Heat capacities and thermodynamic properties of Ni9(btz)12(DMA)6(NO3)6

The low-temperature molar heat capacity of crystalline Ni₉(btz)₁₂(DMA)₆(NO₃)₆ (1) (btz = benzotriazolate; DMA = N,N′-dimethylacetamide) was measured by temperature-modulated differential scanning calorimetry for the first time. The thermodynamic parameters such as entropy and enthalpy relative to reference temperature 298.15 K were obtained based on the above molar heat capacity data. The compound was synthesized by solvothermal method and characterized by powder X-ray diffraction and FT-IR spectra. Moreover, the thermal stability and the decomposition mechanism of Ni₉(btz)₁₂(DMA)₆(NO₃)₆ were investigated by thermogravimetry (TG) analysis under air atmosphere from 300 to 873 K. The experimental results through TG measurement demonstrate that the compound has a two-stage mass loss in air flow.     

Studies on the pervaporation membrane of permeation water from methanol/water mixture

This investigation was performed to find if the nanometer SiO₂ added in the membranes can improve the pervaperation performance of the membranes. Acrylic acid (AA) and acrylonitrile (AN) were synthesized by solution polymerization with and without nanometer SiO₂. The copolymer solution was made into main body of the membranes, then composited with the polyvinyl alcohol (PVA) acetal membranes, to make the three-layer sandwich composite pervaporation membranes. The structure and the performance of the membranes were characterized by scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FT-IR), thermogravimetry (TG), dynamic themomechanical analysis apparatus (DMA) and mechanical property testing. Pervaporation experiments were carried out using these membranes to separate the mixtures of methanol/water over the complete concentration range 70–98%, and results showed that the selectivity of the membranes with nanometer SiO₂ had notable improvement. For the 98% mixture at 60 °C, the separate factor is up to 1458, which is improved more than 10 times compared to the membranes without nanometer SiO₂, the permeate flux is up to 325 g/(m² h). For the 70% mixture at 70 °C, the separate factor arrived at 12, the permeate flux is up to 7097 g/(m² h), which is improved more than 14 times compared to membranes without nanometer SiO₂. It was concluded that the pervaperation performance of the membranes can improve greatly by nanometer SiO₂.     

Polyisobutylene‐based polyurethanes: VII. structure/property investigations for medical applications

The outstanding hydrolytic and oxidative stabilities of polyisobutylene‐based polyurethanes (PIB‐based PUs) were reported earlier. Herein, we summarize recent investigations aimed at further enhancing hydrolytic‐oxidative stabilities (in terms of resistance to aqueous buffer, nitric acid and CoCl₂/H₂O₂) together with excellent mechanical properties. The purity and dryness of ingredients together with precise NCO/OH stoichiometry (～1.05) are essential to obtain PIB‐based PUs with improved properties. Static and dynamic mechanical properties were optimized by analyzing stress–strain traces, thermal (TGA, DSC) responses, self‐organization (XRD) profiles, and rheological (DMA, creep) information. According to microstructure and surface analyses (AFM, contact angle) annealing increases the segregation of individual segments and increases surface hydrophobicity, which in turn enhances the shielding of hydrolytically oxidatively vulnerable carbamate bonds by inert PIB barriers, and thus significantly improves hydrolytic‐oxidative stability. Annealing does not much affect bulk properties, such as static and dynamic mechanical and thermal properties; however, it increases damping over a wide temperature range. Annealed PIB‐based PU containing 72.5% PIB exhibits outstanding hydrolytic‐oxidative stability together with ～26 MPa tensile strength, ～500% elongation, and ～77 Microshore hardness. PIB‐based PUs are significantly more resistant to hydrolytic and oxidative degradation than ElastEon? E2A, a commercially available PDMS‐based PU, widely used for medical applications. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 532–543     

A coordination polymer with a (3,4)-connected (4·62)2(42 ·62 ·82) 2D network: synthesis,crystal structure and luminescent properties

The 2D Zn(II) coordination polymer with 2,3-dicarboxypyridine acid (2,3-H₂PDC) and dimethylamine (DMA) [Zn(2,3-PDC)(DMA)] _n (1) was synthesized under solvothermal conditions and characterized by FT-IR spectroscopy, TGA and luminescent analysis. X-ray crystallographic studies of 1 reveal that this metal-organic complex has an interesting (3,4)-connected 2D network with binary nodes. The Zn ions are four-connected nodes and the 2,3-PDC ligands are three-connected nodes. Luminescent study indicates 1 has an emissive maximum at 403?nm in the solid state at room temperature.     

Influence of polyfurfuryl alcohol (PFA) loading on the properties of Nafion composite membranes

Composite membranes based on Nafion (N115) loaded with furfuryl alcohol (FA) were prepared by in situ acid-catalyzed polymerization technique, with the aim to improve the ionic conductivity of Nafion membranes. The functionalization, thermal stability, electrical properties and mechanical strength of N115-PFA composites was analyzed by means of Fourier transform infrared (FT-IR) attenuated total reflection (ATR) spectroscopy, small- and wide-angle X-ray scattering (SAXS/WAXS), thermogravimetric analysis (TGA), electrical impedance spectroscopy, dynamic vapor sorption (DVS) and dynamic mechanical analyser (DMA). The FA loading in the resultant composites had a positive correlation with the water uptake (W_u), water vapor uptake (W_vu), ionic conductivity and thermo-mechanical stability. At low polyfurfuryl alcohol (PFA) loading, these membranes displayed higher W_u and improved ionic and electrical properties. Further, the thermo-mechanical stability also gradually increased with the PFA loading. All the composites showed a well-defined glass transition temperature in DMA, which shifted to higher temperature with repeated PFA loading. Overall, the results indicate that the developed composite membrane are promising for low temperature polymer electrolyte membrane (PEM) fuel cells.     

Polyurethanes with separately tunable biodegradation behavior and mechanical properties for tissue engineering

Two series (random and block) poly(glycolide‐co‐ε‐caprolactone) macrodiols with various glycolide to ε‐caprolactone ratios (50/50 and 30/70, R‐PG50C, R‐PG30C, B‐PG50C, and B‐PG30C) were synthesized. Next, segmented polyurethanes (PUs) were synthesized based on the synthesized macrodiols, 1,6‐hexamethylene diisocyanate and 1,4‐butanediol (PU‐R30, PU‐R50, PU‐B30, and PU‐B50). Effect of glycolide (G) and ε‐caprolactone (C) monomers arrangement (random or block) on the PUs properties were investigated via FTIR, ¹H NMR, DSC, TGA, DMA, SEM, and mechanical tests. All PUs illustrated T_g (−33°C to −48°C) and T_m (102°C to 139°C) corresponding to the soft and the hard segments, respectively. Polymers based on block macrodiols also showed T_m related to the soft segments. While PUs underwent a two‐step thermal degradation, the PUs based on block macrodiols indicated higher degradation temperature. Dynamic mechanical analysis results evidenced development of a well‐defined microphase separated structure in PU‐R30. Contact angle (about 70°‐80°) and water uptake (around 20% after 24 hours) of the PU films are close to those suitable for tissue engineering materials. The PU based on R‐PG30C (PU‐R30) exhibited the highest tensile strength (2.87 MPa) followed by PU‐B50 and PU‐R50. Over a 63‐day in vitro degradation study in phosphate buffered saline, the PUs showed variable weight loss (up to 40%) depending on their soft segments composition and arrangement. Also, the PUs showed no cytotoxicity. Thus, these PUs with tunable biodegradation rate and mechanical properties are suitable candidates for tissue engineering.     

Synthesis and properties of polystyrene/polydimethylsiloxane graft copolymers

Polystyrene-graft-polydimethylsiloxane (PS-g-PDMS) copolymers with different PDMS content were synthesized by the radical bulk copolymerization of PDMS macromonomer and styrene. The copolymers were characterized by Fourier transform infrared (FT-IR), ¹H-nuclear magnetic resonance (NMR), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), transmission electron microscopy (TEM) and the mechanical properties of the copolymers were also carried out. It was indicated that the notched impact strength and elongation at break of the polymers increased with the increase of PDMS content. The thermal stability of PS-g-PDMS is better than that of PS. __________ Translated from Journal of East China University of Science and Technology 2005, 31(2) (in Chinese)     

Electrical and structural analysis of conductive polyaniline/polyacrylonitrile composites

Conducting composites of polyacrylonitrile (PAN) copolymer containing 10% mass ratio methylacrylate and dodecylbenzene sulfonic acid doped polyaniline (PANI-DBSA) were prepared by solution blending. Electrical properties of the blends were characterized by means of electrical conductivity measurements and the phase structures were investigated via scanning electron microscopy (SEM), X-ray diffraction (XRD), FT-IR spectroscopy, differential scanning calorimetry (DSC) and dynamical mechanical analysis (DMA). It was found that the electrical conductivity of the composites increased with the increase of PANI-DBSA content and the percolation threshold lay around 3.2 wt%. DSC and DMA measurements showed that there was only one T_g for each blend and the values of T_g varied with the PANI-DBSA content, implying that the PANI-DBSA/PAN blend was at least partially compatible. The formation of the hydrogen bonding between the carbonyl groups in PAN copolymer and the imine groups in PANI-DBSA was identified by the FT-IR spectra. XRD demonstrated that the intrinsic layered arrangement of PANI-DBSA was disaggregated in the blends. Nanosize network structure of PANI-DBSA dispersing in PAN matrix and the so-called phase reverse occurring in the skin layer of the film samples at low PANI-DBSA loading were observed by SEM.     

Microemulsion Synthesis of Nanosized TiO2 Particles Doping with Rare-Earth and their Photocatalytic Activity

Microemulsion is the easiest and cleanest of the popular methods of synthesizing nanomaterial. This work synthesized the nanosized La-TiO₂ and Ce-TiO₂ particles through the hydrolyzation of tetrabutyl titanate in a Triton X-100/n-hexanol/cyclohexane/water reverse microemulsion. The particles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform-infrared spectroscopy (FT-IR) and thermogravimetry (TG). The photocatalytic activity was evaluated by photocatalytic degradation of methyl orange (MO) under ultraviolet light and visible light irradiation. The results showed that reverse microemulsion produced the nanosized and well-separated particles, which are obviously in degrading MO. Comparing the pure TiO₂ with doping TiO₂, the doping ones are smaller and have better photocatalytic activity, which was best at the molar content of 0.1% for La, whereas for Ce it was 0.5%.     

Polyisobutylene‐based polyurethanes. V. Oxidative‐hydrolytic stability and biocompatibility

The oxidative/hydrolytic stability of polyurethanes (PUs) containing exclusively polyisobutylene (PIB), or mixed PIB/polytetramethylene oxide (PTMO), or mixed PIB/polyhexamethylene carbonate (PC) soft segments was investigated. The tensile strengths and elongations of various PUs were determined before and after agitating in 35% HNO₃ or 20% H₂O₂/0.1 M CoCl₂ solutions and retentions were quantified. The presence of PIB imparts significant oxidative/hydrolytic resistance. The tensile strength and elongation of PUs containing 70% PIB, or those of mixed PIB/PC soft segments with 50% PIB, remained essentially unchanged upon exposure to HNO₃; in contrast, PUs containing mixed PIB/PTMO soft segments with 50% PIB underwent significant degradation. The tensile strength of PUs with mixed PIB/PC (60/10%) soft segment increased after exposure to HNO₃, most likely because of oxidative crosslinking of PC segments. PIB/PTMO‐ and PIB/PC‐based PUs and commercially available PUs (Elast‐Eon® and Carbothane®) were exposed to H₂O₂/CoCl₂ solutions for up to 14 weeks. Although the experimental PIB/PC‐based PUs exhibited negligible change in mechanical properties and no surface damage, Elast‐Eon® and Carbothane® showed significant surface damage. PIB‐based polyureas and Bionate® were implanted in rats for 4 weeks in vivo, and their biocompatibility was investigated. The biocompatibility of PIB‐based materials was superior to Bionate®. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2194–2203, 2010     

Biodegradable Polyurethanes from Plant Components

Abstract

Polyurethane (PU) sheets and foams having plant components in their network were prepared by using the following procedure. Polyethylene glycol (PEG) was mixed with one of the following; molasses, lignin, woodmeal, or coffee grounds. The mixture obtained was reacted with diphenylmethane diisocyanate (MDI) at room temperature, and precured PUs were prepared. The precured PUs were heat-pressed and PU sheets were obtained. In order to make PU foam, the above mixture was reacted with MDI after the addition of plasticizer, surfactant (silicone oil), catalyst (di-n-butyltin dilaurate), and droplets of water under vigorous stirring. The glass transition temperature, tensile and compression strengths, and Young's modulus of the PU sheets and foams increased with an increasing amount of plant components. This suggests that saccharide and lignin residues act as hard segments in PUs. It was found that the PUs obtained were biodegradable in soil. The rate of biodegradation of the PUs derived from molasses and coffee grounds was between that of cryptomeria (Cryptomeria japonica) and beech (Fagus sieboldi).     

Solid-state compounds of 2-methoxybenzylidenepyruvate and 2-methoxycinnamyllidenepyruvate with thorium (IV)

Solid-state compounds of general formula ThL₄·nH₂O, where L represents 2-methoxybenzylidenepyruvate and 2-methoxycynamylidenepyruvate, were synthesized. Complexometric titrations with EDTA, thermogravimetry (TG), differential thermal analysis (DTA), X-ray powder diffractometry, elemental analysis (EA), and infrared spectroscopy have been employed to characterize and to study the thermal behavior of these compounds in dynamic air atmosphere. The results led to informations about the composition, dehydration, crystallinity, and thermal decomposition of the isolated compounds. The performed molecular calculations in this study were done using the Gaussian 03 routine. Theoretical calculations help in interpretations of FT-IR spectra supplying structural and physicochemical parameters.     

Emulsion copolymerization of fluorinated acrylate in the presence of a polymerizable emulsifier

An emulsifier-free fluorinated polyarcylate emulsion was synthesized by a seed emulsion polymerization method from methyl methacrylate (MMA), butyl acrylate (BA) and hexafluorobutyl methacrylate (HFMA) in the presence of a polymerizable emulsifier—ammonium allyloxtmethylate nonylphenol ethoxylates sulfate (DNS-86). Influences of the DNS-86 level on electrolyte stability of the emulsifier-free emulsion were discussed. In addition, the emulsion and the films were characterized by Fourier transformed infrared (FT-IR) spectrometry, nuclear magnetic resonance (¹H NMR) spectrometry, transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), thermogravimetry (TG), and contact angle (CA) analysis, respectively. The FT-IR spectra and ¹H NMR spectrum showed that HFMA was effectively involved in the emulsion copolymerization and monomers formed the fluorine-containing acrylate copolymer. The resulted emulsion particles had a core–shell structure and a narrow particle size distribution. XPS and CA analysis revealed that a gradient concentration of fluorine existed along the depth profile of the fluorine-containing emulsion film. One side of the film was richer in fluorine and more hydrophobic than the other side. The film formed from the fluorine-containing emulsion showed higher thermal stability than that of the fluorine-free emulsion.     

Synthesis and chemical structure of natural rubber adduct with SO2 and study of the thermal stability

Natural rubber (NR, cis-1,4-polyisoprene) was reacted in solution with SO₂ at room temperature in different solvents (tetrahydrofuran, CHCl₃, CH₂Cl₂ and tetralin). The reaction product consisted of an adduct between NR and SO₂. The chemical structure of the adduct was studied by FT-IR spectroscopy, by thermogravimetry coupled with FT-IR (TGA-FT-IR), by differential thermal analysis (DTA) and by derivative thermogravimetry (DTG). The maximum SO₂ uptake from NR was 21% as determined by TGA. The TGA of the NR-SO₂ shows that the adduct decomposes in two steps initially releasing SO₂ at lower temperature and then decomposing at higher temperature like common NR. It is proposed that the chemical structure of the NR-SO₂ adduct consists of SO₂ molecules added to the double bonds of the isoprene units forming a sulfone derivative with three-membered rings known as thiirane-1,1-dioxide. On heating the thiirane ring decomposes releasing SO₂ in an extrusion reaction giving back the NR macromolecule.The possible potential applications of the NR-SO₂ adduct which is cheap and easy to prepare are outlined.     

Thermal Decomposition of Neodymium Amide Complexes

The decomposition of NdCl₃ L(L = N,N-dimethylformamide [DMF] or N,N-dimethyacetamide [DMA]) compounds has been investigated by thermogravimetric and differential thermal analysis (TGA and DTA) coupled with Fourier transform infrared (FTIR) spectroscopy. When heated in air, the NdCl₃L compounds decompose by a mechanism involving oxidation of the amide ligand to CO₂ and HCl. Some free armide is also released in the thermal decomposition in air. However, when heated under nitrogen, clean release of DMA or DMF is observed. In both cases, the amide is released two steps. From 30 to 40% of the amide is initially released with little or no associated enthalpy as measured by DTA. As the temperature is increased, the remaining 60 to 70% of the amide is released via an endothermic process. The enthalpy for this release is 53.1 - 3.8 kJ/mole for DMF and 40.9 - 1.1 kJ/mole for DMA, suggesting that DMF binds more strongly to Nd(III) than does DMA. Steric effects caused by the additional methyl group in DMA might be responsible for the weaker binding of this amide compared to DMF.     

Effects of hard‐segment polymers on CO2/N2 gas‐separation properties of poly(ethylene oxide)‐segmented copolymers

Poly(ethylene oxide)‐segmented polyurethanes (PEO‐PUs) and polyamides (PEO‐PAs) were prepared, and their morphology and CO₂/N₂ separation properties were investigated in comparison with those of PEO‐segmented polyimides (PEO‐PIs). The contents of the hard and soft segments in the soft and hard domains, W_HS and W_SH, respectively, were estimated from glass‐transition temperatures with the Fox equation. The phase separation of the PEO domains depended on the kind of hard‐segment polymer; that is, W_HS was in the order PU > PA ≫ PI for a PEO block length (n) of 45–52. The larger W_HS of PUs and PAs was due to hydrogen bonding between the oxygen of PEO and the NH group of urethane or amide. The CO₂/N₂ separation properties depended on the kind of hard‐segment polymer. Compared with PEO‐PIs, PEO‐PUs and PEO‐PA had much smaller CO₂ permeabilities because of much smaller CO₂ diffusion coefficients and somewhat smaller CO₂ solubilities. PEO‐PUs also had a somewhat smaller permselectivity because of a smaller solubility selectivity. This was due to the larger W_HS of PEO‐PUs and PEO‐PAs, that is, a greater contamination of PEO domains with hard urethane and amide units. For PEO‐PIs, with a decrease in n to 23 and 9, W_HS became large and CO₂ permeability decreased significantly, but the permselectivity was still at a high level of more than 50 at 35 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1707–1715, 2000     

Synthesis,Structure, and Characterization of a Microporous Metal‐Organic Framework with PtS Topology

The microporous metal‐organic framework Cd₂(ABTC)(H₂O)(DMA)₂ · H₂O · 3DMA ( 1 ) (H₄ABTC = 3, 3′,5, 5′‐azobenzenetetracarboxylic acid; DMA = N,N′‐dimethylacetamide) was prepared by solvothermal reaction and characterized. X‐ray structure analysis revealed that compound 1 is a three‐dimensional (3D) open framework with 2D channels. The topology is based on a PtS net, constructed of 4‐connected rectangular ABTC^4– units with 4‐connected tetrahedral dinuclear Cd₂(CO₂)₄(H₂O)(DMA)₂ secondary building units (SBUs). The solid‐state excitation‐emission spectra showed that the strongest emission peak is at 403 nm upon excitation at λ = 287 nm.     

Effect of polyol structure on the properties of the resultant magnetic polyurethane elastomer nanocomposites

In this study, two types of magnetic polyurethane (PU) elastomer nanocomposites using polycaprolactone (PCL) and polytetramethylene glycol (PTMG) as polyols were synthesized by incorporating thiodiglycolic acid surface modified Fe₃O₄ nanoparticles (TSM‐Fe₃O₄) into PU matrices through in situ polymerization method. TSM‐Fe₃O₄ nanoparticles were prepared using in situ coprecipitation method in alkali media and were characterized by X‐ray diffraction, Fourier Transform Infrared Spectrophotometer, Transmission Electron Microscopy, and Vibrating Sample Magnetometer. The effects of PCL and PTMG polyols on the properties of the resultant PUs were studied. The morphology and dispersion of the nanoparticles in the magnetic nanocomposites were studied by Scanning Electron Microscope. It was observed that dispersion of nanoparticles in PTMG‐based magnetic nanocomposite was better than PCL‐based magnetic nanocomposite. Furthermore, the effect of polyol structure on thermal and mechanical properties of nanocomposite was investigated by Thermogravimetric Analysis and Dynamic Mechanical Thermal Analysis. A decrease in the thermal stability of magnetic nanocomposites was found compared to pure PUs. Furthermore, DMTA results showed that increase in glass transition temperature of PTMG‐based magnetic nanocomposite is higher than PCL‐based magnetic nanocomposite, which is attributed to better dispersion of TSM‐Fe₃O₄ nanoparticles in PTMG‐based PU matrix. Additionally, magnetic nanocomposites exhibited a lower level of hydrophilicity compared to pure PUs. These observations were attributed to the hydrophobic behavior of TSM‐Fe₃O₄ nanoparticles. Moreover, study of fibroblast cells interaction with magnetic nanocomposites showed that the products can be a good candidate for biomedical application. Copyright © 2013 John Wiley & Sons, Ltd.     

Catalytic effect analysis of metallic additives on light crude oil by TG and DSC tests

This research aimed at the investigation of the effect of different metallic additive on the combustion and kinetic behavior of crude oil. For this purpose, the thermal behavior of the oil-only and oil–metallic salts mixtures were studies by the thermogravimetry (TG)/derivative thermogravimetry and differential scanning calorimetry (DSC) on heating rate at 10 °C min^?1. The result shows that Dagang crude oil exhibited apparent low temperature oxidation (LTO), fuel deposition, and high temperature oxidation processes. With the addition of metallic salts, the LTO process has been shortened and samples added CuSO₄, CrCl₃·6H₂O, and AlCl₃·6H₂O achieved a much lower peak temperature than that of oil. Based on the Arrhenius model, metallic additives were proven to have obvious influence on the combustion activation energy. And, by comprehensive analysis of TG/DSC profile and activation energy, ZnSO₄ exhibited a positive influence on light crude oil combustion during the high pressure air injection process.     

Thermal characterization and electrical properties of Fe-modified cellulose long fibers and micro crystalline cellulose

Thermal properties of polylactic acid (PLA) filled with Fe-modified cellulose long fibers (CLF) and microcrystalline cellulose (MCC) were studied using thermo gravimetric analysis (TG), differential scanning calorimetry, and dynamic mechanical analysis (DMA). The Fe-modified CLFs and MCCs were compared with unmodified samples to study the effect of modification with Fe on electrical conductivity. Results from TG showed that the degradation temperature was higher for all composites when compared to the pure PLA and that the PLA composites filled with unmodified celluloses resulted in the best thermal stability. No comparable difference was found in glass transition temperature (T _g) and melting temperature (T _m) between pure PLA and Fe-modified and unmodified CLF- and MCC-based PLA biocomposites. DMA results showed that the storage modulus in glassy state was increased for the biocomposites when compared to pure PLA. The results obtained from a femtostat showed that electrical conductivity of Fe-modified CLF and MCC samples were higher than that of unmodified samples, thus indicating that the prepared biocomposites have potential uses where conductive biopolymers are needed. These modified fibers can also be tailored for fiber orientation in a matrix when subjected to a magnetic field.