Atmospheric‐pressure spin plasma jets processing of polymethylmethacrylate surface using experimental design methodology

Atmospheric‐pressure spin plasma jets (APSPJs) have been developed to induce surface modifications on polymethylmethacrylate (PMMA). In this study, an experimental design methodology was used to investigate the influence of process parameters [such as radio frequency (RF) power, processing gap, and number of treatment cycles] on the characteristics of PMMA surface treated by APSPJs. It was observed from the atomic force microscope (AFM) and scanning electron microscope (SEM) results that the surface morphology of PMMA treated by direct plasma is much rougher than that treated by remote plasma. The direct plasma used in APSPJs processing created a substantial amount of nanostructure grains. Moreover, the measured XPS results showed that the O/C ratios of the PMMA surface were substantially increased and subsequently water contact angle decreased on direct plasma treatment. This decrease is due to an increase of oxygen‐containing functional groups on the PMMA surface by the APSPJs processing. From the statistical analysis, the RF power and the processing gap were found to play a major role in enhancing the hydrophilic properties of PMMA surface. In contrast, the number of treatment cycles played only a secondary role in this case. Finally, in this study the APSPJs processing was demonstrated to be an effective method for surface modification of PMMA by controlling processing parameters during the treatment process. Copyright © 2009 John Wiley & Sons, Ltd.     

Wettability interpretation of oxygen plasma modified poly(methyl methacrylate)

Poly(methyl methacrylate) (PMMA) has been modified via a dc pulsed oxygen plasma for different treatment times. The modified surfaces were characterized by X-ray photoelectron spectroscopy (XPS), optical profilometer, zeta potential, and advancing contact angle measurements. The measured advancing contact angles of water decreased considerably as a function of discharge. Several oxygen-based functionalities (carbonyl, carboxyl, carbonate, etc.) were detected by XPS, while zeta potential measurements confirmed an increase in negative charge for the treated PMMA surface. Evaluating the correlation between the concentration of polar chemical species and zeta potential, we found that increase in surface hydrophilicity results from the coeffect due to incorporation of oxygen functional groups and creation of charge states. The electrical double layer (EDL) effect was also considered in contact angle interpretation by introducing an additional surface tension term into Young's equation. We also found that EDL contribution to the solid-liquid interfacial tension is negligible and can be safely ignored for the systems considered here.     

等离子体改性聚氯乙烯的TiO2光催化降解研究

聚氯乙烯(PVC)是一种通用型塑料,无论采用挤出、注射或浸渍等方法均有优异的成型性能,至今仍是大量使用的弹性体.……     

PMMA人工晶状体表面的CF4/O2等离子体修饰

为了改善聚甲基丙烯酸甲酯(PMMA)人工晶状体的生物相容性和透光性, 采用CF4/O2等离子体技术修饰其表面. 通过衰减全反射红外光谱(ATR-FTIR)、X射线光电子能谱(XPS)、静态接触角(CA)测定、扫描电子显微镜(SEM)、紫外-可见近红外光谱(UV-Vis)等方法进行表征, 结果表明, 经CF4/O2等离子体处理后, PMMA表面的含氟和含氧基团增加, 其表面的亲水性增强, 生物相容性改善, 紫外光的隔离效率增大. 因此, 通过CF4/O2等离子体修饰能够有效地改善PMMA人工晶状体的性质.     

Surface modification of polyester by oxygen‐ and nitrogen‐plasma treatment

In this paper, we present a study on the surface modification of polyethyleneterephthalate (PET) polymer by plasma treatment. The samples were treated by nitrogen and oxygen plasma for different time periods between 3 and 90 s. The plasma was created by a radio frequency (RF) generator. The gas pressure was fixed at 75 Pa and the discharge power was set to 200 W. The samples were treated in the glow region, where the electrons temperature was about 4 eV, the positive ions density was about 2 × 10¹⁵ m^?3, and the neutral atom density was about 4 × 10²¹ m^?3 for oxygen and 1 × 10²¹ m^?3 for nitrogen. The changes in surface morphology were observed by using atomic force microscopy (AFM). Surface wettability was determined by water contact angle measurements while the chemical composition of the surface was analyzed using XPS. The stability of functional groups on the polymer surface treated with plasma was monitored by XPS and wettability measurements in different time intervals. The oxygen‐plasma‐treated samples showed much more pronounced changes in the surface topography compared to those treated by nitrogen plasma. The contact angle of a water drop decreased from 75° for the untreated sample to 20° for oxygen and 25° for nitrogen‐plasma‐treated samples for 3 s. It kept decreasing with treatment time for both plasmas and reached about 10° for nitrogen plasma after 1 min of plasma treatment. For oxygen plasma, however, the contact angle kept decreasing even after a minute of plasma treatment and eventually fell below a few degrees. We found that the water contact angle increased linearly with the O/C ratio or N/C ratio in the case of oxygen or nitrogen plasma, respectively. Ageing effects of the plasma‐treated surface were more pronounced in the first 3 days; however, the surface hydrophilicity was rather stable later. Copyright © 2008 John Wiley & Sons, Ltd.     

Surface characterization of CuSn thin films deposited by RF co‐sputtering method

CuSn thin films were deposited by the radio‐frequency (RF) magnetron co‐sputtering method on Si(100) with Cu and Sn metal targets with various RF powers. The thickness of the films was fixed at 200 ± 10 nm. The synthesized CuSn thin films mainly consisted of Cu₂₀Sn₆ and Cu₃₉Sn₁₁ phases, which was revealed by an X‐ray diffraction (XRD) study. The high‐resolution Cu 2p XPS and Cu LMM Auger electron spectra indicate that metallic Cu oxidized to Cu⁺ and Cu²⁺ as the RF power on Cu target increased. The atomic ratios of Sn⁰ and Sn⁴⁺ decreased, while that of Sn²⁺ increased with increasing RF power on the Cu target. The polar surface free energy (SFE) component has a different tendency in comparison with the total SFE and the dispersive SFE component. The dispersive SFE component was the dominating contributing factor to the total SFE compared with the polar SFE. Copyright © 2016 John Wiley & Sons, Ltd.     

Surface modification of PVC endotracheal tubes by oxygen glow discharge to reduce bacterial adhesion

A d.c. oxygen glow discharge was used to modify medical‐grade poly(vinyl chloride) (PVC) to study how surface chemistry and hydrophilicity influence Pseudomonas aeruginosa adhesion. The effects of plasma exposure time on the resulting surface, including chemical composition, wettability and roughness, were assessed using x‐ray photoelectron spectroscopy, contact angle measurements and atomic force microscopy analysis. A significant alteration in the hydrophilicity of the native PVC surface was observed after oxygen glow discharge treatment. The water contact angle decreased from ～80° to 8–20°, with a weak dependence of the exposure time used. The change in surface wettability resulted from the incorporation of oxygenated functional groups, including esters, ketones and acids, as indicated by XPS analysis. The amount of oxygen incorporation was shown to be essentially independent of plasma exposure time. However, prolonged plasma exposure resulted in increased surface roughness. Bacterial adhesion efficiency was evaluated for PVC modified by 120 s of plasma exposure, because this exposure time was determined to yield the maximum decrease in contact angle. Oxygen plasma treatment of native PVC was found to yield a 70% reduction in bacterial adhesion for the four strains of Pseudomonas aeruginosa tested. Copyright © 2003 John Wiley & Sons, Ltd.     

Surface roughness and hydrophilicity enhancement of polyolefin‐based membranes by three kinds of plasma methods

The introduction of antibacterial property, conductivity, wettability and antithrombogenicity into polyolefin‐based membranes has evoked much attention, which can be achieved by coating hydrophilic polymers. Therefore, it is necessary to modify the roughness and hydrophilicity of polyolefin‐based membranes to enhance the coating ability. In this paper, three kinds of plasma methods, including inductively coupled (ICP) plasma, radio frequency low pressure (RFP) plasma and atmospheric dielectric barrier discharge (DBD) plasma, were used to modify the surface of the polyethylene (PE), polypropylene (PP) and polyester‐polypropylene (PET–PP) membranes. The surface roughness of the plasma‐modified PE, PP and PET–PP films was investigated by scanning electron microscopy (SEM) and atomic force microscope (AFM). The polar functional groups of films were observed by energy dispersive spectrometer (EDX) and X‐ray photoelectron spectroscopy (XPS). Besides, the hydrophilicity of the plasma‐modified PE, PP and PET–PP films was evaluated by water contact angle measurement. It was found that the surface roughness and hydrophilicity of plasma‐modified PE, PP and PET–PP films increased with the generation of oxygen‐containing functional groups (i.e. C―O, and C?O). The PET–PP membranes were treated by RFP plasma at different processing powers and times. These results indicated that plasma is an effective way to modify films, and the treatment time and power of plasma had a certain accumulation effect on the membranes' hydrophilicity. As for the roughness and hydrophilicity, the DBD plasma modifies the PE film, which is the optimum way to get the ideal roughness and hydrophilicity. Copyright © 2015 John Wiley & Sons, Ltd.     

Surface modification of plasma‐pretreated expanded poly (tetrafluroethylene) films by graft copolymerization

A two‐step process based on a low‐pressure helium plasma treatment followed by acrylic acid‐grafting copolymerization was used for the surface modification of expanded polytetrafluoroethylene (ePTFE) films. The effects of plasma treatment power and treatment time on the hydrophilicity of the film surface were investigated. The wettability of the ePTFE film surface was characterized by water contact angle, and the surface compositions of the untreated and treated ePTFE samples were evaluated by atomic force microscopy and XPS. Contact angle measurements revealed that the hydrophilicity of the ePTFE film surface was greatly enhanced by the combined actions of the plasma treatment and acrylic acid grafting, and the contact angle decreased from 145° to 66°. Atomic force microscopy analyses showed that the surface roughness increased after the plasma treatment. XPS analyses showed substantial increase in the concentration of carbon and oxygen atoms and a decrease in the concentration of fluorine atoms at the film surface. T‐peel strength showed an improved bonding strength between the film and an adhesive tape after the treatment. Copyright © 2012 John Wiley & Sons, Ltd.     

Free radical generation upon plasma treatment of cotton fibers and their initiation efficiency in surface-graft polymerization

Low-temperature plasma was used to activate mercerized cotton fabrics, to be followed by grafting with various methacrylates. Careful analysis of the experimental electron spin resonance (ESR) lineshapes of cotton samples treated at different RF powers made it possible to recognize and quantify four different species of free radicals still persistent 30 h after irradiation in the samples maintained under inert atmosphere. The decay rate of these species at room temperature was also evaluated with the analysis of the time evolution of the ESR spectra. The nature of the free radical species actually involved in the monomer grafting reaction has been discussed for cotton fabrics prepared under different plasma treatment conditions by analyzing the ESR lineshapes.     

氩等离子体后辉光区对聚四氟乙烯膜表面的优化改性

在理想管式反应器中, 采用Langmuir双电子探针和电子自旋共振(ESR)诊断技术分别定量测定了氩等离子体场中各活性物种的轴向分布, 并利用氩等离子体放电区及后辉光区对聚四氟乙烯(PTFE)进行了表面改性. 通过接触角测量、扫描电子显微镜和X 射线光电子能谱分析比较了改性前后常规及后辉光氩等离子体对PTFE表面结构及性能的影响. 结果表明, 氩等离子体中电子及离子浓度随轴向距离的增大迅速降低, 30 cm后接近于0, 而自由基浓度则降低缓慢, 40 cm处仍为初始浓度的96%. 氩等离子体放电功率、处理时间和气体流量强烈影响着PTFE表面润湿性的改善效果. 后辉光区因抑制电子和离子的刻蚀作用, 强化自由基反应, 使改性效果远优于常规氩等离子体. 经氩等离子体后辉光区短时间(30 s)处理后, PTFE表面化学成分发生了变化, F/C原子比从3.27降至2.30, O/C原子比从0.02增至0.09. 脱氟作用和含氧基团(如CO)的引入是有效改善PTFE表面润湿性的关键因素.     

Oxygen plasma-treatment effects on Si transfer

Oxygen plasma-treatment is commonly used to increase the hydrophilicity of poly(dimethylsiloxane) (PDMS) stamps used for microcontact printing (muCP) aqueous-based inks. Review of the literature reveals that a wide range of plasma parameters are currently employed to modify stamp surfaces. However, little is known about the effect of these parameters (e.g., power, chamber pressure, duration) on the undesirable transfer of low-molecular-weight silicon-containing fragments from the stamps that commonly occurs during muCP. To study the effect of oxygen plasma-treatment on Si transfer, unpatterned PDMS stamps were treated with oxygen plasma under various conditions and used to stamp deionized water on plasma-activated poly(methyl methacrylate) (PMMA) substrates. Once stamped, the PMMA substrates were analyzed with X-ray photoelectron spectroscopy (XPS) to quantify and characterize silicon present on the substrate surface. In addition, used PDMS stamps were analyzed with scanning electron microscopy (SEM) to observe topographical changes that occur during oxygen plasma-treatment. XPS results show that all plasma treatments studied significantly reduced the amount of Si transfer from the treated stamps during muCP as compared to untreated PDMS stamps and that the source of transfer is residual PDMS fragments not removed by oxygen plasma. SEM results show that, although the treated stamps undergo a variety of topographical changes, no correlation exists between stamp topography and extent of Si transfer from the stamps.     

In‐depth diffusion of oxygen into LDPE exposed to an Ar–O2 atmospheric post‐discharge: a complementary approach between AR‐XPS and Tof‐SIMS techniques

The in‐depth oxygen diffusion into a low density polyethylene film is performed in the post‐discharge of an atmospheric plasma torch, supplied in argon as carrier gas and with or without oxygen as reactive gas. The chemical and structural properties of the polymer surface and bulk are studied in terms of plasma parameters (treatment time, power, and reactive gas flow rate). A good correlation between XPS and Fourier transform infrared spectroscopy analyses is demonstrated. The penetration depth of oxygen into the bulk of the polymer is investigated by angle resolved‐XPS and time‐of‐flight SIMS. It is shown that, depending on the plasma conditions, oxygen could penetrate up to 20–40 nm into the low density polyethylene during the atmospheric plasma treatment. Copyright © 2014 John Wiley & Sons, Ltd.     

Influence of Oxygen Plasma Modification on Surface Free Energy of PMMA Films and Cell Attachment

For any biomaterial placed into a biological medium, the surface properties of the material, such as porosity, crystallinity, presence and distribution of electrical charge and functional groups are very critical parameters that determine the acceptance or rejection of the material. Applications, especially tissue engineering require some surface modifications at the molecular level without disturbing the bulk properties of the implants in order to enhance the cell attachment on the material. An appropriate technique is the application of glow discharge plasma which employs no solvents, takes place at ambient temperatures, and alterations take place only at the surface by changing the surface chemistry along with surface free energy (SFE) and efficiency for cell-material interaction. In this study, poly(methyl methacrylate) (PMMA) film surfaces were modified with oxygen plasma. SFE and its dispersive and polar (acidic-basic) components of the modified surfaces were calculated by means of several theoretical approaches including geometric mean, harmonic mean and acid-base equations. The relation between SFE and its dispersive and polar components and cell attachment on surfaces were studied. The highest 3T3 cell attachment was obtained for the surface with the total SFE of 61.77 mJ/m² and polar component of 50.91 mJ/m² according to Geometric mean. The total SFE of this surface was calculated to be 61.06 mJ/m² and the polar component as 40.96 mJ/m² using the Harmonic mean method.     

Enhancement of polymer hydrophobicity by SF6 plasma treatment and argon plasma immersion ion implantation

In this study sulphur hexafluoride (SF₆) plasmas and argon plasma immersion ion implantation (ArPIII) techniques have been applied to improve the hydrophobicity of poly(tetrafluoroethylene) (PTFE), polyurethane and silicone surfaces. As evaluated by water contact angle measurements, all the treatments resulted in a significant enhancement in the hydrophobicity of the polymers. However, exposure of the treated samples to air induced a strong variation in their hydrophobicity as a consequence of post‐plasma reactions between atmospheric species and remnant surface free radicals. X‐ray photoelectron spectroscopy results strongly suggest that for polyurethane and silicone the surface fluorination by SF₆ plasmas and the creation of new carbon bonds and radicals are the main agents for hydrophobicity enhancement. The PTFE exposed to ArPIII revealed increases in the contact angles after exposure to air. A significant incorporation of oxygen and the formation of new carbon bonds were revealed by XPS measurements. Copyright © 2003 John Wiley & Sons, Ltd.     

Plasma surface modification of poly (l-lactic acid) and poly (lactic-co-glycolic acid) films for improvement of nerve cells adhesion

Radio frequency (RF) plasma treatment in O₂ was applied to modify the surface of poly (l-lactic acid) (PLLA) and poly (d,l-lactic acid-coglycolic acid) (PLGA) as biodegradable polymers. The surface structure, morphology, wettability and surface chemistry of treated films were characterized by water drop contact angle measurement, scanning electron microscope (SEM), optical invert microscope, differential scanning calorimetry (DSC) and ATIR–FTIR spectroscopy. The cell affinity of the oxygen plasma treated film was evaluated by nervous tissue B65 cell culture in stationary conditions. The results showed that the hydrophilicity increased greatly after O₂ plasma treatment. The results showed that improved cell adhesion was attributed to the combination of surface chemistry and surface wettability during plasma treatment. Cell culture results showed that B65 nervous cell attachment and growth on the plasma treated PLLA was much higher than an unmodified sample and PLGA. Surface hydrophilicity and chemical functional groups with high polar component play an important role in enhancing cell attachment and growth.     

A comparison of the strength of autohesion of plasma treated amorphous and semi‐crystalline PEEK films

Polyether ether ketone (PEEK) is a promising material for the encapsulation of electronic components for medical implants but a strong and hermetic joining technology is required. Autohesion is a self‐bonding method that avoids the need for adhesives. The strengths of autohesive joins using amorphous and semi‐crystalline PEEK films after surface activation using RF plasma were compared. Both types of PEEK films showed successful autohesion after activation with the bond strength of the amorphous sample being twice as high as the bond strength of the semi‐crystalline sample. Plasma treatment increased the autohesion strength of PEEK with no observed change in surface roughness (as measured by profilometer). The water contact angle was reduced by the treatment. X‐ray photoelectron spectroscopy (XPS) was carried out to determine surface chemistry. In the case of the semi‐crystalline surface, plasma treatment increased the relative percentage of C? O functional groups compared to the untreated surface. For treated surfaces nitrogen concentration correlated positively with bond strength while oxygen concentration correlated negatively with the semi‐crystalline PEEK samples and positively with the amorphous PEEK samples. The oxygen groups most likely are formed after the treatment by ambient oxidation are not conducive to bond formation, possibly because of the quenching of radicals that would otherwise form links. Copyright © 2010 John Wiley & Sons, Ltd.     

Electron spin resonance study of γ-irradiated poly(methacrylic acid)

Low temperature relaxations in poly(methacrylic acid) (PMAA) have been studied by electron spin resonance (ESR) spectroscopy. The observed 8 line ESR spectra of irradiated PMAA in the temperature range 77-300K (LNT-RT) is attributed to the free radicals of the type ～ CH₂? CH? CH₃. Assignment of ESR spectra to free radicals has been made on the basis of magnetic parameters employed to simulate ESR spectra at different temperatures. Further, ESR spectra below LNT have been simulated, using the set of parameters employed to simulate the experimental spectrum at LNT. Magnetic parameters of the ESR spectra at LNT and below LNT indicate γ- and δ-relaxations of PMMA chains. © 1994 John Wiley & Sons, Inc.     

Surface modification of low-density polyethylene by inductively coupled argon plasma

The surface chemistry and nanotopography of low-density polyethylene (LDPE) were modified by downstream, inductively coupled, radio frequency (rf) Ar plasma without inducing surface damage. The extent of surface modification was controlled by the applied ion energy fluence, determined from the plasma ion density measured with a Langmuir probe. The treated LDPE surfaces were characterized by atomic force microscope (AFM) imaging, contact angle measurements, and X-ray photoelectron spectroscopy (XPS). Analysis of AFM surface images confirmed that topography changes occurred at the nanoscale and that surface damage was insignificant. Contact angle measurements demonstrated an enhancement of the surface hydrophilicity with the increase of the plasma power. XPS results showed surface chemistry changes involving the development of different carbon-oxygen functionalities that increased the surface hydrophilicity. Physical and chemical surface modification was achieved under conditions conducive to high-density inductively coupled rf plasma.     

Basic analytical investigation of plasma-chemically modified carbon fibers

The background of the present investigation is to enhance the overall adherence of vapor grown carbon fibers (VGCF) to the surrounding polymer matrix in different applications by forming polar groups at their surfaces and by modifying the surface morphology. This has been done by plasma treatments using a low-pressure plasma with different gases, flow rates, pressures and powers. Two different types of carbon fibers were investigated: carbon microfibers and carbon nanofibers. The characterization of fiber surfaces was achieved by photoelectron spectroscopy (XPS), contact angle measurements and titration. These investigations were accompanied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The oxygen plasma treatment of the fibers changes the surfaces by forming a layer with a thickness of the order of one nanometer mainly consisting of functional groups like hydroxyl, carbonyl and carboxyl. After functionalization of the complete surface, a further plasma treatment does not enhance the superficial oxygen content but changes slightly the portions of the functional groups. A comparison of the methods applied provides a largely consistent image of the effect of plasma treatment.