The Combination of 2D Layered Graphene Oxide and 3D Porous Cellulose Heterogeneous Membranes for Nanofluidic Osmotic Power Generation

Salinity gradient energy, as a type of blue energy, is a promising sustainable energy source. Its energy conversion efficiency is significantly determined by the selective membranes. Recently, nanofluidic membrane made by two-dimensional (2D) nanomaterials (e.g., graphene) with densely packed nanochannels has been considered as a high-efficient membrane in the osmotic power generation research field. Herein, the graphene oxide-cellulose acetate (GO–CA) heterogeneous membrane was assembled by combining a porous CA membrane and a layered GO membrane; the combination of 2D nanochannels and 3D porous structures make it show high surface-charge-governed property and excellent ion transport stability, resulting in an efficient osmotic power harvesting. A power density of about 0.13 W/m² is achieved for the sea–river mimicking system and up to 0.55 W/m² at a 500-fold salinity gradient. With different functions, the CA and GO membranes served as ion storage layer and ion selection layer, respectively. The GO–CA heterogeneous membrane open a promising avenue for fabrication of porous and layered platform for wide potential applications, such as sustainable power generation, water purification, and seawater desalination.     

Miniaturized Salinity Gradient Energy Harvesting Devices

Harvesting salinity gradient energy, also known as “osmotic energy” or “blue energy”, generated from the free energy mixing of seawater and fresh river water provides a renewable and sustainable alternative for circumventing the recent upsurge in global energy consumption. The osmotic pressure resulting from mixing water streams with different salinities can be converted into electrical energy driven by a potential difference or ionic gradients. Reversed-electrodialysis (RED) has become more prominent among the conventional membrane-based separation methodologies due to its higher energy efficiency and lesser susceptibility to membrane fouling than pressure-retarded osmosis (PRO). However, the ion-exchange membranes used for RED systems often encounter limitations while adapting to a real-world system due to their limited pore sizes and internal resistance. The worldwide demand for clean energy production has reinvigorated the interest in salinity gradient energy conversion. In addition to the large energy conversion devices, the miniaturized devices used for powering a portable or wearable micro-device have attracted much attention. This review provides insights into developing miniaturized salinity gradient energy harvesting devices and recent advances in the membranes designed for optimized osmotic power extraction. Furthermore, we present various applications utilizing the salinity gradient energy conversion.     

Nanofluidic osmotic power generators – advanced nanoporous membranes and nanochannels for blue energy harvesting

The increase of energy demand added to the concern for environmental pollution linked to energy generation based on the combustion of fossil fuels has motivated the study and development of new sustainable ways for energy harvesting. Among the different alternatives, the opportunity to generate energy by exploiting the osmotic pressure difference between water sources of different salinities has attracted considerable attention. It is well-known that this objective can be accomplished by employing ion-selective dense membranes. However, so far, the current state of this technology has shown limited performance which hinders its real application. In this context, advanced nanostructured membranes (nanoporous membranes) with high ion flux and selectivity enabling the enhancement of the output power are perceived as a promising strategy to overcome the existing barriers in this technology. While the utilization of nanoporous membranes for osmotic power generation is a relatively new field and therefore, its application for large-scale production is still uncertain, there have been major developments at the laboratory scale in recent years that demonstrate its huge potential. In this review, we introduce a comprehensive analysis of the main fundamental concepts behind osmotic energy generation and how the utilization of nanoporous membranes with tailored ion transport can be a key to the development of high-efficiency blue energy harvesting systems. Also, the document discusses experimental issues related to the different ways to fabricate this new generation of membranes and the different experimental set-ups for the energy-conversion measurements. We highlight the importance of optimizing the experimental variables through the detailed analysis of the influence on the energy capability of geometrical features related to the nanoporous membranes, surface charge density, concentration gradient, temperature, building block integration, and others. Finally, we summarize some representative studies in up-scaled membranes and discuss the main challenges and perspectives of this emerging field.

Advanced nanostructured membranes with high ion flux and selectivity bring new opportunities for generating clean energy by exploiting the osmotic pressure difference between water sources of different salinities.     

Toward Scalable Nanofluidic Osmotic Power Generation from Hypersaline Water Sources with a Metal–Organic Framework Membrane

Nanofluidic membranes have shown great promise in harvesting osmotic energy but its scalablity remains challenging since most studies only tested with a membrane area of ≈10⁻² mm² or smaller. We demonstrate that metal-organic-framework membranes with subnanometer pores can be used for scalable osmotic power generation from hypersaline water sources. Our membrane can be scaled up to a few mm², and the power density can be stabilized at 1.7 W m⁻². We reveal that the key is to improve the out-of-membrane conductance while keeping the membrane's charge selectivity, contradicting the previous conception that the ionic conductivity of the membrane plays the dominating role. We highlight that subnanometer pores are essential to ensure the charge selectivity in hypersaline water sources. Our results suggest the importance to engineer the interplay between the in-membrane and out-of-membrane ion transport properties for scalable osmotic power generation.     

Tailoring A Poly(ether sulfone) Bipolar Membrane: Osmotic-Energy Generator with High Power Density

Osmotic energy, obtained through different concentrations of salt solutions, is recognized as a form of a sustainable energy source. In the past years, membranes derived from asymmetric aromatic compounds have attracted attention because of their low cost and high performance in osmotic energy conversion. The membrane formation process, charging state, functional groups, membrane thickness, and the ion-exchange capacity of the membrane could affect the power generation performance. Among asymmetric membranes, a bipolar membrane could largely promote the ion transport. Here, two polymers with the same poly(ether sulfone) main chain but opposite charges were synthesized to prepare bipolar membranes by a nonsolvent-induced phase separation (NIPS) and spin-coating (SC) method. The maximum power density of the bipolar membrane reaches about 6.2 W m⁻² under a 50-fold salinity gradient, and this result can serve as a reference for the design of bipolar membranes for osmotic energy conversion systems.     

Tailoring A Poly(ether sulfone) Bipolar Membrane: Osmotic‐Energy Generator with High Power Density

Osmotic energy, obtained through different concentrations of salt solutions, is recognized as a form of a sustainable energy source. In the past years, membranes derived from asymmetric aromatic compounds have attracted attention because of their low cost and high performance in osmotic energy conversion. The membrane formation process, charging state, functional groups, membrane thickness, and the ion‐exchange capacity of the membrane could affect the power generation performance. Among asymmetric membranes, a bipolar membrane could largely promote the ion transport. Here, two polymers with the same poly(ether sulfone) main chain but opposite charges were synthesized to prepare bipolar membranes by a nonsolvent‐induced phase separation (NIPS) and spin‐coating (SC) method. The maximum power density of the bipolar membrane reaches about 6.2 W m^?2 under a 50‐fold salinity gradient, and this result can serve as a reference for the design of bipolar membranes for osmotic energy conversion systems.     

Size selective sampling using mobile, 3D nanoporous membranes

We describe the fabrication of 3D membranes with precisely patterned surface nanoporosity and their utilization in size selective sampling. The membranes were self-assembled as porous cubes from lithographically fabricated 2D templates (Leong et al., Langmuir 23:8747–8751, 2007) with face dimensions of 200 μm, volumes of 8 nL, and monodisperse pores ranging in size from approximately 10 μm to 100 nm. As opposed to conventional sampling and filtration schemes where fluid is moved across a static membrane, we demonstrate sampling by instead moving the 3D nanoporous membrane through the fluid. This new scheme allows for straightforward sampling in small volumes, with little to no loss. Membranes with five porous faces and one open face were moved through fluids to sample and retain nanoscale beads and cells based on pore size. Additionally, cells retained within the membranes were subsequently cultured and multiplied using standard cell culture protocols upon retrieval. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Large-Scale and Controllable Syntheses of Covalently-Crosslinked Poly(ionic liquid) Nanoporous Membranes

Herein, we report an exciting synthetic procedure for the scalable and controllable fabrication of covalently crosslinked poly(ionic liquid) (PIL) nanoporous membranes (CPILMs) in water solution under ambient conditions. We found that the pore sizes, flexibility and compositions of freestanding CPILMs can be finely tailored by a rational structural choice of PIL, diketone and aldehyde. Studies on the CPILM formation mechanism revealed that hydrogen bonding-induced phase separation of amino-functionalized homo-PIL between its polar and apolar domains coupled with structural rearrangements due to the Debus Radsizewski reaction-triggered ambient covalent crosslinking process created a stable three-dimensionally interconnected pore system in water solution. Employing structurally stable CPILMs in ion sieving devices resulted in an excellent Li⁺/Mg²⁺ separation efficiency due to the positively charged nature and “Donann” effects. This green, facile yet versatile approach to the production of CPILMs is a conceptually distinct and commercially interesting strategy for making useful nanoporous functional polyelectrolyte membranes.     

Preparation of graded materials by laterally controlled template synthesis

A novel scheme is presented for the synthesis of graded materials by electrodeposition in porous insulating templates. Lateral control of copper electrodeposition in nanoporous alumina membranes is achieved by application of a lateral potential gradient on a thin Au film evaporated on the membrane, used as the cathode. Formation of metal gradients in the membranes is shown to occur under conditions where essentially no gradient is formed on similar bare electrodes. This is attributed to the permanent resistivity of the thin Au film between the pores, which does not disappear upon Cu deposition, allowing a potential gradient to be maintained. Formation of a copper gradient in porous alumina membranes by uniform deposition followed by gradient dissolution is also demonstrated. These results establish the feasibility of controlled electrodeposition and gradient formation in nanoporous insulating templates.     

Recent advances in application of the graphene-based membrane for water purification

Graphene is an atomic layer thick carbon-based material with unique two-dimensional architecture and extraordinary physiochemical, optical, electrical, and mechanical properties. Graphene and its derivatives show significant promises for the development of nanoporous ultrathin filtration membranes capable of molecular separation properties. Graphene-based nanofiltration membranes featuring distinct laminar structures can offer various novel mass-transport phenomena for purifying water, energy storage and separation, gas separation, and proton conductors. The latest developments in water purification techniques through graphene-based membranes including engineering, design, and fabrication of diverse graphene, graphene-oxide, and graphene-composite membranes are provided here in relation to their application paradigm for purifying water. The critical views on pollutant removal mechanisms for water purification along with optimization measures are specially highlighted. In addition, the challenges, shortcomings, and future prospects are pointed out. The green and large-scale synthesis technology of graphene coupling with advanced membrane fabrication techniques can promote these state-of-the-art nanofiltration membranes for a wide range of applications.     

Macromolecular Design Strategies for Preventing Active‐Material Crossover in Non‐Aqueous All‐Organic Redox‐Flow Batteries

Intermittent energy sources, including solar and wind, require scalable, low‐cost, multi‐hour energy storage solutions in order to be effectively incorporated into the grid. All‐Organic non‐aqueous redox‐flow batteries offer a solution, but suffer from rapid capacity fade and low Coulombic efficiency due to the high permeability of redox‐active species across the battery's membrane. Here we show that active‐species crossover is arrested by scaling the membrane's pore size to molecular dimensions and in turn increasing the size of the active material above the membrane's pore‐size exclusion limit. When oligomeric redox‐active organics (RAOs) were paired with microporous polymer membranes, the rate of active‐material crossover was reduced more than 9000‐fold compared to traditional separators at minimal cost to ionic conductivity. This corresponds to an absolute rate of RAO crossover of less than 3 μmol cm⁻² day⁻¹ (for a 1.0 m concentration gradient), which exceeds performance targets recently set forth by the battery industry. This strategy was generalizable to both high and low‐potential RAOs in a variety of non‐aqueous electrolytes, highlighting the versatility of macromolecular design in implementing next‐generation redox‐flow batteries.     

Colloid chemical characteristics of nanoporous glasses with different compositions in solutions of simple and organic electrolytes. 3. Calculation of electrochemical characteristics of membranes in terms of a homogeneous model

The electrosurface characteristics of nanoporous glass membranes–ion concentrations in pores with taking into account the specificity of counterions, electrokinetically mobile charge, the convective component of pore solution electrical conductivity, electroosmotic mobility of a liquid in the field of streaming potential and ion mobilities in pore space–were calculated within the homogeneous model. The effects of the type of counterion (sodium, potassium, ammonium, tetramethylammonium, and tetraethylammonium ions), solution concentration, glass composition, and pore size on the equilibrium and transport characteristics of membrane systems have been analyzed. A method for the determining of electrolyte activity coefficients in the membranes has been proposed.     

Optimizing Membranes for Osmotic Power Generation

The design of ion-selective membranes is the key towards efficient reverse electrodialysis-based osmotic power conversion. The tradeoff between ion selectivity (output voltage) and ion permeability (output current) in existing porous membranes, however, limits the upgradation of power generation efficiency for practical applications. Thus, we provide the simple guidelines based on fundamentals of ion transport in nanofluidics for promoting osmotic power conversion. In addition, we discuss strategies for optimizing membrane performance through analysis of various material parameters in membrane design, such as pore size, surface charge, pore density, membrane thickness, ion pathway, pore order, and ionic diode effect. Lastly, a perspective on the future directions of membrane design to further maximize the efficiency of osmotic power conversion is outlined.     

纳米有序体系的模板合成及其应用

评述了以含有高密度的纳米柱形孔道的Al₂O₃膜和有机聚合物膜为模板,制备金属、合金、氧化物、半导体和聚合物及其复合组份的一维纳米结构有序阵列的几种方法、纳米结构的性质和应用的研究进展。可用于模板合成的方法有电化学沉积法、化学镀、化学聚合、化学气相沉积和溶胶-凝胶法等。取决于孔壁和所填充材料的化学性质,所得阵列既可以是由纳米管也可以是由纳米线组成。这样的有序阵列在光学、磁学、催化及电化学等领域有着重要的应用前景。制备新型复合纳米结构有序阵列、开展纳米器件的研制是模板合成研究领域的重要方向。     

Biomimetic Peptide‐Gated Nanoporous Membrane for On‐Demand Molecule Transport

The controllable molecule transport is crucial to realize many highly valuable applications both in vivo and in vitro. Nanoporous membranes, with nanoscopic pores, high porosity, uniform pore dimensions, and controllable surface chemical properties, hold tremendous potential to achieve this function. Herein, we report a nano‐gating system for on‐demand molecule transport based on a peptide‐gated nanoporous membrane. Acting as gatekeeper, the peptides introduced to the nanoporous membrane provide an opportunity to realize on‐demand on–off states via reversible conformational switching of the peptides. This nano‐gating system offers sustained release and can be used as a sophisticated molecule transport platform for localized drug delivery with a feedback function.     

Efficient Solar-osmotic Power Generation from Bioinspired Anti-fouling 2D WS2 Composite Membranes

Nanofluidic reverse electrodialysis provides an attractive way to harvest osmotic energy. However, most attention was paid to monotonous membrane structure optimization to promote selective ion transport, while the role of external fields and relevant mechanisms are rarely explored. Here, we demonstrate a Kevlar-toughened tungsten disulfide (WS₂) composite membrane with bioinspired serosa-mimetic structures as an efficient osmotic energy generator coupling light. As a result, the output power could be up to 16.43 W m⁻² under irradiation, outperforming traditional two-dimensional (2D) membranes. Both the experiment and simulation uncover that the generated photothermal and photoelectronic effects could synergistically promote the confined ion transport process. In addition, this membrane also possesses great anti-fouling properties, endowing its practical application. This work paves new avenues for sustainable power generation by coupling solar energy.     

Adsorption of argon on mesoporous anodic alumina

We have studied the adsorption of Ar on regular, highly-ordered alumina membranes made by anodization. The straight, non-interconnected pores have nominal diameters of 31 and 83 nm, with a relative dispersion better than 5 % in the pore size. Adsorption isotherms taken on bare membranes with pores of 83 nm present two distinct hysteresis loops. This is found to be a consequence of the fabrication procedure that yields a central circular region formed by open pores surrounded by an outer ring with closed bottom pores of smaller size, about 40 nm. For the membrane with pores of 31 nm, the difference between these pores is much smaller, about 2 nm, and this explains why the isotherms on these membranes show a single hysteresis loop as expected. Detailed real space analysis of the membranes by electron microscopy confirms the adsorption conclusions.     

Molecular simulation of pressure-driven fluid flow in nanoporous membranes

An extended nonequilibrium molecular dynamics technique has been developed to investigate the transport properties of pressure-driven fluid flow in thin nanoporous membranes. Our simulation technique allows the simulation of the pressure-driven permeation of liquids through membranes while keeping a constant driving pressure using fluctuating walls. The flow of argon in the liquid state was simulated on applying an external pressure difference of 2.4x10(6) Pa through the slitlike and cylindrical pores. The volume flux and velocity distribution in the membrane pores were examined as a function of pore size, along with the interaction with the pore walls, and these were compared with values estimated using the Hagen-Poiseuille flow. The calculated velocity strongly depends on the strength of the interaction between the fluid and the atoms in the wall when the pore size is approximately<20sigma. The calculated volume flux also shows a dependence on the interaction between the fluid and the atoms in the wall. The Hagen-Poiseuille law overestimates or underestimates the flux depending on the interaction. From the analysis of calculated results, a good linear correlation between the density of the fluid in the membrane pores and the deviation of the flux estimated from the Hagen-Poiseuille flow was found. This suggests that the flux deviation in nanopore from the Hagen-Poiseuille flow can be predicted based on the fluid density in the pores.     

SEM研究PET核孔膜的光接枝聚合

以PET核孔膜为基材 ,二苯甲酮为引发剂 ,采用光接枝方法实现了丙烯酸和丙烯酰胺在核孔膜上的接枝 ,用扫描电镜 (SEM)直接观察了接枝前后膜的表面形貌 ,考察了不同因素对于接枝位置和接枝效果的影响 .发现膜材料本身特性和接枝反应条件对接枝位置和接枝效果有较大影响 .通过光接枝能够实现膜孔的封盖、缩小、填堵等不同的效果 .采用正侧涂布法反应 ,标准直孔 ,特别是小孔径膜 (0 4 μm) ,不利于孔内的接枝 ,接枝主要在膜的表面 ,从而产生孔封盖效应 .双锥形的非标准直孔 ,由于孔壁的受光性好 ,容易发生孔壁上的接枝从而被填充 .大孔径的膜 (5 μm) ,需要加入交联剂才能在孔壁上形成厚的接枝层 .提出了一种新的反应方法 背侧吸附法 ,反应液依靠毛细作用由膜的底部吸入膜孔 ,膜的向光侧表面不存在反应液 ,接枝只发生在膜孔内 ,从而得到很好的填孔效果 .     

Effect of membrane morphology on the initial rate of protein fouling during microfiltration

Protein fouling remains a major problem in the use of microfiltration for many bioprocessing applications. Experiments were performed to evaluate the effect of membrane morphology and pore structure on protein fouling using different track-etched, isotropic, and asymmetric microfiltration membranes. Fouling of membranes with straight-through pores occurred by pore blockage caused by deposition of large protein aggregates on the membrane surface. However, the rate of blockage was a function of the membrane porosity due to the possibility of multiple pore blockage by a single protein aggregate on high porosity membranes. Membranes with interconnected pores fouled more slowly since the fluid could flow around the blocked pores through the interconnected pore structure. This behavior was quantified using model membrane systems with well-defined pore morphology constructed from track-etch and isotropic membranes in a layered series combination. These results provide important insights into the effects of membrane pore structure and morphology on protein fouling.