⁻¹, and the detection limits of 0.020 and 0.035 μg L⁻¹ were obtained for diazinon and fenthion, respectively. The relative standard deviation values were calculated to be lower than 5% and 8% for intra-day and inter-day, respectively. Finally, the developed method was applied to determine the diazinon and fenthion (as model compounds) in cucumber, lettuce, apple, tap and river water samples. The satisfactory recoveries revealed the capability of the two-dimensional separation technique (retention time in GC and drift time in IMS) for the analysis of complex matrices extracted by SPME.     

Detection of microbial volatile organic compounds (MVOCs) by ion-mobility spectrometry

Traces of microbial volatile organic compounds (MVOCs) in air can indicate the presence of growth of moulds in the indoor environment. Ion-mobility spectrometry is a very promising method for detection of these MVOCs, because of its high sensitivity. For development of an in-situ method for detection of MVOCs, a portable ion-mobility spectrometer (IMS) was used and test gases of 14 MVOCs and their respective mixtures were investigated. IMS spectra were recorded as a function of concentration of MVOCs in air. Drift time and mobility of reactant ions formed in positive polarity mode were determined and correlated with the mass-to-charge ratio (m/z) of the MVOCs investigated. The estimated detection limit has a specific value for each MVOC and is in the range 3 to 96 μg m⁻³ (1 to 52 ppb_V). Indoor trials show that IMS can indicate hidden mould growth.     

Indirect determination of the pesticide dimethoxydithiophosphate in an FIA-AAS system with liquid-liquid back-extraction

A method has been developed for the determination of dimethoxydithiophosphate (DDTP) by liquid-liquid extraction in a flow-injection analysis (FIA) system with detection by atomic-absorption spectrometry (AAS). It is based on the formation of the Cu(DDTP)(2) complex and its extraction into chloroform, and back-extraction of the copper with an ammonia buffer (pH 10). The method uses small amounts of samples, avoids handling errors and is fast and highly reproducible. It features a detection limit of 0.39 ppm DDTP (2.45 x 10(-6)M in the organic phase) and a relative standard deviation of 1.6%. The method has been applied to the determination of the organophosphorus pesticide malathion in an agricultural formulation.     

Immunomagnetic nanoparticle-based sandwich chemiluminescence-ELISA for the enrichment and quantification of E. coli

Rapid methods for the quantification of Escherichia coli are required for the monitoring of faecal contamination in water to secure public health. The immunomagnetic separation (IMS) offers rapid enrichment and purification of bacteria in complex matrices and is compatible with immunoassays. By means of this technique, non-target cells and matrix components which might interfere with subsequent analytical methods are removed. We present the synthesis of magnetic nanoparticles (MNPs) and covalent coupling to antibodies against the enterobacterial common antigen (ECA) for use with IMS. Quantification was carried out with a chemiluminescence-based sandwich enzyme-linked immunosorbent assay (ELISA). Our anti-ECA-MNPs allow for a group-specific enrichment of bacterial cells, which can be combined with a species-specific analytical method. The particles were used along with commercially available magnetic columns for the selective enrichment of E. coli from 10-mL water samples. The volumetric enrichment factor was 9. For enriched samples, the limit of detection was reduced from 5.0?×?10⁶ cells·mL^-1 to 2.6?×?10⁵ cells·mL^-1. Using 200 µL anti-ECA-MNPs, we determined a recovery of 97?±?6% for a sample containing 10⁶ cells·mL^-1 and 89?±?2% for a sample containing 10⁷ cells·mL^-1. The overall time for cell enrichment and detection was 3 h 45 min.