Influence of the pore structure of MCM-41 and SBA-15 silica fibers on atomic layer chemical vapor deposition of cobalt carbonyl

Mesoporous high surface area MCM-41 and SBA-15 type silica materials with fibrous morphology were synthesized and used as support materials for the ALCVD (atomic layer chemical vapor deposition) preparation of Co/MCM-41 and Co/SBA-15 catalysts. Co/MCM-41 and Co/SBA-15 catalysts were prepared by deposition of Co2(CO)8 from the gas phase onto the surfaces of preheated support materials in a fluidized bed reactor. For both silica materials, two different kinds of preparation methods, direct deposition and a pulse deposition method, were used. Pure silica supports as well as supported cobalt catalysts were characterized by various spectroscopic (IR) and analytical (X-ray diffraction, Brunauer-Emmett-Teller, elemental analysis) methods. MCM-41 and SBA-15 fibers showed considerable ability to adsorb Co2(CO)8 from the gas phase. For MCM-41 and SBA-15 silicas, cobalt loadings of 13.7 and 12.1 wt % were obtained using the direct deposition method. The cobalt loadings increased to 23.0 and 20.7 wt % for MCM-41 and SBA-15 silicas, respectively, when the pulse deposition method was used. The reduction behavior of silica-supported cobalt catalysts was found to depend on the catalyst preparation method and on the mesoporous structure of the support material. Almost identical reduction properties of SBA-15-supported catalysts prepared by different deposition methods are explained by the structural properties of the mesoporous support and, in particular, by the chemical structure of the inner surfaces and walls of the mesopores. Pulse O2/H2 chemisorption experiments showed catalytically promising redox properties and surface stability of the prepared MCM-41- and SBA-15-supported cobalt catalysts.     

载体焙烧温度对Rh-Mn-Li/SBA-15催化CO加氢性能的影响

SBA-15分别于550、700、800和900℃进行焙烧,然后以等体积共浸渍法将Rh、Mn和Li负载其上。催化剂的性能用CO加氢反应进行评价。催化剂分别用N₂物理吸附、X射线衍射、透射电子显微镜、H₂化学吸附和傅里叶变换红外光谱进行表征。即使在900℃下进行焙烧,SBA-15的结构仍得到保持。但是,当焙烧温度从550℃升高到900℃,SBA-15的比表面积、孔径和总孔容分别从842.6 m²·g^-1、9.57 nm和1.18 cm³·g^-1降到246.4 m²·g^-1、5.62 nm和0.34 cm³·g^-1。此外,Rh颗粒的尺寸都在1.5-4.0 nm范围内,并且随着载体的焙烧温度增加而增加。另外,Rh颗粒更倾向位于高温焙烧载体的介孔内,这可能是因为经过高温焙烧,载体微孔下降。所以,H₂和CO更易与负载在高温焙烧后的载体上的Rh颗粒接触。因此,当载体焙烧温度达到900℃时,Rh-Mn-Li/SBA-15催化剂有非常高的C₂₊含氧化合物的活性和选择性。     

Comprehensive study of nanostructured supports with high surface area for Fischer-Tropsch synthesis

An extensive study of Fischer-Tropsch synthesis on nanostructure supports with high surface area such as nanostructure γ-alumina, single wall carbon nanotubes (SWNTs), and the hybrid of SWNTs/nanostructure γ-alumina has been investigated. The nanostructure γ-alumina was promoted with lanthanum to obtain better performance of catalyst and 15 wt% cobalt loading was the basis of our investigation. Fischer-Tropsch synthesis was performed in a fixed bed reactor under different reaction conditions (220–240 °C, 15–25 bar, H₂/CO ratio of 2, GHSV of 900–1400) in order to study the effects of temperature, pressure and gas hourly space velocity (GHSV) changes on hydrocarbon selectivity and catalyst activity. The catalysts were extensively characterized by different methods including X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), inductively coupled plasma (ICP), hydrogen (H₂) chemisorption and temperature-programmed reduction (TPR). The results showed that the yield of hybrid supported catalyst (55.4%) is higher than that of nanostructure γ-alumina supported catalyst (55.0%) and lower than that of SWNTs supported cobalt catalyst (71.0%). The hybrid supported catalyst showed higher reduction degree and dispersion of cobalt particles. The temperature, pressure and GHSV effects on hybrid supported catalyst were studied and results showed that higher pressure favors the chain growth and temperature increase leads to the increases in methane selectivity and CO conversion. Higher hydrocarbon selectivity and CO conversion showed positive relationship with increasing GHSV while lower hydrocarbon selectivity diminishes.     

Synthesis, characterization, and luminescence properties of the ternary europium complex covalently bonded to mesoporous SBA-15

A novel mesoporous SBA-15 type of hybrid material (phen-SBA-15) covalently bonded with 1,10-phenanthroline (phen) ligand was synthesized by co-condensation of tetraethoxysilane (TEOS) and the chelate ligand 5-[N,N-bis-3-(triethoxysilyl)propyl]ureyl-1,10-phenanthroline (phen-Si) in the presence of Pluronic P123 surfactant as a template. The preservation of the chelate ligand structure during the hydrothermal synthesis and the surfactant extraction process was confirmed by Fourier transform infrared (FTIR) and (29)Si MAS NMR spectroscopies. SBA-15 consisting of the highly luminescent ternary complex Eu(TTA)(3)phen (TTA = 2-thenoyltrifluoroacetone) covalently bonded to a silica-based network, which was designated as Eu(TTA)(3)phen-SBA-15, was obtained by introducing the Eu(TTA)(3).2H(2)O complex into the hybrid materials via a ligand exchange reaction. XRD, TEM, and N(2) adsorption measurements were employed to characterize the mesostructure of Eu(TTA)(3)phen-SBA-15. For comparison, SBA-15 doped with Eu(TTA)(3).2H(2)O and Eu(TTA)(3)phen complexes and SBA-15 covalently bonded with a binary europium complex with phen ligand were also synthesized, and were named SBA-15/Eu(TTA)(3), SBA-15/Eu(TTA)(3)phen, and Eu-phen-SBA-15, respectively. The detailed luminescence studies on all the materials showed that, compared with the doping sample SBA-15/Eu(TTA)(3)phen and binary europium complex functionalized sample Eu-phen-SBA-15, the Eu(TTA)(3)phen-SBA-15 mesoporous hybrid material exhibited higher luminescence intensity and emission quantum efficiency. Thermogravimetric analysis on Eu(TTA)(3)phen-SBA-15 demonstrated that the thermal stability of the lanthanide complex was evidently improved as it was covalently bonded to the mesoporous SBA-15 matrix.     

Adsorption and co-adsorption of ethylene and carbon monoxide on silica-supported monodisperse Pt nanoparticles: volumetric adsorption and infrared spectroscopy studies

The adsorption of carbon monoxide and ethylene, and their sequential adsorption, was studied over a series of Pt/SBA-15 catalysts with monodisperse particle sizes ranging from 1.7 to 7.1 nm by diffuse-reflectance infrared spectroscopy and chemisorption. Gas adsorption was dependent on the Pt particle size, temperature, and sequence of gas exposure. Adsorption of CO at room temperature on Pt/SBA-15 gives rise to a spectroscopic feature assigned to the C-O stretch: nu(CO) = 2075 cm-1 (1.9 nm); 2079 cm-1 (2.9 nm); 2082 cm-1 (3.6 nm); and 2090 cm-1 (7.1 nm). The intensity of the signal decreased in a sigmoidal fashion with increasing temperature, thereby providing semiquantitative surface coverage information. Adsorption of ethylene on Pt/SBA-15 gave rise to spectroscopic features at approximately 1340, approximately 1420, and approximately 1500 cm-1 assigned to ethylidyne, di-sigma-bonded ethylene, and pi-bonded ethylene, respectively. The ratio of these surface species is highly dependent on the Pt particle size. At room temperature, Pt particles stabilize ethylidyne as well as di-sigma- and pi-bonded ethylene; however, ethylidyne predominated on the surfaces of larger particles. Ethylidyne was the only identifiable species at 403 K, with its formation being more facile on larger particles. Co-adsorption experiments reveal that the composition of the surface layer is dependent on the order of exposure to gases. Exposure of a C2H4-covered Pt surface to CO resulted in an approximately 50% decrease in chemisorbed CO compared to a fresh Pt surface. The nu(CO) appeared at 2050 cm-1 on Pt/SBA-15 pretreated with C2H4 at room temperature. The di-sigma-bonded and pi-bonded species are the most susceptible to displacement from the surface by CO. The formation of ethylidyne appeared to be less sensitive to the presence of adsorbed carbon monoxide, especially on larger particles. Upon exposure of C2H4 to a CO-covered Pt surface, little irreversible uptake occurred due to nearly 100% site blocking. These results demonstrate that carbon monoxide competes directly with ethylene for surface sites, which will have direct implications on the poisoning of the heterogeneously catalyzed conversion of hydrocarbons.     

Co/SBA-16:对柴油组分有高选择性的费托合成催化剂(英文)

使用浸渍法制备了一系列Co/SBA-16催化剂,并通过氮物理吸附、X射线衍射、氢程序升温还原、氢化学吸附和透射电镜技术对催化剂行了表征。研究表明,随着负载钴含量的增加,金属钴的分散度降低了,这是同Co3O4晶粒增长和比表面积降低相一致的。Co/SBA-16催化剂展示了高的一氧化碳转化率,低的C1选择性和高的C5+选择性,特别对柴油组分有高选择性。     

Covalent heterogenization of a discrete Mn(II) bis-phen complex by a metal-template/metal-exchange method: an epoxidation catalyst with enhanced reactivity

Considerable attention has been devoted to the immobilization of discrete epoxidation catalysts onto solid supports due to the possible benefits of site isolation such as increased catalyst stability, catalyst recycling, and product separation. A synthetic metal-template/metal-exchange method to imprint a covalently attached bis-1,10-phenanthroline coordination environment onto high-surface area, mesoporous SBA-15 silica is reported herein along with the epoxidation reactivity once reloaded with manganese. Comparisons of this imprinted material with material synthesized by random grafting of the ligand show that the template method creates more reproducible, solution-like bis-1,10-phenanthroline coordination at a variety of ligand loadings. Olefin epoxidation with peracetic acid shows the imprinted manganese catalysts have improved product selectivity for epoxides, greater substrate scope, more efficient use of oxidant, and higher reactivity than their homogeneous or grafted analogues independent of ligand loading. The randomly grafted manganese catalysts, however, show reactivity that varies with ligand loading while the homogeneous analogue degrades trisubstituted olefins and produces trans-epoxide products from cis-olefins. Efficient recycling behavior of the templated catalysts is also possible.     

氨基硅烷修饰的SBA-15用于CO2的吸附

以3-丙胺基三乙氧基硅烷(APTES)为硅烷化试剂,分别采用后修饰法和一步嫁接法将其嫁接到SBA-15的孔内,形成了功能化的介孔分子筛用于CO2吸附.利用X射线衍射和氮气物理吸附等方法考察了嫁接前后SBA-15的孔结构变化,用静态吸附天平考察了不同温度和不同分压下CO2的吸附行为.实验结果表明,一步嫁接法比后修饰法更有利于实现APTES在SBA-15上的嫁接.与传统的活性炭吸附剂相比,该种介孔分子筛更有利于较低分压下CO2的吸附脱除.     

还原气氛对CoFe/SBA-15催化剂F-T反应性能的影响

考察了不同还原气氛处理CoFe/SBA-15催化剂对F-T反应性能的影响。结果表明,H2气氛下有利于六方钴的生成;催化剂的活性取决于钴含量,随着钴含量的增加,F-T反应中CO转化率增加,C5+选择性增加。随着铁含量的增加,催化剂表现了较高的CO2选择性。CO还原有利于立方钴的生成,导致催化活性相比H2还原的催化剂活性要低。同时CO还原容易产生积炭使催化剂的钴活性位被覆盖,导致甲烷选择性随着钴含量增加而升高。但碳化铁的生成有利于提高20Fe/SBA-15催化剂的活性,有利于低碳烃生成及C2~4烃烯烷比增加。     

Reactions of cerium atoms and dicerium molecules with CO: formation of cerium carbonyls and photoconversion to CO-activated insertion molecules

Reactions of cerium with carbon monoxide molecules in solid argon have been studied using matrix isolation infrared absorption spectroscopy. The cerium carbonyls CeCO and Ce2CO are produced spontaneously on annealing and they are photochemically rearranged to the CCeO and c-Ce2(mu-C)(mu-O) isomers, where Ce and Ce2 are inserted into the CO triple bond. Theoretical calculations indicate that CeCO is an end-on-bonded carbonyl with a quintet ground state, whereas Ce2CO is a rare dinuclear lanthanide carbonyl complex with CO serving as an asymmetrically bridged, side-on ligand. The CCeO molecule was theoretically characterized to have a linear structure with a singlet ground state. Evidence is also presented for the CeCO- anion and other cerium carbonyls with higher coordination numbers.     

Ultrasound-assisted polyol method for the preparation of SBA-15-supported ruthenium nanoparticles and the study of their catalytic activity on the partial oxidation of methane

Metallic Ru nanoparticles have been successfully produced and incorporated into the pores of SBA-15 in situ employing a simple ultrasound-assisted polyol method. The product has been confirmed by X-ray diffraction, transmission electron microscopy, and X-ray photoelectron spectroscopy, where ultrasound provides both the energy for the reduction of the Ru(III) ion and the driving force for the loading of the Ru(0) nanoparticles into the SBA-15 pores. An ultrasound-assisted insertion mechanism has been proposed based on the microjets and shake-wave effect of the collapsed bubbles. The catalytic properties of the SBA-15-supported Ru nanoparticles have been tested by the partial oxidization of methane and show very high activity and high CO selectivity.     

二次嫁接法合成多金属氧酸盐/介孔分子筛杂化材料

合成了表面含有SiOH基团的钨磷酸盐衍生物(Bu4N)3PW11O39[O(SiOH)2] (TBAPW11Si2), 并通过其与纯硅介孔分子筛SBA-15表面SiOH的缩合反应, 将TBAPW11Si2二次嫁接到SBA-15的介孔孔道中, 得到了TBAPW11Si2/SBA-15介孔杂化材料. 表征结果显示, 孔内TBAPW11Si2的Keggin结构保留完整, 并与孔壁共价键联. 样品仍保持六方对称的孔阵结构, 但孔道部分被堵, 孔容、孔径、比表面积下降. 该杂化样品对甲基橙的光催化降解不仅显示高催化活性, 而且由于键联的多金属氧酸盐在水溶液中的抗浸取能力强, 催化剂的使用寿命大大延长.     

Electrocatalytic oxidation of carbon monoxide and methanol at Pt nanoparticles confined in SBA-15: voltammetric and in situ infrared spectroscopic studies

Electrocatalytic oxidation of carbon monoxide and methanol at Pt nanoparticles confined in mesoporous molecular sieve SBA-15 was studied by using cyclic voltammetry and in situ FTIR spectroscopy. Cyclic voltammetric studies revealed that the Pt nanoparticles confined in SBA-15 exhibit a high activity in the presence of hydrated phase consisting of SiO₂ in the SBA-15. In situ FTIR spectroscopy results discovered that IR absorption of CO adsorbed on Pt nanoparticles confined in SBA-15 has been enhanced 11-fold, and the full-width at half-maximum of the CO band is significantly increased, in comparison with IR feature of CO adsorbed on a bulk Pt electrode. The linearly adsorbed CO species is the only intermediate derived from dissociative adsorption of methanol, which is more readily oxidized to form CO₂ in the aid of the active oxide in SBA-15.This paper is dedicated to Professor G. Horanyi on the occasion of his 70th birthday and in recognition of his outstanding contribution to electrochemistry     

Electroreduction of CO2 to Formate with Low Overpotential using Cobalt Pyridine Thiolate Complexes

Electrocatalytic CO₂ reduction to value‐added products provides a viable alternative to the use of carbon sources derived from fossil fuels. Carrying out these transformations at reasonable energetic costs, for example, with low overpotential, remains a challenge. Molecular catalysts allow fine control of activity and selectivity via tuning of their coordination sphere and ligand set. Herein we investigate a series of cobalt(III) pyridine‐thiolate complexes as electrocatalysts for CO₂ reduction. The effect of the ligands and proton sources on activity was examined. We identified bipyridine bis(2‐pyridinethiolato) cobalt(III) hexaflurophosphate as a highly selective catalyst for formate production operating at a low overpotential of 110 mV with a turnover frequency (TOF) of 10 s^?1. Electrokinetic analysis coupled with density functional theory (DFT) computations established the mechanistic pathway, highlighting the role of metal hydride intermediates. The catalysts deactivate via the formation of stable cobalt carbonyl complexes, but the active species could be regenerated upon oxidation and release of coordinated CO ligands.     

Electroreduction of CO2 to Formate with Low Overpotential using Cobalt Pyridine Thiolate Complexes

Electrocatalytic CO₂ reduction to value-added products provides a viable alternative to the use of carbon sources derived from fossil fuels. Carrying out these transformations at reasonable energetic costs, for example, with low overpotential, remains a challenge. Molecular catalysts allow fine control of activity and selectivity via tuning of their coordination sphere and ligand set. Herein we investigate a series of cobalt(III) pyridine-thiolate complexes as electrocatalysts for CO₂ reduction. The effect of the ligands and proton sources on activity was examined. We identified bipyridine bis(2-pyridinethiolato) cobalt(III) hexaflurophosphate as a highly selective catalyst for formate production operating at a low overpotential of 110 mV with a turnover frequency (TOF) of 10 s⁻¹. Electrokinetic analysis coupled with density functional theory (DFT) computations established the mechanistic pathway, highlighting the role of metal hydride intermediates. The catalysts deactivate via the formation of stable cobalt carbonyl complexes, but the active species could be regenerated upon oxidation and release of coordinated CO ligands.     

Phenylboronic acid functionalized SBA-15 for sugar capture

The synthesis and characterization of organic-inorganic hybrid materials that selectively capture sugars from model biomass hydrolysis mixtures are reported. 3-Aminophenylboronic acid (PBA) groups that can reversibly form cyclic esters with 1,2-diols, and 1,3-diols including sugars are attached to mesoporous SBA-15 via different synthetic protocols. In the first route, a coupling agent is used to link PBA and SBA-15, while in the second route poly(acrylic acid) brushes are first grafted from the surface of SBA-15 by surface-initiated atom transfer radical polymerization and PBA is then immobilized. The changes in pore structure, porosity, and pore size due to the loading of organic content are measured by powder X-ray diffraction and nitrogen porosimetry. The increase in organic content after each synthesis step is monitored by thermal gravimetric analysis. Fourier transform infrared spectroscopy and elemental analysis are used to characterize the chemical compositions of the hybrid materials synthesized. D-(+)-Glucose and D-(+)-xylose, being the most commonly present sugars in biomass, are chosen to evaluate the sugar adsorption capacity of the hybrid materials. It is found that the sugar adsorption capacity is determined by the loading of boronic acid groups on the hybrid materials, and the hybrid material synthesized via route two is much better than that through route one for sugar adsorption. Mathematical modeling of the adsorption data indicates that the Langmuir model best describes the sugar adsorption behavior of the hybrid material synthesized through route one, while the Freundlich model fits the data most satisfactorily for the hybrid material prepared via route two. The adsorption kinetics, reusability, and selectivity toward some typical chemicals in cellulose acidic hydrolysis mixtures are also investigated.     

SBA-15的孔壁碳膜修饰对钴基催化剂结构与催化性能的影响

在惰性气体中焙烧SBA-15制得孔壁被碳修饰的SBA- 15C样品,以它和SBA-15为载体,采用等量浸渍法制备了负载型Co基催化剂,并运用X射线衍射、N2物理吸附、程序升温还原、NH3吸附量热等手段对样品进行了表征.结果表明,SBA- 15C仍保持原有的六方有序的中孔结构,但其孔壁经碳修饰后发生增厚,比表面积略有下降...     

Enhancement in the reducibility of cobalt oxides on a mesoporous silica supported cobalt catalyst

The silylation of SBA-15 enhances the reducibility of cobalt oxides on a SBA-15 supported cobalt catalyst, and consequently increases the catalytic activity for Fischer-Tropsch synthesis of hydrocarbons from syngas and selectivity for longer chain products.     

CORM-3 reactivity toward proteins: the crystal structure of a Ru(II) dicarbonyl-lysozyme complex

CORM-3, [fac-Ru(CO)(3)Cl(κ(2)-H(2)NCH(2)CO(2))], is a well-known carbon monoxide releasing molecule (CORM) capable of delivering CO in vivo. Herein we show for the first time that the interactions of CORM-3 with proteins result in the loss of a chloride ion, glycinate, and one CO ligand. The rapid formation of stable adducts between the protein and the remaining cis-Ru(II)(CO)(2) fragments was confirmed by Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES), Liquid-Chromatography Mass Spectrometry (LC-MS), Infrared Spectroscopy (IR), and X-ray crystallography. Three Ru coordination sites are observed in the structure of hen egg white lysozyme crystals soaked with CORM-3. The site with highest Ru occupancy (80%) shows a fac-[(His15)Ru(CO)(2)(H(2)O)(3)] structure.